Thanks so much for making this video. Im dreaming of my first Sur-Ron sometime next year and your video helps figuring out what I can do to make the bike better! Keep up the excellent content!!!
u guys r rockin it yo...cant wait 4 yur E.R.C. plug n play upgrade .... i'm in line waitin now!!!!...lol...i opt'd 4 the gates belt system... i'm totally happy with it so far... and i do equal road / dirt riding...keep the videos comin
That only allow 2.7" tire. I'm thinking 2000 CR80r or CRF150r forks and triple clamps. They're different but both have about 10" travel, use dirt bike brakes and are light weight
Large increase in load on the motor for a very marginal top speed increase. Running more fieldweakening with a bigger sprocket still allows you to max the rated RPM
You have to upgrade the front fork before you can get a direct mount stem, correct? Do they make a stem that clamps on the steering tube that will prevent the handlebar alignment problem you were talking about.
What was the name off the rear tyre that fits without any adjustments needed on the hubs? (Ebay link doesnt work for me) And are those just stock rims size?
i do not want a bigger rear sprocket... i want a smaller rear wheel and tire plus it seams 16 inch tires is only size you can get in paddle tire for sand or beach rides
Hey what’s up guys I had a question about the orange stem in your link page does that need a spacer or can I just switch that with the stock one? Obviously I don’t know much about bikes and when you click on the link it takes you to Amazon but there’s two sizes 20 and 30 which one fits the stock RSt forks Thank you very much
@@emotobros Awesome.... Question - did you end up trimming the width of these bars or do you prefer them in the full width. I am 5'11" and not sure which way to go.
Liked and sub'd. Just got my Ron two weeks ago and put on the same FOX 40 fork (larger front rotor mounted today, tomorrow brake pads). Have a 55t sprocket on the way as well with a new non-o-ring chain. What air pressure are you running in your FOX? I'm 150lbs and run 70psi but am afraid of bottoming. Thanks....
At 160ish lbs we are running around 85 PSI I believe, you can pump the fork up quite a bit. If you are bottoming on big jumps try adding a click or two of low speed compression.
@@emotobros get the steel first. Choose your three most wanted counts that have a decent spread of options. Add two or three more if there is a lot of interest. Then take the profits or preorders from those that have already bought the steal to get your first order of aluminum
Are you sure it was just your handle bars getting tweaked? My Sur Ron gets tweaked at the top of the shock forks. They straighten right out but very annoying when you’re on the trail
Yo yo, great video! I’ve been trying to find handlebars. Went down to a dirty bike store and got some ProTapers but they don’t fit the stem. And the link (also new link from earlier comments) don’t work. I’d really appreciate your help to find a current model 3” rise compatible HB. Ty!!
Hey, thanks for the support! I believe you can make the dirt bike protapers work and all you need is an adapter. If you’re set on finding the ones we have it may be hard since we don’t know anyone who has them in stock right now
bruh that is my dream bike I am from a poor country (NEPAL) of ASIA I need that bike but it costs half million $ in my country and Iam from a poor family so i cant afford that one :( my father earns 20 $ per week so that will be like the experience of heaven if I ride that one :)
Thanks so much for making this video. Im dreaming of my first Sur-Ron sometime next year and your video helps figuring out what I can do to make the bike better! Keep up the excellent content!!!
did you get it?
u guys r rockin it yo...cant wait 4 yur E.R.C. plug n play upgrade .... i'm in line waitin now!!!!...lol...i opt'd 4 the gates belt system... i'm totally happy with it so far... and i do equal road / dirt riding...keep the videos comin
straight forward, with just the right amount of details 🙏🏼👌🏻
I’ve swapped back and forth between 48t and 52t and I wish someone would make a 50 tooth that’s all I want
Very nice 7075T6 Aluminum Sprockets and Pegs available here: emotobros.com/products/ols/products
Super informative. U guys gotta keep it up. Def one of the best sur ron accounts! Thanks dudes!
Hands down best Sur Ron vids out there!
I put a 64 tooth from Luna and at 6 foot 230lbs. the top speed is 35 mph but the torque and stop and go riding is a blast. Cheers.
Did you stick with the 64T sprocket ?
Where did you get the chain?
Dude !! "Road Princess" is what I named my Sur Ron X
Looking at "cheap upgrades" and seeing the fox forks....
That only allow 2.7" tire. I'm thinking 2000 CR80r or CRF150r forks and triple clamps. They're different but both have about 10" travel, use dirt bike brakes and are light weight
peg spacer brace is pretty cheap and crucial for the off road riders as well imo
Thanks Bro :)
I’d also probably recommend installing a switch on the stock light. It’s on the second you turn the keys so it really annoying.
Thanks for doing this👍
couldn't agree more 👏
road princess here. sur ron upgrades for road use: shimano brake pads, supermoto wheels, luna cycles front light. end of list.
On the direct mount stem: is it a size 20 or 30
Did you ever find out plz lmkk🙏🏽
I think 30 watch sur ronsters new vid called 80mph sur ron
Yes, good content.
What are your thoughts on going lower on the teeth like a 40/42 tooth sprocket
Large increase in load on the motor for a very marginal top speed increase. Running more fieldweakening with a bigger sprocket still allows you to max the rated RPM
You have to upgrade the front fork before you can get a direct mount stem, correct? Do they make a stem that clamps on the steering tube that will prevent the handlebar alignment problem you were talking about.
Direct mount will work fine on the stock SurRon!
suspension dampener sacks out in 400 miles - tried changing oil to 4 different weights did not help much - can find replacement dampener parts
What was the name off the rear tyre that fits without any adjustments needed on the hubs? (Ebay link doesnt work for me)
And are those just stock rims size?
i do not want a bigger rear sprocket... i want a smaller rear wheel and tire plus it seams 16 inch tires is only size you can get in paddle tire for sand or beach rides
Where did you get the seat cover
We have a video on it if you want to check out the videos on our channel
Hey what’s up guys I had a question about the orange stem in your link page does that need a spacer or can I just switch that with the stock one? Obviously I don’t know much about bikes and when you click on the link it takes you to Amazon but there’s two sizes 20 and 30 which one fits the stock RSt forks Thank you very much
Shouldn’t need a spacer. The different sizes are just how tall you want it to be.
Great Videos. You need to update the Handle bar Link.
Just fixed it.
@@emotobros Awesome.... Question - did you end up trimming the width of these bars or do you prefer them in the full width. I am 5'11" and not sure which way to go.
We prefer them full width.
Liked and sub'd. Just got my Ron two weeks ago and put on the same FOX 40 fork (larger front rotor mounted today, tomorrow brake pads). Have a 55t sprocket on the way as well with a new non-o-ring chain. What air pressure are you running in your FOX? I'm 150lbs and run 70psi but am afraid of bottoming. Thanks....
At 160ish lbs we are running around 85 PSI I believe, you can pump the fork up quite a bit. If you are bottoming on big jumps try adding a click or two of low speed compression.
@@MTO_Brothers 2 additional spacers for what weight rider? Thanks!
How does the bike handle crashes with that direct mount stem?
Never had an issue!
road princess?
I want to buy the same handlebars as you. Please tell me the product number or detailed parameters. Thank you
Hey there, links to every part we run are on our website found in the description!
what's up with that swing arm? Looks a little different than mine. You design that or is it just powder coated a different color
I had it powder coated a flaked bronze
What rear shock are you running?
Stock.
Id pay anything for those sprockets!
We have much nicer ones on our website
Where can I get that seat
We made a video on how to do it. You can go to our channel to find it.
Go beavs! You guys located in OR?
Yes! We are in Corvallis currently
52 or 54 tooth around $50 dollars would be good price range
We would be able to do that for laser cut sprocket from steel but if we do machined 7075 Aluminum we wouldn't be making any money. Maybe both options?
@@emotobros get the steel first. Choose your three most wanted counts that have a decent spread of options.
Add two or three more if there is a lot of interest.
Then take the profits or preorders from those that have already bought the steal to get your first order of aluminum
Where did u get that seat
We have a video on it if you go to our channel, and in the description of that video there is a link.
I just hit like for the beer comment and then he drops the road princess and I took it back lol JK
Low cost easy to make? If you have all the gear to make one I guess.
Are you sure it was just your handle bars getting tweaked? My Sur Ron gets tweaked at the top of the shock forks. They straighten right out but very annoying when you’re on the trail
The stock stem rotates around the steering tube. We are sure of what we said.
Yo yo, great video! I’ve been trying to find handlebars. Went down to a dirty bike store and got some ProTapers but they don’t fit the stem. And the link (also new link from earlier comments) don’t work. I’d really appreciate your help to find a current model 3” rise compatible HB. Ty!!
Hey, thanks for the support! I believe you can make the dirt bike protapers work and all you need is an adapter. If you’re set on finding the ones we have it may be hard since we don’t know anyone who has them in stock right now
Road princess lmaoo
bruh that is my dream bike I am from a poor country (NEPAL) of ASIA I need that bike but it costs half million $ in my country and Iam from a poor family so i cant afford that one :( my father earns 20 $ per week so that will be like the experience of heaven if I ride that one :)
After all that, the sprocket is homemade 🙄 what a waste
At the time any link we could find was out of stock so wouldn’t have been much help there either unfortunately.