Is Your Dodge Transmission Not Shifting Must Watch
Вставка
- Опубліковано 13 лют 2020
- If this helps please consider the super thanks sticker
Send Me Junk PO Box 151 Taloga Ok 73667 Fixing The Dodge 48RE Transmission
It will help you a bunch for any project on your car
Solenoid amzn.to/3rFGc69 - Авто та транспорт
If you have a Second gen dodge with shifting problems.. try this.. on yhe back of your alternator there is a wire that come out of the harness and runs over to your fender. If that wire gets too close to your alternator, it will cause interference with the voltage and screw with your transmission. Try and get it as far away from your alternaor as possible, and even better wrap it good with elecrtical tape, or the heating and ac tinfoil tape that has a rubber backing. You're welcome
I’m going to have to try this after replacing my intake manifold on my 1999 Dodge ram 1500 5.2 V8 I noticed I was having shifting problems after hauling a refrigerator. My truck would not get into gear. I put some transmission fluid in and it started back driving good then, right down the street stopped again so now I’m trying to figure out what is the cause of this before I change the transmission. So I will definitely 👍🏾 try this too!
Like a town and country 2004
@@missincredible6087 how did it work out for ya?.. also I hear that there is pressure switch that can be replaced in the pan under the filter.
I followed this video step-by-step and it worked.
Thank you for making this video truck is back up and running👍💯👍
This is exactly what I needed...All my questions were answered!!
I need to know how to get the lines to go to gather
Dodge is a disaster when it comes to transmissions
Not just dodge if you check you will find all three manufacturers plus some of the others are using the same transmission
my '06 1500 has 346,000 miles on it and is just now starting to act up.
And there electronics and wiring are a disaster too
@@detrimundoI have a 1999 Dodge Ram 1500 5.2 320,000 and it’s starting to act up.
2012 ram Replacement transmission today sounds alot better but won't shift now so they wanna put another one in and I feel like it's not the transmission it's something els but I don't know anything about cars fucking sucks
There is a 1'' dia spring that was broken on mine, where you worked but hidden under the valve body, It would not downshift going up hill when I d give it more gas. I also had a TV cable that would bind somtimes. There is another solenoid you didn t show. if your gonna do this clean the top of the transmission where the electrical connector is. Seems to me the problem was more little holes and filters clogging up the solenoids.
The 99 Dodge Ram I have it's a really good truck it was given to me by a family member. Little over 200k and some thousand miles on it I've been going at it for a year and a half trying to get this thing right. It's a Strong transmission the fluid be like a charcoal color but no shades of metal or anything light smell not bad. I just don't know why when I erase the codes after replacing everything in the transmission and then erase the codes and show that's nothing going on with the vehicle anymore. Then when I goes to drive it it gives me that slippage kick feel stall cut off yesterday. I pretty much just parked it in my backyard because I'm done with the truck. I have a little experience on working on my own Vehicles because shops are here these days are very high and scamming.
My friend you saved me tons of cash my truck is running like a champ keep coming with this videos
What was wrong with your truck? Im trying to see if our symptoms are the same.
Hell yea for sure my friend as I took off first gear would shift but I had to speed up to about 50 and let go off the gas in order for second to shift and when I was in the freeway I try passing someone at 70 mph passing gear would go in but it would not shift off passing gear it was crazy
Mine was delayed shifting 1-2 and 2-3 and then somewhat hard downshifting when coming to a stop. I did a shotgun effort and got a 45rfe refurbished valve body and solenoid. Replaced both filters and still the same issue. Guess I'm stuck doing a rebuild of the pump and clutch rings, but Gotta find a mechanic for that one.
@@Wakeupandsniffthecoffee did you solve it?
I finally put it in the transmission shop down the street. They said the solenoid I bought and installed looked like it was high mileage and just cleaned up. They eventually rebuilt the trans, put another solenoid assembly, replaced fluid lines to the oil cooler, pump and $4000 later they got to the end of what they would do and pointing to the computer.
Got the truck back, with issues that say is probably the computer putting it in fail safe mode.
I ordered a computer, programmed for my VIN from car computers online. They said their computers are all resoldered with silver solder, rather than the factory lead. The lead ones, do to the engine compartment location, tended to have cold solder joints over time. Silver has a higher melt point.
My grandson and I got it and swapped it over easily, ourselves. End result is it seems to be running okay, as far as the transmission goes. We had a water pump blow out on the highway, scary thing, but replaced the thermostat and water pump, radiator seemed okay, but my grandson said it's using fluid and temperature goes up over halfway. Guess I'm troubleshooting that next.
You are awesome dude God bless you
Wow youre fast.good job.🤣👍wished they still had drain plugs on your torque conv..to get all that crappy fluid out,even if you blow out the lines still have dirty oil.
I had a broken overdrive accumulator spring. It is common on Second gen rams. It is right inside the pan!
How did you fix that?
I have a problem with my 2007 dodge ram 2500 cummins 48re auto trans. When I pull out in first the trans slips a little and goes to 2500 or higher also won't shift but when you let off the throttle it will. It is only 1rst to 2nd Also when going up a hill if it is in second gear going 2000 it will hard downshift into first going 3000 rpms.
My 2006 Dakota is having a hard time switching gears in drive sometimes when I first start it is not wanting to engage in drive or reverse. I has codes P0700, P0732, and P1776. Any idea what I need to replace?
I did this procedure three years ago, worked beautifully ......now I'm having exact same slipping problem , but I am not getting any trouble codes on my reader , what gives
What’s your advice on a 2004 2500 with Cummins that all the sudden came out of park? It rolled back against my garage door for no reason
mine is a 2004 and it shifts fine unless i put it into reverse first time after start up. i have to let it sit in neutral for about 20 seconds then after that its fine until i drive it again.ive done a few flushes but hasnt helped. i was thinking transmission pump? maybe?
I'm also thinking that the solenoid I got for my truck it was new but no good for my truck because I order it off Amazon and its say it's a Direct Fit for my vehicle. I'm thinking it's a BS part. First time I change my transmission fluid it was okay when I placed the governor's sensor in. I changed the transfer case fluid as well. This time I didn't change it because it was hard to take the bolt off.
My 2005 diesel ram I will have to let off the fuel for it to shift most time and it may downshift after. Early mornings it sometimes has to warm up beat takes off … filter need changing or solenoid ?
I️ have a dodge avenger 2012. When I️ try to reverse it feels like something is pulling it stopping it from reversing. It’ll go back a little then do a little jump and rock back forward
My 2002 2500 won't shift into the last gear. Any thoughts?
Great video man
Thanks good video? I have an 87 dodge Dakota stuck in 2 gear and doesn't shift right? Mines in the shop? I wonder what he's gonna tell me? I could probably do it myself after watching your video thanks
Having an issue with my 2001 dodge ram 2500 I got no reverse mechanic told me we have to drop the transmission to replace the reverse servo then someone told me all I have to do is drop the pan and replace it from there...any advice??
Okay my car is throwing no codes but it won't go past 25 miles an hour unless I go down a hill and it goes past 35 and then it's just no problem is it possibly the shift solenoid I just got done changing the torque converter because I feel like that would be something that wouldn't have a code and possibly make it go into limp mode if it's bad but that wasn't it and since it's throwing no codes I have no idea what the problem could be your advice would be very much appreciated because it look like you know what you're doing
I've got a 2007 4 speed dodge ram, reverse works and won't shift out of 2nd. Any ideas?
Had my 46re transmission rebuilt had it in for about two months or so now when I'm in drive and stop at a red light it just revs up if I shift down to first and go back up to drive it does fine until I come to another stop light or stop sign I got to pull it back down to first and shift first second to drive is that caused by a bad solenoid or something
I have a 05 dodge 1500 hemi. And it will randomly downshift and get stuck in drive, and will stay there unless I shut it off for 10 or 15 seconds then will shift fine until it gets stuck again? Sometimes does it 5 times a day somedays 25, think this solenoid will help?
I have a transmission code on my caravan but it’s still driving normal do you think I should replace the transmission
i have a 2000 dodge ram 1500 we had to do some repairs on it and it was driving fine then one day it was showing issues . i would drive it and it would be fine then i would go to press on the gas and the RPMS would rise but truck MPH wouldnt and she wouldnt shift . we would get out and check the plug on trans turn truck off and restart and it would drive fine for a bit then go back to high RPMS and no shifting or accelerating . we replaced some weird solenoid on a metal bracket and a plug the bracket has 2 solenoids on it . truck runs and sounds great except ....i dont think its shifting into 4th gear . any ideas ? trans fluid is clean not burnt and full.
I have a dodge jurney sxt 3,6 automatic and it's stucked in 3rd gear. I have changed the solenoid pack and the shifting solenoid it was costly. I also did a service on my transmission but the car is still stuck in 3rd gear need advice 😢
Will this be the same problem for an 06 ram 1500 4.7 automatic transmission im stuck in 2nd gear as well
Mine went out. Replaced it and the filter, drove for a few months and started throwing a code again.. not sure wth the deal is
Hi u know why my 06 charger rt start having problems when weather is hot. In the morning works fine but. Afternoon when ho back home. Starts slipping. How to know if needs oil sini there is not. Stick on it. Please lmk thanks
thanks for your help in advance
Hell yeah dude I’m doin this to my truck tomorrow kuz it’s not shifting into second when warmed up.
Did I ever find the issue , I have the same problem
My 2000 Dodge Dakota RT 5.9 isn't shifting out of 1st and my dad and I replaced the transmission filter and fluid why does this happen..
Answer me this. I have a 2006 dodge Dakota 3.7 liter 2wd and I bought the truck and it didn’t have reverse but it had drive it goes into every gear but like it would just rev up and wouldn’t go anywhere now it’s the opposite it has reverse goes into every gear still but when you put it in drive it just revs up won’t go anywhere
My 99 Dodge Ram 1500 5.2L 4XX Transmission Still Slips after I change The Governor & Solenoid Sensors in it. I don't know it's doing it. I followed the same procedure that you did I erased the codes it was riding good for some hours then it started by slipping so I just pretty much parked the truck.
With this problem can you reverse ? My dodge nitro is stuck in 1 gear or reverse
I have an 01 ram 1500 and it stays at 4000rpm at 55-65mph. I don’t feel it upshifting. Could this be the governor?
Is this why it won't shift out of first unless I floor it then it will shift normal until I come. Again to take back off
Thank you bro, I'll try it on my 1994 1500
I tried it and it worked....shift like a champion....sold it...new owner loves it
i have 2006 dodge durango its not changing out of first .fluid is clean and there is no slipping also fluid level is good
Did you get it fixed?
Mine is doing something similar so I would like to get some ideas.
Does anybody know where the 2004 dodge intrepid se transmission fluid pressure sensors located?
I really liked your video it was straight forward you did explain how many bolts and screws and what size they are . However you didn't mention how much to torque the transmission pan bolts down and did you reuse the original transmission pan gasket or replace it
I've got to do this same job. And I believe I can get it done with enough information.
Thanks.
I just did this and re used the original oil pan gasket. Has not leaked a drop. The original is way better quality than what comes in the new kits
Did you use any RTV ? I bought my truck used and the previous owner rebuilt the transmission himself in his garage. I'm sure I may need a new transmission gasket.
I have a 1500 Dodge it goes into gear for a minute or two and goes to newtrel I can turn it off a few and it pulls again please help
Would that fix the reverse or no
I was told at AutoZone that it's cheaper if i don't have a govern and higher if i do. How do i know if i have a govern if i can't drive as fast due to the silonoid
Very helpful mayne
My 2002 dodge dakota 3.9 sometimes shift out of 1 sometimes it don’t you got any solutions?
Is this work on a 2016 dodge charger too or just trucks
I don't know if I will get a response but I hope so, any ideas would be appreciated.. I have a 2011 Ram Dakota 3.7 v6 that will not reverse. In drive it shifts fine, no other apparent issues, but when I put in reverse, I can hear it shift into gear I think, but when I hit the gas, it revs like it is in neutral. Only thing I have done that might have caused it was pressure wash the undercarriage a little bit.
Have the same issue, could be bad solenoids
What gear was it stuck in?
My brother n law has a 2000 Dakota 4x4 that’s had 3 transmissions swapped out and it’s still not shifting properly, won’t downshift to first or go into overdrive. He parked it.
Would this be the issue on any transmission? 2002 Durango?
Would this work on a 2015 8 speed 4x4?
So what trans exactly does this cover
My 95 dodge ram 1500 4x4 transmission has been rebuilt I installed it and it's stuck in first what should I check it's an early 95 so it's mechanical not electrical
Did you put a new gasket on
Hey where do the solenoid replacement kit
Best transmission
My dodge does it intermittently. No warning lights on at all. No leaks at all. Revs but doesn't shift past 2nd or 3rd.
Is that the same for the 5.9 gas version
My 2001 dodge Dakota is parked for now was falling into neutral out of drive from 40mph and having issues getting over 20mph fluid is good and all but. It's my first vehicle with 276k miles on it engine has only been rebuilt.
I know this old comment but did you ever figure out what was wrong? My 01 Dakota is doing the same
I got a 2000 dodge Dakota when I put it in drive truck don't move but I can here tranny spinning dose not sound good any idea
Getting a P0735 struggling with abnormal shifting gears dodge Durango, Anyone experience such thing?
what year was this dodge?
So Dodge Dakota is not like a standard Chevy truck that you can adjust the shifter linkage to get first gear
I have an 05 Dakota with the 4.7 L engine. One day the transmission went into limp mode. Took it to a transmission shop, and he replaced the shift solenoid. That fixed it for one day. I took it to another shop that could hook it up to the computer, and he said it was a shift solenoid! When I told him that it had just been replaced, he suggested that I replace the transmission. I did as he suggested and authorized the work. That lasted two days. He then replace the solenoid, which lasted one more day. He then replace the transmission again, and then swapped out the ECM twice. That worked for two days. I took it back and told him that it must be an electrical problem, and am unsure what he did that time, but it worked for almost a year. The truck just slipped into limp mode again today. I was able to make it home, but wonder what he did to repair it. I asked, but he said he change the shift solenoid again. Any ideas what he might have done to the electrical to make it work?
This feels like the problem im beginning with my dodge magnum. Did you come to a solution?
@@hankmoody6996 found out he chased all the ground punts in the truck and cleaned and reattached them. It had a faulty ground contact somewhere, I believe on the firewall near the computer. Been working great since…
@@Uglee1 great just screenshotted this incase it comes in handy. Thanks for the quick reply !
@@hankmoody6996 👍
Mine,I disconnected the overdrive button wire,now it runs through all gears
Is this the same on a 68rfe. 08 2500. Auto. And Did it throw a code. Thanks. New to the cummins world 😂
I have a 2004 dodge ram 1500 5.7, it was running fine up until a week ago. Now when i take off its either taking off in 2nd or 3rd gears sounds like and will have high rmps. I had waterpump and thermostat changed before this occured, would that be a cause of it?
Hi did you figure out about your transmission my 05 is doing the same right now
Hey John, I have a 2006 Dodge Ram 2500 5.9 cummins 4x4. It throws a P0868 low pressure code After reaching over 50-55mph then goes into limp mode. I reset the code and then runs back to normal and again. It has the ABS/BRAKE Light on After I reset codes the abs/brake light turns on after reaching over approximately 20mph. Then the P0868 code triggers. I have to reset codes to get the truck off of LIMP MODE. Im LOST 🤦🏽♂️😞
Needs a transmission
this video was wassup. just a note though next time dodges call for 35 inches torque with there filters i just ordered mine for when i do my flush
I have an 07 Dakota, it jolted and went to neutral while driving, and the oil light came on then went back into gear. Any idea what it was?
Check your fluid
Hello. I have a 2006 dodge charger that won't shift from 1st gear to 2nd, Automatic.it makes a noisy sound. What do you suggest will fix it?
Sounds like you need a rebuild is that the case?
What year truck is this
Thanks!
I have a 2012 journey 3.6 awd. just out of nowhere it will not shift out if 3rd only way to get up to 55 is have it at 5500 rmp..diagnostics machine tells me it the 2nd and the 5th gear ratio..
So I had all speed sensors changed filter and new fluid still won't shift..let me correct this it acts normal for the first 5 mins of driving in the morning when its cold..
Any help would be very much greatly appreciated
Hey man did you ever figure out the issue? My 1991 goes 1-3 gear but won’t kick into overdrive either
My 2007 Charger so.etimes revs high in between shifting. Then it runs fine. If I let it warm up at times it runs fine. But if I just start it a go at times it revs high before if shifts. Thanks
Yea that’s a common dodge trans issue. It’s called flaring when it revs during shifting
If I stop and put it in park then put it in dri e it goes away
Why did you not torqe anything?
How’s this truck doing now
What's trans is this?
Hello does this include 545 RFE transmission out of 2006 Ram truck ? It doesn't shift period . 5.7 hemi any ideas ?7 codes
If it doesn’t shift you have bigger problems
My ram 1500 has a rpm of 2 but now it wont go in reverse. Could it be the torque converter isnt put in well? ( i just replaced its motor)
Did you fix it I have no reverse in mine
Where that solenoid is on y’all’s trucks mine is flat there with no solenoid.. I’m at a loss
How I fix the parking paw
I have a 2006 dodge ram 2500 the issue is that after the teuck reaches normal temperature the transmission starts to shift up and down and sometimes it gets stuck in 3rd gear. But i turn it off starts shifting normal. Any idea what could it be? Transmission was rebuilt but still has the same issue
this solenoid is the same issue we were having super easy to replace often transmission rebuilders don’t replace all them pull codes first i bet you it has one even if the engine light isn’t on
@@RightOnJohn383 thanks im going to try that. Hopefully that fix the problem 😃
I got a 2000 Dakota 4.7 I only have 1st and 2nd gear takes a second to go into drive and engine runs a little weird sometime throws a p0700 code do you think that could be the issue possibly or is the valve body and crank sensor?
Id adjust bands before I replace this
Trans valve body
Check for recall
Let dealer fix it for free
If not see if you can change yours out..
Fix it?...no test drive?
I’m not downshifting when I’m driving, does anybody know what that could be
Does that include a 1999 Dodge short bed single cab 1500 ram or do they vary
I want an update. Did you try this because I have a 1999 Dodge ram 5.2 and I’m struggling because my fluid is very dark and my mechanic is saying that I need to change my transmission but I think if I change the solenoid I should be able to drive it for a while longer and then change the transmission.
I have a 2011 Dodge Charger SE. The gear shifter moves between gears but the car does not respond. Stays in park, will not go into drive or reverse. please help.
If you find the problem to your transmission let me know
Good day. Can you please tell me if the tailgate of the Dodge Durango 2004 differs from the Dodge Durango 2007 rating?
My 99 Dodge Dakota has a hard time getting past 2nd gear. Now I can’t drive a few blocks before I lose reverse drive 1&2.
Bad pump or need I need a new filter/fluid?
I have a Dodge Durango 2007 and when I drive it up shifts to second then to 3rd and sounds like it drops back down to 2nd while I’m still accelerating... can you tell me what might be the problem? Please thanks
It sounds like its hunting for gears check your grounds and clean them
@@RightOnJohn383 Do you have a video on checking and cleaning grounds? I don't want to sent my ECU in for repair until I've exhausted all options... seeing as the transmission has already been rebuilt twice without resolving the problem of no shifting into overdrive. Thx...
Did you reuse the gasket you had on the pan or did you put a new one??
It’s a reusable gasket
What was the symptoms ? Ive got a 2004 4.7 , starting from a stop, seems like it's starting in 2nd gear all of the sudden...any ideas ??
Adjust bands first if not this solenoid is a good start
Shift solenoid.
See if theirs a recall on yours first.
If not properly look it up,you just might be able to switch it out yourself
Did you ever fix your problem? Mines doin the same. Only got 2 and 3rd gear...
@@tobysteele6394 I changed both filters,fluid..been fine for 2 years..the canister filter was kinda loose...good luck
I have an dodge 2500 v10 she won't shift out of 1st would this fix my problem
it might but try a band adjustment first
What if my Dodge Ram shifts into park,reverse but hops over drive into 4th gear which that is the only gear it can drive in now . What do you think?
Probably solenoid
Mine doing same