Thank you for watching! OBD2 Scanner: amzn.to/43UwyBg Check out AllDatadiy repair manuals: www.gopjn.com/t/SENKTklLS01DSE1NS0lOQ0dKRk9LTw Use code AD10VA for 15% off one-year subscriptions for any US Order Check out my merch: easyautofix.creator-spring.com/ Have car-related questions? Check out JustAnswer! They have verified auto mechanics that are available as live help 24/7: justanswer.9pctbx.net/qnj74y Buy a new shift solenoid: advanceautoparts.rt8x.net/rnPVQ3 Here are some of my favorite items that you might like: Tools: amzn.to/3xNDb8g Car Vacuum: amzn.to/3EjhPSJ Cleaning Tools: amzn.to/3El7dCG Water Repellency Wiper Blade: amzn.to/3utvK50 Cleaning Gel For Cars: amzn.to/36NIiMr Portable Air Pump for Car Tires: amzn.to/3uBuPzA Headlight Restoration Kit: amzn.to/3qDpOVH Amp Jump Starter: amzn.to/3pMd0vx
I just got new tires and hit a big bump and only had 1st gear.replaced the plastic bushing and half washer on shift cable Then was driving about 30 mins ok then just had 1st gear all of a sudden. 2008 chyrsler Sebring convertible 3.5 never again.👎 sensor's then gone.😂
@ Easy Autofix Sir the car transmission is making whinning noise and delays in shifting gears, I checked for the fuel level is Ok, I checked for the oil still fresh not burned, I checked for any leaks no any leaks, I open the pan, but there were no any metal shavings on the magnets no any particles on the fluid, I decided to change the transmission filter, I checked and open the valve body no any clogs on the passages, I removed all solenoids I tested them all, and one was not working, I changed it with new one, I put back everything I test drive the vehicle no more whinning noise at all and gears are changing smoothly, but after two days as i drive reaching speed of 100 mph, the whinning noise started again, and the car struggles to exceed speed of 100mph, the RPM goes high and the speed is not achieved, I checked fluid level is OK. what can be the problem, and what can be done sir? Kindly help with ideas.
My O/D light keeps flashing on my ford f150 year 2000 and yes when I shift my gears on N/D/R etc it gives this jerk motion is that the solenoid or speed sensor?
Taurus 02. Starting cold, It wont shift out of 1rst gear. After 5 minutes warming up, I can then shift freely all day until it cools. New Transmission fluid and filter.
Would a bad Shift Solenoid be the cause of my 1995 Dodge Ram 1500 not moving out of park? I won't go frontward or backward. I bought brand new transmission fluid and oil and that didn't fix it... I was thinking along the lines of a linkage problem.
Yeah this comments totally off the subject here but I just got to say... you sound EXACTLY like the guest star that played a dude named CANVAS on Anger Management sitcom..😊
My nissan car when you drive cant exceed speed of 100, my transmission fluid is ok and on tge required level, but ecen if yiu press the gas pedal yo the bottom, doesnt exceed sich speed, what can be the problem? Kindly hep with ideas of how to fix.
How do I tell if it's just the solenoid switch, or the entire transmission? Because I hope it's the former because replacing just the solenoid would be much cheaper than replacing the whole tranny.
You need to replace the Sputnik vacuum valve under the transmission picke plate. Its easy to spot, because it's right behind the gear nook. Hope this helps👍
My 2001 lesabre started with severe delayed shifting, first to second wasn't bad but second to third would slam into gear, I did some research and found that this was a known problem on some lesabre models. The temporary fix if you can call it that is to shut the car off which resets the module, leave it off for a couple of minutes then it shifts normally again until it does it again, sometimes it lasts for a bit but then the problem comes back, with close to 300,000 miles it was time to replace all five solonoids. I purchased all five as a package deal off eBay, all OEM parts, the first thing is to prepare the patient by raising the rear and front of the car, I used ramps on the rear and jacked up the front as high as I could because you need to lower the subframe and remove the strut cv axle and everything necessary to gain access to the side cover of the transmission. Remove the cover and it's relatively easy after that except for one thing, the wiring harness that connects the solonoids together, from being heated and cooled a million times the clips that hold the connectors are more brittle than Bob Barkers back, one broke on me and there's no real way to secure it thst I felt confident with. I went to my local Buick dealer and go my surprise they still made the harness, and it could be mine for the poultry sum of 350.00 dollars. I told him I'd let him know, went home and low and behold I found one on eBay for 25 bucks, the only thing was that now I had to wait almost a week with the car in pieces taking up my driveway. I received the part put everything back together and prayed. That was about five years ago and she's been shifting perfect ever since, all told parts, the side cover gasket was the most, second to the solonoids at 55 bucks, all five solonoids were 75 from eBay,,the whole job was around maybe 175 including trans fluid, you loss a lot from the side cover, I also removed and replaced the trans filter while I was at it. I've been working on cars for almost 40 years now, I wouldn't recommend doing if yourself for a beginner but then again, everybody has to start somewhere, power tools aren't necessary but they make the job to faster, with hand tools it's a lot of nuts and bolts to remove.
appreciate your comments....Have an05 LeSabre. Sometimes rough bump after initial shift into drive. Five solenoids? Saw a separate reference about 4 solenoids..wonder what the 5th one is. Could u mention the specific seller on Ebay? Thanks for t your excellent post..jP
Thank you so much young man. I have a 2016 Ford Focus and had the clutch replaced and my car is still experiencing these symptoms and by watching your video I realized my car is going into limp mode. The dealership will not fix anything else other than the clutch that’s under warranty unless I cough up some more money. Thank you!
Before running out and buying those solenoids try replacing the Transmission Control Module that is located inside the air filter box, (Chevy Impala) no tools required and it fixed my problem. They will run you about $20 at the salvage yard, fault P0700.! It takes 5 minutes to replace! You're Welcome
@@markolsen7438 that depends. An older GM sure,a new one no thank you. Buy a toyota,with proper maintenance,will last forever. Fuck made in America bullshit pride
@@Francofit nope still driving it like this feels like it’s getting worse haha I’ll buy a junkyard trans and swap the parts the valve body and solenoids. If that doesn’t work I’m screwed lol but it should
Right on brother ' you've given me hope. 👍 As I drive my 2009 F-150 4×4, the automatic transmission will shift into first gear smoothly, it shifts into second smoothly, then it clunks sharply into third gear at around 35 to 40 mph. Viewing your video, I'm hoping it is something as simple as a solenoide. Thanks again 👍🙏
How much does it cost to fix this item at a dealership? I'm a widow, I can't do this myself. I have job interviews to get to before I can afford to fix it, or pay rent. Thank you for the video. It explains what the truck just did. Take care, stay safe, have a nice day. 👵✌️🖖
Toyota dealership tried to say my transmission needs to be replaced. I said no thanks....... Just change the fluid, strainer, gaskets and shift solenoid. 260 k mile tundra Guess what Runs like I just drove it off the showroom floor!🙏✌
Thanks, is it possible to get this kind of issue without having the check engine lights on and detected on the scanner? My car has similar symptoms but nothing being detected when it scanned
@@anggadwikara6881 I didn’t replace them because of the fact of not getting codes but I researched a lot can’t find the main video I seen but I’ll find it for you but this may help wanted to try today but it started to rain I will update you when I put the ground wire on to see if it works
Do you always get a code for a shift solenoid? My trans stays stuck in a gear. It doesn't act like a slipping transmission to me. It's a 2003 Ford F-250 with a 6.0
I have a 6l80e and 2-3 slips sometimes but smooth on highway or if I’m giving it enough gas. Changed fluid and it’s still the same not better or worse. Trans never overheats. Always stays 140-180
@@smashadams85100 nah not in my case unfortunately. Now im waiting to change trans fluid and adding a bottle of that seafoam transtune and see of that helps. Adding some tomy existing fluid seemed to have helped some
I’m currently having this problem with the same transmission, my fluid was burned and it wasn’t much of it in there at all. I can’t find any solenoids and I’m hoping to avoid buying the entire valve body. Have you found a fix yet?
2 days ago my older 2000 F250 (only 136,000 miles on it) went "clunk" and the whole truck lurched - then it was like it was stuck in a low gear. I still had to drive a mile home - it did this 3 more times, lurching like it was about to stop, stuck in a low gear and higher rpm's - but it got me and my groceries home - and I haven't touched it since. Least now I know what to tell the mechanic. Thanks.
Great video, I have a 2000 JEEP WJ 4.7 and it started shifting hard from 1-2 and the kickdown from 4 to 2nd is really hard, do you have any idea on were to start? Cheers man!
@@e.l.9589 It rusted out to be a disk plate set and needs replacing. The OEM diagnostic tool made an adaptation for the gearbox and now it works smoothly. The guy told me that would last 100-200km but I did 700km and still shifts perfectly smooth. Cheers
sometimes my car could not shift gear the engine just revs and that is it.so I went to change transmission oil it was black.put new one and went to a shop that uses a special machine that is for changing transmission oil .believe it or not at my last transmission oil the people told me they do notnhave the proper equipment sp they could oybtake out only 40% old oil.noq they took 90%of the old oil. now the car shifts way better than before and so far does not stuck and does thebold problem but I still think new solenoids would help.
I have a 2010 nissan rogue cvt level is good but 80% of the time when shifting from P to R or D it shifts pretty hard, any idea if a bad valve body could be the culprit? (Mounts are good)
Thank you for the information. Driving home last night (any where from 40 - 70 mph) with no stops, until in town, my 2009 Chrysler Town & Country stalled. Started up in neutral, shift to Drive, and it stalled again. Kept trying, was able to get it going and found it would run/drive using manual D1, D2, etc. Works okay in reverse. No engine light though? Prior to this stalling problem I have noticed at stop lights, the engine seems to idle at higher RPM. But not all the time. Taking it to the transmission shop for professional diagnosis. Have a great Labor Day weekend!
I know this is an old comment but did you find out what the problem was? My 2000 ford expedition 4.6L V8 Triton XLT 4 wheel drive is doing similar, and there is no check engine light, but my ABS light is on. My vehicle won't even go in reverse or allow me to shift to Park. I only can drive if I put the gear in 2.😬 I was told it was my Shift Solenoid that needs replacing.🤔
@@flowersfam3462Had a 2,000 bid to open it up and work on it. But the mechanic did not really want to do it. The other transmission shop would not even consider checking the solenoid. So I chose to replace the transmission (they gave me a 3 year warranty on the new one). Three days after it was fixed my battery died. The one fella told me his wife's truck was shifting bad and it was because the battery was going bad! Some kind of electronic issue! I'm putting that fact out of my mind to not second guess my purchase!
Hello everyone. I'm wondering if you could help me to help my dad. His work van is a 2001 Econoline2001 e350 it won't go into drive it only will go into neutral Park and reverse. He took it to a shop and paid $200 just for them to look at it and they told him he needed a new transmission. The person that sold it to him told him to never let anybody tell him it was the transmission if that happened that it was the solenoids. The linkage being loose. Does anybody know anything about this at all I've looked everywhere and I can't seem to find anything
You need a new car bro, if one of those is bad, it means its over for your car, can't be replaced, they don't make those and if they did make em, you cant remove your current one as its permanently welded with gorilla glue ultra super duper strength Silverback edition.
@@bosspranks8349 i just pulled my 2nd shift solenoid out of it with no problem with being welded in by the motors heat like some would think. And my wifes car has high milage lol. but i still replaced mine but its doing the same and not shifting.
2021 Hyundai Tuscon SEL 145,000 miles between 40-55 mph there is a slight shimmy or shutter for 3-4 seconds then back to normal no service engine lighten back to normal no service engine light
Had my 460le rebuilt with monster trans kit, the cooler installed line broke and I got it towed and replaced asap, 1 week later I get a CEL for stuck solenoid open. Could it be dirty fluid or something worse? Drives and shifts fine although I parked it since running this code. Only thing noticed is my 2nd gear shift kit isn't thumping into 2nd like it used before changing cooler and fluid
A friend's Chevrolet truck went into "limp mode" and wouldn't change into 3rd gear. He fired the parts cannon and had spent all kinds of $$ trying to figure out what it was. I came over while he and his "automotive tech" neighbor were standing around the truck scratching their heads. Lol when I asked if he tried replacing the transmission shift solenoid his "tech" buddy immediately blurted out "thanks but it wouldn't shift at all if it was bad." Long story short.... It was the solenoid. I think he'd spend a couple hundred bucks already. Lol $18 for the solenoid, and around $40 bucks for pan gasket and new ATF was all he really needed.
Changed my whole valve body out and it shifts out good but when I stop it’s like I’m stuck in a hole and then when I accelerate to move forward it kicks back into gear and goes. Does the same when I’m reversing. Stalls for a minute and then I press the gas it bucks and then starts to move. Other than that it shifts fine.
This is a long shot hoping someone will chime in with some advice. I just had my transmission rebuild on a 2015 gmc Sierra 5.3. - I feel like the mechanic has done something incorrect. he has had it for a month now. has retired it to me a few times and the truck is not shifting correct. once up to full operating temp it will slip badly going into 2nd. Instead of shifting it will go into neutral and the revs will go up fast until I let off the gas , then it will usually clunk into gear , it goes through all the other gears fairly normally. he is claiming that the truck has to go thru a "learn cycle" than can take multiple days of driving it with these symptoms. sometimes it will just stick in second until oi come to a complete stop then it will go back to normal for a little while. it is also leaking a considerable amount of fluid, took it back twice for just the fluid leak and he keeps saying its fixed but then I take it home and its leaking. he said "sometimes it will leak a little at first"....none of this seems correct. the truck only has 80,000 miles on it and I do not think it even needed a transmission , the whining noise it was making that brought me in the begin with has not been resolved with the rebuild. this shop is where my warranty required me to take it and has very good reviews so I felt like it was a reputable shop. Is it true that a 2015 gmc transmission requires a re-learn period like this and do these sound like normal symptoms of that? I paid a lot of money for this truck and feel like this guy may have destroyed it. the amount of time it is taking is also excessive seeming to me. PS there is no check engine light or trans light coming on and this is why he says nothing is wrong. he has finally agreed it shouldn't be leaking trans fluid so it is back there again for that to be fixed.
Say what🤔 Were made in HIS image. HE made us with the power of free choice A good prayer: I'm a sinner JESUS please forgive me for all my sins I know you shed your Blood for me on the cross at Calvary. Thank you JESUS for my salvation and for shedding they Blood for me. I love you JESUS. Romans 10:5/10 ct...❤️k JESUSisLord!Amen... Amen.. If you'd like to call someone who cares 83 For Truth. bc you don't know when you'll die? .y r u hesitant. . .
I know this video is a few years old I don't know if you'll get this message or not I have a 2009 Chevy Malibu 2.4 4 speed no engine light comes on but it will not shift into overdrive or shift out of 3rd gear I'm driving 70 mph and the RPMs are like 4,000 when it should be like 25 any suggestions transmission fluid is good I'm thinking a solenoid but why would there not be a engine code
Great video thank u!! I drive a 08 Lexus IS250. When slowing down and almost about to come to a complete stop I feel a slight bump. Do you know what that can be related to?? I have no check engine light. And I just got the car so I'm not sure if the training fluid or filters was ever change.
@@2righteous I got an update. So I did an engine oil flush using motor medic. I then change my engine oil, filter, and spark plugs, and did a full throttle buddy cleaning down to removing the intake manifold and soaking the intake passages which were full of carbon and slosh. I used seafoam for that. Additionally, I change my front and rear brakes complete with new rotors. Miraculously that surge or bump I was feeling when coming to a complete stop has now disappeared. I'm guessing it had something to do with the carbon cleaning I did and not at all transmission related. What ever it was I no longer have that issue.🤗
I have 2005 ford focus, no reverse or barely can go forward! When in N I cannot push it backwards, but can push forwards. I am not getting any codes? Any information? Could it still be a solenoid?
My brother has a 16 highcountry with the 5.3 9l80 I believe and sometimes while driving it will go out of overdrive and run at 3000rpm. If he turns the truck off and then on again, it works fine until he hits a bump. We cant figure out what it is and the mechanic is trying to sell him a new transmission! Any help is appreciated
Is it possible to make the TV cable adjustment too many times? If so, what are the repercussions of doing that? I've been having issues, for about 6 months now, with my 94 Jeep XJ automatic shifting either too quick or too late, very erratic overall. I've replaced the TPS and have done this adjustment probably 20-25 times over the coarse of the last 6 mos. Yesterday, it started to not shift at all on the highway. I would press the gas and the RPMs would go up over 3000, but it would not accelerate and I had to coast it into a gas station. Went out and made the TV cable adjustment and then would crank, but not start. Repeated the adjustment 5-6 times and still wouldn't start. Unplugged the TPS and it started right up. Attempted to drive it the 5 miles home, with the TPS unplugged, but the same issue came up with it not shifting or accelerating. Is this what they call "limp mode"? Anyway, I pull over and plug the TPS back and try to start it and this time it started and mysteriously drove and shifted much better, although still not perfectly. Should I be looking at something in the transmission itself at this point? It's full of fluid and it's the stock AW4 tranny. Does any of this sound related to a neutral safety switch problem at all? Thanks for any help anyone can offer.
Hi, my Chevy Blazer 3.6 2020 has vibration, i think its from transmission, i shifted gearbox in L, when shifting from manually gear box cannot shift in 3 gear. can you advice me what to do?
Ok in my 05 trailblazer there is 2 solenoid 1-2 2-3 or 3-4 not sure but there's 2 my truck shifts 1-2 but no 3-4 , my question is is which solenoid is the bad one? How do I tell the 1-2 from the 3-4? They look exactly the same?
I have a 2015 Hyundai Santa Fe 2.4L AWD. Transmission shift out of second in Automatic but I can shift it manually bye moving the shift lever to the right. Need help.
Mines p0773 and still runs fine.. I got it back from a mechanic with this code and when I took it to him I had no codes or CEL on. He replaced my valve cover gasket and spark plugs. Could this cause this solenoid to malfunction or something??
Am using 2004 honda Accord 3.0 v6 My problem is whn i kick full acceleration rip goes high and rpm is cutting off.. not shifting to next gear .but when i drive normally all gears are shifting normal.. only in full throttle rpm is cutting and not shifting anyone knw why?
So basically if this is bad & I take it to a transmission shop…There gonna say o sorry sir but it’s gonna be 2500 to fix your transmission? SMH…People LEARN how to fix your own 💩
Hi everyone! Im about to work on a Volvo c30 transmission that is not engaging 1st and 3rd gears just 2nd and 4th anyone knows what could be causing the problem!? Thank you! I suspect that could be a bad solenoid what you guys think!?
Hi! How are you? I have a problem with my ram 5.7 2016 with automatic gearbox. The problem is that when the truck need to put the 5th gear the revolutions going up but the gear is not into. Is like you press the clutch in a manual car and accelerate. I changed the valves box and also the solenoides for the another model but the same piece, because my ram has an grey connector and I puted a green one. Thanks so much 😁
I have a 1995 Silverado 5.7L 4x4.... Put in gear, and it barely moves just high rpms and takes forever to get to 30mph then boom we are off to the races runs like a champ, what's my issue?
This was pretty good. Straight forward!!! Another straight forward idea is, don’t buy US trucks. They’re ALL garbage. Buy Toyotas. Hell even Nissans are way better with less headaches
My car first symptom was the check transmission light that came on with a flashing drive gear light while I was going 60 the speed limit on the freeway and the car switching to lymph mode as soon as the rpm arrow went above number 3 and got stuck there. The car started driving at least 40 mph while the speedometer still said I was going 60. I parked the car right on the side of the highway to let it cool off. Fast forward to 20 minutes later, The car was back to driving normally again. Following that about a couple of weeks later, I noticed weird gear shift delays regardless what gear I switched to unless I put it into park and following that, It makes a clunk noise coming directly from the transmission when it finally does switch. When I accelerate and reach close to 20 mph, A typical car with an automatic transmission switches to higher gears but mine gets stuck in gear and the engine starts revving harder and it jerks back to its appropriate gear. Upon inspection I did notice that the transmission is very low on fluid and the fluid is almost black. I took my car to the mechanic for a diagnostic and a fluid with filter and gasket change where he told me that the transmission needs to be replaced and upon further questioning, He told me that there’s no point in changing the fluid because the transmission is basically bare medal rubbing debris and that it would make the transmission run worse. It’s been about a month now and the car runs basically the same as it did when I visited the mechanic with no transmission failure and I’m thinking about bringing it to another mechanic for a second opinion when I have money. I would be more then glad to hear your guy’s opinions and suggestions if any as well. I’m very hopeful that the first mechanic was wrong.
Good video.....my chrysler 300 2006 touring ...i can put in R and D when i drive it i feel no change in gears engine feel like it losing power hear a strange knocking in engine the knock dont come until about 4 or 5 mins of engine on cut i car off then back on the knock gone for awhile then come back got a code about the occupant retraintfault code anti lock brake u0184 dont know what it is somthing from the car to my transmission not working together cause this is the 2nd transmission with the same problem (except the codes)
I just got my 2016 mustang gt back from ford bc I’m having transmission issues, I was told it’s skipping fourth gear, basically when I get to 25-30 mph the rpm flares up and if I let off the gas and let the rpm drop a little then get back on it then it will shift and drive fine, but if I try to get up to speed quickly it just won’t shift it seems to me although I don’t hold the gas very long in that situation bc I don’t want shoot the rpm’s through the roof while not gaining speed. Any clue to what this might be?
So my 2012 chevy malibu ls 2.4, I drive every morning and it's good for a couple miles, all the gears shift and everything but after a little bit it'll only stay in 1st n 2nd gear???
When I shift gears from R to D and go to press on the gas I hear and feel a "Thud" noise. It only happens when I switch from R to D and not when I am driving. Even going into P causes that same noise on inclines and decline parking spaces :( I'm worried a mechanic is gonna lie about the repair cost or worse it's a transmission issue I won't be able to fix.
I Have a 2007 ES350 Lexus, when first used in the morning it will slip when it goes into 4 gear, after that it runs normal for the rest of the day. can it be a solenoid?
NEED HELP - I have a 2001 Olds Aurora, 4 litre ( V8 engine) that runs good, but just when I'm coming close to a dead stop, it"sometimes" bucks a couple times before idling down to low RPMS that it should have at stop position. It's like the engine wants to keep going, and doesn't realize, we need to stop. The engine doesn't rev high or anything, it just sort of bucks a couple times. This problem only happens intermittedly - not all the time. How can I fix this? Other than this problem, my transmission runs and shifts smoothly, and the speed of the car is not affected at all at normal driving speeds, but only when slowing down to come to a stop - may start to buck a bit before stopping. My car does not go into limp mode, but the Check Engine Light is on. BTW - Good video here, and does anyone have any suggestions ??
Anyone have knowledge on 1995 Nissan Ext cab v6 automatic transmission drives when cold. When warms up enough it acts like it’s in N and won’t go in gear at all. Messages are appreciated
So right now my ford fusion is having issues. While in drive it works fine but when I come to a complete stop and take off the car gets stuck in like a neutral statem. The RPMS build up but the car doesn't move. After a bit the car catches a gear and starts going
I have a 1990 300zx auto and my car will only go into first and second gear until I hit the overdrive button would this be a bad solenoid if the transmission is shot, I’m going to manual swap this thing
I have a 2002 Honda accord that I just bought from someone who had it sitting for like a year and some change the car doesn’t have a code wen I raned the obd2 scanner or anything but wen I go from park to drive or reverse it jerks forward doesn’t do it wen moving gear to neutral or park just drive or reverse and it also jerks wen coming to a stop I changed all the mounts and did the transmission change but still has the issues sometimes jerks wen going up to 1st and 2nd gear I would appreciate the help
My Hyundai 2016 when it's cold I can accelerate the car but when it warm it won't go anywhere. I changed the fluid but nothing happened. I think it might be a bad Solenoid but I need more help.
My 1990 k2500 4+4 5 speed shifter grommet or shifter rubber piece that goes around the shifter ball that goes into the transmission shift that makes it fit tight and shipped with like eight and up and I have tried everywhere to get one and I cannot and I have tried everything I could think of but for some reason it seems like it still don't want to s***
I have a 99 trans am it will not shift from 2nd to 3rd I changed filter an pan gasket an both shift solenoids,still same thing,it won’t shift into 3rd,should I replace all solenoids there is like 5 more around the valve body?
Our 2000 Chevy Monte Carlo everything is fine except sometimes I have to let up on the gas feed for it to transmission to change out into high I don't want the old cars that used to be a stopped up PVC valve but I don't know about this one if you have any comments let me know thank you
So I have a 2002 Silverado 1500 and when it shifts into second it’ll like jerk it I’ve been meaning to check the fluid but could the solenoid cause that??
I was driving all of a sudden car and trany not linked. Engine is good runs and all myb6 speed shifts good but car wont move I have a 2012 Honda civic si 6speed what could it be.
I have an 02 Ford Explorer Sport Trac I have spent $3,000 on the tranny already it will not go into reverse it wants to but it's like there's not enough pressure to Kick It In please help me I'm at my wits
What about if your driveing and the truck warms up and boom you push the gas and nothing happen but if you let it cool down it’s good for another ten mins or so before it heats up and stops again idk nvr had this happen before stupid 4l60
Wife said she couldn’t change gears from park on my truck (o fuck) checked the Linkage on the top nothing. When I looked at the link on the bottom there was a fucking rock in between shifting mechanism and the bell housing of the Tran stopping it from changing gears
I have a 1999 Subaru legacy and when I put it in drive it won’t move even after releasing the brakes I would have to step on the gas to start it to move but after it moves the others gear work fine it’s just that first gear any ideas?
hello i have a 2007 cadillac sts 6 cilinder. it starts well euns fine at the beginning but ,when i do a full stop the engine its running fine but the trsnsmission wont engage. car wont move it can easily be shifted but it wont do nothing unless i turned off the car wait about 2 minutes then restart and the transmission will work again until i make a full stop again. automatic transmission any ideas ?
Which solenoid though? A is the typical one I'm seeing in my research that is the one to change. I'm hoping ours is that problem . It's doing exactly what you described. Also it seems to do it more on the days where we run a lot. But when it does the tachometer shuts down and the speedometer.
Thank you for watching!
OBD2 Scanner: amzn.to/43UwyBg
Check out AllDatadiy repair manuals: www.gopjn.com/t/SENKTklLS01DSE1NS0lOQ0dKRk9LTw
Use code AD10VA for 15% off one-year subscriptions for any US Order
Check out my merch: easyautofix.creator-spring.com/
Have car-related questions? Check out JustAnswer! They have verified auto mechanics that are available as live help 24/7: justanswer.9pctbx.net/qnj74y
Buy a new shift solenoid: advanceautoparts.rt8x.net/rnPVQ3
Here are some of my favorite items that you might like:
Tools: amzn.to/3xNDb8g
Car Vacuum: amzn.to/3EjhPSJ
Cleaning Tools: amzn.to/3El7dCG
Water Repellency Wiper Blade: amzn.to/3utvK50
Cleaning Gel For Cars: amzn.to/36NIiMr
Portable Air Pump for Car Tires: amzn.to/3uBuPzA
Headlight Restoration Kit: amzn.to/3qDpOVH
Amp Jump Starter: amzn.to/3pMd0vx
I just got new tires and hit a big bump and only had 1st gear.replaced the plastic bushing and half washer on shift cable Then was driving about 30 mins ok then just had 1st gear all of a sudden. 2008 chyrsler Sebring convertible 3.5 never again.👎 sensor's then gone.😂
@ Easy Autofix Sir the car transmission is making whinning noise and delays in shifting gears, I checked for the fuel level is Ok, I checked for the oil still fresh not burned, I checked for any leaks no any leaks, I open the pan, but there were no any metal shavings on the magnets no any particles on the fluid, I decided to change the transmission filter, I checked and open the valve body no any clogs on the passages, I removed all solenoids I tested them all, and one was not working, I changed it with new one, I put back everything I test drive the vehicle no more whinning noise at all and gears are changing smoothly, but after two days as i drive reaching speed of 100 mph, the whinning noise started again, and the car struggles to exceed speed of 100mph, the RPM goes high and the speed is not achieved, I checked fluid level is OK. what can be the problem, and what can be done sir? Kindly help with ideas.
.
My O/D light keeps flashing on my ford f150 year 2000 and yes when I shift my gears on N/D/R etc it gives this jerk motion is that the solenoid or speed sensor?
What if I'm getting u0101? Says can't communicate with tcm
We’re all here hoping we don’t need a new transmission 😂
fucking true.
Facts!! 😂
Praying hard
Just replaced mine…issues mostly resolved but still having hard shifting from first to second lol so now I’m sure it’s a solenoid problem.
Just sold my 14 civic for a 98 accord and I really hope I don't need a new trans🥲
Taurus 02. Starting cold, It wont shift out of 1rst gear. After 5 minutes warming up, I can then shift freely all day until it cools. New Transmission fluid and filter.
Perfect thank you for your knowledge and experience
Would a bad Shift Solenoid be the cause of my 1995 Dodge Ram 1500 not moving out of park? I won't go frontward or backward. I bought brand new transmission fluid and oil and that didn't fix it... I was thinking along the lines of a linkage problem.
Yeah this comments totally off the subject here but I just got to say... you sound EXACTLY like the guest star that played a dude named CANVAS on Anger Management sitcom..😊
Recently had trans rebuilt in 2006 Dodge Mega cab, 3 new Solenoid's blew apart, before finding one that would hold up.
My nissan car when you drive cant exceed speed of 100, my transmission fluid is ok and on tge required level, but ecen if yiu press the gas pedal yo the bottom, doesnt exceed sich speed, what can be the problem? Kindly hep with ideas of how to fix.
my car shifts gears but revvs around 4-5k and doesn't shift until I let off my foot but then when I let go it stays om the same gear. any solutions?
So we all have dead cars rn 😂👏🏽
😫😂😂😂
Stoppppp 🤣🤣🤣their hibernating shhhh
Mine shifts hard when putting it in P, R AND DRIVE
😂😂😂😂
Bro!!!😂😂😂
How do I tell if it's just the solenoid switch, or the entire transmission? Because I hope it's the former because replacing just the solenoid would be much cheaper than replacing the whole tranny.
Good question, I hope someone answers it because I'm curious about that too
You need to replace the Sputnik vacuum valve under the transmission picke plate. Its easy to spot, because it's right behind the gear nook. Hope this helps👍
@@StevenSeagull6969 can you repeat that in laymen’s terms now?
Incredibly well made and great for those of us that are not mechanically inclined. Thank you
and thank you!
Limp mode ain’t to save you that’s for the car to save itself from further damage
Who’s having a remarkable day binge watching problems with transmission videos? Lol
My 2001 lesabre started with severe delayed shifting, first to second wasn't bad but second to third would slam into gear, I did some research and found that this was a known problem on some lesabre models. The temporary fix if you can call it that is to shut the car off which resets the module, leave it off for a couple of minutes then it shifts normally again until it does it again, sometimes it lasts for a bit but then the problem comes back, with close to 300,000 miles it was time to replace all five solonoids. I purchased all five as a package deal off eBay, all OEM parts, the first thing is to prepare the patient by raising the rear and front of the car, I used ramps on the rear and jacked up the front as high as I could because you need to lower the subframe and remove the strut cv axle and everything necessary to gain access to the side cover of the transmission. Remove the cover and it's relatively easy after that except for one thing, the wiring harness that connects the solonoids together, from being heated and cooled a million times the clips that hold the connectors are more brittle than Bob Barkers back, one broke on me and there's no real way to secure it thst I felt confident with. I went to my local Buick dealer and go my surprise they still made the harness, and it could be mine for the poultry sum of 350.00 dollars. I told him I'd let him know, went home and low and behold I found one on eBay for 25 bucks, the only thing was that now I had to wait almost a week with the car in pieces taking up my driveway. I received the part put everything back together and prayed. That was about five years ago and she's been shifting perfect ever since, all told parts, the side cover gasket was the most, second to the solonoids at 55 bucks, all five solonoids were 75 from eBay,,the whole job was around maybe 175 including trans fluid, you loss a lot from the side cover, I also removed and replaced the trans filter while I was at it. I've been working on cars for almost 40 years now, I wouldn't recommend doing if yourself for a beginner but then again, everybody has to start somewhere, power tools aren't necessary but they make the job to faster, with hand tools it's a lot of nuts and bolts to remove.
appreciate your comments....Have an05 LeSabre. Sometimes rough bump after initial shift into drive. Five solenoids?
Saw a separate reference about 4 solenoids..wonder what the 5th one is. Could u mention the specific seller on Ebay?
Thanks for t your excellent post..jP
What state you located?
I have a 2002 lexus that when I get to 2000 rpms it’s takes a good amount more pressure than usual to hit 3000, could I be needing the same fix ?
How you paid for all 5 ?
@@vonstew3314 The same way you always pay for purchases on eBay or any online retailer.
So what does it mean if it shifts from 1 2 3 but when I get into fourth it just revs when I press the gas
Thank you so much young man. I have a 2016 Ford Focus and had the clutch replaced and my car is still experiencing these symptoms and by watching your video I realized my car is going into limp mode. The dealership will not fix anything else other than the clutch that’s under warranty unless I cough up some more money. Thank you!
I clogged catalytic converter also creates similar symptoms.
@@precisiont5188 Unfortunately, it’s not that! Ford told me it’s the master clutch just some more bullshit.
Get rid of that car! The Focuses have trans n clutch issues! I had one and I had gotten the Clutch replaced like 4 times. Recall on it.
i had a 2016 had clutches replaced 4 times then traded it in
@@tattboinc Thanks for your reply! My car is FINALLY fixed!
could you make a video on how to change or clean the shift solenoid ?
that's a good one .
With the tran fluid pan removed, you simply pull it off, it clicks on like any wire connector. Looking is knowing.
Before running out and buying those solenoids try replacing the Transmission Control Module that is located inside the air filter box, (Chevy Impala) no tools required and it fixed my problem. They will run you about $20 at the salvage yard, fault P0700.! It takes 5 minutes to replace! You're Welcome
Thanks. Is your impala a 2010?
@@jaredpatterson1701 Mine is a 2006 but it is the same for all Impala's that use a TCM
My 1995 mitsubishi super saloon v3000 wont do first gear just starts to have power around 60mph help me whats my problem
@@ythaks267 Your problem is that you bought an import, get rid of it and buy a newer vehicle, A GM product made in the USA is a good choice
@@markolsen7438 that depends.
An older GM sure,a new one no thank you.
Buy a toyota,with proper maintenance,will last forever.
Fuck made in America bullshit pride
What if it’s holding gears before shifting in my case it’s 2-3 gear shifting late. replaced the fluid still does it
Did you figure it out
@@Francofit nope still driving it like this feels like it’s getting worse haha I’ll buy a junkyard trans and swap the parts the valve body and solenoids. If that doesn’t work I’m screwed lol but it should
@@NeverFollowTheCrowd damn, my car does the same but it’s 3-4 and it’s a 4 speed auto. I guess I have to manual swap it then
Almost everyone watching has atleast one thing in common… our trans are shifting like shit 😂
Yep, wont shift into 3rd gear
Right on brother ' you've given me hope. 👍 As I drive my 2009 F-150 4×4, the automatic transmission will shift into first gear smoothly, it shifts into second smoothly, then it clunks sharply into third gear at around 35 to 40 mph. Viewing your video, I'm hoping it is something as simple as a solenoide. Thanks again 👍🙏
Any luck with this video my f150 is doing similar things you speak of when it goes to third gear. Please let me know thank you
@@vind357 Lukas transmission fluid can help with hard shifting transmission
Did this fix ur issue
What's the word?
@@memphistiger4647 it's possible the OP will totally fk up the solenoid replacement if he attempts himself
I love the break down how your explain what each action and reaction is.
Those are exactly the symptoms my truck is having 😢 better than needing a new transmission by far😅
Great explanation of what the automatic transmission parts do.
How much does it cost to fix this item at a dealership? I'm a widow, I can't do this myself. I have job interviews to get to before I can afford to fix it, or pay rent.
Thank you for the video. It explains what the truck just did.
Take care, stay safe, have a nice day.
👵✌️🖖
The dealership robbed u didnt they?
Often u can do this work urself for under $100.
Toyota dealership tried to say my transmission needs to be replaced.
I said no thanks.......
Just change the fluid, strainer, gaskets and shift solenoid.
260 k mile tundra
Guess what
Runs like I just drove it off the showroom floor!🙏✌
Good shit exactly my symptoms in my Cadillac limp mode limited speed and shift delay also stuck in 2nd/3rd gear
Thanks, is it possible to get this kind of issue without having the check engine lights on and detected on the scanner?
My car has similar symptoms but nothing being detected when it scanned
I believe so because I have these symptoms and only traction light on
@@cruddy00tv62 thanks, was the issue with your car fixed after the solenoids replacement?
@@anggadwikara6881 I didn’t replace them because of the fact of not getting codes but I researched a lot can’t find the main video I seen but I’ll find it for you but this may help wanted to try today but it started to rain I will update you when I put the ground wire on to see if it works
@@anggadwikara6881 ua-cam.com/video/EzQZbGp14ro/v-deo.html
@@cruddy00tv62 please update later sir 🙏
2006 Toyota tundra seloinde A
Where's located?
When mine shifts from 2nd to 3rd, it just revs up like it went into neutral.
mine is doing the same shit. it does it when its cold. but after it warms up, its fine. its just on cold starts that this happens
Same here men
Mine shifts fine till 3rd gear then it just revs high I Have all my other gears still any suggestions?
I'm thinking it's one of the solenoids inside the pan. Probably worth it to just replace them all vs dropping the pan multiple times
@@laylowk1426 Did u find out the issue
Put the playback speed to 1.25 😂
This made it feel normal i thought i was watching the video in slow motion 😅
😂
😂😂😂I thought it was on 0.5x
Do you always get a code for a shift solenoid? My trans stays stuck in a gear. It doesn't act like a slipping transmission to me. It's a 2003 Ford F-250 with a 6.0
Thank you so much. Explanation helped me more the second day I watched it!
Thank You; just saved me from a scam rebuild; for real !!!
I have a 6l80e and 2-3 slips sometimes but smooth on highway or if I’m giving it enough gas. Changed fluid and it’s still the same not better or worse. Trans never overheats. Always stays 140-180
See if cleaning or replacing your MAF helps. Trying that now as soon as my maf comes in the mail
@@oleyeller3256 did that help?
@@smashadams85100 nah not in my case unfortunately. Now im waiting to change trans fluid and adding a bottle of that seafoam transtune and see of that helps. Adding some tomy existing fluid seemed to have helped some
@@oleyeller3256 damn.
I’m currently having this problem with the same transmission, my fluid was burned and it wasn’t much of it in there at all. I can’t find any solenoids and I’m hoping to avoid buying the entire valve body. Have you found a fix yet?
2 days ago my older 2000 F250 (only 136,000 miles on it) went "clunk" and the whole truck lurched - then it was like it was stuck in a low gear. I still had to drive a mile home - it did this 3 more times, lurching like it was about to stop, stuck in a low gear and higher rpm's - but it got me and my groceries home - and I haven't touched it since. Least now I know what to tell the mechanic. Thanks.
How you solved? I have same problem
Damn bro. You nail every fucking symptoms my truck has. Apreciated
Exactly having this same issue, do better GM
Great video, I have a 2000 JEEP WJ 4.7 and it started shifting hard from 1-2 and the kickdown from 4 to 2nd is really hard, do you have any idea on were to start? Cheers man!
Coworker has the same issue.
@@e.l.9589 It rusted out to be a disk plate set and needs replacing. The OEM diagnostic tool made an adaptation for the gearbox and now it works smoothly. The guy told me that would last 100-200km but I did 700km and still shifts perfectly smooth.
Cheers
@@itasev Nice, his downshifts on the freeway to high rpm but if he restarts it then it drives normal again.
Really an explanatory video with detail , I’m experiencing a clunk noise almost 2 second after coming to a full stop , could it be torque converter ?
i had that on my old ford taurus, i think it was a trans mount
Thank you! Those are the symptoms my car is experiencing!!
Awesome,Thanks for watching!
Did changing them help?
I have the same problem but no check engine? Any help
sometimes my car could not shift gear the engine just revs and that is it.so I went to change transmission oil it was black.put new one and went to a shop that uses a special machine that is for changing transmission oil .believe it or not at my last transmission oil the people told me they do notnhave the proper equipment sp they could oybtake out only 40% old oil.noq they took 90%of the old oil.
now the car shifts way better than before and so far does not stuck and does thebold problem but I still think new solenoids would help.
@@EPICSOUNDTRAXthey did a complete flush vs a drain and fill. Some people recommend against it as it can potentially cause more damage
I did like the good examples. I hope to
Hear more. Thanks. Tony.
I have a 2010 nissan rogue cvt level is good but 80% of the time when shifting from P to R or D it shifts pretty hard, any idea if a bad valve body could be the culprit? (Mounts are good)
First problem is it's a cvt transmission. DOA
Thank you for the information. Driving home last night (any where from 40 - 70 mph) with no stops, until in town, my 2009 Chrysler Town & Country stalled. Started up in neutral, shift to Drive, and it stalled again. Kept trying, was able to get it going and found it would run/drive using manual D1, D2, etc. Works okay in reverse. No engine light though? Prior to this stalling problem I have noticed at stop lights, the engine seems to idle at higher RPM. But not all the time. Taking it to the transmission shop for professional diagnosis. Have a great Labor Day weekend!
I know this is an old comment but did you find out what the problem was?
My 2000 ford expedition 4.6L V8 Triton XLT 4 wheel drive is doing similar, and there is no check engine light, but my ABS light is on.
My vehicle won't even go in reverse or allow me to shift to Park. I only can drive if I put the gear in 2.😬
I was told it was my Shift Solenoid that needs replacing.🤔
@@flowersfam3462Had a 2,000 bid to open it up and work on it. But the mechanic did not really want to do it. The other transmission shop would not even consider checking the solenoid. So I chose to replace the transmission (they gave me a 3 year warranty on the new one).
Three days after it was fixed my battery died.
The one fella told me his wife's truck was shifting bad and it was because the battery was going bad! Some kind of electronic issue! I'm putting that fact out of my mind to not second guess my purchase!
@@kathysaul9645 Thanks for the response.
Hello everyone. I'm wondering if you could help me to help my dad. His work van is a 2001 Econoline2001 e350 it won't go into drive it only will go into neutral Park and reverse. He took it to a shop and paid $200 just for them to look at it and they told him he needed a new transmission. The person that sold it to him told him to never let anybody tell him it was the transmission if that happened that it was the solenoids. The linkage being loose. Does anybody know anything about this at all I've looked everywhere and I can't seem to find anything
Check the transmission control module. It might have got wet .
Thx so much 10 years just needed to know this , aww thx so much !!!
If my pressure control solenoid is bad do I have to get another transmission rebuild?or can I just replace the pressure control solenoid?
You need a new car bro, if one of those is bad, it means its over for your car, can't be replaced, they don't make those and if they did make em, you cant remove your current one as its permanently welded with gorilla glue ultra super duper strength Silverback edition.
@@dannydee9919 that's not true bro and that depends on the make n model for mustangs yes they makes em and its right underneath the tranny pan
@@dannydee9919 and why would you say they need a new car when some shops may charge $1000 to rebuild transmission don't give false information bro
@@bosspranks8349 i just pulled my 2nd shift solenoid out of it with no problem with being welded in by the motors heat like some would think. And my wifes car has high milage lol. but i still replaced mine but its doing the same and not shifting.
@@huggdeeznutz on a mustang?
2021 Hyundai Tuscon SEL 145,000 miles between 40-55 mph there is a slight shimmy or shutter for 3-4 seconds then back to normal no service engine lighten back to normal no service engine light
Another common symptom of a bad solenoid is rough shifting.
Had my 460le rebuilt with monster trans kit, the cooler installed line broke and I got it towed and replaced asap, 1 week later I get a CEL for stuck solenoid open. Could it be dirty fluid or something worse? Drives and shifts fine although I parked it since running this code. Only thing noticed is my 2nd gear shift kit isn't thumping into 2nd like it used before changing cooler and fluid
A friend's Chevrolet truck went into "limp mode" and wouldn't change into 3rd gear. He fired the parts cannon and had spent all kinds of $$ trying to figure out what it was. I came over while he and his "automotive tech" neighbor were standing around the truck scratching their heads. Lol when I asked if he tried replacing the transmission shift solenoid his "tech" buddy immediately blurted out "thanks but it wouldn't shift at all if it was bad."
Long story short.... It was the solenoid. I think he'd spend a couple hundred bucks already. Lol $18 for the solenoid, and around $40 bucks for pan gasket and new ATF was all he really needed.
which one of the 5?
Changed my whole valve body out and it shifts out good but when I stop it’s like I’m stuck in a hole and then when I accelerate to move forward it kicks back into gear and goes. Does the same when I’m reversing. Stalls for a minute and then I press the gas it bucks and then starts to move. Other than that it shifts fine.
This is a long shot hoping someone will chime in with some advice. I just had my transmission rebuild on a 2015 gmc Sierra 5.3. - I feel like the mechanic has done something incorrect. he has had it for a month now. has retired it to me a few times and the truck is not shifting correct. once up to full operating temp it will slip badly going into 2nd. Instead of shifting it will go into neutral and the revs will go up fast until I let off the gas , then it will usually clunk into gear , it goes through all the other gears fairly normally. he is claiming that the truck has to go thru a "learn cycle" than can take multiple days of driving it with these symptoms. sometimes it will just stick in second until oi come to a complete stop then it will go back to normal for a little while. it is also leaking a considerable amount of fluid, took it back twice for just the fluid leak and he keeps saying its fixed but then I take it home and its leaking. he said "sometimes it will leak a little at first"....none of this seems correct. the truck only has 80,000 miles on it and I do not think it even needed a transmission , the whining noise it was making that brought me in the begin with has not been resolved with the rebuild. this shop is where my warranty required me to take it and has very good reviews so I felt like it was a reputable shop. Is it true that a 2015 gmc transmission requires a re-learn period like this and do these sound like normal symptoms of that? I paid a lot of money for this truck and feel like this guy may have destroyed it. the amount of time it is taking is also excessive seeming to me. PS there is no check engine light or trans light coming on and this is why he says nothing is wrong. he has finally agreed it shouldn't be leaking trans fluid so it is back there again for that to be fixed.
Say what🤔
Were made in HIS image. HE made us with the power of free choice
A good prayer:
I'm a sinner JESUS please forgive me for all my sins I know you shed your Blood for me on the cross at Calvary. Thank you JESUS for my salvation and for shedding they Blood for me. I love you JESUS.
Romans 10:5/10 ct...❤️k
JESUSisLord!Amen...
Amen..
If you'd like to call someone who cares
83
For
Truth.
bc you don't know when you'll die?
.y r u hesitant. . .
I know this video is a few years old I don't know if you'll get this message or not I have a 2009 Chevy Malibu 2.4 4 speed no engine light comes on but it will not shift into overdrive or shift out of 3rd gear I'm driving 70 mph and the RPMs are like 4,000 when it should be like 25 any suggestions transmission fluid is good I'm thinking a solenoid but why would there not be a engine code
Great video thank u!! I drive a 08 Lexus IS250. When slowing down and almost about to come to a complete stop I feel a slight bump. Do you know what that can be related to?? I have no check engine light. And I just got the car so I'm not sure if the training fluid or filters was ever change.
i just got a ls400 like last week and it’s doing the same thing💀
@@2righteous I got an update. So I did an engine oil flush using motor medic. I then change my engine oil, filter, and spark plugs, and did a full throttle buddy cleaning down to removing the intake manifold and soaking the intake passages which were full of carbon and slosh. I used seafoam for that. Additionally, I change my front and rear brakes complete with new rotors. Miraculously that surge or bump I was feeling when coming to a complete stop has now disappeared. I'm guessing it had something to do with the carbon cleaning I did and not at all transmission related. What ever it was I no longer have that issue.🤗
I have 2005 ford focus, no reverse or barely can go forward! When in N I cannot push it backwards, but can push forwards. I am not getting any codes? Any information? Could it still be a solenoid?
My brother has a 16 highcountry with the 5.3 9l80 I believe and sometimes while driving it will go out of overdrive and run at 3000rpm. If he turns the truck off and then on again, it works fine until he hits a bump. We cant figure out what it is and the mechanic is trying to sell him a new transmission! Any help is appreciated
Is it possible to make the TV cable adjustment too many times? If so, what are the repercussions of doing that? I've been having issues, for about 6 months now, with my 94 Jeep XJ automatic shifting either too quick or too late, very erratic overall. I've replaced the TPS and have done this adjustment probably 20-25 times over the coarse of the last 6 mos. Yesterday, it started to not shift at all on the highway. I would press the gas and the RPMs would go up over 3000, but it would not accelerate and I had to coast it into a gas station. Went out and made the TV cable adjustment and then would crank, but not start. Repeated the adjustment 5-6 times and still wouldn't start. Unplugged the TPS and it started right up. Attempted to drive it the 5 miles home, with the TPS unplugged, but the same issue came up with it not shifting or accelerating. Is this what they call "limp mode"? Anyway, I pull over and plug the TPS back and try to start it and this time it started and mysteriously drove and shifted much better, although still not perfectly. Should I be looking at something in the transmission itself at this point? It's full of fluid and it's the stock AW4 tranny. Does any of this sound related to a neutral safety switch problem at all? Thanks for any help anyone can offer.
Hi, my Chevy Blazer 3.6 2020 has vibration, i think its from transmission, i shifted gearbox in L, when shifting from manually gear box cannot shift in 3 gear. can you advice me what to do?
Ok in my 05 trailblazer there is 2 solenoid 1-2 2-3 or 3-4 not sure but there's 2 my truck shifts 1-2 but no 3-4 , my question is is which solenoid is the bad one? How do I tell the 1-2 from the 3-4? They look exactly the same?
I have a 2015 Hyundai Santa Fe 2.4L AWD. Transmission shift out of second in Automatic but I can shift it manually bye moving the shift lever to the right. Need help.
Mines p0773 and still runs fine.. I got it back from a mechanic with this code and when I took it to him I had no codes or CEL on. He replaced my valve cover gasket and spark plugs. Could this cause this solenoid to malfunction or something??
Am using 2004 honda Accord 3.0 v6
My problem is whn i kick full acceleration rip goes high and rpm is cutting off.. not shifting to next gear .but when i drive normally all gears are shifting normal.. only in full throttle rpm is cutting and not shifting anyone knw why?
So basically if this is bad & I take it to a transmission shop…There gonna say o sorry sir but it’s gonna be 2500 to fix your transmission? SMH…People LEARN how to fix your own 💩
Well I just went ahead and added 3 bottles of Lucas transmission fluid 😉🤦🤷♂️💩😆🤣☠️☠️☠️#FullSend #DoIt4Dale
Hi everyone! Im about to work on a Volvo c30 transmission that is not engaging 1st and 3rd gears just 2nd and 4th anyone knows what could be causing the problem!? Thank you! I suspect that could be a bad solenoid what you guys think!?
Hi! How are you? I have a problem with my ram 5.7 2016 with automatic gearbox. The problem is that when the truck need to put the 5th gear the revolutions going up but the gear is not into. Is like you press the clutch in a manual car and accelerate. I changed the valves box and also the solenoides for the another model but the same piece, because my ram has an grey connector and I puted a green one. Thanks so much 😁
I have a 1995 Silverado 5.7L 4x4.... Put in gear, and it barely moves just high rpms and takes forever to get to 30mph then boom we are off to the races runs like a champ, what's my issue?
This was pretty good. Straight forward!!! Another straight forward idea is, don’t buy US trucks. They’re ALL garbage. Buy Toyotas. Hell even Nissans are way better with less headaches
My car first symptom was the check transmission light that came on with a flashing drive gear light while I was going 60 the speed limit on the freeway and the car switching to lymph mode as soon as the rpm arrow went above number 3 and got stuck there. The car started driving at least 40 mph while the speedometer still said I was going 60. I parked the car right on the side of the highway to let it cool off. Fast forward to 20 minutes later, The car was back to driving normally again. Following that about a couple of weeks later, I noticed weird gear shift delays regardless what gear I switched to unless I put it into park and following that, It makes a clunk noise coming directly from the transmission when it finally does switch.
When I accelerate and reach close to 20 mph, A typical car with an automatic transmission switches to higher gears but mine gets stuck in gear and the engine starts revving harder and it jerks back to its appropriate gear. Upon inspection I did notice that the transmission is very low on fluid and the fluid is almost black. I took my car to the mechanic for a diagnostic and a fluid with filter and gasket change where he told me that the transmission needs to be replaced and upon further questioning, He told me that there’s no point in changing the fluid because the transmission is basically bare medal rubbing debris and that it would make the transmission run worse. It’s been about a month now and the car runs basically the same as it did when I visited the mechanic with no transmission failure and I’m thinking about bringing it to another mechanic for a second opinion when I have money. I would be more then glad to hear your guy’s opinions and suggestions if any as well. I’m very hopeful that the first mechanic was wrong.
I have these symptoms with my Honda Civic LX
The mechanic says it's code is PO730. Would this video be for that code as well??
Good video.....my chrysler 300 2006 touring ...i can put in R and D when i drive it i feel no change in gears engine feel like it losing power hear a strange knocking in engine the knock dont come until about 4 or 5 mins of engine on cut i car off then back on the knock gone for awhile then come back got a code about the occupant retraintfault code anti lock brake u0184 dont know what it is somthing from the car to my transmission not working together cause this is the 2nd transmission with the same problem (except the codes)
I just got my 2016 mustang gt back from ford bc I’m having transmission issues, I was told it’s skipping fourth gear, basically when I get to 25-30 mph the rpm flares up and if I let off the gas and let the rpm drop a little then get back on it then it will shift and drive fine, but if I try to get up to speed quickly it just won’t shift it seems to me although I don’t hold the gas very long in that situation bc I don’t want shoot the rpm’s through the roof while not gaining speed. Any clue to what this might be?
So my 2012 chevy malibu ls 2.4, I drive every morning and it's good for a couple miles, all the gears shift and everything but after a little bit it'll only stay in 1st n 2nd gear???
When I shift gears from R to D and go to press on the gas I hear and feel a "Thud" noise. It only happens when I switch from R to D and not when I am driving. Even going into P causes that same noise on inclines and decline parking spaces :( I'm worried a mechanic is gonna lie about the repair cost or worse it's a transmission issue I won't be able to fix.
I Have a 2007 ES350 Lexus, when first used in the morning it will slip when it goes into 4 gear, after that it runs normal for the rest of the day. can it be a solenoid?
My 2011 Nissan Altima 2.5S is throwing code P0746 line pressure solenoid A closed. Showing all symptoms in video.
NEED HELP - I have a 2001 Olds Aurora, 4 litre ( V8 engine) that runs good,
but just when I'm coming close to a dead stop, it"sometimes" bucks a couple
times before idling down to low RPMS that it should have at stop position.
It's like the engine wants to keep going, and doesn't realize, we need to stop.
The engine doesn't rev high or anything, it just sort of bucks a couple times.
This problem only happens intermittedly - not all the time. How can I fix this?
Other than this problem, my transmission runs and shifts smoothly, and the
speed of the car is not affected at all at normal driving speeds, but only when
slowing down to come to a stop - may start to buck a bit before stopping. My
car does not go into limp mode, but the Check Engine Light is on.
BTW - Good video here, and does anyone have any suggestions ??
Vacuum lines
Anyone have knowledge on 1995 Nissan Ext cab v6 automatic transmission drives when cold. When warms up enough it acts like it’s in N and won’t go in gear at all. Messages are appreciated
So right now my ford fusion is having issues. While in drive it works fine but when I come to a complete stop and take off the car gets stuck in like a neutral statem. The RPMS build up but the car doesn't move. After a bit the car catches a gear and starts going
EasyAutoFix : THANK YOU SIR . PERFECT DETAILS HERE . NOW TO GO CHECK MY ONE EYE COUSINS TRANY. BEST BLESSINGS SIR . U.S.A.
I have a 1990 300zx auto and my car will only go into first and second gear until I hit the overdrive button would this be a bad solenoid if the transmission is shot, I’m going to manual swap this thing
I have a 2002 Honda accord that I just bought from someone who had it sitting for like a year and some change the car doesn’t have a code wen I raned the obd2 scanner or anything but wen I go from park to drive or reverse it jerks forward doesn’t do it wen moving gear to neutral or park just drive or reverse and it also jerks wen coming to a stop I changed all the mounts and did the transmission change but still has the issues sometimes jerks wen going up to 1st and 2nd gear I would appreciate the help
My Hyundai 2016 when it's cold I can accelerate the car but when it warm it won't go anywhere. I changed the fluid but nothing happened. I think it might be a bad Solenoid but I need more help.
My 1990 k2500 4+4 5 speed shifter grommet or shifter rubber piece that goes around the shifter ball that goes into the transmission shift that makes it fit tight and shipped with like eight and up and I have tried everywhere to get one and I cannot and I have tried everything I could think of but for some reason it seems like it still don't want to s***
I have a 99 trans am it will not shift from 2nd to 3rd I changed filter an pan gasket an both shift solenoids,still same thing,it won’t shift into 3rd,should I replace all solenoids there is like 5 more around the valve body?
Our 2000 Chevy Monte Carlo everything is fine except sometimes I have to let up on the gas feed for it to transmission to change out into high I don't want the old cars that used to be a stopped up PVC valve but I don't know about this one if you have any comments let me know thank you
So I have a 2002 Silverado 1500 and when it shifts into second it’ll like jerk it I’ve been meaning to check the fluid but could the solenoid cause that??
I was driving all of a sudden car and trany not linked. Engine is good runs and all myb6 speed shifts good but car wont move I have a 2012 Honda civic si 6speed what could it be.
I have an 02 Ford Explorer Sport Trac I have spent $3,000 on the tranny already it will not go into reverse it wants to but it's like there's not enough pressure to Kick It In please help me I'm at my wits
What about if your driveing and the truck warms up and boom you push the gas and nothing happen but if you let it cool down it’s good for another ten mins or so before it heats up and stops again idk nvr had this happen before stupid 4l60
My 2002 Buick LeSabre won't stop when I put it in park... breaks work fine in other gears..but the car won't stop in park??
Can a bad solenoid also stop the car from moving on driving or reverse, it won't move at all on any gears? Thanks
Yes
Will I be able to go in reverse if solenoids messed up? The suburban won't go in forward gears but will go in reverse. Could that be the solenoids?
hey did you get it fix
Wife said she couldn’t change gears from park on my truck (o fuck) checked the Linkage on the top nothing. When I looked at the link on the bottom there was a fucking rock in between shifting mechanism and the bell housing of the Tran stopping it from changing gears
Ford F-250 06 diagnostic shift sensor supposedly the mechanic replaced it it still goes into toe Hall mode and it just keeps driving crappy
I have a 1999 Subaru legacy and when I put it in drive it won’t move even after releasing the brakes I would have to step on the gas to start it to move but after it moves the others gear work fine it’s just that first gear any ideas?
hello i have a 2007 cadillac sts 6 cilinder. it starts well euns fine at the beginning but ,when i do a full stop the engine its running fine but the trsnsmission wont engage. car wont move it can easily be shifted but it wont do nothing unless i turned off the car wait about 2 minutes then restart and the transmission will work again until i make a full stop again. automatic transmission any ideas ?
Which solenoid though? A is the typical one I'm seeing in my research that is the one to change.
I'm hoping ours is that problem . It's doing exactly what you described. Also it seems to do it more on the days where we run a lot. But when it does the tachometer shuts down and the speedometer.