Це відео не доступне.
Перепрошуємо.
How To Fix A Leaky Delta Two Handle Faucet
Вставка
- Опубліковано 17 сер 2024
- Learn how to replace a leaky Delta Faucet. Most faucets begin leaking around the cartridge inside the valve body when the seals get worn or the cartridge itself wears out. The cartridge is designed to be easily replaced so you do not need to replace the whole faucet.
This video shows you how to replace a valve cartridge for a leaky two handle Delta faucet. The steps to replace this valve are similar to most two handle faucets.
Learn more about plumbing by visiting our website at www.icreatables...
Check out our other projects on our website at: www.icreatable...
For more Project Videos, check out our UA-cam Channel: / icreatablestv
Subscribe to my channel: www.youtube.com...
WARNING: These projects can be dangerous, posing risks of personal injury, or property damage, and in some cases, death. There may be the possibly other risks of which I am not fully aware. Use of video content and or website information is at your own risk.
Thanks for watching!
For me, the ideas in ua-cam.com/users/postUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.
And many years later, you are still helping people with this video! Exactly what I needed, and a quick and inexpensive DIY. Thank you!
A good video except for a couple of oversights. First, if the valve has been in place for a few years, it's probably encrusted in place and needs pulling out by grasping the stem with pliers and pulling upward. Second, close the drain in the sink before emptying the bag containing the new cartridge, because the plastic "stop" is not attached to anything and will probably fall out of the cartridge and may go down the drain (the stop works by running into a coupe of ridges built into the interior of the sink handle, so it may seem useless till the handle is in place). Third, the little spring goes big-end-first into the opening at the bottom of socket, and the little black plastic tube fits over the spring. Fourth, I believe the "key" is the tab in the white plastic portion of the cartridge that fits into a notch on the socket that receives the cartridge. It slides into the notch only about halfway, so don't be hammering on the cartridge to get it all the way in.
Helpful video and very well done, thanks. A heads up - to fix a leaky handle base, as seen in this video, all that really needs to be replaced, rather than the $15 cartridge assembly, is the 2 O-rings in the original cartride. Small o-ring #83 for the stem and larger o-ring #67 for the body. About $2.50 each for a 10 pack. Some plumbers grease is always useful for smooth re-assembly. Replacing the valve seat cup and spring at the same time is a good idea too ($3 - $4).
Kermit Kinne Great info. Thanks for your comment.
Door bell
Home Depot: Danco #67 O Rings and Delta RP77737G for the seat and spring fixed it right up.
Hey it worked! Thanks - just saved me a bunch of money and headaches!
Thanks, very useful. To mention my delta faucet set screw was 3/32". Close sink drain or put paper towel over drain in case you drop a part. For me the flat part needed to be pointed left away from faucet and was in closed position I think.
Perfectly concise and helpful. Thank you for making my life less stressful!
Thanks for watching and commenting!
Yes, following your video did the trick! I have the same faucet and was working on it for an hour and a half before I found your video. THANK YOU!!
Sweet!
This is the best DIY I found. Thankfully it shows each step & assembly for geniuses like me who forgoit to pay attention when disassembling. Also appreciated that there wasn't a long intro full of irrelevant information.
+Sybil Disobedience Thanks for watching
^^ Everything that she said ^^
I bought a Danco 3S-9H/C to repair a dripping Delta two handle faucet on the hot side. Couldn't figure out how to make the hot stem handle work in the right direction until I noticed the Danco stem separates into two large parts. Push down on the top and separate the two parts, adjust one by 180 degrees, then you can get the stops which may also be called shoulders to line up correctly with your handle. This was not in any instructions on the box. this stem also does not have removable shoulders like my original. (should have searched for an more expensive original)
If both your handles rotate the same direction you won't have an issue, but on my two handle Delta, the hot and cold water handles rotate in opposite directions to turn on the water. Counterclockwise to turn on hot, CW for the other handle for cold.
BTW, I didn't review the entire excellent video, so I hope this doesn't repeat anything in this solid video.
G Sm this makes this vid complete, for those that do the reading, anyway. Cheers!
Great vid! Super helpful, helped me fix my leaky handle!
Very helpful tutorial !! Thank you !!
Thx for the helpful video
God bless
Very helpful thank
Clear and Concise. Thanks!
Thanks for watching and commenting!
This was explained perfectly thanks!
Thank you. I could remember the spring, but not where it was.
Bizarre that Delta doesn't sell spring/seat gasket/gasket on cartridge, as a set by default.
Nice video; thanks. Unfortunately my professional plumber is unable to solve the problem after installing a new cartridge (RP24096) complete with 1/4 turn stop (RP2409) and new seat/spring RP4993. When installed the same direction as it was prior to removing the old cartridge the water does not turn off. However, it does turn off when rotated 180degrees ... but of course that means the handle is facing backwards . Any advice ?
It sounds like it is installed 180 deg off. I would take it off and double check.
Same thing happened after a professional plumber “fixed” it for me. $150.00 plumber fee on top of that.
Had the same issue and just (mostly) fixed it. The top of the valve will rotate 90 degrees so that it faces the same direction as the original and then you turn the metal piece in the center so that the flat slot is facing the right way and lines up with the insides of the handle. Mine now faces the right way but there's not a lot between having it turned off all the way and it starting to drip. I solved the problem but wish there were 15-20 degrees of rotation before it starts to drip. Will call Delta tomorrow for instructions.
thanks. let me know if Delta has any advice that works
Thanks dad !
The spring fell deep into the shank. Had to fish it out with a modified coat hanger. Isnt it supposed to stay in place. Any ideas on why it fell to the bottom?
my faucet does not have a bonnet nut. does that mean my cartridge is built in to the faucet and is not replaceable? Thank you for your help and expertise!
Any tips for loosening the faucet handles? Takes a good amount of force to turn mine (same model) and my kids therefore have trouble shutting it off all the way
If it's not related to corrosion in the valve, you might have an o-ring inside the cartridge that's bloated or too large.
Any thoughts on removing a a corroded bonnet nut? I'm attempting to replace a bad cartridge on a delta faucet on a roman faucet with no access to the underside.. Afraid of twisting off the supply lines.
It’s not the cartridge that goes bad. Typically the plastic cartridge is fine, just replace the o-ring around the cartridge and the seat washer and spring and save $20 per handle
No mess to revive the set screw. Just loosen it and the handle will pull off
Porque no sierra el agua
What is the name of the faucet? This is the exact faucet I have
Porque no podemos
Do you know what size Allen wrench is used to remove top housing? None of mine fit!
If i remember correctly they are metric.
iCreatables Thank you! I bought the set you were using. Hoping I bought the right cartridge!
Can somebody please help? I've gotten to the 1:40 mark with NO problem.
BUT - the cartridge simply WILL NOT come up! No matter how hard I lift and jiggle, it's not coming up.
Any idea why?
Thanks in advance.
What is the small white plastic piece that comes in the stem package for?
+deb mohler It is a lock key. It stops the faucet handle from spinning a full 360 deg.
3/32
I just replaced mine and it still leaks. New springs, seats and stem. It’s leaking from faucet now…
How tight to you tighten bonnet nut? Did I over tighten?
Sometimes the oring gets unseated when you push it in and causes leaks.
What if it is leaking from the spout? Whats the ususl problem? And what if the bonnet nut holding the cartridge seems stripped? Teflon tape?
ltetobago A bad cartridge would be my first guess. The cartridge and its o-rings are what stops the water. If your bonnet nut is stripped it may not be holding the cartridge and whole assembly tight so that could also cause a leak.
iCreatables thanks I fixed it, I changed the seat and rings? Put in the new cartridge (because i had it), 7 wraps of teflon tape and its all set..i ordered a new bonnet nut from deltas site..they were discontinued at home depot...thanks again!!
It has std take it to the doctor
What foods for diabetics?
How to remove a leaking hose from a delta kitchen faucet
What is the key ? I cant see anything like a key what do you mean?
The key is the piece of plastic that sticks off the side that does not allow the cartridge to turn past the point that the key hits.
Yeah not that simple. I replaced the cold water side and when I turned it on the hot side started spilling out
Toothpaste splatter removal would have helped some too.
Looks a little like hard water stains.
Wonder if you could re-record the installation step a little faster so it's *completely* incomprehensible. SMH.