Live data is missing some properties like temp, hum etc current observation data in vantage pro 2 wireless console after data logger firmware update. Is there any way to revert back to 1.1.1
Does it matter which way the anemometer's arm is pointed when it's mounted? I ask because I want to mount my sensors on a stationary vehicle as I live full-time in my big RV, and travel all the time. I understand the setting of the solar panel's direction to take advantage of the sun's rays as much as possible, but I'm not clear on whether this placement will affect the anemometer's readings if that arm is pointed in the wrong direction.
Good Evening Ernie. When installing the anemometer, it should point due north. If for some reason it is not, in both the WeatherLink Desktop software and WeatherLink Live, you can set an offset value to correct for this.
@@HoosierWeather This aspect of pointing due north is another concern for me, How can this be archived, how do you simply obtain the due north direction.
Hello; thanks for sharing. Normally, to enable the solar panels to absorb enough sunlight, it has to be mounted to face SOUTH. Now my question; How can this be done simply when on the field?
For the solar panel mounting, it doesn't have to be an exact science. You just want to get it in the correct general direction so that it receives the most sunlight possible, but I'll admit that I used a compass to align mine.
Not really. I don't use the fireplace much and it clears the top of it by several feet. I would have liked to put it somewhere else, but my mounting options, in places in which I wasn't risking death, were limited. :)
Thank you for this video. I was looking for a solution for how to mount my anemometer to my chimney because it is the only way to get unobstructed wind readings in my neighborhood. Do you think PVC pipe would be sturdy enough for the anemometer?
@@HoosierWeather Thank you! I switched from PVC sch40 over to a metal conduit pipe. My nerves are now settles about the potential of the PVC snapping in a high wind event.
@@HoosierWeather Yesterday, we had a storm with 1200 lightning strikes in the first hour. Personally, I would prefer not to mount metal pipe on my house. Good video, thanks for the help
There is a risk that this could happen. I did not drill any holes below ground level (except for the lag bolts) for water to drain, but the bottom opening of the hole is in soil and not concrete. This should allow any water that has collected in the pole to drain. It is something to consider, but I will probably replace the pole when the time comes for a new station. It is probably worth considering plugging that hole, if for no other reason, to keep wasps and other bugs out. Thanks for the comment and thank you for watching!
It is curious that the wind direction is reading but the wind speed is not. I am assuming the cups are spinning, is it possible the set screw has loosened? My next thought would be the cable. Do you have another straight through cable to try?
Hii this is baaji from Hyderabad India. We are frequently install this spectrum weather stations like 2550,2700,2900...But now we need this model installation. Is this any availability to chat yours. Please reply..
My apologies for the delay, it has been busy. My first thought is that 80ft is not good. However, I have seen units mounted on rooftops. Davis recommendations specifically say "You can also mount the sensor suite on the roof, between 5’ (1.5 m) and 7’ (2.1 m) above the roof surface." Additional information can be found here. www.davisinstruments.com/resource/what-is-the-best-height-at-which-to-install-my-weather-station/ www.davisinstruments.com/product_documents/weather/manuals/07395-262_IM_06357.pdf
Just the ISS itself is ~20.5", just about even with the rain collector. The spikes on the rain collector, depending on how much you push them down in to their holder, stick up about the collector about 3".
@@HoosierWeather Thank you so much for getting back to me so quickly. I have a Vantage Vue and am considering an upgrade. The fan aspiration is what I am really wanting. Currently, morning and afternoon temps when there is no wind and sun always appear about 5 degrees over.
@@HoosierWeather yep i ordered a wired one.. is the cable for the anemometer and rain gauge separate, i need to mount the anemometer on the roof and RG just about 6ft from the ground in the backyard.. chosen the cabled one coz i need to link it to APRS.
Live data is missing some properties like temp, hum etc current observation data in vantage pro 2 wireless console after data logger firmware update. Is there any way to revert back to 1.1.1
Unfortunately, reverting console firmware is something I have not tried. That might be a call to Davis Support.
Thank you for the video
Does it matter which way the anemometer's arm is pointed when it's mounted? I ask because I want to mount my sensors on a stationary vehicle as I live full-time in my big RV, and travel all the time. I understand the setting of the solar panel's direction to take advantage of the sun's rays as much as possible, but I'm not clear on whether this placement will affect the anemometer's readings if that arm is pointed in the wrong direction.
Good Evening Ernie. When installing the anemometer, it should point due north. If for some reason it is not, in both the WeatherLink Desktop software and WeatherLink Live, you can set an offset value to correct for this.
@@HoosierWeather This aspect of pointing due north is another concern for me, How can this be archived, how do you simply obtain the due north direction.
Hello; thanks for sharing. Normally, to enable the solar panels to absorb enough sunlight, it has to be mounted to face SOUTH. Now my question; How can this be done simply when on the field?
For the solar panel mounting, it doesn't have to be an exact science. You just want to get it in the correct general direction so that it receives the most sunlight possible, but I'll admit that I used a compass to align mine.
Are you concerned about mounting above the chimney? Will this affect readings?
Not really. I don't use the fireplace much and it clears the top of it by several feet. I would have liked to put it somewhere else, but my mounting options, in places in which I wasn't risking death, were limited. :)
Did you make the Aprs video you mentioned? I can’t find it.
Not yet.
Thank you for this video. I was looking for a solution for how to mount my anemometer to my chimney because it is the only way to get unobstructed wind readings in my neighborhood. Do you think PVC pipe would be sturdy enough for the anemometer?
My preference would metal. I too considered PVC (either sch40 or sch80), but over time that would more than likely get a bend to it.
@@HoosierWeather Thank you! I switched from PVC sch40 over to a metal conduit pipe. My nerves are now settles about the potential of the PVC snapping in a high wind event.
@@HoosierWeather Yesterday, we had a storm with 1200 lightning strikes in the first hour. Personally, I would prefer not to mount metal pipe on my house. Good video, thanks for the help
What keeps rain from going down into the pipe and freezing and swelling and rusting over time??
There is a risk that this could happen. I did not drill any holes below ground level (except for the lag bolts) for water to drain, but the bottom opening of the hole is in soil and not concrete. This should allow any water that has collected in the pole to drain.
It is something to consider, but I will probably replace the pole when the time comes for a new station. It is probably worth considering plugging that hole, if for no other reason, to keep wasps and other bugs out.
Thanks for the comment and thank you for watching!
how to export data from the console?
Hi i have an issue, the wind speed reading is not showing , its showing zero though the wind direction is showing correct. Please help!
It is curious that the wind direction is reading but the wind speed is not. I am assuming the cups are spinning, is it possible the set screw has loosened? My next thought would be the cable. Do you have another straight through cable to try?
Did the heat from the fireplace cause false reading on air speed and direction?
We rarely use our fireplace, but I didn't see any changes in the wind reading when we did.
Hii this is baaji from Hyderabad India. We are frequently install this spectrum weather stations like 2550,2700,2900...But now we need this model installation. Is this any availability to chat yours. Please reply..
Good Evening, Sir. I’m happy to try to answer what I can for you. What questions do you have?
What size is the key of the anemometer?
It should be a 0.05” Allen wrench.
Hello, my only option is to put weather station on top of the building... height is about 25 meters (80ft) is that very bad or good?
Can you please answer me?
My apologies for the delay, it has been busy. My first thought is that 80ft is not good. However, I have seen units mounted on rooftops. Davis recommendations specifically say "You can also mount the sensor suite on the roof, between 5’ (1.5 m) and 7’ (2.1 m) above the roof surface."
Additional information can be found here.
www.davisinstruments.com/resource/what-is-the-best-height-at-which-to-install-my-weather-station/
www.davisinstruments.com/product_documents/weather/manuals/07395-262_IM_06357.pdf
Davis recommends 6 feet above the ground for the temperature and humidity sensors to work accurately.
Hi there, can tou tell me the height of the ISS (excluding the anemometer)? From bottom of radiation shield to the tip of the UV sensor?
Just the ISS itself is ~20.5", just about even with the rain collector. The spikes on the rain collector, depending on how much you push them down in to their holder, stick up about the collector about 3".
@@HoosierWeather Thank you so much for getting back to me so quickly. I have a Vantage Vue and am considering an upgrade. The fan aspiration is what I am really wanting. Currently, morning and afternoon temps when there is no wind and sun always appear about 5 degrees over.
i like your shirt, SpaceX
Thank you, Sir.
seems to me it would have been easier to start the U-Bolt first then slip it over top of the pole and down to the desired height. But, that's just me.
It was my idea to.
i'm just here for the music
how high is the sensor from ground?
From the ground it is 33'.
@@HoosierWeather how about the rain collector?
revadan , it is 6’ from the ground to the bottom of the ISS. Planning an install?
@@HoosierWeather yep i ordered a wired one.. is the cable for the anemometer and rain gauge separate, i need to mount the anemometer on the roof and RG just about 6ft from the ground in the backyard.. chosen the cabled one coz i need to link it to APRS.
An APRS video is in my queue of videos to produce.
Safety Glasses provide no protection on the bill of the cap!
I'm all for safety but I think considering what's being worked on, it's being over done on this video.