They would have been better leaving the short broken bit out and replacing it with a spacer. You cannot weld a spring and expect it to last any time at all.
That's what I thought they were gong to do ... Toss the broken bit away ... grind a taper on the end so it's flat, then turn some old train track into a spacer :)
Ancient wisdom says, you can't polish a turd. Welding tool steel is an old school oxy-acetylene welding Zen art that used to be done on small annealed pieces that were then hardened.. The rest of this spring will remain hard but cracked the welded area will be soft & will just crack anyway as it won't have formed a eutectic weld with rest of the spring.
That will work great, right up to the point where its re-used as a suspension and then it will just snap again. But don't worry a bit of black paint will cover all the defects.
Just like most comments, this weld won't last very long at all. No matter how much welding ypu do to it,(excluding the poor weld on this spring) , the welded portion is much to brittle where a spring must be pliable to a certain amount. Sorry but thats my opinion. 11:01
I dont usually have any negative to say about what folks do in that part of the world, most of the time its pretty interesting and gets the job done but i dont think welding a coil spring is gonna last. Im guessing it from some sort of shaker deck or maybe the track tensioner on a excavator? Anyways i hope it holds up and it all works out👍🏻
It looks dangerous. Good stunt guys ! Hope it has lasts. I am not an expert, but i guess, hmm, if you weld a part , the part above the welding has lost ist tension.
That'll last as long as a weak fart in a strong wind, waste of time and effort. I was waiting for someone to get a spring coil drove thru their head. Most of the useless stuff that they do is not really dangerous this is.
Are you efing kidding me? Do you really think you can weld a broken spring and that's going to be just fine? Besides, you guys are taking a big risk compressing those springs without proper care.
Soldando un resoete para repararlo muy mal trabajo en cualquier momonto con un buengolpe adios reparaciony de vuelta a cambiar trabajo a futuro corto perdido simplemente cambiar resorte algo que no se utilize resorte en una soldadura.😢
BS no power tools what do you call the press and grinders. Also these Hacks know you can't weld springs for a number of reasons. Paintings doesn't make it perform better. What the warranty 30 feet or 30 seconds 🤔
This kind of work reminds me of my neighbor. He "fixes" rust holes by NOT removing the rust, filling the hole with spray expandable foam, then using bondo over the spray foam. It just ain't going to last.
At least force them to use gloves if can't provide safety boots what kind of owner is this and pak government need to force owner to provide safety kit
@@MICHAEL-ys3pu just you are right and Ido agree but they are not in America !!!!!in that country probably don’t have the tools !!!!!!🔴🫢🤫but yes you are right!!!!🔴🫢🤫
They would have been better leaving the short broken bit out and replacing it with a spacer. You cannot weld a spring and expect it to last any time at all.
That's what I thought they were gong to do ... Toss the broken bit away ... grind a taper on the end so it's flat, then turn some old train track into a spacer :)
Like most repairs in this country, a waste of time, you can paint a rock gold but it’s still a rock 😂
They've done a great job 😂...
5:38 писец, варят пружину!!! И сколько она прослужит??? :)))
Ancient wisdom says, you can't polish a turd. Welding tool steel is an old school oxy-acetylene welding Zen art that used to be done on small annealed pieces that were then hardened..
The rest of this spring will remain hard but cracked the welded area will be soft & will just crack anyway as it won't have formed a eutectic weld with rest of the spring.
I think the technical term for that repair is putting lipstick on a pig.
So many heavy mechanic been hurt while working on recoil springs, watching this guy doing this dangerous work in this scenario gives convulsions
Customer saw welded and painted spring - looking good :)
Ненадолго.Я думаю первые метры бульдозера с этим натяжителем и сломается пружинка рядом со сваркой.Зато покрасили))))
варить пружину вообще последнее дело
@@portugalec8829 один варит, другой на сварку смотрит сидит, вот в чем беда то еще
пружину варить нужно на косом срезе а не так как они
I'd call a massive press a power tool
Or a grinder or a welder but the craftsmen didn't make the Title.
That will work great, right up to the point where its re-used as a suspension and then it will just snap again. But don't worry a bit of black paint will cover all the defects.
This is the best repair I have ever seen. This video is proof that an unskilled and inexperienced person can survive in a society.
Just like most comments, this weld won't last very long at all. No matter how much welding ypu do to it,(excluding the poor weld on this spring) , the welded portion is much to brittle where a spring must be pliable to a certain amount. Sorry but thats my opinion. 11:01
And it will change the spring rate.
Yes Yes!!! BRAND new spring, imported from Germany today!!! ... Very Very good, brand new, exact specifications!!!
It's a coil spring, under massive tension , it won't last with bubble gum welding guys , sorry , you tried and it will fail
With Rupee at 290 per Dollar, they don't have to care. If it lasts a month, that's plenty. When it breaks, then weld it again. It's persistence.
What could possibly go wrong, I would suggest a 60 mile or 60 second guarantee!
Didn’t you mean 6 miles or 6 seconds.
"without power tools" but he got hydraulic press..................................... putaclic
Я больше всего боялся, что вылетит из под преса и перешибëт кого-нибудь......
Hmm. Angle grinder, hydraulic press, and arc welder don't count as power tools?
Every one of these filth filled videos is clickbait. Then you get all the simpletons raving over how amazing everything is.
That spring is in a constant tension even at rest, i think that would fail
I dont usually have any negative to say about what folks do in that part of the world, most of the time its pretty interesting and gets the job done but i dont think welding a coil spring is gonna last. Im guessing it from some sort of shaker deck or maybe the track tensioner on a excavator? Anyways i hope it holds up and it all works out👍🏻
Надежда умирает последней, первой будет пружина и сломается в 1 см от сварного шва.
Они же её покрасили,будет работать 100%.
Is that not the most sketch spring compressor? It'd. Take a head off if the spring wasn't snapped already.
It looks dangerous. Good stunt guys ! Hope it has lasts. I am not an expert, but i guess, hmm, if you weld a part , the part above the welding has lost ist tension.
Pure comedy 😂.
Bruh. They over here messing with a bomb.
Massive press, torches, welder and grinder are all power tools
Welding a spring??
That makes the weld stronger by painting it lol
Welded spring steel ha ha ha ha.
That'll last as long as a weak fart in a strong wind, waste of time and effort. I was waiting for someone to get a spring coil drove thru their head. Most of the useless stuff that they do is not really dangerous this is.
Они еще и подшипники лопнувшие варят:)
That was boiled in oil to expand it before putting it on. I saw that video. Oils boils at under 400c. That saved on a bearing press.
Guy in the black shirt gets his camera ready...BOY if this thing launches through the roof I got a UA-cam video!!!!!
Это по моему перебор, сварили пружину. Как сварка будет работать на сжатие и растяжение.
никак )))
Будет держатмя на краске. Не зря же они её покрасили? 😂😂😂😂😂
Главное сдать заказчику красиво. Может мы чего не знаем, если делают, значит работает, у них ведь волшебные электроды. Нужно попробовать!
Я до последнего не верил, что они будут её варить
Without power tools??? What’s a hydraulic press?? Also welding a spring changes the ability of the steel to be spring steel and will snap again.
I'm going to stop watching these videos, they give me hebe jebes!!!! There frightening!!!!!!
Вот кому надо нобелевку выдавать у них сварка будет на сжатие и растяжение работать..
I wouldn't want to be anywhere near that welded spring under tension. FOH
Working without power tools??? And there is the hydraulic press!!🙄🙄😆😆😆😆
This very dangerous how they released the spring
I can't believe they did this!
Eine Feder schweissen , Wahnsinn....
Pois é 😂😂😂😂😂😂
What do you think that hydraulic press is if not a power tool?????
Painted it and put a cobra in the spring…good as new
what a supprise we are gonna weld thje broken sprint that has been welded before quality repair no just bloody dangerous
IVE SEEN COIL SPRINGS ON CARS GO FLYING VERY SCARY THANK GOD NO ONE GOT HURT JUST CAR NEXT TO US. DIDN'T LOOK GOD. HOPEFULLY ALLAH IS ON THERE SIDE
Dorman remanufactured coil springs.
BET IT WILL LAST, BUT IF I HAD DONE IT, BOOM 💥 YIKES 😂
Will not last
Are you efing kidding me? Do you really think you can weld a broken spring and that's going to be just fine? Besides, you guys are taking a big risk compressing those springs without proper care.
Hmmmm, maybe if you didn’t overload it to begin with….
Without power tools?
I give 300% weld will not last long. No one welds springs.
NO POWER TOOLS .... how about the JACK
Grinder
Краска фуфло! Сломается рядом со швом😂
Soldando un resoete para repararlo muy mal trabajo en cualquier momonto con un buengolpe adios reparaciony de vuelta a cambiar trabajo a futuro corto perdido simplemente cambiar resorte algo que no se utilize resorte en una soldadura.😢
Soldar mola ,isso é o cúmulo, do absurdo ,se o material ,original quebrou, imagina, à solda aff.
"A Craftsman without power tools" He's using a hydraulic press that's the size of a truck. Thats a very powerful power tool U 🤡
BS no power tools what do you call the press and grinders. Also these Hacks know you can't weld springs for a number of reasons. Paintings doesn't make it perform better. What the warranty 30 feet or 30 seconds 🤔
cant weld spring steal
Well they just did! So there!
Yes you are correct 😊
Using power tools
هذا العمل مضيعه للوقت والمال
клоуны пружины не варят. это то же самое что и сломанную рессору приварить.
Клоуны и не варят, а вот они варят, даже коленвалы🤗.
они еще поршни варят )
Да вроде гдето в видео у них они там ресоры варят.
Они всё варят..
Tudo feito a culhão, na marra .
Zzz
This kind of work reminds me of my neighbor. He "fixes" rust holes by NOT removing the rust, filling the hole with spray expandable foam, then using bondo over the spray foam. It just ain't going to last.
Deberían fabricar sus propios resortes en vez de repararlo
At least force them to use gloves if can't provide safety boots what kind of owner is this and pak government need to force owner to provide safety kit
LOL, this is one of the most corrupt countries in the world. Force?? HA!
Welding and paint will make you the repairman you ain't
Nice but not sure it'll last long.
My respect to the kids they are doing a fantastic job !being around the masters is the best thing they can do !🔴🤫🫢
No the best thing they could do is go to school, get a trade and learn how to repair things correctly, in a work shop not in the dirt!
@@MICHAEL-ys3pu I guess you are missing the point that is why they are so good in what they do !!!,🔴🫢🤫
@@Sl20 no , they are not learning go methods just rough as guts repairs, things that are dangerous!
@@MICHAEL-ys3pu just you are right and Ido agree but they are not in America !!!!!in that country probably don’t have the tools !!!!!!🔴🫢🤫but yes you are right!!!!🔴🫢🤫
@@Sl20 Thanks Sloop, no I don’t think it’s America and I’m not in America either. Poor practices are poor practices where ever they are.
Without power tools?
Must be a kid on a bike powering the welder.
Zzz