I would have used this out in the field where there's no table, or on existing upright. It looks like it works. It's better than magnets. Magnets can shift and move. Also when taking they don't prevent the steel from moving. This device would hold it in place to get all your tacks in. And the part of it doing an angle. most magnets would not give you an odd angle but you could with this device. I was a skilled trade welder at Ford. worked on the floor in maintenance and in the Fab shop. I could have used such a thing then. We used to make a lot of devices to make a production kind of job move faster. When your in the Fab shop and have a few hundred pieces to make all the same it would have been handy. Don't knock this idea unless you have a way better one. Also it looks like you could use it on wood, where no magnets would work. Thanks for your demonstration. It's good to have ideas. That's what makes us builders and not couch potatoes.
Never even mentioning that U-channel and C-channel are NOT square on the inside, thus the tool is never going to be aligned properly. For those who don't understand what I'm talking about, just look at the left and right inside walls of the "tool" he's made, they're not parallel, because this steel stock is only square on the OUTSIDE. The inside is rounded, and the walls get thinner closer to the edge.
I can't see the video. Bad reception. Just from the remark he can just grind the 2 inner curves to flat inner sides. If that would help for what it's supposed to be used for. My internet still just keeps spinning
I understand what you're saying. I am not a professional welder. I am, however a professional auto mechanic with plenty of welding experience. You're right about the C channel being not squared on the inside! But, bed channel iron is.
Is there any way you could possibly drag it out to last 10 or 15 minutes even longer? Maybe use slow motion to show knocking and brushing off the slag?
It's fine if you have the use for it. It will work for holding any material of a similar size at a specific angle while attaching. Magnetic solutions are limited to steel
Во-первых, швеллер должен быть гнутый, а не катаный (углы на внутренних стенках не позволят позиционировать детали). Во-вторых, в цивилизованном мире квалифицированный рабочий не тратит своё время на изготовление подобного металлолома. Существует масса оснастки для сварки - магнитной и зажимной, зачем изобретать велосипед?
I found this interesting! This tool is so simple but can solve many problems in places where there are no magnetic clips. Thanks for sharing this video! ❤❤❤
! Simplemente Maraviyoso !, muchas Gracias por compartir tus conocimientos y talentos👍. "BENDICIONES Del PADRE ALTÍSIMO". carlos rafael ORTEGA GÓMEZ, BARQUISIMETO-VENEZUELA...💨🕊️
A decent idea but you really need to go to trade school to learn how to weld properly. Every time you stop you must clean the slag off or it gets melted into the next weld spot and weakens the weld a lot.
Nice , but, the process to make the fixture is too long. Anyway, your fixture will help welders to fabricate joint welding easily. A good tool for welders who are beginners. 👍
@Bear-ht6vf Well, actually… if I were you, I, personally, would NOT look at the whole 10 minutes and 10 seconds you spent, watching this useless video, as well as the subsequent 30 seconds you spent to leave your comment, a complete and total waste of your valuable time!!! I mean, just look at it this way, if you don’t mind, as I promise you that looking at it from this “other” perspective will make you feel a whole lot better about “wasting” 10 minutes of your life that you’ll never get back… so, PLEASE believe me when I say this, but even though you were absolutely correct when you said, “that’s 10 minutes and 10 seconds of my life I’ll NEVER get back”, it is NOT, in and of itself, a complete waste!!! And I say that simply based on the sole fact that you, yourself, watched this video, evidently in its entirety, left a comment about this video being, in not so many words, “a waste of time”, at which point I come along, see, and read, your comment and then decide, “this crappy video, most likely, does NOT contain any usable and/or useful information AND if I cannot be, at the very least, somewhat entertained and/or learn something from this video, due to the fact that it does NOT contain any pertinent information, then this video is, in fact, USELESS, to me and others, and it is absolutely NOT worth the 10 minutes that it will take to watch this video, thereby saving ME, AND MORE THAN LIKELY HUNDREDS, IF NOT THOUSANDS, OF OTHER PEOPLE from having to sit through the whole 10 minutes and 10 seconds of this useless and shitty video!!! So, as you can see, in the end, your ten minutes save a whole bunch of other people the 10 minutes and 10 seconds that it would’ve took them to watch the video just to figure out the same thing you did… which is, this sorry ass video is NOT worth watching!!! Now, if you figure it this way… if your 10 minutes and 10 seconds, that you spent, just to find out that this video sucks, ONLY SAVED JUST 100 PEOPLE, even though I’m VERY SURE that it was WAY MORE THAN JUST 100 people… SO, I AM JUST USING 100 PEOPLE AS AN EXAMPLE, BUT EITHER WAY, 100 PEOPLE MULTIPLIED BY THE 10 MINUTES AND 10 SECONDS THAT IT WOULD’VE TAKEN EACH PERSON TO WATCH THE VIDEO EQUATES OUT TO BE RIGHT AROUND… NOW, ARE YOU SURE THAT YOU’RE REALLY READY FOR THIS, BECAUSE I THINK YOU ARE ACTUALLY UNDERESTIMATING EXACTLY WHAT IT WAS THAT YOU DID JUST BY WATCHING THIS VIDEO AND THEN COMMENTING AND MAKING EVERYONE AWARE!!! SO, 10 MINUTES AND 10 SECONDS MULTIPLIED BY 100 PEOPLE COMES OUT TO A TOTAL OF SOME… 16 HOURS AND 16 MINUTES, if my calculations are correct, THAT YOU, SINGLE-HANDEDLY, SAVED JUST 100 PEOPLE FROM WASTING!!! AND IF IT WAS A 1,000 PEOPLE WHO DIDN’T WATCH THE VIDEO BECAUSE OF YOU THEN MULTIPLY THAT 16 HOURS BY 10… SO THATS 160 SOME ODD HOURS THAT YOUR 10 MINUTES AND 10 SECONDS SAVED EVERYONE FROM WASTING ON THIS VIDEO!!! I WOULD SAY THAT IT WAS VERY MUCH WORTH YOUR 10 MINUTES, NO!?!?!? JUST SO YOU KNOW, THAT IS WHAT WE CALL A “HERO” HERE ON UA-cam!!! And for that, I WOULD JUST LIKE TO THANK YOU, TO THE MAXIMUM EXTENT ALLOWABLE HERE ON UA-cam, FOR SAVING ME AND MANY OTHERS FROM SITTING THROUGH A VIDEO THAT SHOULD’VE BEEN DELETED 5 MINUTES AFTER IT WAS UPLOADED AND POSTED TO UA-cam!!! So, AGAIN… THANK YOU SO VERY MUCH FOR THE TIME YOU SAVED, NOT ONLY, ME… BUT MOST LIKELY SO MANY OTHERS!!! #✌️❤️😁
Możesz nie potrzebować (tak jak ja), ale wypada mieć szacunek do cudzej pracy. Dla ludzi którzy robią takie rzeczy urządzenie jest przydatne, a tym którzy wchodzą wylewać swoją żółć nic nie jest potrzebne. Brawo Asiu!!
Actually this is way too complicated solution for a problem which was resolved about 80 years ago with 90°and 45° cheap magnetic jigs. Those ARE simple.
Also, there's the fairly obvious and oft-forgotten backwardsness of "I'm putting this up and *then* assembling it, when I should be assembling it and *then* putting it up."... and *then* there's building a tool to help you with putting things up and *then* assembling them more often. This clamp that most people don't know about will hold the gun perfectly while you aim it at your foot!
Here's a curious question I'd be interested in knowing the answer to! Why don't we get 'Arc Flash' when watching welding on a screen but we do when casually walking past a live example! I once got Arc Flash and I was a few yards away from it. It was like having sand or grit in my eyes for a couple of days.
هرکس که شغل فنی داشته باشه..و از حرفه های خودش برای درست کردن ابزارهایی که توی بازار کم پیدا میشه ولی خود آدم میتونه بسازه و دیگه نیاز به شاگرد یا کسی بیاد براش قطعه رو بگیره نداره.❤❤
It depends on the magnet! You have small magnets and large magnets that you can hardly separate from the material! The 4 middle magnets cannot be moved at all! You place a couple of pieces and tap the magnet with a hammer until you get it to the required size. Then you add two more for the opposite 90° leveling! Nothing can move, and the pipes don't have to lie perfectly because first you weld by "stitching" in 4 corners to prevent deformation and bending, and then you weld a full weld. The result is ideal! Magnets are "the law"! That is why they are used massively in all countries of the world!🧐☝👍👍👍
Me parece una estupenda idea. Es una herramienta, que en lo personal, considero de michisima ayuda. Muchas gracias por compartir. Siempre lo he seguido pero con otra cuenta (Ernesto Robledo). Saludos desde Gutierrez Zamora, Veracruz México... Que la envidia no lo haga tropezar, usted tiene un estupendo canal aquí en UA-cam...
For the guy who simply HAS to build all of his tools that’s cool. But a magnet would have save a lot of time. Plus I get the spot welding deal but you are not getting any penetration at all with those short hits. You need to stay on it a few seconds.
I'm one of the millions to whom this tool is a revelation. How I can incorporate it into my daily life as a small town solicitor is a challenge to which I am looking forward.
@@anthonyboomer641 Wow! you're a bundle of laughs, aren't you? I was responding to welding in steel according to the video. When I weld "aluminium" I use an adjustable jig. I assume you're a chap across the pond so I'll keep it simple, uppercase is a way of shouting, if you were before me and shouting you would soon be needing our wonderful NHS. Here in the civilised World, we use "Aluminium", not the butchered version "aluminum" you colonials have picked up. I hope you've found this as it has left me.....Educated.
"This video not only teaches a useful skill but also motivates us to think outside the box. Fantastic work!" Lesson: Thinking creatively can lead to innovative solutions; embrace the challenge of problem-solving.
@@viking2694 When I weld "ALUMINIUM/ALUMINUM", I also use a jig, however I would gladly use the "Bracket" in question as well. I live by the proverb," What you dismiss today, you may need tomorrow". Do not be so quick to judge.
Granted I'm only 4F certified, but why does he weld everything like it's sheet metal and going to warp. Also, just tack it in place and twist til it's adjusted, add a few more tacks and then weld it.
Лучшего приспособления в жизни я не видел, это гениально,срочно пойду и сделаю твких пять штук, но для чего они ме нужны,не знаю .
🙏
@@asiawelderIt’s sarcasm asia😂
GETTOUTT@@kent7260
Не знаете, для чего это нужно?
Должно быть продано. (!)
😂😂😂
I would have used this out in the field where there's no table, or on existing upright. It looks like it works. It's better than magnets. Magnets can shift and move. Also when taking they don't prevent the steel from moving. This device would hold it in place to get all your tacks in. And the part of it doing an angle. most magnets would not give you an odd angle but you could with this device. I was a skilled trade welder at Ford. worked on the floor in maintenance and in the Fab shop. I could have used such a thing then. We used to make a lot of devices to make a production kind of job move faster. When your in the Fab shop and have a few hundred pieces to make all the same it would have been handy. Don't knock this idea unless you have a way better one. Also it looks like you could use it on wood, where no magnets would work. Thanks for your demonstration. It's good to have ideas. That's what makes us builders and not couch potatoes.
🙏
000000000⁰
@@barracuda861 Извини ,но на самом деле накрутил ,заморочил,а всё так просто
Never even mentioning that U-channel and C-channel are NOT square on the inside, thus the tool is never going to be aligned properly. For those who don't understand what I'm talking about, just look at the left and right inside walls of the "tool" he's made, they're not parallel, because this steel stock is only square on the OUTSIDE. The inside is rounded, and the walls get thinner closer to the edge.
Well done highlighting all of the flaws with this useless tool.
Is not a c chanel, is a bent plate brother
I can't see the video. Bad reception.
Just from the remark he can just grind the 2 inner curves to flat inner sides.
If that would help for what it's supposed to be used for.
My internet still just keeps spinning
I understand what you're saying. I am not a professional welder. I am, however a professional auto mechanic with plenty of welding experience. You're right about the C channel being not squared on the inside! But, bed channel iron is.
@@josegardead8946 It is absolutely not a bent plate
Два сварочных магнита решают проблему проще и эффективнее
🙏
Espectacular la herramienta,yo hago herrería y carpintería y la aplicó en las dos cosas 👍👍🇦🇷🇦🇷
🙏🙏💐
Wouldn't it be great if we could all be such smart alecs and come up with stuff like this.
🙏
@@asiawelder Вот видишь, не все идиоты.
Кто не хочет потерять десять минут,просто перемотайте видео. Поймете что хрень и не расстроитесь за потраченое время.
Поздно...
🙏🙏
Блин, опоздал
Is there any way you could possibly drag it out to last 10 or 15 minutes even longer? Maybe use slow motion to show knocking and brushing off the slag?
I watched it on double speed, and it still dragged on. At least I now know about a homemade tool I will never need.
@@Ron-0417 Lol. I think I watched a 20 sec version - by clicking on the last section to start with. It was still too long.
You watched it. No one twisting your arm.
Why do people watch this stuff if they don't want to learn anything
🙏🙏
Very good, don't feel bad about the negative comments, that all some of us can do, excellent tool bro
🙏
Most people watching will never use this tool, including me. Was very cool to watch build and useful for welders. I found it interesting.
1:17
PLANFARACACHAMBATA.
I'm glad I fast forwarded through most of it.
🙏
Me too
Me too, knowing most likely it is a clickbait.
handy to see how to make one. very useful
Fortunate.
It's fine if you have the use for it. It will work for holding any material of a similar size at a specific angle while attaching.
Magnetic solutions are limited to steel
🙏
Gracias por compartir tus grandes ideas
🙏
Are you saying that sarcastically?
IDEIA MARAVILHOSA PARABÉNS
🙏🙏
Полка швеллера имеет поверхность с уклоном, соответственно из него не получится приспособление которое будет ровно зажимать свариваемые заготовки !
🙏
Tc-c-c!!! Тихо! Об этом знают только на просторах бывшего СССР.😂
Швеллер бывает с буквой "У" - с уклоном граней и с буквой "П" - с прямыми гранями.
есть сорт швеллера без этой проблемы. Крановый , что ли.
@@sanek66 😂😂😂
뭐가 나오나하고 유심히 나름 상상하고 보았는데 역시나 현장에서는 그다지 필요할지 ?
수고 많으셨습니다 🎉🎉🎉
🙏
10 minute video that could have been shortened to 30 seconds. Fail.
🙏
stone age technology........
Hahaha 😆
@aktharismail643 Почему? Идея хорошая.
What an ungrateful people 😤
Da gibt es genug Alternativen, aber in Länder wo es nichts gibt ist es brauchbar
🙏
Wenn du mich fragst, völlig unnötiges Werkzeug.
МУЗЫКУ УБЕРИТЕ. МЕШАЕТ.
Don't let negative comments bother you...
I see you make do with what you have on hand.
🙏
Agreed with you, you can’t pleased everyone so don’t let those comments bother you.
I’d be bothered by the positive comments if I were you. It means that you have competition in the most boring, irrelevant welder on UA-cam.
The tool is very useful; thank you for sharing. I’ll try to make this tool.
Many wishes!
🙏🙏
I have been a fitter for 40 years and have never had a use for that tool.
👍🙏
Но,определëнные удобства есть,от применения этого приспособления.Причина вашего неприятия ,возможно исходит ,от неспособности создавать подобные вещи.
Talking about the construction, or the constructor?
highly skilled metal fabricators must be proud not from the stone age technology....
Then you’ve never been a real fitter .. don’t be jealous just because he’s Asian. Give him his due.. Jesus Christ, anything to be a hypocrite
The moral of this video: SAY NO TO DRUGS! Edit: Actually, a big fat YES would be more appropriate.
🙏
As a Welder myself, I appreciate a good holding device! I’ll give you a two thumbs up👍👍 nice presentation for the beginning, fabricators and welders!
🙏🙏
It’s easier and more precise to do the same with magnets 😊
🙏
thank God. I don't know how I lived without it.
🙏🙏
hahahaha, i completely understand
😊
Now I know why millions of people don't know about this it's rather stupid
@@asiawelderНе обращай внимания на идиотов.❤️💋🌹
Structural welds should be made from above, opposite of gravity so that the molten metal is pulled into the joint.
🙏
GOOD IDEA, SIMPLE TOOL FOR FABRICATION WORK
🙏
Во-первых, швеллер должен быть гнутый, а не катаный (углы на внутренних стенках не позволят позиционировать детали). Во-вторых, в цивилизованном мире квалифицированный рабочий не тратит своё время на изготовление подобного металлолома. Существует масса оснастки для сварки - магнитной и зажимной, зачем изобретать велосипед?
🙏
You are beyond my wildest dreams. Thank you very much.
🙏
Watching the arc welding took me back more than 50 years to my apprentice days, and I can still smell the fumes. 😊
🙏🙏
Sorry - last night's curry...
Good idea, but there are strong magnets with useful angles (90°, 45°, 30°) to do the same job...
🙏
I found this interesting! This tool is so simple but can solve many problems in places where there are no magnetic clips. Thanks for sharing this video! ❤❤❤
🙏🙏🎉
Good project for her community ❤❤❤🎉🎉🎉🎉🎉
🙏💐💐♥️
You will never get the time wasted watching this back in your life 👽🥃
🙏
You got to be kidding! My fellow welders would laugh me off the job if I showed up with something like that.
🙏
They will laugh at you for this dummy coment ha ha ha !!! I like this tool and idea.
@@GeorgeFranquiz do you wear a dress?
So how many views did your last UA-cam video get. I am guessing not 400K So which one of you is the smartest now.
@@JohnNaturkach Nope, but I know you do
! Simplemente Maraviyoso !, muchas Gracias por compartir tus conocimientos y talentos👍. "BENDICIONES Del PADRE ALTÍSIMO". carlos rafael ORTEGA GÓMEZ, BARQUISIMETO-VENEZUELA...💨🕊️
🙏🙏
okay, it took till the end, but you are a genius!!! well done, I gotta make one. mike
🙏
A decent idea but you really need to go to trade school to learn how to weld properly. Every time you stop you must clean the slag off or it gets melted into the next weld spot and weakens the weld a lot.
🙏
It's not a pression job so don't bother
NO creo que este soldando un cazó de una excavadora, no me jodas, para eso es suficiente, hay mucho enterado.
Manche können alles im Laden kaufen, andere bauen es selbst.
Tolle Idee, danke dafür.
🙏
Verry nice welding and workman ship,
🙏
What is the brand of cutoff wheel your using??
🙏
Great! but ... Millions of people know the magnet. Millions of people know another person who helps them.
🙏🙏
~Masz rację - Miliony ludzi znają takich którzy tylko hejtują pracę innych. Powiedz co sam zrobiłeś??😀
@@KrzysztofKowalewski-ts9pv Codziennie poprawiam błędy innych
Nice…innovative!! 👏👏
🙏
Nice , but, the process to make the fixture is too long. Anyway, your fixture will help welders to fabricate joint welding easily. A good tool for welders who are beginners. 👍
🙏🙏
Мыла в миллион раз больше чем информации
A little oil will go a long way to make the holes easier to drill. Drill bit will last longer too. And, how come still using a stick welder?
🙏
That's 10 minutes and 10 seconds of my life. I'll never get back.
🙏
I wasn't willing to give up that much time so I went to the end of the vid to see the result, definitely a waste of time.
It's about appreciating ingenuity
@Bear-ht6vf
Well, actually… if I were you, I, personally, would NOT look at the whole 10 minutes and 10 seconds you spent, watching this useless video, as well as the subsequent 30 seconds you spent to leave your comment, a complete and total waste of your valuable time!!! I mean, just look at it this way, if you don’t mind, as I promise you that looking at it from this “other” perspective will make you feel a whole lot better about “wasting” 10 minutes of your life that you’ll never get back… so, PLEASE believe me when I say this, but even though you were absolutely correct when you said, “that’s 10 minutes and 10 seconds of my life I’ll NEVER get back”, it is NOT, in and of itself, a complete waste!!! And I say that simply based on the sole fact that you, yourself, watched this video, evidently in its entirety, left a comment about this video being, in not so many words, “a waste of time”, at which point I come along, see, and read, your comment and then decide, “this crappy video, most likely, does NOT contain any usable and/or useful information AND if I cannot be, at the very least, somewhat entertained and/or learn something from this video, due to the fact that it does NOT contain any pertinent information, then this video is, in fact, USELESS, to me and others, and it is absolutely NOT worth the 10 minutes that it will take to watch this video, thereby saving ME, AND MORE THAN LIKELY HUNDREDS, IF NOT THOUSANDS, OF OTHER PEOPLE from having to sit through the whole 10 minutes and 10 seconds of this useless and shitty video!!! So, as you can see, in the end, your ten minutes save a whole bunch of other people the 10 minutes and 10 seconds that it would’ve took them to watch the video just to figure out the same thing you did… which is, this sorry ass video is NOT worth watching!!! Now, if you figure it this way… if your 10 minutes and 10 seconds, that you spent, just to find out that this video sucks, ONLY SAVED JUST 100 PEOPLE, even though I’m VERY SURE that it was WAY MORE THAN JUST 100 people… SO, I AM JUST USING 100 PEOPLE AS AN EXAMPLE, BUT EITHER WAY, 100 PEOPLE MULTIPLIED BY THE 10 MINUTES AND 10 SECONDS THAT IT WOULD’VE TAKEN EACH PERSON TO WATCH THE VIDEO EQUATES OUT TO BE RIGHT AROUND… NOW, ARE YOU SURE THAT YOU’RE REALLY READY FOR THIS, BECAUSE I THINK YOU ARE ACTUALLY UNDERESTIMATING EXACTLY WHAT IT WAS THAT YOU DID JUST BY WATCHING THIS VIDEO AND THEN COMMENTING AND MAKING EVERYONE AWARE!!! SO, 10 MINUTES AND 10 SECONDS MULTIPLIED BY 100 PEOPLE COMES OUT TO A TOTAL OF SOME… 16 HOURS AND 16 MINUTES, if my calculations are correct, THAT YOU, SINGLE-HANDEDLY, SAVED JUST 100 PEOPLE FROM WASTING!!! AND IF IT WAS A 1,000 PEOPLE WHO DIDN’T WATCH THE VIDEO BECAUSE OF YOU THEN MULTIPLY THAT 16 HOURS BY 10… SO THATS 160 SOME ODD HOURS THAT YOUR 10 MINUTES AND 10 SECONDS SAVED EVERYONE FROM WASTING ON THIS VIDEO!!! I WOULD SAY THAT IT WAS VERY MUCH WORTH YOUR 10 MINUTES, NO!?!?!?
JUST SO YOU KNOW, THAT IS WHAT WE CALL A “HERO” HERE ON UA-cam!!!
And for that, I WOULD JUST LIKE TO THANK YOU, TO THE MAXIMUM EXTENT ALLOWABLE HERE ON UA-cam, FOR SAVING ME AND MANY OTHERS FROM SITTING THROUGH A VIDEO THAT SHOULD’VE BEEN DELETED 5 MINUTES AFTER IT WAS UPLOADED AND POSTED TO UA-cam!!! So, AGAIN… THANK YOU SO VERY MUCH FOR THE TIME YOU SAVED, NOT ONLY, ME… BUT MOST LIKELY SO MANY OTHERS!!!
#✌️❤️😁
Para que carajos miran si después se van plagear como viejas!!😂
Excelente trabajo amigo muy eficiente herramienta la que acabas de hacer
🙏🙏
quiza hay mas simple
Для этого давно придуманы магнитные уголки😮
🙏
To a welder like me it's very helpful but still think the tittle was a bit misleading as it is actually a workshop tool
🙏
I’m definitely one of the millions that don’t need this homemade tool.
🙏
I do!
Billions
what a shame !
this man from stone age......?
Możesz nie potrzebować (tak jak ja), ale wypada mieć szacunek do cudzej pracy. Dla ludzi którzy robią takie rzeczy urządzenie jest przydatne, a tym którzy wchodzą wylewać swoją żółć nic nie jest potrzebne. Brawo Asiu!!
Very genius.I think how can you thinking out this simplest useful tool.
Actually this is way too complicated solution for a problem which was resolved about 80 years ago with 90°and 45° cheap magnetic jigs. Those ARE simple.
🙏
سلام
ابزار خوبی بود
ولی زیادی وقت گذاشتین برای نمایش دادن آدم رو خسته میکنه.
🙏
Pretty slick idea. Thanks for sharing.
🙏🙏
He calls himself a welder and welds in gardening gloves, interesting. PS there are extremely cheap magnetic clamps that will do that exact same task.
🙏🙏
People can’t always afford the things that we take for granted.
@@_just_looking_thank_you Nonsense.
Also, there's the fairly obvious and oft-forgotten backwardsness of "I'm putting this up and *then* assembling it, when I should be assembling it and *then* putting it up."... and *then* there's building a tool to help you with putting things up and *then* assembling them more often. This clamp that most people don't know about will hold the gun perfectly while you aim it at your foot!
Probably has safety sandals on too 😂
Here's a curious question I'd be interested in knowing the answer to! Why don't we get 'Arc Flash' when watching welding on a screen but we do when casually walking past a live example! I once got Arc Flash and I was a few yards away from it. It was like having sand or grit in my eyes for a couple of days.
🙏🙏
هرکس که شغل فنی داشته باشه..و از حرفه های خودش برای درست کردن ابزارهایی که توی بازار کم پیدا میشه ولی خود آدم میتونه بسازه و دیگه نیاز به شاگرد یا کسی بیاد براش قطعه رو بگیره نداره.❤❤
🙏🙏
Can you buy this tool at HFT cheaper than it can be made?
🙏
Your IQ is directly related to your ability to improvise..🍷😎👌
🙏🙏🎉
Stop worrying about your IQ
@@kent7260
No worries here Kent.. Are you having a bad day? 😿
👋👋👋👋👋👋 obrigado pela partilha de conhecimentos.🇦🇴🙏
🙏🙏🎉🎉
❤❤❤❤
My boss would fire me on the spot for using something like that!
🙏
Nicely Done 👏🏽👏🏽👏🏽
🙏🙏
For those of us only born with two hands this is an excellent tool.
🙏🙏
It depends on the magnet! You have small magnets and large magnets that you can hardly separate from the material! The 4 middle magnets cannot be moved at all! You place a couple of pieces and tap the magnet with a hammer until you get it to the required size. Then you add two more for the opposite 90° leveling! Nothing can move, and the pipes don't have to lie perfectly because first you weld by "stitching" in 4 corners to prevent deformation and bending, and then you weld a full weld. The result is ideal! Magnets are "the law"! That is why they are used massively in all countries of the world!🧐☝👍👍👍
🙏
Awesome tool. Very interesting channel.
🙏
I learned a couple of techniques that I hadn’t thought about, thank you.
🙏
100s of millions of people don't need this tool
🙏
Редкий приметив
Well then they will not need to make the tool if they dont need it , will they.
Lol
🎉🎉🎉🎉🎉
So,Mr. Asia Welder,what's the name of the tool and what is it used for?
Clamp sudut 🙏
Sheesh! All that work when a 90 degree magnet for $2 will do the same! Lol
🙏
Me parece una estupenda idea. Es una herramienta, que en lo personal, considero de michisima ayuda. Muchas gracias por compartir. Siempre lo he seguido pero con otra cuenta (Ernesto Robledo). Saludos desde Gutierrez Zamora, Veracruz México...
Que la envidia no lo haga tropezar, usted tiene un estupendo canal aquí en UA-cam...
🙏🙏
I just can’t believe what a waste of time !! Energy & material !
🙏
Buenísimo!!! Espectacular, soy Jorge!
🙏
They're just jealous of your work lol Ignore the haters. 🎃
🙏
exactly.
I didn't burn my retinas watching the welding. Great camerawork, like I was there.
🙏🙏
Ты точно там не был 😂
This is one of the most innovative things I ever watched. Well done. 👏👏
🙏
Necessity is the mother of invention !
🙏
This is a tool that millions dont know but 8.000.000.000 dont need.
I wish i had slept for the last 10 minutes. How did it get so many likes?
🙏
Très bonne idée, bravo !!!!!!!!!!!
👍👍👍👍
🙏💐
Cuánto se tardó el artefacto está ingenioso inteligencia truco de video a perro
Я всегда подставлю, прихвачу. Потом выровнял. На глаз, или уровнем. Человек заморочился. Ну нравится ему, и дай бог. 👍👍👍
🙏🙏
Great idea
👌
🙏🙏
Открою тайну---в магазине "инструмент", есть магнитный угольник.... (не благодарите...)
🙏
это из той поговорки, когда дурная голова рукам покоя не даёт )))))
Магнитный угольник не удержит профиль так, как показано на видео.
@@ИванЗагляда-н8ы, А зачем его удерживать? Можно с таким же успехом положить на ровную поверхность, прижать и приварить.
For the guy who simply HAS to build all of his tools that’s cool.
But a magnet would have save a lot of time.
Plus I get the spot welding deal but you are not getting any penetration at all with those short hits.
You need to stay on it a few seconds.
🙏
Parabéns!
Ótima ferramenta!
🙏🙏
I'm one of the millions to whom this tool is a revelation. How I can incorporate it into my daily life as a small town solicitor is a challenge to which I am looking forward.
🙏
That's some of my life I'll never get back !!!
😂
🙏
Inspirative 👍👍
🙏🙏
great thank you, very meaningful
🙏🙏
@@asiawelder=ha ha ha
Gaiety 💅.You are great Monsieur 🙏🇮🇳.
🙏
Kewl design as long it works! Ignore the negatives! As long we get the job done!!
🙏
What an ingenuous idea, WOW
🙏
I use a paper sack. I get it at Aldi grocery for 10cents.
🙏
I like- great idea! 👍
🙏🙏💐
Pretty clever for sure
🙏
Excellent work!!
🙏🙏
Intricately simple but effective. Good job!!!! Gets people thinking mechanically , better than most of the crap today on UA-cam.
🙏
And nobody wants to watch you strike an arch fourty times !
عالی بود و کاربردی و مفید👏👍
🙏🙏
I’m making 10 of these…. Thanks!👍🏾
🙏
Clever! Thanks for the video!
🙏
I might actually need this…..thanks for posting
🙏
У нас на заводе такие вещи назывались кондуктор. обычно, рабочие сами это всё придумывали.
🙏
We have magnets for that
🙏
"OH BOY!!! THAT SOUNDS GREAT, BUT CAN YOU TELL ME HOW MAGNETS WORK ON ALUMINUM???" HA, HA, HA!
@@anthonyboomer641 Wow! you're a bundle of laughs, aren't you? I was responding to welding in steel according to the video. When I weld "aluminium" I use an adjustable jig. I assume you're a chap across the pond so I'll keep it simple, uppercase is a way of shouting, if you were before me and shouting you would soon be needing our wonderful NHS. Here in the civilised World, we use "Aluminium", not the butchered version "aluminum" you colonials have picked up. I hope you've found this as it has left me.....Educated.
"This video not only teaches a useful skill but also motivates us to think outside the box. Fantastic work!" Lesson: Thinking creatively can lead to innovative solutions; embrace the challenge of problem-solving.
@@viking2694 When I weld "ALUMINIUM/ALUMINUM", I also use a jig, however I would gladly use the "Bracket" in question as well. I live by the proverb," What you dismiss today, you may need tomorrow". Do not be so quick to judge.
Granted I'm only 4F certified, but why does he weld everything like it's sheet metal and going to warp. Also, just tack it in place and twist til it's adjusted, add a few more tacks and then weld it.
🙏