Відео

Hahaha

And that's how Craftsman tools are made now.

Good job

Why no workbench for washing the parts ? What was wrong with the pump, nothing replaced..It’s a mystery..😳😳

👍bom, positivo👏👏👏

Вот это перевозка обычного песка , и как они этот песочек утрамбовали тентом укрыли - респект трудягам 👍😱🤔🤌

Now there's some good working conditions ay?

Good job brother injection pump repair

❤❤

I need a job ?

These are worker exploitation videos. Why are these allowed on you tube? This one even advertises child exploitation. Do not give this video a like. No saftey equipment. Not even safety glasses.

Dont keep em in order, doesnt matter the cams all have fresh hammer marks!

Dio mio che creature straordinarie, sembrano formiche più che uomini!

یار بولو تو سہی کیا کر رہے ہو ۔

Good job 👍👍👍👍👍👍👍👍

Bhai location btai ya mujhse rabta kre

Bhai location btai ya mujhse rabta kre

Bhai apki location Kia hy

Bhi mujhe v sikha doo

Good job idol...

Used to do this with inline pump but still on engine. No gloves just barrier cream.

Bahtarin

Amazing Job!.

Good

δηλαδή αυτό που βλέπουμε ειναι επισκευή αντλίας πετρελαίου,,,,ρε πατε καλα.,,,μετα από 43 χρονιά μηχανικος του Ε.Ν δεν εχώ λογία να περιγράψω αυτά που βλέπω

👍👍👍👍

El cilindro 2 ni siquiera inyectó!

Good job👍👍👍

Cancer causing agents in that solvent. That boy should be wearing gloves!

ce qui est déplorable c'est qu'ils galope comme des lapin pour montrer qu'ils savent bosser on a le temps de voir a peine et en plus ils ne respecte pas les consignes de sécurité et de propreté bref du show et rien de plus absolument pas intéressent !

Put oil while testing

عمل احترافى وممتاز ونظيف جدا الله يبارك فى صنعتكم فى الحقيقة ظبط المضخى الوقود ليس بل امر السهل يحتاج اخبرة2:48 عالية كبيرة بتوفيق

So all I saw was a teardown and clean, reassemble and run on machine without oil, tweak fuel amounts so they're even. When was the fault identified?

asia?money

It will break again it became looser than before loose things don't last for long not good enough

Slight change in setting and vehicle starts burning more fuel with less power being produced by engine

Not every mechanic can set this component right. Fuel efficiency solely depends on this fuel pump.

I kew a guy in his mid 30 his hands & finger nails were deformed from not wearing gloves for 2 1 half decade

No reamer, that is the sloppiest king pin fit I have ever seen.

mantap...sangat luar biasa...

Idle ok, speeding up clear hammering. They were lucky the original built is close to perfection, but I bet that this engine will be used nonstop and develop more and more vibration. Very lucky.

Làm từ từ thôi a dai , ai hối đâu màaaaaa😂

Wonder how long it'll run after this "repair"...

Could someone please give these brilliant young fellas some latex gloves 😊

А где ремонт? Они же просто помыли топливный насос высокого давления 😂😂😂

Steel toed sandalled boy didn’t , the diagnosis machine did

😂😂 عمل جيد اتمنى مزيدا من النجاح 😮😮 حتى من صنعها لا يستطيع إصلاحها ويقول لك اشتري قطعة جديدة

Looks like a wimer

It’s not good practice to weld over slag. The metal will lose a lot of its potential strength. Which was insufficient to start with since it broke. I would tell the truck owner to cut the loads by 50% if he wants to keep using the truck without weekly breakdowns.

Not bad, kids in the US can't decide if they're male or female.