Nice video I changed the camshaft position sensor on my Nissan march 2009 I changed every sensor but it's still start sometimes sometimes not if it's start it idle rough
Hi thanks, Do any codes come up on the diagnostic computer? The other common fault for such issue would be changing the complete throttle body including the air box, you can try cleaning just the throttle body (pls see my other videos as I show step by step guide how to clean the throttle body) Hope this helps & hope you get your car sorted and bk on the road ASAP 👍
@@adjustmentinvestment9860 you might to change the throttle body but that’s not a guarantee that’ll work either 🤦🏽♂️, that would be the last thing that could be in fault including the air box… Maybe you have air leak in one of the pipes ?
I have issues with my 2004 k12. The windshield wipers are always on. Do you know anything about this? Sometimes they are off, but when it rains or snows they get back on automatically.
Yes this was happening to me last 2 years and it did it again and now its not starting at all it doesnt run anymore even if its cold Some people said that the crankshaft sensor does it to ? Or some of those sensors is 100% dead
very educated video. i have 2005 nissan micra 1.2 petrol the problem with the car is, its die or loos power while driving often...i have to switch off the ignition and start again to get it back and after some time same thing happen and I follow same procedure, my friend said uts electric problem but he don't know what electric problem could be..can you please guide me thank you.
Hi thank you for you kind comment, First of all have you tried putting it on diagnostic computer as this will pin point towards any sensors that are playing up or faulty. However if you cannot get it on a computer then the first thing I will do is try changing the coil packs & spark plugs (unless you’ve recently carried out a full service ?)
Hi, my 2007 k12 micra has issues with rough idle. Acceleration is very jumping and ride is very juddering. Rpm goes up intermittently. I’ve changed oil, filter, o2 sensor, and coil pack but still same issue? Do u think camshaft sensor would be something to try next???
As salaam a laykum, have you had the computer on the diagnostic computer? If so what codes has it come up with? As it’s not always the camshaft sensor that will need to be changed. JZK
@@zabzproject1416 w salam. When i got the car it didn’t had service for a while i think so i drove back from manchester to bradford on motorways and it was fine but as soon got off motorway it starts juddering and became quite jumpy acceleration. EML came on as well so I thought i might do service and it will be fine . I used obd 2 scan and p0123 and p0123 (p) codes came up. After oil change, filter , oxygen sensor we removed the code but juddering was still there. EML was gone. Yesterday i changed coil pack as well still no luck. Now i searched on google about p0123 code and it comes as throttle position sensor . But im cofused if it there is any difference between 3 sensors which are throttle body position sensor, camshaft sensor and crankshaft sensor and which one is on my car??? Because i feel like problem could be with one of them. Ps there’s no code on the computer now which makes it harder to pinpoint the issue
@@ghulammurtaza5843 that could be your TPS - Throttle Position Sensor, trying the following first: Check if the wiring is intact and not cut anywhere. See if the TPS is mounted properly (might have been replaced in the past as you’ve just got the car and don’t know the history of it) Try cleaning your throttle body (check my other UA-cam videos, I have a step by step guide on how to clean the throttle body with carb cleaner) If none of the above make a difference then I would recommend you changing the throttle body.
@@zabzproject1416 thanks. Just to clarify i was mentioning wrong code earlier, it wasnt p0123 it was actually p0132 (hence changed the oxygen sensor bank 1 sensor 1) just looked at old photos. Now reading up on internet I’ve heard people saying that even though code is for upstream/pre cat sensor but its good practice to change both sensors (pre and post cat) together 🥲. Anyway I give up. I’ll try maybe in couple of weeks when i can be arsed again
@@ghulammurtaza5843 hi yes it’s best to change both sensor, as sensor 2 could also be in fault hence why sensor 1 keeps showing faulty (they both communicate to each other so if sensor 2 is not replaced and sensor 1 is the fault still could be showing up after reset)
Asalamu alikum brother, fantastic video. My micra k12 has rough idle at neutral car doesn't stop but feels like it may stall. No codes but after few starts the problem goes away. What do you think? Then it comes back after few days.
Wa laykum as salaam If no codes are coming up you may want to try another diagnostic computer, for meanwhile you can try the following: 1st - clean the connectors on the wiring that connects to the sensor I.e. get an electric cleaner and spray it on the connectors (they might need cleaning) 2nd - the throttle body may need changing or cleaning with electrical cleaner, (do this by spraying the throttle body from both sides). Hope this helps 👍 Thanks for supporting our channel
@@zabzproject1416 one question though brother My mechanic has put new brake pads but when I show down grinding sounds come. He said brake disc had bad lip? Any suggestions
@@AbdurRahman-mb1vr as salaam a laykum We would suggest and recommend that you get your disc changed specially if it has a lip on, your mechanic should have advised you that when he was changing the pads as that would have saved you some money on labour 👍
Mashallah great video I have an Issue with my camshaft position sensor. I get code p0340 I got the connector cleaned (like 2 days ago) and it worked fine up and until now. However I still have the code on my dashboard I don't think that the mechanic had reset it. should it go away by its self or do I have to get it reseted with a scanner? also could you please tell me a good replacement brand for my car? (I mean a good brand that makes good camshaft position sensor) my car is a 2004 nissan micra k12 1.4L . with Kind regards Al salam aliukum. Moaz
Wa laykum as salaam, I would go to Nissan themselves and ask them if they have the sensor (I personally think OEM from manufacture is the best option & it shouldn’t be that expensive) Yes!!! The code will have to be reset (so try doing that first before you buy the sensor) Hope that helps 👍 JZK for supporting the channel.
I asked Nissan for the Sensor and they said its gonna be 105 euros (with out installing it... that's a bit too expensive the garage asked for 50 euros and I saw that I can get one from Autodoc for like 10/20 euros from a whole lot of different brands but I don't know which one is best)
@@moazdaza7275 have you tried Euro car parts? I’ve never tried Autodoc, so can’t really say which is a better brand.. Have a word with the customer service side & see if they can recommend a decent enough brand.. Changing the sensor is really easy only one 10mm bolt if you can do it yourself you’ll save a lot of money (just make sure you disconnect the battery) JZK
yes I'm planning on doing it my self and thank you for the battery advice I will make sure to do so. also on their application they do recommend 2 brands (recommended by their experts)
Assalam o Alikum Bro I have same problem of cam sensor problem change 2 times but same problem after Mecanic told change chain & garari spend 400£ after 2 weeks same engine sign & air bag sign both at the moment appear on dash car stop same& start in video as you share plz help me to solve my problems otherwise my car helth is good except this problem plz reply as possible. Jzk
@@waseemsarwarchaudhry8000 you need to get it on the diagnostic computer to get a code to indicate what the issue could be, on top of my head I would say check the wiring of the cam shaft sensor and make sure nothing has been cut and the plug is clicked in properly.. try to clean the plug with electric cleaner (this is after you change the sensor).
I can’t remember on top of my head what code we got, but that code ‘P1171’ would indicate towards vacuum leak.. so throttle body issue or leak from one of the vacuum pipes 👍
Are you sure the camshaft sensor plug is sitting in properly? Pls try to remove the plug and plug it in again, if this still doesn’t work then place the camshaft sensor bk and see if it will start up
@@zabzproject1416 Hi. thx for this video! I changed the sensor only 4 weeks ago, and now it seems that it have the same problem agai...car was running meanwhile 1500km, without any issue, correct behaviour...under 5L/km.. how is it possible that the sensor is f.u. again...strange
@@raimundweissenbacher4383 hi, are there any codes that come up on the diagnostic computer? There could be two other issues that you can look at; 1st - the wiring on the sensor I.e. get an electric cleaner and spray it on the connectors (they might need cleaning) 2nd - the throttle body may need changing or cleaning with electrical cleaner, (do this by spraying the throttle body from both sides). Hope this helps 👍 Thanks for supporting our channel.
@@zabzproject1416 Hi mate! thank u so much for this "super quick" response!!! The control light (motor symbol) is not activ...so I dont know, if there are any error-codes stored...don´t have a (good) OBD2 Tester...but tmrw I´ll check things you told me! I´ll report than...cheers
Thanks bro from France
Nice vedio
Thanks
Nice video I changed the camshaft position sensor on my Nissan march 2009 I changed every sensor but it's still start sometimes sometimes not if it's start it idle rough
Hi thanks,
Do any codes come up on the diagnostic computer?
The other common fault for such issue would be changing the complete throttle body including the air box, you can try cleaning just the throttle body (pls see my other videos as I show step by step guide how to clean the throttle body)
Hope this helps & hope you get your car sorted and bk on the road ASAP 👍
@@zabzproject1416 no there is no code coming up I tried diagnosed it
@@adjustmentinvestment9860 try to see if you can clean the throttle body first and see what happens 👍
@@zabzproject1416 I try clean it also nothing
@@adjustmentinvestment9860 you might to change the throttle body but that’s not a guarantee that’ll work either 🤦🏽♂️, that would be the last thing that could be in fault including the air box…
Maybe you have air leak in one of the pipes ?
I have issues with my 2004 k12. The windshield wipers are always on. Do you know anything about this? Sometimes they are off, but when it rains or snows they get back on automatically.
Yes this was happening to me last 2 years and it did it again and now its not starting at all it doesnt run anymore even if its cold
Some people said that the crankshaft sensor does it to ?
Or some of those sensors is 100% dead
Hi my micra is not starting I changed the sensors still and not sparking
Hi, can you advise me where you got the camshaft sensor from? Error code is po335
Hi you can buy it from Nissan / eBay.
Thanks 👍
very educated video. i have 2005 nissan micra 1.2 petrol the problem with the car is, its die or loos power while driving often...i have to switch off the ignition and start again to get it back and after some time same thing happen and I follow same procedure, my friend said uts electric problem but he don't know what electric problem could be..can you please guide me thank you.
Hi thank you for you kind comment,
First of all have you tried putting it on diagnostic computer as this will pin point towards any sensors that are playing up or faulty.
However if you cannot get it on a computer then the first thing I will do is try changing the coil packs & spark plugs (unless you’ve recently carried out a full service ?)
Hi, my 2007 k12 micra has issues with rough idle. Acceleration is very jumping and ride is very juddering. Rpm goes up intermittently. I’ve changed oil, filter, o2 sensor, and coil pack but still same issue? Do u think camshaft sensor would be something to try next???
As salaam a laykum, have you had the computer on the diagnostic computer? If so what codes has it come up with? As it’s not always the camshaft sensor that will need to be changed.
JZK
@@zabzproject1416 w salam.
When i got the car it didn’t had service for a while i think so i drove back from manchester to bradford on motorways and it was fine but as soon got off motorway it starts juddering and became quite jumpy acceleration. EML came on as well so I thought i might do service and it will be fine . I used obd 2 scan and p0123 and p0123 (p) codes came up. After oil change, filter , oxygen sensor we removed the code but juddering was still there. EML was gone. Yesterday i changed coil pack as well still no luck. Now i searched on google about p0123 code and it comes as throttle position sensor . But im cofused if it there is any difference between 3 sensors which are throttle body position sensor, camshaft sensor and crankshaft sensor and which one is on my car??? Because i feel like problem could be with one of them.
Ps there’s no code on the computer now which makes it harder to pinpoint the issue
@@ghulammurtaza5843 that could be your TPS - Throttle Position Sensor, trying the following first:
Check if the wiring is intact and not cut anywhere.
See if the TPS is mounted properly (might have been replaced in the past as you’ve just got the car and don’t know the history of it)
Try cleaning your throttle body (check my other UA-cam videos, I have a step by step guide on how to clean the throttle body with carb cleaner)
If none of the above make a difference then I would recommend you changing the throttle body.
@@zabzproject1416 thanks.
Just to clarify i was mentioning wrong code earlier, it wasnt p0123 it was actually p0132 (hence changed the oxygen sensor bank 1 sensor 1) just looked at old photos. Now reading up on internet I’ve heard people saying that even though code is for upstream/pre cat sensor but its good practice to change both sensors (pre and post cat) together 🥲.
Anyway I give up. I’ll try maybe in couple of weeks when i can be arsed again
@@ghulammurtaza5843 hi yes it’s best to change both sensor, as sensor 2 could also be in fault hence why sensor 1 keeps showing faulty (they both communicate to each other so if sensor 2 is not replaced and sensor 1 is the fault still could be showing up after reset)
Dear do u have a part number for me ? I have same problem
Thanks sir but we still have starting issues with k12 micra 1.2l 12 valve 2005 if you can help me pls do
Hi are their any codes that have come up?
Hello I like your video, I change the sensor 2 days ago but I have the same problem, can you help me?can I contact you?
Hi what code are you getting on the diagnostic computer, if you haven’t managed to put it on a diagnostic computer what’s the car doing ?
Thanks
@@zabzproject1416 hy , I didn’t know the diagnosis computer, can you look at my car?
Asalamu alikum brother, fantastic video. My micra k12 has rough idle at neutral car doesn't stop but feels like it may stall. No codes but after few starts the problem goes away. What do you think? Then it comes back after few days.
Wa laykum as salaam
If no codes are coming up you may want to try another diagnostic computer, for meanwhile you can try the following:
1st - clean the connectors on the wiring that connects to the sensor I.e. get an electric cleaner and spray it on the connectors (they might need cleaning)
2nd - the throttle body may need changing or cleaning with electrical cleaner, (do this by spraying the throttle body from both sides).
Hope this helps 👍
Thanks for supporting our channel
@@zabzproject1416 jaza kallah Khair brother iv changed the throttle body sensor on pedal and Alhamdu lillah so far everything is smooth
@@zabzproject1416 one question though brother
My mechanic has put new brake pads but when I show down grinding sounds come. He said brake disc had bad lip? Any suggestions
@@AbdurRahman-mb1vr as salaam a laykum
We would suggest and recommend that you get your disc changed specially if it has a lip on, your mechanic should have advised you that when he was changing the pads as that would have saved you some money on labour 👍
@@AbdurRahman-mb1vr alhumdulillah
GLOVES...are you doing dishes.
Mashallah great video I have an Issue with my camshaft position sensor. I get code p0340
I got the connector cleaned (like 2 days ago) and it worked fine up and until now.
However I still have the code on my dashboard I don't think that the mechanic had reset it. should it go away by its self or do I have to get it reseted with a scanner?
also could you please tell me a good replacement brand for my car? (I mean a good brand that makes good camshaft position sensor) my car is a 2004 nissan micra k12 1.4L .
with Kind regards Al salam aliukum.
Moaz
Wa laykum as salaam,
I would go to Nissan themselves and ask them if they have the sensor (I personally think OEM from manufacture is the best option & it shouldn’t be that expensive)
Yes!!! The code will have to be reset (so try doing that first before you buy the sensor)
Hope that helps 👍
JZK for supporting the channel.
I asked Nissan for the Sensor and they said its gonna be 105 euros (with out installing it... that's a bit too expensive the garage asked for 50 euros and I saw that I can get one from Autodoc for like 10/20 euros from a whole lot of different brands but I don't know which one is best)
@@moazdaza7275 have you tried Euro car parts?
I’ve never tried Autodoc, so can’t really say which is a better brand..
Have a word with the customer service side & see if they can recommend a decent enough brand..
Changing the sensor is really easy only one 10mm bolt if you can do it yourself you’ll save a lot of money (just make sure you disconnect the battery)
JZK
yes I'm planning on doing it my self and thank you for the battery advice I will make sure to do so.
also on their application they do recommend 2 brands (recommended by their experts)
@@moazdaza7275 brilliant 👍
All the best & we are always here to help, if you need anymore guidance pls don’t hesitate to message us 👍
Assalam o Alikum
Bro I have same problem of cam sensor problem change 2 times but same problem after Mecanic told change chain & garari spend 400£ after 2 weeks same engine sign & air bag sign both at the moment appear on dash car stop same& start in video as you share plz help me to solve my problems otherwise my car helth is good except this problem plz reply as possible. Jzk
Wa laykum as salaam,
What error code comes up when you put it on diagnostic computer?
@@zabzproject1416
Bro At the moment code no I don’t know but sure was came shafts sen which told me Mecanic
@@waseemsarwarchaudhry8000 you need to get it on the diagnostic computer to get a code to indicate what the issue could be, on top of my head I would say check the wiring of the cam shaft sensor and make sure nothing has been cut and the plug is clicked in properly.. try to clean the plug with electric cleaner (this is after you change the sensor).
@@zabzproject1416
Ok sir I will do and let you know if need will contact you InshaALLAH
@@waseemsarwarchaudhry8000
In shaa allah
It will get sorted.. if you need any help let us know
JZK
P1171 ????
I can’t remember on top of my head what code we got, but that code ‘P1171’ would indicate towards vacuum leak..
so throttle body issue or leak from one of the vacuum pipes 👍
My car had this problem, put the sensor, it won't start.
I Did like this and now my car does not snart, what could be wrong?
Are you saying you changed the camshaft sensor and after that it doesn’t start?
Are you sure the camshaft sensor plug is sitting in properly?
Pls try to remove the plug and plug it in again, if this still doesn’t work then place the camshaft sensor bk and see if it will start up
@@zabzproject1416 Hi. thx for this video! I changed the sensor only 4 weeks ago, and now it seems that it have the same problem agai...car was running meanwhile 1500km, without any issue, correct behaviour...under 5L/km..
how is it possible that the sensor is f.u. again...strange
@@raimundweissenbacher4383 hi, are there any codes that come up on the diagnostic computer?
There could be two other issues that you can look at;
1st - the wiring on the sensor I.e. get an electric cleaner and spray it on the connectors (they might need cleaning)
2nd - the throttle body may need changing or cleaning with electrical cleaner, (do this by spraying the throttle body from both sides).
Hope this helps 👍
Thanks for supporting our channel.
@@zabzproject1416 Hi mate! thank u so much for this "super quick" response!!!
The control light (motor symbol) is not activ...so I dont know, if there are any error-codes stored...don´t have a (good) OBD2 Tester...but tmrw I´ll check things you told me! I´ll report than...cheers