P2015 fix on Audi A4 with black plastic manifold (without removing intake manifold)

Поділитися
Вставка
  • Опубліковано 16 січ 2025

КОМЕНТАРІ • 86

  • @oleglvl
    @oleglvl 4 роки тому +12

    Thanks man! What a PAIN IN THE A** this was to fit it right on my car.... 2 hours I think. But engine light now cleared. Gold tutorial! All the best to you!

    • @technics6215
      @technics6215 3 роки тому +2

      Thats just 2 hours. Still better than manifold dismount and mount again. And no risk of high presshre fuel lines contamination and future injector and other problems.

  • @SteinArildGjestemoen
    @SteinArildGjestemoen Рік тому +3

    Greeting from Norway! Did this yesterday, my 2010 Audi TDI B8 had the P2015 fault. Followed the instructions here, and did the operation on less then 1 hour. Yes, it was tight, but straightforward. Be sure to put a rag around the working area, I missed the bracket in the engine bay, luckily I did find it on top of the gearbox... Used Vim HBR4 bit ratchet and a shortened bit. Fault code gone! Thanks for this useful video.

    • @simenhaugen1426
      @simenhaugen1426 Рік тому

      Hvor kjøpte du delene du trengte?

    • @dieselgeekdotcom
      @dieselgeekdotcom  Рік тому

      dieselgeek.com/products/p2015-code-repair-bracket-for-vw-cr-tdi-with-black-plastic-manifold-03l-129-711ag?_pos=1&_sid=ea6102555&_ss=r

  • @grahamshillingford8229
    @grahamshillingford8229 4 місяці тому

    My hat is off to you for trying to show what should be an easier method but I'm just gonna take my manifold off to do this. I took it off recently to clean it & it's still fresh in my memory. 👍

  • @fruchtquarkerdbeere
    @fruchtquarkerdbeere 4 роки тому +3

    Wow, works on my Passat B6 3C. But my motor was built in 180 degrees turned. It's very tricky! The Motor has to be completely cold. It works! After one hour and thirty minutes the work has done!
    Bei meinem Passat B6 3C hat es gut geklappt. Der Motor ist jedoch um 180grad gedreht eingebaut, was das herankommen an die besagte Stelle nicht leichter macht. Ich habe im Reparatursatz nur eine Kreuzschraube im Lieferumfang gehabt. Diese müsste ich durch eine inbusschraube ersetzen und auch einen passenden Bit kürzen. Nach gut 1,5 Stunden und vielen Schimpfwörtern habe ich es aber geschafft! Wichtig ist dass der Motor komplett kalt ist! Ich hab mir oft die Finger verbrannt!
    Nach der Arbeit ist der Fehler weg und bisher nicht wiedergekommen! Super! Danke für diese tolle Anleitung!

    • @technics6215
      @technics6215 3 роки тому

      I think you mean 90 degrees. I thought that it is easier in Passat for that reason...

    • @fruchtquarkerdbeere
      @fruchtquarkerdbeere 3 роки тому

      @@technics6215 No, i mean 180 degrees and there is nothing easier in Passat.

  • @christophriepl8163
    @christophriepl8163 5 років тому +4

    Greetings from Austria. Thank you for this wonderful useful video. I used a 6mm ring ratched with modified 1/4" bit. Pretty funny end of the video. "NOW YOU HAVE TO TIGHTEN THE SCREWS, AND THAT S IT." This ten seconds in video took me 1 1/2 hours. But anyway. All in all 800 € safed ~ 950 USD. Quote from the Audi service team. Not that easy but don't give up! Thank you guys!!!

  • @andytbaynes
    @andytbaynes 4 роки тому +5

    Fixed mine this way today ...used a 1/4 inch ring spanner instead of ratchet...used hot glue to hold the bit in the spanner

    • @Mynamemightbemichael
      @Mynamemightbemichael 3 роки тому +1

      Now that’s a good idea i will keep a hot glue gun in my tool box for that reason

  • @666markyboy
    @666markyboy Рік тому

    I gave up faffing about in the end and took the inlet manifold off , I've not long since had the entire head off so it was all fresh in my mind ..hour and half and job done and I happy knowing all is fitted correctly and securely, great video though

  • @urpourvelo7669
    @urpourvelo7669 5 років тому +4

    Bahco 2058/S26 is the perfect tool set for this job. Extremely small ratchet with all the necessary bits.

    • @uk42000
      @uk42000 4 роки тому

      Doing this now with the exact ratchet cut my tx30 down to the lines in the middle and its perfect

    • @flappye
      @flappye 3 роки тому

      do you still need to cut the bit or will it fit anyway?

    • @urpourvelo7669
      @urpourvelo7669 Рік тому

      @@flappye Yes. I cut 8 - 9 mm away and then it fits perfectly.

    • @fapseason
      @fapseason Рік тому

      Thanks for the video and thanks Urpo for this advice, just bought this set from Motonet. I have 2010 Golf with CBDB engine and seems that only have to remove couple of connectors and one vacuum hose to get enough room for installation. Tomorrow we will find out.

    • @fapseason
      @fapseason Рік тому

      Done, now when all steps are known could be done in 30 mins. Took about 2 hours total. Hard but not impossible.

  • @87kb1
    @87kb1 3 роки тому +1

    Thank you. Worked a treat on my 2010 2.0Tdi Passat. :)

  • @fulllaleks
    @fulllaleks 2 роки тому +1

    Thank you it's worked also for me on my Audi Q5 2.0 Phase1

  • @darylhurst1145
    @darylhurst1145 15 днів тому

    Man I don't know how you made this look so easy but after much swearing I just decided to take the manifold off and fit the bracket that way 😂

  • @J4rn0
    @J4rn0 11 місяців тому +1

    Thanks alot! saved me pulling the manifold :D

  • @alexandrumarius6772
    @alexandrumarius6772 4 роки тому +2

    Hello guys i had done the same job ,the Ratchet from Dewalt 1/4 it's perfect too for this work ,but there is a trick to install , if you don't pull up the arm nearly the screew then the bracket will not fit perfectly streight like in the video ,fill up with a lot of patience :)))

  • @cobrasteve427
    @cobrasteve427 2 роки тому +1

    Brilliant instructions!

  • @pcgrey69
    @pcgrey69 4 роки тому +1

    This really works
    You need to follow the instructions to the letter and you definitely need the tools that are listed.
    Not for the faint hearted as it's a really difficult fit but fingers crossed once the bracket is fitted the light will be sorted when reset. Thanks Diesel geek

    • @pcgrey69
      @pcgrey69 4 роки тому

      Codes cleared and engine light is now out. Used a mirror just to check the fitment but brilliant hack to rectify a poor design.

  • @АндрейАйпад
    @АндрейАйпад 3 роки тому +2

    Видео вдохновило не снимать коллектор, немного пришлось повозиться с откручиваем болта но все получилось

  • @technics6215
    @technics6215 3 роки тому +1

    Just one more question.
    In Audi CAHA with plastic manifold - is there any risk of flap detachment and sucking it into the engine causing huge engine problems, if I will use my car for few days after P2015 appeared? I'm asking because I have heard that in "some engines" , "some flap problems" can cause disaster because flap can detach.

  • @NWIE76
    @NWIE76 4 роки тому

    Brilliant video bro. Guna do that to my passat now. Cheers....

  • @oneeetwooooothreeee
    @oneeetwooooothreeee 3 роки тому +1

    Thanks for helping us. I have little question if possible. I was getting p2015 and installed bracket. It is 2.0 TDI CR with plastic intake manifold. Mechanic needed to take away manifold to install bracket, he disconnected fuel lines from high pressure fuel pump because they were covering intake manifold. Anyway, long story short, no more p2015 but after this engine started to work louder, after few days i noticed he did not tightened fuel line bolt from high pressure fuel pump to rail and the fuel was leaking under high pressure fuel pump, including revving up on idle to compensate for the pressure i guess. I visited mechanic once again and he fixed this by tightening the screw but engine still works louder along the vibrations on idle, no revving on idle anymore. Is it possible that 'ecu/computer' needs to learn new settings while driving, or there is 'air' in fuel lines? is it possible that he damaged hpfp because he did not tightened fuel line from hpfp to rail? or something else? thanks a lot to anyone having time to help me out

  • @flint0107
    @flint0107 Рік тому

    Compliments. Very interesting and thanks for sharing. Is the intervention on A4 model B9? Tdi or Tfsi? Thank you and good week end

    • @dieselgeekdotcom
      @dieselgeekdotcom  Рік тому

      TDI w plastic manifold ending in 711AG

    • @flint0107
      @flint0107 Рік тому

      @@dieselgeekdotcom okay. thanks for the information. Are you aware if the issue happens on tfsi 2.0 on A4 B9 model year 2019?

  • @Pulaksa
    @Pulaksa 5 років тому +9

    Thank you. It worked. But those two hours were just miserable 😄

    • @NWIE76
      @NWIE76 4 роки тому +1

      Lol less miserable than removing the manifolt to attach the dieselgeeks part I hope as that's what I'm looking at doing to my 09 passat in the nxt week or two!!! Respect.

    • @d3t4ix32
      @d3t4ix32 4 роки тому +1

      @@NWIE76 nah. I removed the whole thing and it wasnt hard at all

  • @Jack-ns5zc
    @Jack-ns5zc Місяць тому

    Whats the purpose of the bracket. Does it stock the arm travelling too far??

    • @dieselgeekdotcom
      @dieselgeekdotcom  Місяць тому

      Yep, that's how it works in a nut shell

    • @Jack-ns5zc
      @Jack-ns5zc Місяць тому

      @ i see, i assume the fault with it is it goes to far doesnt return properly. I have this fault but i just wanted to understand what the bracket is for

    • @dieselgeekdotcom
      @dieselgeekdotcom  Місяць тому

      @Jack-ns5zc correct

  • @MGrims
    @MGrims 5 років тому +2

    Used a combination wrench and a cut torx bit for this which took the guts of an hour. Buy the recommended tool if you want to save yourself a lot of pain haha. Also after I got the bracket installed, the engine light remained. Heartbreaking
    Update:
    Managed to get it working. I had to depress the actuator first and install the bracket with it depressed.

    • @MGrims
      @MGrims 5 років тому

      Great video however and well explained.

    • @uk42000
      @uk42000 4 роки тому +1

      How do you depress the actuator bud

    • @87kb1
      @87kb1 4 роки тому

      @@MGrims How did you depress the actuator?

  • @henrikbach9475
    @henrikbach9475 11 місяців тому

    Hi
    I was wondering if theres a solution to the same problem on the 04L129709C manifold on a VW transporter T6, 2018?
    Can’t find a bracket for that manifold anywhere! 😞

  • @-robster-robster-
    @-robster-robster- Рік тому

    have you never heard of slipping a 7mm spanner over the bare torx bit? thats what i did no need for ratchets

  • @RenoOnlyOneRaines
    @RenoOnlyOneRaines 4 місяці тому

    hello, is it necessary to practice an adaptation of the engine of the intake pipes with VCDS after having added the metal part? thank you in advance

  • @davidhirschmann1016
    @davidhirschmann1016 2 роки тому

    It works! Thanks! :)

  • @julianbusters4359
    @julianbusters4359 5 років тому

    Thank you bro for the vid👍🏻👍🏻👍🏻

  • @irishRocker1
    @irishRocker1 3 роки тому

    EDIT: Just wanted to also mention that i like how your bracket has a slot so that the screw doesnt have to be completely removed. Other brackets have a whole so screw has to be fully removed so might be a little more difficult.
    Couldnt you just use the torx bit and insert it into the torx screw and grip it with a pliers to loosen it?
    Also, if i did this and decided to loosen all 3 screws to remove the sensor and open it up for a clean is it difficult to get it out?

    • @irishRocker1
      @irishRocker1 3 роки тому +1

      @@dieselgeekdotcom Yes I understand. By gripping the torque bit you would have to move very tiny amounts repeatedly, if it can even turn enough to allow to remove, reset, repeat. I ordered Bosch 2607017160. It looks similar size to the zebra but is £16 vs £85. I will try it and if it works, great. If it doesn't work, it will be useful to have anyway for cheap price and I will bring to a garage. If I spend £85 for a mini ratchet it is probably better to pay that money to a professional to do it. Thank you for your help!

    • @irishRocker1
      @irishRocker1 3 роки тому +1

      @@dieselgeekdotcom Thanks so much to you and Sali for the video. I finally completed the installation yesterday. It was a pain! very awkward job and could not have done it without this video. I used Bosch 2607017160. I tried changing the latch direction with a screwdriver but that was a bad idea. It lifted the lever and would not ratchet properly in either direction so worried I had just embedded it in the engine but was able to press the lever back in with a screw driver and it worked properly again. There is room to flip the lever with your fingers so hopefully nobody else makes my mistake. Also, when i started it up there was about 5-6 error codes with fuel sensor stuff etc. It's because a lot of the connectors were disconnected and so on, but it was running and once cleared, it's been clear since yesterday. So if anyone sees additional fault codes, don't panic. Probably would have cleared the faults itself eventually

  • @tpulse2001
    @tpulse2001 4 роки тому

    is it possible to replace the spring as well when doing this way??

  • @TalhaMalik89
    @TalhaMalik89 5 років тому

    There are two types of brackets in your store, are both usable on this same model or do i have to specifically order this one?

    • @123romass
      @123romass 4 роки тому

      @@dieselgeekdotcom hello. Can you send information where you buy this aluminium kit?

  • @markjames6099
    @markjames6099 3 роки тому

    Yes, it does work and it is a pain in the a**. A 6mm bi-hex ring spanner and a T30 bit works just as well as the ratchet. To get as much operating space as possible and to make sure that the bracket is in the right place, you should pull the arm up out the way with a long cable tie. Once done, the engine management system will take some time to reset itself and for the engine management warning light to go off. I thought I had failed only to find that the next morning I started the engine, the management light was off. Good luck!!

  • @RenoOnlyOneRaines
    @RenoOnlyOneRaines 4 місяці тому

    Thx u

  • @tomnelson4660
    @tomnelson4660 3 місяці тому

    Does anyone have a link to the correct part. I know the plastic manifolds are different to the ally ones,
    Thanks.

    • @dieselgeekdotcom
      @dieselgeekdotcom  3 місяці тому

      dieselgeek.com/products/p2015-code-repair-bracket-for-vw-cr-tdi-with-black-plastic-manifold-03l-129-711ag?_pos=1&_sid=acf1b4f43&_ss=r

  • @Leezy-ic7kp
    @Leezy-ic7kp 3 роки тому

    So what year is the car

  • @Stigman101
    @Stigman101 3 роки тому

    hi just done mine not too bad got bit of ebay £10 small bahco ratchet cut down 30 spline bit all good

  • @whiskeybluez
    @whiskeybluez 4 роки тому

    Hey mate can see the engine on this audi is east west. I have passat with 2.0 tdi north south engine. Will this procedure work?

    • @whiskeybluez
      @whiskeybluez 4 роки тому

      @@dieselgeekdotcom thanks I do. You mentioned that you need to slide the thing when fitting it, any tricks there as you haven't covered in the video?
      Is delivery time same durring COVID-19? I'm in Australia

  • @michaeltaylor1553
    @michaeltaylor1553 3 роки тому

    Is it ok to drive the car with this fault

  • @1ShaunyC
    @1ShaunyC 5 років тому

    Jst had this fault code come up on my vw tiguan tdi... Would this work for that?? And what actually does this do to rectify the fault?
    Thanx

    • @1ShaunyC
      @1ShaunyC 5 років тому +1

      @@dieselgeekdotcom thank you...

  • @123romass
    @123romass 4 роки тому

    Hello. Can you writh for my, where you buy this aluminium kit? I don’t find the same. 🙏

    • @123romass
      @123romass 4 роки тому

      Thanks mean 👍

    • @jimmyoberg3804
      @jimmyoberg3804 Рік тому

      Where can i buy that bracket?

    • @dieselgeekdotcom
      @dieselgeekdotcom  Рік тому

      dieselgeek.com/products/p2015-code-repair-bracket-for-vw-cr-tdi-with-black-plastic-manifold-03l-129-711ag?_pos=1&_sid=dd0a5f710&_ss=r

  • @Yelowbuddy
    @Yelowbuddy Рік тому

    Ze Germans don't wan't to buy new intake manifold?😛Thanks a lot for insightfull tutorial man.

  • @dstackz3190
    @dstackz3190 2 роки тому

    Will this work with 1.8 T

  • @KjH-sq1sz
    @KjH-sq1sz Рік тому +1

    It's easier to just remove the manifold, I removed mine today and took around 30 minutes.

    • @sipapito
      @sipapito Місяць тому +1

      Do you have a video on how to?

  • @rdawgin
    @rdawgin 5 років тому

    Would this work on a Golf gti?

  • @technics6215
    @technics6215 3 роки тому

    I want to try without rachet. What do you think about bending screwdriver-like Torx? T30 is pretty thick, but maybe it is possible to bend it properly after heating with propane torch.

  • @mikeg3536
    @mikeg3536 3 роки тому +1

    After this "fix" the following error will appear : P2009 means the intake manifold runner control circuit has excessively low voltage for bank 1 . This happen because you block the because after applying the limiter, the flap no longer makes its way and burns. Which will inevitably result in a change in the throttle valve

  • @iceboxco3308
    @iceboxco3308 3 роки тому

    hi, my engine light on my audi a4 b8 avant is on and audi said that the Intake manifold should be exchanged and noted code (G513) , is this code same as p2015? and would this was solve my problem and get the engine light to turn off ?
    i would appreciate your answer sooo much.