Dude, you are honestly a lifesaver!!! My pulley broke right off the bracket. Bought everything you said...works perfectly now! Super cheap repair, thanks to you!!!!
Dude, dude! DUUUUUUUDE!!! you saved me so much time and money. Totally helped! DUUUUUUUUUUDE!!!! 1 year later and it still works... the other pulley went down so came back here to remember how to fix it. Again, life saver.
After cutting & grinding off the bent bolt, I did this fix using JD parts. As another poster indicated, there's a bushing that fits the JD idler. There's also a 10mm bolt & cap lock that is a perfect fit inside the bushing, and is used in other applications of the pulley. Easy replacement with these parts once you get the offending welded bolt cut off the bracket. Parts list: Idler: GY22082. ($13) Bushing: M71682. ($5) M10 Flangelock: 14M7400. ($2) M10x40: 19M7804. ($3) M10 5x30 washer (2): 24M7178. ($1.50)
This looks perfect, thank you. I was lucky/unlucky enough that the entire bolt broke out where it attaches into the bracket, but that almost makes it easier.
Purchased this to replace a guide pulley ua-cam.com/users/postUgkxO9seYZjlnuP5UvMkb7osQW3WxPVeSnPk on our John Deere x304 snowblower. As I stated in the title, it is just about perfect. The stock pulley has a spacer at the bottom. I used four washers to emulate said spacer, and it works perfectly now. Great product, and great price especially if compared to typical JD prices.
great video...I had similar problem on my JD mower deck. I used what I had at the time I put a 2" 3/8 bolt in the hole from the welded bolt from underneath with washers and found that lock washers fit where the bushing should be and used 3 of them for the spacer, then topped with another washer, lock washer and nut, so far so good!
Thanks. This happened to our mower the other day and we were stumped as to what to do. My husband just cut the bolt off with a hacksaw. He is having some ice cream as a much deserved reward.
We wound up going a slightly different route. We used four 3/8"id Lock washers and gently tapped them inside the center of the new idler pulley. It made for a snug fit for the 3/8" bolt. The hardest part was getting the nut on the threads as I was trying to do it blind. My husband son got the mower deck reattached to the tractor this afternoon. It is a lot quieter and is cutting much better than before. I'm surprised it cut at all before the pulley flew off as the bearings were completely melted. It's doing great now. Than you so much for this video!
You sir are an inspiration. Great video! I love it when we don't accept that we have to spend large amounts of money for something because we are in a bind. all the while planning in our mind what will work. I think we all should learn how to fix everything that we own to the best of our ability. Keep up the good work......you are awesome! Thank you for sharing your knowledge
Fixed mine today, found a real thick washer and welded it to the shaft and to the bracket to make the whole thing one, as it had bent a few times before. heavy duty now!
I had the exact same thing happen to me! I was looking and looking online and couldn’t find anything until I found this video! You’re a total life saver man! It works great! I did everything step by step and I’m up and mowing again! Thank YOU!
I did a similar fix for another JD deck. Except I replaced the fuel hose with an 11mm (1/2" drive) socket. Fitted perfectly to the bearing and provided the height off the bracket. If you haven't got an old socket they can be bought loose for about $1.
Thanks for this. A friend of mine had this exact failure on his l110 mower deck. He asked me to help him fix it and everyone was saying it couldn't be done as I was saying it could. This shut them up.
Eddie Lambert, How is it working so far? (I notice it has been three months since your comment!) I have had this very same thing happen just *today* , and am about to proceed to this "fix"...... Thanks!
To replicate the tower stud, cut it off without damaging the bracket. Then get JD Part# M71682 bushing (as another poster said), Metric Bolt Grade 8.8 M10x1.50 2 1/2 inches long and a locking nut to fit the bolt. Maybe a washer or two. The bushing can be obtained at your local JD dealership for about $4. The nut, washers and bolt can be had at any good hardware store or just get them when you get the bushing.
I appreciate this video, very resourceful fix, but I would be concerned that the rubber hose "bushing" may break down under the belt induced forces and harsh environment. Would be interesting to know how it held up. No worries with a metal bushing, thanks for the part number.
I appreciate this useful post with the parts list. My bolt sheared off and so I cut the rest of the bolt off with my angle grinder. It was an easy fix after sourcing the parts from the local JD dealer. I could have gotten the nuts and bolts from the Depot for cheaper,but that pulley hub versus using washers just made it simpler to order everything from the JD website.
I did something very similar but I used a grade 8 5/8" bolt It fit almost snug to the inside of the bearing and I used JB Weld to fill the 1/32" gap So that the bearings spun freely.
I fixed mine in a similar way, I used some bearing and steel spacers with some washers and I got the deck to work great. this video helped ALOT!! thank you. John Deere will tell you you may need a new deck for 600$+ DO NOT BUY THE NEW DECK
Thanks so much for the information… My pulley was broken but my boat was intact but was only spinning. Will be following your directions now after getting the bolt off. Thanks again
thats exactly what I have in front of me! My bolt is spinning so I cant get the nut off. I tried double nutting so I could hold the spinning bolt but there isnt enough length. How did you make out with your repair?
bolt was loose, pry bar or large screwdriver to bend frame back, used epoxy mix, which I put into and around loose bolt using JBweld , put 1 thicker washer down onto weld more weld and guide back on , still using it, quick fix until I can weld it, let sit for a day and it is solid.
My idler looks " cocked up" musta got bent somehow, I suppose the bolt bent. I'm cleaning / fixing up mower now. I'll keep this in mind for sure. Thanks
Mine too. My efforts with going from the top down approach didn't workout so well. I'm not sure if these bearings are supposed to be squeezed this way. Some are sensitive to the side pressure is on. I wonder how this has worked out for him using the hose. Mine was red hot in the very center inside race.
That same pulley on mine is leaning forward a little so it's not perpendicular. I have a vibration in the deck when I engage the blades, I'm wondering if that leaning Idler Pulley could cause that? I have replaced both Idler Pulleys and belt, still vibrates. seems worse when deck cutting height is set higher.
Thanks I got her figured out and she’s mowing now! This mower had sat up for 2 years, with gas still in the system. So she took a bit of work but she’s running like a dream now.
Thanks for this. I've not yet applied the fix. I have to get the motivation to go out and get the parts. I foolishly believed that John Deere wouldn't have welded the bolt on. It's an idler pulley that would have a shear force on it, so I naturally assumed that such a thing would be easily replaceable. I guess that's why I'm not an engineer.
There should be a hole. You may have ground the bottom of the bolt into the bracket. You may be able either pop it out of drill it out. If not, you would need to drill a hole.
Question to the pulley covers hold the back of the belt from falling off when blade is disengaged? I bought a new belt and testing it keeps coming off. Don't know if I got a bum belt or what.
What was the idler pulley part number on Amazon i have a John deere lt180 lawnmower with a 48 inch deck .I'm having trouble finding the same idler but for a lt180 john deere with a 48 inch deck
Smae thing happened to my la115 but it looks like i caught it in time before the bolt/stud got messed up beyond use. It did wear into it slightly so i'm crossing my fingers it will be ok. if not i will try welding up the wore spot and grinding/filing it back to shape. If all fails i will use the method you came up with or one of the one's shared i the post. I'll know more when the pulley arrives. Thank you for the information. ::SUBBED::
I see you did this about 9 months ago. I'm curious to know how this held up. My concern is that with the vibrations of running the mower the stop nut may work its way loose. Do you check it before you mow, or has it held tight so far? This is a great alternative to welding or getting the repair kit. Definitely going to save some money if it holds up.
@@TheCchilly It is *THREE YEARS* later, so is this "fix" still holding? This very *same* thing happened to me today. The thing went flying across the yard, and the entire bolt bent sideways....... Thanks for your video because *THIS* is the fix I am going to use!
@@TheCchillythe bolts a 3/8’s? I have a 48” mower deck and I messed up got a 9/16 bolts. Which I miss heard ya.but this is greet I’m fixing my deck today
La145 is the same and uses the same parts as all the 100 series big box store Deere tractors. For this issue, look up part # M71682. Can be found on Amazon for 10$, put a bolt through it and get back to mowing. This is a simple do it your self repair. If your lucky, it will just need the mounting bolt bent back into position and welded. Check out my videos for info on that.
Kade. I bought a bolt at local hardware store. The suggestion of buying the part and welding is good IF you can weld. My fix was for the average handyman.
@@GTObearclaw1 having something welded in your own yard or home is an easy fix?? How many average Joes are setup with a welding shop next to the kids bicycle and squirt gun?
@@donschlonski2936 You'd be surprised how many people have welders in their garage, or know someone who does. Worse come to it, use two batteries. It is NOT rocket science.
This one? Mower Deck Small Idler Pulley for John Deere D100 D110 D130 D140 Replaces GY22172 www.amazon.com/dp/B07FYXXBC9/ref=cm_sw_r_cp_api_i_QYW5CbGVCFQVF
@@annasullivan4719 Hi Anna, was that the very one? Very *SAME* thing happened to me today ~~ this seems to be a very common issue, huh? *WOW* It is *ALWAYS* something. The bolt on mine also bent sideways....... WOW
brendan t This is the one I bought and it worked like a charm and still is! MaxPower 10741 Flat Idler Replaces John Deere GY20067, GY22172 www.amazon.com/dp/B001OK8M50/ref=cm_sw_r_cp_api_i_gvWuDb8AS7KFC
Looks like a good rig, I have the LA 110 and it's a pos. Wait till your deck mounts start to crack around the welds on these tinny decks. I should of bought something else these things are cheaply made with china parts.
@@jimy4real666 yeah I welded in aftermarket spindle support rings really helped out with the cracking. The idlers pulley with the perch is pulling out now had to put a bar under the perch to keep it in place.
Dude, you are honestly a lifesaver!!! My pulley broke right off the bracket. Bought everything you said...works perfectly now! Super cheap repair, thanks to you!!!!
Dude, dude! DUUUUUUUDE!!! you saved me so much time and money. Totally helped!
DUUUUUUUUUUDE!!!! 1 year later and it still works... the other pulley went down so came back here to remember how to fix it. Again, life saver.
After cutting & grinding off the bent bolt, I did this fix using JD parts. As another poster indicated, there's a bushing that fits the JD idler. There's also a 10mm bolt & cap lock that is a perfect fit inside the bushing, and is used in other applications of the pulley. Easy replacement with these parts once you get the offending welded bolt cut off the bracket.
Parts list:
Idler: GY22082. ($13)
Bushing: M71682. ($5)
M10 Flangelock: 14M7400. ($2)
M10x40: 19M7804. ($3)
M10 5x30 washer (2): 24M7178. ($1.50)
Is there a video of this fix being done??
This looks perfect, thank you. I was lucky/unlucky enough that the entire bolt broke out where it attaches into the bracket, but that almost makes it easier.
Thank you so much for this hack! Replicated exactly what you did, and we'll be trying it out tomorrow! Should work like a champ..... Thanks again
Thanks for all info, ordered, fingers crossed
July 2024.
The part numbers are correct. I got them through a john deere dealer in Lee's Summit, Missouri.
$15 for everything. Easy fix.
Purchased this to replace a guide pulley ua-cam.com/users/postUgkxO9seYZjlnuP5UvMkb7osQW3WxPVeSnPk on our John Deere x304 snowblower. As I stated in the title, it is just about perfect. The stock pulley has a spacer at the bottom. I used four washers to emulate said spacer, and it works perfectly now. Great product, and great price especially if compared to typical JD prices.
great video...I had similar problem on my JD mower deck. I used what I had at the time I put a 2" 3/8 bolt in the hole from the welded bolt from underneath with washers and found that lock washers fit where the bushing should be and used 3 of them for the spacer, then topped with another washer, lock washer and nut, so far so good!
Can't thank you enough! Saved me $168 for a new bracket! So far its working great, confident it is fixed for good! Many thanks my friend!
Thanks. This happened to our mower the other day and we were stumped as to what to do. My husband just cut the bolt off with a hacksaw. He is having some ice cream as a much deserved reward.
We wound up going a slightly different route. We used four 3/8"id Lock washers and gently tapped them inside the center of the new idler pulley. It made for a snug fit for the 3/8" bolt. The hardest part was getting the nut on the threads as I was trying to do it blind. My husband son got the mower deck reattached to the tractor this afternoon. It is a lot quieter and is cutting much better than before. I'm surprised it cut at all before the pulley flew off as the bearings were completely melted. It's doing great now. Than you so much for this video!
You sir are an inspiration. Great video! I love it when we don't accept that we have to spend large amounts of money for something because we are in a bind. all the while planning in our mind what will work. I think we all should learn how to fix everything that we own to the best of our ability. Keep up the good work......you are awesome! Thank you for sharing your knowledge
Fixed mine today, found a real thick washer and welded it to the shaft and to the bracket to make the whole thing one, as it had bent a few times before. heavy duty now!
I had the exact same thing happen to me! I was looking and looking online and couldn’t find anything until I found this video!
You’re a total life saver man! It works great! I did everything step by step and I’m up and mowing again! Thank YOU!
I did a similar fix for another JD deck. Except I replaced the fuel hose with an 11mm (1/2" drive) socket. Fitted perfectly to the bearing and provided the height off the bracket. If you haven't got an old socket they can be bought loose for about $1.
@Fletcher Giovanni definitely, I've been watching on flixzone} for years myself :)
@Fletcher Giovanni Yup, have been watching on flixzone} for months myself =)
Great idea think that would hold up better than hose.. I'm in same boat ..bolt pulley sheared off
Ty 4 this video, your replies over the years & all comments...
Thanks for this. A friend of mine had this exact failure on his l110 mower deck. He asked me to help him fix it and everyone was saying it couldn't be done as I was saying it could. This shut them up.
Clear, concise, good diction, good video. This should help us get ‘ER done.
I had this exact problem and followed these directions and it worked perfectly.
Eddie Lambert,
How is it working so far? (I notice it has been three months since your comment!) I have had this very same thing happen just *today* , and am about to proceed to this "fix"...... Thanks!
To replicate the tower stud, cut it off without damaging the bracket. Then get JD Part# M71682 bushing (as another poster said), Metric Bolt Grade 8.8 M10x1.50 2 1/2 inches long and a locking nut to fit the bolt. Maybe a washer or two. The bushing can be obtained at your local JD dealership for about $4. The nut, washers and bolt can be had at any good hardware store or just get them when you get the bushing.
Thanks much! I am sending my buddy to the store to get this stuff, he had the same thing break.
I appreciate this video, very resourceful fix, but I would be concerned that the rubber hose "bushing" may break down under the belt induced forces and harsh environment. Would be interesting to know how it held up. No worries with a metal bushing, thanks for the part number.
u da man
I appreciate this useful post with the parts list.
My bolt sheared off and so I cut the rest of the bolt off with my angle grinder.
It was an easy fix after sourcing the parts from the local JD dealer.
I could have gotten the nuts and bolts from the Depot for cheaper,but that pulley hub versus using washers just made it simpler to order everything from the JD website.
This pulley comes with a separate shoulder: Looks like it would work ---> "STENS 280-164 John Deere AM37249"
Thanks, man! Exactly the kind of fix I needed. I had to drill mine out, still plugging away at it
I did something very similar but I used a grade 8 5/8" bolt It fit almost snug to the inside of the bearing and I used JB Weld to fill the 1/32" gap So that the bearings spun freely.
I just tried this. Went together easy enough. Hopefully it holds up. Thanks for posting !
did it ?
I just completed this repair as described. Works like a dream.
I fixed mine in a similar way, I used some bearing and steel spacers with some washers and I got the deck to work great. this video helped ALOT!! thank you. John Deere will tell you you may need a new deck for 600$+ DO NOT BUY THE NEW DECK
Best video iv seen for this fix works great
Thanks so much for the information… My pulley was broken but my boat was intact but was only spinning. Will be following your directions now after getting the bolt off. Thanks again
thats exactly what I have in front of me! My bolt is spinning so I cant get the nut off. I tried double nutting so I could hold the spinning bolt but there isnt enough length. How did you make out with your repair?
Glad I found you. I cannot for the life of me lift that pulley up so I can put the new belt on
My bolt is bent I will be giving this a shot thank you for the post😀👍 great fix!!
Thanks for the video, had the same problem and you just saved me 70 bucks.
Can’t believe this worked. Great stuff. Thank you!
bolt was loose, pry bar or large screwdriver to bend frame back, used epoxy mix, which I put into and around loose bolt using JBweld , put 1 thicker washer down onto weld more weld and guide back on , still using it, quick fix until I can weld it, let sit for a day and it is solid.
Excellent video and extremely helpful. Going through the exact issue with my LA130
Very true problem, the part number from John Deere is M 71682.
Cut the old part off and put the new part on $4.26.
My idler looks " cocked up" musta got bent somehow, I suppose the bolt bent. I'm cleaning / fixing up mower now. I'll keep this in mind for sure. Thanks
Thanks. The weld that held the bolt on broke on mine.
Mine too. My efforts with going from the top down approach didn't workout so well. I'm not sure if these bearings are supposed to be squeezed this way. Some are sensitive to the side pressure is on. I wonder how this has worked out for him using the hose. Mine was red hot in the very center inside race.
Thanks for the video, it's appreciated.
Nice job sir.
Great idea with the hose.
That same pulley on mine is leaning forward a little so it's not perpendicular. I have a vibration in the deck when I engage the blades, I'm wondering if that leaning Idler Pulley could cause that? I have replaced both Idler Pulleys and belt, still vibrates. seems worse when deck cutting height is set higher.
Can you list the parts that you bought?
Great video worked perfect thanks
This pulley comes with a separate shoulder: Looks like it would work ---> "STENS 280-164 John Deere AM37249"
do you have a list of pieces i need for this repair
How or what did you use to cut the bolt off?
I used a dremmel tool but I’m sure a small angle grinder or hacksaw would work as well.
Genius fix! Do you still check this? I’ve got a problem with my mower deck and looking for advice
Tough Tool Reviews thanks! I do check occasionally. Not sure I can help but will try.
Thanks I got her figured out and she’s mowing now! This mower had sat up for 2 years, with gas still in the system. So she took a bit of work but she’s running like a dream now.
Thanks for this. I've not yet applied the fix. I have to get the motivation to go out and get the parts.
I foolishly believed that John Deere wouldn't have welded the bolt on. It's an idler pulley that would have a shear force on it, so I naturally assumed that such a thing would be easily replaceable. I guess that's why I'm not an engineer.
Well I'm glad to know I'm not the only one thoroughly disappointed with my la 115. HUGE POS like the boob luver
I took a grinder and took of the bolt. But now the entire surface is flat with nowhere for. Bolt. Do I need to drill a new hole?
There should be a hole. You may have ground the bottom of the bolt into the bracket. You may be able either pop it out of drill it out. If not, you would need to drill a hole.
Question to the pulley covers hold the back of the belt from falling off when blade is disengaged? I bought a new belt and testing it keeps coming off. Don't know if I got a bum belt or what.
Yeah, the covers and tension should hold it on. You may have gotten too big of a belt. Even disengaged, the belt should have tension.
@@TheCchillythx
What was the idler pulley part number on Amazon i have a John deere lt180 lawnmower with a 48 inch deck .I'm having trouble finding the same idler but for a lt180 john deere with a 48 inch deck
Here is what I ordered. Stens 280-242 Heavy Duty Flat Idler
So did the repair last? I have the same issue.
Yup. No issues at all.
Smae thing happened to my la115 but it looks like i caught it in time before the bolt/stud got messed up beyond use. It did wear into it slightly so i'm crossing my fingers it will be ok. if not i will try welding up the wore spot and grinding/filing it back to shape. If all fails i will use the method you came up with or one of the one's shared i the post. I'll know more when the pulley arrives.
Thank you for the information.
::SUBBED::
Wouldn't that fuel line hose get hot and worn in time and you have another mess?
Hasn't in 8 years. Still going...for now.
What website did you get it I need a hydraulic pulley for a 115 series
I see you did this about 9 months ago. I'm curious to know how this held up. My concern is that with the vibrations of running the mower the stop nut may work its way loose. Do you check it before you mow, or has it held tight so far? This is a great alternative to welding or getting the repair kit. Definitely going to save some money if it holds up.
Sorry this post just popped up. It has held up. Haven't checked the bolt abut will do so this eve before I mow.
@@TheCchilly It is *THREE YEARS* later, so is this "fix" still holding? This very *same* thing happened to me today. The thing went flying across the yard, and the entire bolt bent sideways.......
Thanks for your video because *THIS* is the fix I am going to use!
brendan t - It’s still “fixed”. Kinda surprised but thankful that it is.
@@TheCchillythe bolts a 3/8’s? I have a 48” mower deck and I messed up got a 9/16 bolts. Which I miss heard ya.but this is greet I’m fixing my deck today
So stupid Question. I have a similar issues the the flat idler shaft on the 48". why not just replace it with a Shoulder bolt....
Thank you thank you thank you!!
Where can I find the Mount or bolt for sale online? I have searched and can not find it anywhere for a LA145 or any mower deck for that means.
La145 is the same and uses the same parts as all the 100 series big box store Deere tractors. For this issue, look up part # M71682. Can be found on Amazon for 10$, put a bolt through it and get back to mowing. This is a simple do it your self repair. If your lucky, it will just need the mounting bolt bent back into position and welded. Check out my videos for info on that.
Kade. I bought a bolt at local hardware store. The suggestion of buying the part and welding is good IF you can weld. My fix was for the average handyman.
@@GTObearclaw1 having something welded in your own yard or home is an easy fix?? How many average Joes are setup with a welding shop next to the kids bicycle and squirt gun?
Don Schlonski carry it down to the muffler shop with part in hand. Pay 10$ bucks and blam. Or get a welder from Home Depot.
@@donschlonski2936 You'd be surprised how many people have welders in their garage, or know someone who does. Worse come to it, use two batteries. It is NOT rocket science.
How long would you expect this to last before you have to redo it?
W C Bailey not sure but my fix is still working.
@@TheCchilly So, 4 years later and still going strong! Answered my previous post/reply wondering if the rubber hose bushing would hold up.
This literally just happened to me. 🤦♀️ where do I get the new pulley?
Anna Sullivan pretty sure I got mine on amazon.
This one?
Mower Deck Small Idler Pulley for John Deere D100 D110 D130 D140 Replaces GY22172 www.amazon.com/dp/B07FYXXBC9/ref=cm_sw_r_cp_api_i_QYW5CbGVCFQVF
@@annasullivan4719 Hi Anna, was that the very one? Very *SAME* thing happened to me today ~~ this seems to be a very common issue, huh? *WOW*
It is *ALWAYS* something. The bolt on mine also bent sideways....... WOW
brendan t This is the one I bought and it worked like a charm and still is!
MaxPower 10741 Flat Idler Replaces John Deere GY20067, GY22172 www.amazon.com/dp/B001OK8M50/ref=cm_sw_r_cp_api_i_gvWuDb8AS7KFC
How do you remove the original bolt?
i used a small angle grinder. A dremmel or something like that would work.
I used a multi tool with a carbide blade. Took awhile but it worked.
That's exactly what happened to my idler...how did you cut the bolt off? Thanks for the video.
I use a dremmel. A angle grinder would be best tho. Dremmel was under powered.
+Chad Childress....hey thanks for figuring this out...I just fixed it using your video! Again thanks!
+Aurelio Cazares 👍🏼
Aurelio Cazares
Thank you so much
thanks so much
The lesson here…….they make a horrible noise in plenty of time to change up before this happens.
Hope it lasts for you..
Looks like a good rig, I have the LA 110 and it's a pos. Wait till your deck mounts start to crack around the welds on these tinny decks. I should of bought something else these things are cheaply made with china parts.
Mine just did that. First the right side gage wheel, then the height adjustment bracket.
Yeah welded mine all up. Decks are thin junk but still going well!
@@jimy4real666 yeah I welded in aftermarket spindle support rings really helped out with the cracking.
The idlers pulley with the perch is pulling out now had to put a bar under the perch to keep it in place.