Приветствую! Шамотный под - это хорошо. Но стальной "потолок" довольно быстро остывает. Тем, кто хочет построить аналогичную печь, стоит подумать о шамотном (керамическом) своде, например, подвесить кирпичи на скобах... В целом, - красивая работа 👍👍👍 Приятного аппетита!
Not sure what Amos your running when u welded that stack....but turn them down...and turn down your CFM s you're pushing too much backing gas as well. If your Amos are lower u don't have to be in a hurry and walking the cup would have been a success
Could you please explain why did you use such thick metal sheets ? 6 mm right ??? Steel cant hold heat anyway it just reflects heat bac into the oven ... Im planning to build same oven but going to use 1 mm stainless steel ... I dont see the point of using such thick metal sheets
The oven is insulated and the outer skin is much thinner. The thick material allows it to hold and radiate heat much more effectively. The oven stays hot enough to cook in for an hour or so after the fire goes out, which demonstrates the advantage of thick steel nicely. It's also less prone to warping than thinner material
@@PetesShredder do you maybe have dimensions of original ooni pro or blueprints ? i think i willl make exact copy , probably going to just put thicker insulation and maybe rotating and thicker stone ... Dont feel confident enough to mess with changing the dimensions especially interior dimensions ... so if you have maybe dimensions od original ooni pro to share ? especially inside dimensions
I've made my own offset smoker, Argentine grill and now I'm going to build a pizza oven and your vid has been very useful for formulating my own plan. Good work Pete Subscribed 😎
I like how you went on about the project but for god's sake please wear gloves when welding. The light damages your skin and the burnt metal... well I guess you know that part.
Приветствую! Шамотный под - это хорошо. Но стальной "потолок" довольно быстро остывает. Тем, кто хочет построить аналогичную печь, стоит подумать о шамотном (керамическом) своде, например, подвесить кирпичи на скобах... В целом, - красивая работа 👍👍👍
Приятного аппетита!
Not sure what Amos your running when u welded that stack....but turn them down...and turn down your CFM s you're pushing too much backing gas as well. If your Amos are lower u don't have to be in a hurry and walking the cup would have been a success
Amps...sorry
Could you please explain why did you use such thick metal sheets ? 6 mm right ??? Steel cant hold heat anyway it just reflects heat bac into the oven ... Im planning to build same oven but going to use 1 mm stainless steel ... I dont see the point of using such thick metal sheets
The oven is insulated and the outer skin is much thinner. The thick material allows it to hold and radiate heat much more effectively. The oven stays hot enough to cook in for an hour or so after the fire goes out, which demonstrates the advantage of thick steel nicely. It's also less prone to warping than thinner material
@@PetesShredder do you maybe have dimensions of original ooni pro or blueprints ? i think i willl make exact copy , probably going to just put thicker insulation and maybe rotating and thicker stone ... Dont feel confident enough to mess with changing the dimensions especially interior dimensions ... so if you have maybe dimensions od original ooni pro to share ? especially inside dimensions
@@leopolanscak4519 no, never used an ooni. This is just based on what felt right. If I were making it again I'd make the roof a little higher
May be the author is the owner of a steel mill.
Inspired by the ooni pro.
if you are stuck with the burner i can help !!!!
im been doing few ovens my self
Gonzalo Fernandez hopefully it should be ok... it's just an area with a fire in it, just like a normal pizza oven
I've made my own offset smoker, Argentine grill and now I'm going to build a pizza oven and your vid has been very useful for formulating my own plan.
Good work Pete
Subscribed 😎
How are you planning to remove the ash,? A hinged bottom would be nice.
I like how you went on about the project but for god's sake please wear gloves when welding. The light damages your skin and the burnt metal... well I guess you know that part.
Excellent work, I congratulate you, could you share the plans and measurements to try to do it, thank you very much
Do you have any tips on cutting the baffle to fit that odd shape?
I think I made it from cardboard, trimmed it til it fit then transfer the shape onto steel
Trata que en la parte donde va la leña dejes una puerta para sacar la debida y para que puedas hecharle leña por la parte de atrás no por el frente
⁸8888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888888
Could you share your oven build plans sir. thank you
Hey Pete. What was the total cost in making this beaut?
Hmm, it's a good question. Maybe 200 quid? maybe less.
Started off so good but ran out of steam when you got the the firebox.
Much talking
Thanks man
Esta súper el inventó I imitación de uuni pero haslo mejor usa mejor tú imaginación
Great job