Creality CR10S PRO 3D printer review -in depth video 4K
Вставка
- Опубліковано 31 гру 2018
- After legendary Cr10S 3D printer from the last year Creality released new successor called Cr10S PRO! In this video review you will found out everything about it.
Video contains, Unboxing, assembly, close up look on internal components, Overview, specs, test prints in PLA, PETG, ABS and TPU with close up shoots, Retraction settings, Sound level noise test with DB meter, print peed test 100mm/s, Heat bed warming up time test, Initial thoughts and final words.
Update! Creality now upgraded the CR10S PRO with the CR10S PRO V2 that now comes with the new firmware and new Auto-level BL-touch sensor.
I highly recommend to get the latest version as auto level works much better.
Get the latest Creality CR10S PRO V2 from:
Banggood - bit.ly/2CUseWE
Amazon - amzn.to/2CSFnzA
Get the Creality CR10S PRO from:
Banggood - bit.ly/2WtsoP7
Aliexpress - bit.ly/3jaycXA
Amazon - amzn.to/2VO2Ytx
Popular Online retailers:
Amazon.com - amzn.to/3k08g0K
Amazon.ca - amzn.to/3c3efiJ
Amazon.de - amzn.to/3rnvj9l
Amazon.co.uk - amzn.to/3blB2qY
Amazon.se - amzn.to/3bhU55l
Aliexpress - bit.ly/2GWF50w
Banggood - bit.ly/2T0R8fG
Ebay - ebay.us/OJuoTs
CR10S PRO S3D printing profile - goo.gl/Cq7FLL
High temp resistant magnetic print surface - bit.ly/3uO1n7T
Cheap filament for your 3D printer:
PLA filament
On Amazon - amzn.to/2K6U99U
On Banggood - bit.ly/2pZSiwK
PETG filament
On Amazon - amzn.to/36RHEsz
on Aliexpress - bit.ly/3h8AYLa
ABS Filament
On Amazon - amzn.to/2K5S4LH
On Banggood - bit.ly/2CurLuc
Gear that I use for my videos:
www.nexi-tech.com/gear-that-i-...
You like what I do? Support me on Patreon
/ nexi_tech
I put a lot of effort and time in my videos and I would appreciate if you click on the ''Like'' and ''subscribe'' button.
Thank you so much for your support.
Best Regards!
Nexi - Наука та технологія
Hi Guys! Here are the links of all models that I printed in this video:
www.thingiverse.com/thing:3102638 - Julia Fractal Twist Vase
www.thingiverse.com/thing:3224078 - Mandelbrot Fractal Twist Vase No.2
www.thingiverse.com/thing:1775702/files - esselated Klein Bottles
www.thingiverse.com/thing:34851 - Christmas Tree
www.thingiverse.com/thing:3031049 - Crystal Cluster
www.thingiverse.com/thing:2014307 - baby groot
www.thingiverse.com/thing:1278865 - XYZ 20mm Calibration Cube
www.thingiverse.com/thing:3202258 - Flexible Octopus - Smoothed version
www.thingiverse.com/thing:629338 - Peon230 - Quadcopter
www.thingiverse.com/thing:308335 - The T-Rex Skull
www.thingiverse.com/thing:214603 - Cell stand
fab365.net/items/112 - Robot R
cults3d.com/en/3d-model/art/the-sorceress - The-sorceress
www.myminifactory.com/object/3d-print-the-elder-lighthouse-71894 - The elder lighthouse
Nexi Tech I was wondering if you could link me your print profiles for the Pro
John Krieger You have them in video description
This is the most useful review i ever found in youtube when it comes to creality products and yes i decided to buy it , but yet i need a little help , when i went to the main website of the brand i found couple new models like cr-20 cr-x etc . What should i do now !!!! I am not intending to change it for couple years and i dont want to regret buying the bigger or the newer version please advise :(
@@Ni8kid Thanks for positive feedback. I'm glad that you liked my videos. Ok i get it. Let me tell you that CR-X are not the same printer like CR10S PRO. They are similar to untrained eye but CR-X has alot of issues and some problems that was reported from users as well some You-tubers. I don't recommend CR-X at all and that's why I did not make any review of it. It's just not good two color 3d printer by design and it need's alot of work, also it has lower print quality comparing to Cr10S PRO which is way better choice. Now C20/Pro came on the market before CR10S PRO and it's on the market for some time now. They are not that popular because of the price point. Cr20 is smaller version of CR10S PRO but not the same.
Cr10S PRO has auto level, filament run out sensor, insulation under heated bed, Touch LCD screen with nicer software, Thick removable print plate, Solid state relay, MW power supply, stronger filament cooling fan, upgraded Capricorn PTFE tube with new hot end and better couplers, Double geared upgraded extruder and more... which CR20/pro don't have.
Cr20 has the same print volume like Ender 3 but it cost twice as much. I can't really recommend it at that price range.
CR10S PRO is the best printer with huge print volume that I tested so far under 1000USD. My advice: Just get one and enjoy in 3D printing.
Promo code GB3DCRP is no longer valid.
Ordered my CR-10S over the summer because of your review and might have to get this one too! ;) Thanks for the great reviews.
You welcomed Tristan! Thank you so much for your comment and for your positive feedback. Wish you all best in 2019!
You really know how to produce a quality and consistent review of the 3D printers. Thank you very much.
What an awesome review! So thorough and concise. I will definitely give you a shout out on my channel when I start doing some 3D printing builds.
Thank you very much for this review. I loved how thorough it was, and the process shots.
Thanks very much for taking the time to do this very thorough review, looking forward to buying this printer !
after many months of research i am at the absolute threshold of tedium and annoyance watching videos on 3d printing.. and let me tell you, this video was a breath of fresh air.
absolutely amazing video.. and i think i've watched every 3d printing video ever made at this point lol so well done and thank you.
Your videos are very professional and easy to follow. They inspire me to purchase a 3D printer! Thank you for the extra effort!
Thank you for this awesome review ! This 3d printer, and your 3d prints are very impressive. I have a CR-10S but this one is clearly another level
Great review of CR-10s Pro. But the robot is our design. So I hope you mention my foldable robot in the movie next time. Thank you~ These days we are suffering credit issues.
Print looks good... are there any complaints? “No, complaints.” I love the review. I want to learn everything about printing from you.
Of all the reviews this is the very best. Well done.
I'm on the look out for a 3D printer and have been watching Creality and Prusa for just over a year. I think you have convinced me what I want in the next month.
Creality have done a stellar job on their production and quality management.
Q. What materials is the CR10S Pro not good with?
Anyway, excellent video. You really put the time in for this one and the results show that.
Bro so good ha! Best review I’ve come across so far. Your other reviews rate just below or at this level.🤜🏼🤛🏼🤓 Inspirational indeed!!!
Looking good , Can`t wait to place my order after the new year mail back log.
I recieved my cr10s pro on Monday. I love it!
settled, been researching for weeks on end 100 different printers at least...this video review youve made here has sealed the deal. going to drop the money now and get it on its way to me! thankyou for your in depth and honest review.
Thank you so much for such a nice comment. I appreciate it very much! P.S. Get the Cr10S Pro V2 with BL-touch autolevel sensor are more consistent and better. You have link in video description. Wish you a great day.
@@NexiTech yea I noticed after the fact that this was the cr10s pro lol, I’ve been looking at the v2 and I was thinking ur vid was the v2 but nonetheless it’s still a great example of quality that can be achieved :) thank you for your hard work !
It's the same machine only the autolevel sensor is upgraded. Glad you like my video and that you found it useful. Wish you all the best! ;)
Best CR10S PRO review I have seen, well done!
Thank you so much!
I totally agree ! :)
Thanks for another great review, this channel is always my go-to for the best printer info and reviews
Enoch Root Thank you so much man! I wish you all the best in new 2019! Glad to have you here.
Finally a solid review of this printer. Been waiting a while. Thanks
You welcomed mate! I'm glad that you liked my video. Thanks for stopping by.
Thanks for the great video. I ordered one 6 weeks ago and it is yet to be delivered. I am not happy but excited and hopeful.
You welcome Tom! 6 weeks? Where did you order it from?
Good to see Creality is making some improvements! Hope they do the same for the rest of the printer line.
This is fantastic, very detailed and tested review. Thank you, and I’m subscribing 🎉
I'm glad it was helpful. Thank you and welecome on board.
A very thorough review. Well done. I enjoyed watching your review.
Joe Valasko Thank you so much Joe! I'm glad that you liked it. Wish you all best in new 2019!
Very good review, one of the best I've seen, think you sold me on one of these printers!
Demetri Kaldelis Thanks man! I'm glad that you liked my video.
Wish you all best in new 2019
New to this technology but a Machinists familiar with cad/cam 3d software I thank you for such a well documented insightful look at a front runner for my 1st future purchase. Keep up the good work. (Caught your fan upgrade video, a definite immediate purchase)
Just got mine, I think it has now replaced the Chiron as my favorite large format printer! Great review, thanks.
Wow, this outbeats the tevo tornado easy, made me change my mind instantly! Great presentation bruh!
Thanks Gerardo! I agree :) Thanks for stopping by.
I rarely have ever liked or commented on a video, but damn! You gained a sub! BEST REVIEWS! So indepth and 25 minutes went without notice.
I like your review, very satisfied..
I have no complains!
thank you for doing this review...time to step up from my Anet 6 :). what an awesome build
Great review. Thanks for your inputs. Now am going to get this printer soon.
Yet another awesome review, like the time lapse.
Peter Waugh Thanks Peter! It's not there yet but I make some progress :) I'm still waiting some parts for Timelapse setup to arrive.
I have No complaints. Very nice Review.
A video as impressive as the printer. Very good work. Congratulations!
Just bought it. Thanks to you ;)
When 3D printers started I didn't think they could become this impressive.
Great video, I'm saving to buy this printer! Hope you do more videos with other suggestions the more you use your printer. Total noob here, so any info is appreciated.
Excellent review, thank you!!
Another AWESOME video Nexi😁👍👍👍
BLACK SHEEP SQUADRON Thank you so much man! Best wishes in new 2019!
Thank you for this review. I will buy this printer. I saw your channel for the first time right now. I give you a sub
You welcome my friend! Glad to have you here :)
Great review we are waiting to see a replacement of the fan! Gj
Excellent review I will be saving for one of these!
Hi, jst wondering if you have any thoughts on the Artillery Side Winder x1
hi, i was so close to buy the CR10S in fact i bought it but.. problems with shipping never got it.. long story ... anyway... thanks for your review... you sold it to me.. so im on my way to get one. cheers !!!!!!!!
The CR10S suits me way better than the pro.
I love the seperation of the controller and printer. Great for enclosures.
My husband just bought me this for my birthday this week!
Awesome review, it might have been nice to see some CR10S vs Pro prints with exactly the same settings?
Nice to see you again 😎
cem inan You too my friend! Wish you all best in new 2019
Great review as always!
MrShott13 Thanks mate! Wish you all best in new 2019
Good review. When I'm in the market for another printer, this is a contender...
Thanks
WOOOOOW i'm so new to 3D printing like 4 weeks into it , i'v created my own channel ..But this is awesome ...
Wow they really didn't skip on anything, they even used Meanwell power supplies in them, neat!
Such a fantastic review, THANK YOU ! :)
And thank you for your awesome comment! :)
Hi. Really impressive video. Thank you.
Another good video. Thanks Nexi!
Artur Fuste You welcome Artur! I wish you all the best in new 2019!
Awesome review!
Thank you!
The best thing about this channel when reviewing is the amount of model this guy prints 10/10
Fantastic review, and great explanation which helps me as someone who is new to 3D printing.A dedicated subscriber and look forward to more In 2019.
Ian Dawkins Thanks mate! I'm glad that you liked my video and found it useful. I wish you all the best in 2019! Cool to have you here
Thank you so much, as a newbie to 3D printing someone like you that can clearly explain technical issues in an understandable way drives me forward. Just upgrading my Ender 3 which I have fad for a few months but totally addicted to 3D printing. Best wishes for 2019 and please keep the vid's coming.
thank u so much for good guide!
Great review. Thank you.
In two week I will have one too. Your videos are very helpful. Thank you!
Love your channel, always great content. After watching this, I was about to order the Pro over the CR10S500, but I saw TinyMachines has the Mamorubot SX4. Wondering if you have plans to review one.
awesome thanks a lot!!! really good tutorial
Thank you for your great video man.
You welcome man! I'm glad that you like it.
Hey! I love your reviews. They are amazing! Since you have reviewed both the CR-10S and the AnyCubic Chiron, which would you recommend?
Nice review and nice prints, this machine looks nice and clean and well built. I’m looking for a machine to replace my Anycubic Kossel Delta with, this just may become my next printer? Sounds like I would definitely want to make sure I get the inductive sensor, as I see the leveling was the only complaint in comment section. Cheers 😁👍
Hi very good review thank you very much,,I just can’t make up my mind CR10S or pro. I was very happy to see 10s printer settings in latest Cura,but not for the pro ? Keep up the fantastic work 👍
I have no complaints
I do not disagree with your review of the printer. I did have some issues: 1> The fans are too loud as you mentioned. I do not feel this is acceptable as quieter fans are not that much more expensive to install from the factory, but to buy them retail and retrofit them after the fact, that costs quite a bit more. It is a worthwhile upgrade though in regards to the end result. Thanks to videos like yours (and your later CR-10S Pro videos) I am in the process of replacing ALL of the fans. So far all I have left to do is replace the 2 fans on the hot end. I replaced the rear exhaust fan with 2 fans wired in series. I also replaced the controller board fan with 2 fans wired in series using a double fan bracket that I designed with inspiration taken from the single fan bracket. The second fan is pointing at the relay. On my printer that I purchased almost 5 months after yours, there was a large aluminum heatsink on the DC Relay. That is a really good upgrade that Creality has done. I also replaced the power supply fan as well, but that one was almost plug and play except having to splice the wires. I turned on my printer for the first time with the only stock fans being in the hot end and it was very quiet. I was upgrading the touchscreen and controller firmwares to a TM3D version. I have 2 more fans on order and look forward to seeing what the machine is like after those two are replaced. I will probably have to go through a PID recalibration to make sure that it is setup properly, but in exchange for the low-noise level, it will be worth it.
Thank you again for your videos as they are part of the inspiration and information needed to take on upgrades like this. I am also in the process of installing a V3 BLTouch and I just read about applying a jumper to a couple of pins on the break out board Z- to make the BLTouch work properly. The other mods I have done right out of the box include the z timing pulley and timing belt mod so now both z axis' stay synchronized as well as the T8 backlash nuts being installed. I also am installing the all metal micro swiss hot end and eventually when the Zesty Nimble arrives, I'll get that installed as well. I do wonder why Creality doesn't have the anti backlash nuts and the timing belt sync done from the factory. Those two things would be less than $10 in parts (for them) but greatly improve the repeatability of the printer design. Even paying retail prices those two upgrades alone were less than $20 and if I had wanted to wait longer to receive them I could have gotten them for less than $12 total.
This printer is very impressive. Creality must be very proud.
Savage Noble I agree. This is the best 3d printer that Creality made so far. They should use different name as it is completely new product.
Yeah like the CR-10X. 😂 don’t flame me!
First of all, thank you for this Amazing review!! Loved it! (I actually watched it twice lol)
I'm really new to this world, but when i saw one working with my eyes last year here in London ,I fall in love .
It's been 1 year since I'm looking on all the best affordable 3d printers , and i will not buy the PRUSA MK3, cos it's absolutely not worth the money for the problems and the quality of the prints.
So, do i go with buying this one??
I think this cr10s pro it's a badass printer 😎😏
Mike Giorgio I searched a lot (as you) for my first 3d printer back in 2013 - my Ultimaker2. And yes, this CR-10S Pro printer looks like an awesome value for money. I’m searious thinking to get one of those.
If you don’t want a so big size machine, depending on your aplication it’s not necessary, you should also take a look at Tevo Flash (with all add-ons: TMC, double Z) that is also a good printer for the money, by far the best printer from Tevo. And it’s not small... bigger than Ender 3 series that I consider a good size machine. But Tevo Flash needs some small adjusts in my opinion to go the level of this one... but it’s cheaper
Cool mate! I'm glad that you liked my video. Yeah me too! I love the idea that you can design and produce any type of plasitic object in your home and with materials like PLA,PETG and naylon you can have very strong plastic part or object. I also like how 3d printing community is growing rapidly. Now we don't need to pay tons of money to get decent 3d printer. Look my Ender 3 review. For less then 200usd you can get very nice medium size machine with impressive print quality for the price point. Now we have Cr10S Pro for big prints and with some awesome improvements over the cr10S from the last year. Love my CR10S PRO and it's my favourite big size 3D printer now. I highly recommend it.
@@NexiTech that's my main problem, because I believe the ender 3 does the same job as the cr10 right? So what one do you raccomed?
But again , i never own one yet so , I'm based on people's review.
For sure, i wont buy a Prusa , maybe I'm wrong, but for me a 1000k machine , that has clip tie to hold main components and that doesn't print as people say . I see cheaper machine printing better and cleaner than that, so it's not worth the money . But again its just my thinking.
I'll go for the cr10s pro but I've just find out about the cr20 lol.
PS : I watched your ender 3 rew before this one weeks ago ☝️🖤
Thank you i am researching the purchase of a printer , your presentation was very good to help me, a friend of mine has a Cr 10s and i can see this later model will give me a starting point to work from. Once again thank you presented very well. Also what camera do you use to do you videos ?
şahane bir inceleme videosu, yorum yazmazsam haksızlık olur, bravo!
Great video
Thanks
Great video, as always! Please tell me which filaments of which manufacturers do you recommend?
Really well done review. Thanks Nexi. Did they updated their 500cm model too?
Darko Sola Thanks man. Not for now. I'm not sure when they will update Cr10S4 and S5 model.
Bravo Nexi, excellent presentation and great advice. I'd like to deepen the note you made on the capacitive probe of the CR-S10 PRO. Because I had a lot of difficulty adjusting for the leveling of the heated bed. Thanks and good 2019!
Can't wait for all of these improvements to come to the Ender 4 lol. An upgrade kit for an Ender 3 would be nice. Great video as always.
Drew Lakebrink Thanks man! I don't think they will add them all because of the low price point. I just got Ender 5 but i did not got chance to open the box yet.
Thanks for the video....it looks crazy printer lol
Hi,
This is the best CR10S Pro review I've ever seen. Thank your for your detailed effort. I purchased a v2 version of this machine after I saw your video. For two weeks I am dealing with it. I strength the Z axis accentric bolts, did the antibacklash nut mod that you did and mostly solved the Z axis falling issue. I also change the bed surface with original Creality Glass bed but I did not liked it because it does not stick enough, and prints pup off during print or warp. So I changed it again with original Creality Cmagnet magnetic bed and I am satisified with it now. Its still sticky as the default bed and also easy to remove the parts after printing.
To conclude I am trying to maximize the quality of my prints with Esun PLA filament, and try different setting but can not improve anymore with Cura so decided to move to Simplify 3D. Can I use your S3D profile with v2? Or do you have any further suggestions ?
Thanks,
Onur.
I have this printer it's very good best printer out of my 6 other printers I bought in the past 3 years.
I agree. Creality did awesome job with CR10S PRO
Thanks for the great video... i just wonder why other 3d printer reviewer can't review like you...
Cleorina Thank you so much. Well other channel's can easily make 5-10 videos in the time that I only make one. That's the difference ;) I put tremendous amount of time and effort in to my videos trying to cover as much as details possible in one video review with highest video quality that I can record. Everything for my awesome subscribers and viewers. There is nothing better when after your hard work nice people like you write positive comments and appreciate your work and effort. That positive energy is what drives me to make more videos and continue my work.
Wish you all best in new 2019!
Nexi
Other channel's (which i don't want to name and have more subs that you) just like to compare this printer like pursa, ultimaker and other Expensive brands... when the print quality not what their expected or their standard keep saying YOU GET WHAT YOU PAY FOR... your review not about that... you will try to fix, do the Calibration till the 3D printer run perfectly... i happy there someone like you who review product and if it's need improvement just buy few upgrade like the TronXY X5SA (which i buy after your review and it work great with extra upgrade that you recommend). Keep up the good work... i enjoy your printer vid review...
Btw will you review the new Ender 5 printer anytime soon?
@@ccleorina I have Ender 5 already but I did not had chance to open the box yet. I start with unboxing and testing as soon as I can.
Great!!!!! i cant wait for the review...
Thanks for the video.
You welcome mate!
fantastic and very good video
well explained 3d printer
wonders how
Creality 3D CR-10-S5 3D printer
it's big print
500x500x500.mm
Great review! I hope to get this printer soon :) However: Please credit the different makers of the printed models that you showcase either in the video description or better yet in the video when you show the respetive models :)
Sintoxic Thanks! But I did left the pin comment with all models that I printed in this video with names and links. Please take look in the comment section.
Best regards and thanks for positive feedback.
Very nice review m8 ! What software you need to slice ?
Excellent review sir, well which Camera DSLR you are using
Great video - finally one that actually does a real review of the printer!
How did you do the timelapse video without the extruder being visible? That was really cool!
Thanks Mike! I'm glad that you liked the video.
It's not that hard. I use simple micro switch which i place on X axis and connected with my Sony A6500 external remote control. On S3D layer change script I wrote few lines in G code and when printer finish one layer he move out to the switch and press it which takes the photo, so you have like one photo at each layer. Then I just combine photos and get that smooth timelaps effect. Negative side is that you need to have perfect print settings otherwise you will get a lot of stringing all over the print and print time is a bit longer then usual. I might made video about it if more people get interest.
Nice, thank you.
wow ur review is ...wow dude all i wanted to know u have tell it O_o damn i'm impressed on a review....now i want one lol gj dude keep great work
I would be happy to have an ABO back.
Fantastic review! Would you recomand CR10S Pro or the Tevo Flash? If you think that the 2 printers are comparable, where do this printer win over Flash and where Flash shines? Thank you and keep the good work with this deep reviews!
Great review well done! can you share the settings for the flex filament (octopus) ? i can't get that good results !
I was cringing at you hacking at the printed models. I was hoping your demo the springform removable bed to show how easy it is to remove. Overall this video makes me wish I waited and saved $ for this vs the Ender 3 Pro 😭. Oh well. It was my very first 3d printer and now I have something to look forward to and save for. Thanks for the awesome video!!
This printer is better than the Ender 3 Pro except for its price. Typically the Creality CR series are better than their cheaper Ender sisters.
Subscribed, getting my first printer in 2/3 week, but I hesitate between cr-10s and cr-10s pro
Thanks.
Hesitate? I take CR10S PRO every time over the CR10S.
Very convincing!
AWESOME review, thank you so much! Those few dislikes much be accidental clicks :-)
You welcome Jans! Yeah :) Thanks for stopping by mate!
orderd one!
The vase design is actually a Klein Bottle. What makes it special is it only has one surface.
Yap, its very cool vase design. I love it.
I also have this printer and loved your review. Would you mind posting a list of the various print settings you had the most success with? I have some TPU I am interested in trying but I completely new to 3d printing and would love a place to begin.
like your videos Nexi very informative and understandable. I was able to find a refurbished CR 10S Pro in my budget $400. It looks brand new. As I see this video you get some remarkable prints. Then I see the follow-up Videos with Upgrades. Am I in trouble with this unit or are all the upgrades required. Can you offer any short list or priority of upgrades to do first. I like the printer and have been using the M3D mini for 2 years which is a much smaller plastic unit with little technical interface. Now I get to really see and touch the guts which I look forward to. But I have to throttle the spending. Thank You for making such great video. Dennis