Thank you for the video, I have a Chevy Silverado 2017 just got it a year ago from the dealership, but the breaks are not working at all pedal sinks in all the way to the floor and it doesn't breaks at all , what do you think is the problem?
@@jerryjimenez8248codes? What the hell are you talking about buddy he might have a leak or maybe air in his system. You sound just like the dealership
Have a 2015 jeep Cherokee with low miles and the brake booster went out. Mechanic replaced it, went out again in 6 weeks. Replaced it again then said I needed to replace master cylinder…3 months later went out again and it’s currently at same shop for a week now. Jeep told him it’s a bad check valve but he thinks it’s due to recall W84 which is a transmission software flash…what is going on??
My question here hope u can help me my car brakes locks up so when I disconnect the check valve from the booster u hear air released and brakes gets released immediately I replaced the valve with a dealer one and still the same also replaced master cylinder pads rotors and calipers any idea will help me a lot and thank you
nathan sonnen ,usually push rod comes pre adjusted (where conect with master cylinder) for certain vehicles and on some vehicles like my 06 nissan frontier 4.0 V6 it didn’t work,I had to go with OEM parts and they’re very expensive. I found out hard way,there’s adjustable and non adjustable power brake booster. I’m not mechanic and I came to dead end cause push rod was pushing inside a master cylinder and kept brakes engaged all the time wich caused brakes to lock.
Hey muhamed I have the same problem after installing the booster on my 2000 Malibu. How would I solve this problem becuz I don’t think my pushrod is adjustable and my brakes locked up
@@humbertohernandez2739 ,The only option I had was to go and get OEM parts from Nissan and install it and that solved the problem for me.Unfortunately,it is more expensive but on the bright side I don’t have a problem anymore.
2003 Ford Taurus is not that easy because part of the frame is blocking it from coming out but thank you, anyways. It looks like he has new master cylinder but he didn't bench bleed it or bleed it in anyway, isn't it necessary to bleed it or can you just bleed it though the brakes?
We have a separate video detailing how to install a new master cylinder, including how to bench bleed it. We also have a video on how to bleed your brakes. Both can be found below: ☘️ How to Replace a Master Cylinder: ua-cam.com/video/StkzzZWr3Ac/v-deo.html ☘️ How to Bleed Brakes: ua-cam.com/video/Y7dIUdIL6RE/v-deo.html
My name is Alexander Delgado. I am studying the automotive industry. I am currently living in California, and I am currently a student at Santa Ana College.
Very verbally informative but visually as a video you don't show what your describing at all making this a horrible tutorial video. Most people as they explain the task sit there and show you how it's done
Supplies Needed for This Job:
1. Safety Glasses: urlzs.com/hbwc
2. Gloves: bit.ly/2GvfwAm
3. Chocks: bit.ly/2ZvIW98
4. Brake Line Flare Wrenches: bit.ly/2Dyk7jt
5. Crescent Wrenches: bit.ly/2DI3x0P
6. Socket Set: bit.ly/2UUqY1p
7. Brake Booster: bit.ly/2UDDn4G
8. Brake Fluid: bit.ly/2VpQfzT
9. Siphon Tool: bit.ly/2IFNXXk
10. Drain Pan: bit.ly/2GEzWqK
11. Shop Towels: bit.ly/2viLw4m
12. Brake Cleaner: bit.ly/2UxiRmp
I’ll pi
How are you to know the booster pushrod to master clearance is within spec?
This is a great example. I feel confident doing this now. The last "tutorial I watched made it look impossible.
O'Reilly's thank you,
Chris... you the man!
Thank you. The brake booster on my Honda Accord completely gave out yesterday
Thank you for the video, I have a Chevy Silverado 2017 just got it a year ago from the dealership, but the breaks are not working at all pedal sinks in all the way to the floor and it doesn't breaks at all , what do you think is the problem?
Check your lines or use an OBD scanner to read the car and figure out what the codes are
Blown line
I'm having that same problem with my 04 Dodge Ram. Did you get it fixed?
@@jerryjimenez8248codes? What the hell are you talking about buddy he might have a leak or maybe air in his system. You sound just like the dealership
@@joelh3030 vehicles with ABS need scanned and bled with proper scanner……………
Great tutorial. Most make it look very hard to do. Im sure I can do it on my own after viewing this video. Great job thanks
Have a 2015 jeep Cherokee with low miles and the brake booster went out. Mechanic replaced it, went out again in 6 weeks. Replaced it again then said I needed to replace master cylinder…3 months later went out again and it’s currently at same shop for a week now. Jeep told him it’s a bad check valve but he thinks it’s due to recall W84 which is a transmission software flash…what is going on??
You never adjusted the brake booster pin. This can lead to the breaks locking up, or lack of breaks.
What pin are u speaking of?
The pin rod that goes into the master cylinder.@@rynow1992
What about adjusting the pin? Does Oreilly have a loaner pin adjustment tool?
Trying changing a booster on a 2003 Saab ! The main bolts that hold up the booster is behind the booster and not by the brake pedal.
Did you get a brake malfunction on sid when you brake booster is bad ...I have this message and can't figure it out
that top right bolt of the brake booster is the devil!!
Snap On..........any questions~
@@ironjohn5914
Yeah. How does Snap On change the location of the bolt? lol.
@@OTEP1234567891011 there's a special snap on tool just for that bolt.... 🔩 ⚡️ 🌩 🙏 🤲 🕍
Once I installed the booster on my 2002 escalade how do i got the brakes to start pumping?
do you need a Power Brake Booster Pushrod Pin Adjustment Tool?
This is the Best video straight to it thank you
My question here hope u can help me my car brakes locks up so when I disconnect the check valve from the booster u hear air released and brakes gets released immediately I replaced the valve with a dealer one and still the same also replaced master cylinder pads rotors and calipers any idea will help me a lot and thank you
sounds like booster failed, check if the master cylinder is leaking fluid into the booster when replacing booster
if you replaced the booster, keep in mind you muat adjust pushrod for the booster on the master cylinder side or it could lock up brakes
I already changed a new booster. But my brake fluid is still low. Can you tell me why.
Check your fluid levels and top them off as needed.
Don’t forget to adjust push rod on brake booster or you may end up with soft pedal or locked up brakes.
What do you mean
nathan sonnen ,usually push rod comes pre adjusted (where conect with master cylinder) for certain vehicles and on some vehicles like my 06 nissan frontier 4.0 V6 it didn’t work,I had to go with OEM parts and they’re very expensive. I found out hard way,there’s adjustable and non adjustable power brake booster. I’m not mechanic and I came to dead end cause push rod was pushing inside a master cylinder and kept brakes engaged all the time wich caused brakes to lock.
Hey muhamed I have the same problem after installing the booster on my 2000 Malibu. How would I solve this problem becuz I don’t think my pushrod is adjustable and my brakes locked up
@@humbertohernandez2739 ,The only option I had was to go and get OEM parts from Nissan and install it and that solved the problem for me.Unfortunately,it is more expensive but on the bright side I don’t have a problem anymore.
@@muhamedpuric277 well imma have to look into that then, appreciate the heads up
what if the pedal never really stiffens up?
Good video. Too bad it doesn’t tell you to check you booster rod measurement. You might wanna check that too
Nice quick presentation.
Thank you i do it with my dodge nitro 2011 and now is excelent❤
Didn't say anything about adjusting the booster pin going into the master cylinder
Great presentation mate thanks
Perfect video for this job. There was a 30 minute video on just the master cylinder. 5 minutes is plenty.
Good info and knowledgeable tech. But slow down a bit for us seniors to comprehend.
Helpful tip: you can slow down UA-cam videos in the settings.
That might help you.
youtube also has a feature on the videos where you can pause and rewind so you can go back and listen again
Where do I hook the oval shaped wire by my master cylinder
Nice sharing... Thank you from Malaysia
2003 Ford Taurus is not that easy because part of the frame is blocking it from coming out but thank you, anyways. It looks like he has new master cylinder but he didn't bench bleed it or bleed it in anyway, isn't it necessary to bleed it or can you just bleed it though the brakes?
We have a separate video detailing how to install a new master cylinder, including how to bench bleed it. We also have a video on how to bleed your brakes. Both can be found below:
☘️ How to Replace a Master Cylinder: ua-cam.com/video/StkzzZWr3Ac/v-deo.html
☘️ How to Bleed Brakes: ua-cam.com/video/Y7dIUdIL6RE/v-deo.html
There is no place that I can find where too plug a wire in around my booster pump and master cylinder on my 2003 chevy Avalanche
My name is Alexander Delgado. I am studying the automotive industry. I am currently living in California, and I am currently a student at Santa Ana College.
Thank you, I need to replace the brake booster in my shitbox. It’s so shitty. Not worth it to send to a mechanic 🤣😂
Como poner una banda a una fristar 2004
Play loud Country music 🎶 it helps~
Hello Sir my car have a many problems will fix that
Good video! Can you use a regular wrench with a rag on a line fitting if you don't have a line wrench?
Thanks for the help
I hope this helps for my 2000 Chrysler Concorde
Thank you
Great video! Thank you.
Good forgot to say made should the booster gasket is in place
Porque se escucha que raspan despues de ser instalados
thanks brother
Very verbally informative but visually as a video you don't show what your describing at all making this a horrible tutorial video. Most people as they explain the task sit there and show you how it's done
Just did this exact thing today, he actually explained it very well.
Lmao Chris said meet him tf outside 👊🏾
I have to tippy toe my brakes just to start braking, I almost crashed because I got too used to the gas pedal
🤔😄
awesome
cant get my ebay booster in :(
about to call a mobile
I did it all but now I have no brakes at all ? Car does not have any pressure
That's my problem right now. Did you get it fixed?
Yea make sure the middle skinny rod goes through the hole in the center
Thanks
Turn off the car Swallowed the Key now add....
Rio it across a cussing ways to get
" No One likes you booster!"
Sinbad
👌🏾
You forgot to bleedthe master cylinder
This is so generic...doesnt help me at all
Like
WHAT ABOUT ADJUSTING PUSH ROD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Tutorial my ass
Nn
THEY HURTED MY FEELING TOGTHLER IM BELINAY TUNCELOWEQOWEQ
Too much talk
Pollo
If I wanted to hear someone talk me through it, I would have read the repair manual out loud..
Then why didn’t you do that?
Great video, thanks!