Another important step with respirators, is with no cartridge attached, after you don it (put it on), place your hand over the input valves, and breath in. If the mask is worn properly, with no gaps, the mask should suck to your face. If it doesn't, then you have a gap somewhere and either need a different sized mask, or need to adjust the straps more. A little firefighter tip. :) We do that everytime we don our SCBA's to ensure a tight seal, or it could be life or death.
We do the same thing in industrial environments, always do seal checks. You can do it with the filters installed, but you have to cover the intake. Also check by covering the exhalation valve and breathing out gently, the respirator should balloon slightly and you shouldn't feel air escaping.
@@lakerzz123 yeah part of the OSHA requirement to ensure proper seal before donning your respiratory. No smoking at least 30 mins before. Else it'll affect the results. I'm a Fit tester. 😉
Extra tip: Respirators generally require you to be fairly clean shaven to seal. In order to test the seal, wear your mask for a few minutes to allow it to set to the shape of your face, take off both filters, and plug the holes with your hands. Try to breath in and see if you feel any air flow around the edges of your mask, there should be a firm negative pressure created between the mask and your face.
+Deadbeatloser22 +Jonas Habben Well, I'm a military firefighter in the austrian army and I have a beard. I have never had a problem with getting a tight seal on either the NBC-mask nor the SCBA-masks with various lengths of beard (3 mm to 3 cm). It may be true for some people (reason may be an odd shaped face or "harder" beard hair, idk...) but it's definetly not a fixed rule that a beard ruins your seal. I'd guess this was a problem for old gas masks, but not a problem for newer models... Does someone have some statistics about this topic?
This is a required step when putting on a gas mask in the military. Plug the filter with your hands and breath in, which not only checks for leaks, but will pull the mask closer to seal onto the face. If it doesn't, then the mask is faulty, and knowing that immediately could save your life.
Required step when you initially adjust the mask to fit your face (and when you do battle preparedness drills, if you need to adjust your mask when you need it something has gone wrong). When in an actual NBCR attack you are supposed to bread out heavily after you have put the mask on to remove any possible contaminants that might have floated into the area between your face and the mask.
It's also super important to regularly clean the inside of the respirator with an alcohol wipe, especially if it's used for long periods of time. As someone who does a lot of grinding I can tell you that it can get real sweaty in there and is a great place for bacteria and mold to grow
Dang, all this time I've been putting my dust mask on by stepping into it feet first and pulling it up my body. Thanks for the tip on a better way to put them on, guys!
I had the problem of poor seal around my beard and I was working in an environment where there were both solvents and some fairly nasty particulates. I got a respirator which had an internal mask with another full face mask that covered over the forehead as well. You might think this was uncomfortable but it also came with a belt mounted blower fan powered by a rechargeable battery. This had two combination chemical and particulate filters on the fan intake. It supplied cool filtered air to the mask. This meant the mask was at positive pressure. Air was vented out of a release valve in the mask but it also meant that air coming out where the seal was not good also kept particulates and fumes out. Smart electronics meant that as the filters became loaded with dust more power was delivered to the motor to keep the air flow constant. I used to way the filters before and after changing them. Over a 3 month period they removed on average 64 grams of dust that would have been destined for my lungs.
This needs some serious factual correction. In the US: 1) Dust masks are known as “filtering facepieces” when not required to be used in the workplace by your employer (who has the responsibility to test the workplace to determine if respiratory protection is required). They should be rated by NIOSH as N-95, N-99, or N-100 to determine the size of particulates they are rated to filter. Employers must provide a copy of Appendix D because breathing through a filtering facepiece can increase the work of breathing and decrease the amount of air drawn in with each breath. 2) When dust masks are required for use in the workplace, they are considered to be “respirators” and users must be fit-tested and undergo a medical examination to determine if they are able to safely use a respirator. 3) The distinction between organic vapor filtration and particulate filtration is in a rating that is assigned to a full-face, half-face, or filtering facepiece mask - NOT the type of mask it is. Masks that use canisters will have a color coding system for the various compounds they protect against. Filtering facepieces (N-95, R-95, P-95, etc.) have the letter designation that indicates the compounds they protect against (N=NUISANCE dust; R=oil RESISTANT; P=oil PROOF). Source: I am an occupational safety investigator in state government responsible for enforcement of the US Department of Labor’s OSHA standards. See this link for more information: www.osha.gov/dts/shib/respiratory_protection.pdf
This comment needs to go to the top. I was just about to state, less than 2 minutes into the video and they are miss-informing people. Noting the fact that the "dust mask" he is holding could in fact be labeled as a "Disposable Particulate Respirator" which will give people the wrong idea on what it does.
I don't doubt that the authors intended to provide some basic level of information to the DIY crowd. My concern is with employers that decide to apply that information in the workplace and that potentially provide their employees with ineffective protection. That being said, it's always better to have the proper type of PPE for the hazards that are reasonably anticipated, in the workplace or for the weekend warriors. Frank Ippolito if you think it would be of any use, I'm happy to help you and your team with any occupational safety related topics you wish to cover. Cheers!
CharredChar Krishna Jagannathan Our aim was not to mis-inform. We aren't OSHA. it was basically my response to seeing people (hobbyists) spray painting with a dust mask, and show that there are other easily-found safety items at the hardwear store. These tips are geared towards makers and hobbyists, and given in good faith that people will do their own research to augment information. That being said, i'd love to be educated further.
I didn't think you posted this with the goal to miss-inform, I should have stated a thank you in my last post for helping bring awareness of the matter to people. I myself didn't know the difference either when I first started out doing things oh so long ago until I saw a similar post of "Dust masks do not protect you while painting!" I just want people to realize do not always go by just the name of a product, actually read in detail what one type of PPE over another will protect you against.
Respirator is just a face decoration if not used right. Mind the facial hair that may interfere with the seal on the edges of a the mask. That is for all masks, paper to full face masks. I work in a refinery and everyone is required to be clean shaven in case you need to use one in an emergency. If you are caught with to ruff a stubble you will be handed a disposable razor or sent home with a warning. Also, some cartridges have seal on them you have to break to keep the cartridge fresh in storage, so keep that in mind. Do breathing check every time you put the mask on by covering the valves and inhaling. Mask should suck to your face when covered and exhaust check open and let out air on exhale. Its a quick and easy check that only takes a second (one breath), so no excuses.
I also find that even though the respirator appears more bulky, it is a lot easier and more comfortable to breathe through a respirator than a dust mask -- which is definitely nice for a long job.
For glasses wearers, there are 3M respirator versions that vent down, instead of out. I've found this to fog my glasses less, be it eyeglasses or safety glasses.
Technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
Rabid Rabbi you piqued my curiosity, haha so i had to go back to 3:07 to see "what in the hell's he talking about?" Lol. I had totally missed it the first time. Then even once i knew what to look for, i still had to watch it twice to catch it! But youre right. the way he handled that hat was quite smooth/fluid to watch. Those are some good observation skills you got there! I bet nothing gets by you unnoticed. ✌😎
Is that a N95 dust mask? It looks like one in the video. If in fact it is, that is also classified as a respirator and has different guidelines for use from a classified Dust mask.
I can’t believe that this is the only Coronavirus comment! I know there should be more likes on this comment. There’s at least a couple hundred of us that watched this video for sure.
My tip: use a push-stick to feed stuff into a saw. Like how important is it to use your bare hand like a boss vs. finishing your workday with all your digits?
He missed a part about respirators. Some come with cartridges that only filter out air born particles while others filter out the fumes as well. Don't assume you are safe just because you're wearing a respirator.
I've always use my respirator for cleaning out our dust collector and any high particle removal. I've also noticed it also grab those fine dust particles that most cheaper dust mask won't grab
I had my gc buy one for me to pop a hole in the concrete foundation wall with a Roto hammer in a crawl today. Didn’t want to do the concrete in that closed space without it even a dust mask I trust a respirator more
Aren't all filters different? For respirators you can get particulate filters and solvent filters. They've also got their ratings for how effective they are at filtering.
That's what I was thinking. It definitely should have been brought up. So people don't think just because you have a respirator it will keep you safe, if you have the wrong filters.
The 3M half-face respirator is so inexpensive and replacement filters reasonably priced, that there shouldn't be a question on what to purchase. Furthermore, the re-usable respirators are designed to be washed for a sanitary experience. I've used the N95-class filters for plenty of wood and resin composite dust generating activities over the past several years, and they work great.
@@zoeb7654 Better yet, no condom, My boy!!! You only need protection for your respiratory system when [[[[[[ banging a goat ]]]]]]]... Trust me, I've know guys who've used this technique flawlessly for decades - Goat is a great piece of ass, but stinks like shit.
What you are protected against depends on what type of cartridge you buy. There are a whole lot of different types of them. It starts with identifying what you are protecting yourself from.
awhhh nawhhh. To be fair its not as bad as the time they demonstrated how to put paper on a table so you don't get it messy. I think they took that video down as I can't find it haha
So simple yet so relevant to my personal life. I was just thinking about these after painting my car with rattle cans. Gotta pickup a good respirator after watching this video
If you use it or not, make sure you check the seals on your respirators every three or four months and keep at least two changes of filters in stock at any time. Certain kinds clog very quickly.
What about preventing secondhand smoke from ciggarettes? I've tried an N95 mask and the respirator (along with the cartridge attached and it was not expired) exactly like the 2 you showed in this video and both of them did a horrible job with protection I've read some of the comments you guys posted and some of you said if you have a beard, you should stubble it or shave it off. I might stubble mine and see what difference it makes with protecting me from smoke
If your respirator is letting in smoke I would guess it isn't sealing, if you have a beard then that's almost certainly the issue, a smooth gasket cannot possibly seal against a coarsly fibrous surface. Smooth gaskets seal against smooth surfaces, like bare skin.
Hey tested, you should do a video about fiberglass basics (either in shop tips or as a separate category). I've looked online multiple times to find a good tutorial but no one ever covers all the unexpectancies like fiberglass getting stuck to your gloves because of the resin on them or the resin drying too quickly, or the fiberglass not staying in place (all these are things I've experienced) , etc. From what I've found relating to fiberglass tutorials is that most of them all rely on some sort of basic knowledge about fiberglassing which I have been unable to find. If you guys could do a video hopefully solving all the problems I've had that would be great.
You also want to use the respirator if you are going to be heating galvanised metal (for example welding to galvanized steel) the galvanization gets in the the air and it might give you metal fume fever
There are some experienced people in the comments, so I have a question: I do trust Frank, industry professional and all that, but can anyone confirm what he's saying, That you need an IN-Organic vapour filter for spray paints and solvents. I'm ordering a 3M respirator and everything in their documentation says you need an ORGANIC vapour filter. It specifically says for spray painting, solvents, glues, epoxy & fiberglass resin to use an Organic filter. It only recommends and inorganic filter for working with Sulfur Dioxide :/ So, was it a slip of the tongue or does Frank have some insight I can't find in the documentation?
I was an auto painter for many years, so maybe I can help. Here's a simple test; If you are using a respirator, and you can still smell the chemicals you are working with, It's not working. You should not be able to smell anything, at all. If you are spraying a substance that has a catalyst, such as epoxy or automotive polyurethane, you should go to a "supplied air" type of respirator. This type actually uses a line from a compressor to supply fresh air to the mask, hence the name, "supplied air respirator". Hope this helps.
Here's a link if you want to know more about the use, maintenance, and ratings of respirators. You could also search OSHA respirators. www.osha.gov/dte/library/respirators/faq.pdf
really good info to know. my girlfriend runs a bath product business and all the dust has been concerning me, wanna get some better respirators to protect us from all the particles flying around and also from the SLSA dust, that stuff burns :( definitely don't want us to mess up our lungs
I resisted buying a respirator for a long time because I thought the resistance on the inhale would agitate my asthma, I couldn't have been more wrong, I breath better with it on than off even outside the shop because of the complete lack of dust or allergens. I'm surprised you didn't mention the cost savings of replaceable prefilters especially after knocking one off lol
Pro tip from a chemically sensitive person that's gotten alot of use out of these things: Buy a true vacuum sealed coffee container like the one at (www.amazon.com/gp/product/B01NACX4YQ/ref=oh_aui_search_detailpage?ie=UTF8&psc=1) and whenever you're done, pop the cartridge off and put it inside. Seal it. It WILL store for longer, I promise you that. There's no air coming through it, no depletion of filter. And when you put the catridges back on, there are little notches on the cartridge that line up with that 3m mask shown in the video. They both attach clockwise. Hope this helps someone! I buy the 3m P100 pink cartridges, they are about $20 a pop, nice to save them as long as you can.
respirators come in three flavors: half face (seen in video), full face (includes built in goggles), and forced air. Forced air has a battery powered fan which helps pump air through the filter. This is great for ppl with weak lungs, or if you need to be in it continuously for several hours.
I've been wondering this for a while, because I though one was just a cheaper version of the other, thank you so much. At what point should one start using a respirator rather than a dust mask? Thank you!
They already mention it in the video but dust masks are for keeping out dust or particles, and respirators are for solvents. If you're just sanding things, a dust mask is probably fine. If you're painting or using things that give off harmful fumes, you want a respirator. Even if you're just using spray cans outside! Safety first!
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal.
I've got a safety question for you guys of Tested: what do you do about eye protection when you wear prescription glasses? And I can't deal with the double glasses thing, haha. I'm looking for some type of safety-prescription glasses fusion, any recommendations? :)
hi frank i don't have a shop per say but I do some work with dermel tool. I have been told that I should get a face shield cause I work with metal, would the price of one be worth it even if I don't do it that often
Any kind of abrasive wheel (on a dremel, grinder, etc) has the potential to break apart and shoot out chunks at high speed. When using these it's a good idea to wear a full face shield, and minimally you'd want to wear safety glasses.
slomatt I've had that happen to me, especially when using emery cutoff wheels. Also, the sparks you see when grinding or cutting metal are tiny, sharp bits of hot metal. If these get in your eyes, the can be very painful. In addition, dry grinding produces clouds of fine dust, containing particles from the object being ground as well as silicate particles from the burs. When cutting or carving wood, you get fine sawdust. None of these things belong in your lungs, so you should wear a face mask as well.
What kind of cartridge should you use for acids in electroplating processes? I recently quit because they weren’t following guidelines and didn’t have a fume scrubber in the bay as nickel chloride is quite harmful in the long term. Also note there was sulphuric acid fumes, hydrochloric acid fumes and copper sulfate fumes.
I've used a 3M mask (like Frank's) with 6059 gas filters a lot, for working with acrylic glues and other nasty stuff. Problem is, my nose is kinda big, and although I use the large size, the mask won't seal completely near my eyes... and it's very exhausting and a bit painful to have the mask slighty press down on your nose if you wear the mask for a couple hours... Also a question... you talk about shelf-life on the filters... I suppose that is the use-before date? I'd like to know for how long you actually can use a set of filters with daily use? ( i noticed he said look in the manual...but i can't seem to find it in there )
I looked abit at 3Ms documentation and when it comes to gas-filters it seems you should replace them after 6 months or when you can taste/smell the gas. Whichever comes first. More info here: multimedia.3m.com/mws/media/447121O/filter-change-out-brochure.pdf
I like doing spray painting, I do it outside, I use a Dust mask+shirt on top to seal it better, can I still doing that or I need to change to a Respirator?
devilbiss air hood supply fed respirator is my go to for painting provides cool fresh air and no issue with general facial hair not cheap but to set up. also cleanspace 2 respirator battery air fed perfect for quick work and no air line or expensive filters for fresh air it will also supplie cool fresh air with no obstructions infront of your view like most (respirators)have.
I dearly love my full-face respirator. They're a bit pricey, but the fact that it keeps solvent vapour out of my eyes is worth it. It's the same as the paper mask vs half-mask respirator - safety glasses might keep some of the particles out, but the solvent just wafts right around. As far as brands, just go buy a 3M one. You'd be hard pressed to find a company less likely to go out of business.
Another important step with respirators, is with no cartridge attached, after you don it (put it on), place your hand over the input valves, and breath in. If the mask is worn properly, with no gaps, the mask should suck to your face. If it doesn't, then you have a gap somewhere and either need a different sized mask, or need to adjust the straps more. A little firefighter tip. :) We do that everytime we don our SCBA's to ensure a tight seal, or it could be life or death.
We do the same thing in industrial environments, always do seal checks. You can do it with the filters installed, but you have to cover the intake. Also check by covering the exhalation valve and breathing out gently, the respirator should balloon slightly and you shouldn't feel air escaping.
Also, at my work when I get fit tested, they make me shave, ugh. (just my face, lol)
@@lakerzz123 yeah part of the OSHA requirement to ensure proper seal before donning your respiratory. No smoking at least 30 mins before. Else it'll affect the results. I'm a Fit tester. 😉
@@nashaa3769 Interesting, I didn't know about the smoking rule, thanks.
Extra tip: Respirators generally require you to be fairly clean shaven to seal. In order to test the seal, wear your mask for a few minutes to allow it to set to the shape of your face, take off both filters, and plug the holes with your hands. Try to breath in and see if you feel any air flow around the edges of your mask, there should be a firm negative pressure created between the mask and your face.
And that's why you're not allowed to grow a beard in the military.
+Deadbeatloser22 or if you're a fire fighter
+Deadbeatloser22 +Jonas Habben
Well, I'm a military firefighter in the austrian army and I have a beard. I have never had a problem with getting a tight seal on either the NBC-mask nor the SCBA-masks with various lengths of beard (3 mm to 3 cm).
It may be true for some people (reason may be an odd shaped face or "harder" beard hair, idk...) but it's definetly not a fixed rule that a beard ruins your seal.
I'd guess this was a problem for old gas masks, but not a problem for newer models...
Does someone have some statistics about this topic?
This is a required step when putting on a gas mask in the military. Plug the filter with your hands and breath in, which not only checks for leaks, but will pull the mask closer to seal onto the face. If it doesn't, then the mask is faulty, and knowing that immediately could save your life.
Required step when you initially adjust the mask to fit your face (and when you do battle preparedness drills, if you need to adjust your mask when you need it something has gone wrong). When in an actual NBCR attack you are supposed to bread out heavily after you have put the mask on to remove any possible contaminants that might have floated into the area between your face and the mask.
No one cared who I was until I put on the respirator
Lol
Lol
Nani?
Jason song revrince
Lol that meme
It's also super important to regularly clean the inside of the respirator with an alcohol wipe, especially if it's used for long periods of time. As someone who does a lot of grinding I can tell you that it can get real sweaty in there and is a great place for bacteria and mold to grow
Is it isopropyl alcohol?
With 70% concentration?
Wouldn't alcohol deform the filters?
Use alcohol free wipes. 3m sell them in a box.
Dang, all this time I've been putting my dust mask on by stepping into it feet first and pulling it up my body. Thanks for the tip on a better way to put them on, guys!
I think bloggers should test bcmask masks. I think the masks of this brand are very cost-effective!
@KarlBunker please tell me you are joking.
@@robinhannon3488 Please tell me _you_ are.
This shit is funny as fuck! Lmao u win the internet Karl
I had the problem of poor seal around my beard and I was working in an environment where there were both solvents and some fairly nasty particulates. I got a respirator which had an internal mask with another full face mask that covered over the forehead as well. You might think this was uncomfortable but it also came with a belt mounted blower fan powered by a rechargeable battery. This had two combination chemical and particulate filters on the fan intake. It supplied cool filtered air to the mask. This meant the mask was at positive pressure. Air was vented out of a release valve in the mask but it also meant that air coming out where the seal was not good also kept particulates and fumes out. Smart electronics meant that as the filters became loaded with dust more power was delivered to the motor to keep the air flow constant. I used to way the filters before and after changing them. Over a 3 month period they removed on average 64 grams of dust that would have been destined for my lungs.
wait... are you saying that spraying silver paint in mouth is harmful?
Idupppz
IM HEADING TO VALHALLA!!! REMEMBER ME!!!!
Witness me! ;-)
This made me laugh probably harder than it should of. XD
Yeah lol unless your in a movie mad max ...then it fine
This needs some serious factual correction. In the US:
1) Dust masks are known as “filtering facepieces” when not required to be used in the workplace by your employer (who has the responsibility to test the workplace to determine if respiratory protection is required). They should be rated by NIOSH as N-95, N-99, or N-100 to determine the size of particulates they are rated to filter. Employers must provide a copy of Appendix D because breathing through a filtering facepiece can increase the work of breathing and decrease the amount of air drawn in with each breath.
2) When dust masks are required for use in the workplace, they are considered to be “respirators” and users must be fit-tested and undergo a medical examination to determine if they are able to safely use a respirator.
3) The distinction between organic vapor filtration and particulate filtration is in a rating that is assigned to a full-face, half-face, or filtering facepiece mask - NOT the type of mask it is. Masks that use canisters will have a color coding system for the various compounds they protect against. Filtering facepieces (N-95, R-95, P-95, etc.) have the letter designation that indicates the compounds they protect against (N=NUISANCE dust; R=oil RESISTANT; P=oil PROOF).
Source: I am an occupational safety investigator in state government responsible for enforcement of the US Department of Labor’s OSHA standards. See this link for more information: www.osha.gov/dts/shib/respiratory_protection.pdf
thanks for that info! glad im just a dood in a glorified garage-shop.
This comment needs to go to the top.
I was just about to state, less than 2 minutes into the video and they are miss-informing people. Noting the fact that the "dust mask" he is holding could in fact be labeled as a "Disposable Particulate Respirator" which will give people the wrong idea on what it does.
I don't doubt that the authors intended to provide some basic level of information to the DIY crowd. My concern is with employers that decide to apply that information in the workplace and that potentially provide their employees with ineffective protection.
That being said, it's always better to have the proper type of PPE for the hazards that are reasonably anticipated, in the workplace or for the weekend warriors. Frank Ippolito if you think it would be of any use, I'm happy to help you and your team with any occupational safety related topics you wish to cover.
Cheers!
CharredChar Krishna Jagannathan
Our aim was not to mis-inform. We aren't OSHA. it was basically my response to seeing people (hobbyists) spray painting with a dust mask, and show that there are other easily-found safety items at the hardwear store. These tips are geared towards makers and hobbyists, and given in good faith that people will do their own research to augment information.
That being said, i'd love to be educated further.
I didn't think you posted this with the goal to miss-inform, I should have stated a thank you in my last post for helping bring awareness of the matter to people. I myself didn't know the difference either when I first started out doing things oh so long ago until I saw a similar post of "Dust masks do not protect you while painting!" I just want people to realize do not always go by just the name of a product, actually read in detail what one type of PPE over another will protect you against.
Respirator is just a face decoration if not used right. Mind the facial hair that may interfere with the seal on the edges of a the mask. That is for all masks, paper to full face masks. I work in a refinery and everyone is required to be clean shaven in case you need to use one in an emergency. If you are caught with to ruff a stubble you will be handed a disposable razor or sent home with a warning. Also, some cartridges have seal on them you have to break to keep the cartridge fresh in storage, so keep that in mind. Do breathing check every time you put the mask on by covering the valves and inhaling. Mask should suck to your face when covered and exhaust check open and let out air on exhale. Its a quick and easy check that only takes a second (one breath), so no excuses.
My good buddy Immortan Joe taught me all about respirators.
😂😂
+Аркадий Чукреев Reported
Just like this video... mediocre!
So shiny and chrome
I also find that even though the respirator appears more bulky, it is a lot easier and more comfortable to breathe through a respirator than a dust mask -- which is definitely nice for a long job.
For glasses wearers, there are 3M respirator versions that vent down, instead of out. I've found this to fog my glasses less, be it eyeglasses or safety glasses.
Or just wear contacts lol.
And what about the full face gas masks? Are those only for when you're trying to find your mummy?
They're used mainly when you're T side. But you can also use them if you put a tear gas, mustard gas, or smoke gas grenade on you class as well.
Cool Doctor Who reference!
your giving me flashbacks!
Lol love the reference!
that episode gave me fucking nightmares... actual fucking nightmares
Technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
3:07 I can't stop watching him casually flipping the hat around with his fingers. It's just so quick and fluid. Oddly mesmerizing.
Rabid Rabbi you piqued my curiosity, haha so i had to go back to 3:07 to see "what in the hell's he talking about?" Lol. I had totally missed it the first time. Then even once i knew what to look for, i still had to watch it twice to catch it! But youre right. the way he handled that hat was quite smooth/fluid to watch. Those are some good observation skills you got there! I bet nothing gets by you unnoticed. ✌😎
Is that a N95 dust mask? It looks like one in the video. If in fact it is, that is also classified as a respirator and has different guidelines for use from a classified Dust mask.
You merely adopted the shop tips...
I was born by them! Molded by them
Or as you,re mother said -Safety first Deer😉
+lasarith2 dear*
You sand like a younger man, nothing held back. Admirable but mistaken
bigguy4u
his profile picture is a deer
CORONA VIRUS GANG ... Where you at ??? 😂
MysticMarble 😂😂😂
I can’t believe that this is the only Coronavirus comment! I know there should be more likes on this comment. There’s at least a couple hundred of us that watched this video for sure.
ACHUUUU I SNEEZE ON YUUUU
@@flar7684 CCP- Citizens! grab Flar can't let sick ppl infect healthly ppl.
#CORONA-VIRUS-GANG
My tip: use a push-stick to feed stuff into a saw. Like how important is it to use your bare hand like a boss vs. finishing your workday with all your digits?
well, fingers grow back, don't they?
@@pedrorserra only the uneven numbered ones
2,4,6,8 and 10 are gonners
He missed a part about respirators. Some come with cartridges that only filter out air born particles while others filter out the fumes as well. Don't assume you are safe just because you're wearing a respirator.
any good reccomendations on relatively cheap and COMFORTABLE respirators for fumes?
@@camit6237 I think bloggers should test bcmask masks. I think the masks of this brand are very cost-effective!
I've always use my respirator for cleaning out our dust collector and any high particle removal. I've also noticed it also grab those fine dust particles that most cheaper dust mask won't grab
I had my gc buy one for me to pop a hole in the concrete foundation wall with a Roto hammer in a crawl today. Didn’t want to do the concrete in that closed space without it even a dust mask I trust a respirator more
He took off his cap!
Yep, never know when you are going to see a someone take it off for the camera.
its cool how that type of mask doesnt stop chemicals but works great for disease!
Kino
Aren't all filters different? For respirators you can get particulate filters and solvent filters. They've also got their ratings for how effective they are at filtering.
Yes, the point was that dusk masks do nothing against gases, only solids.
That's what I was thinking. It definitely should have been brought up. So people don't think just because you have a respirator it will keep you safe, if you have the wrong filters.
Dust mask for particulate.
Black-banded respirator for chemicals from paint, epoxy, etc.
Pink-banded respirator for welding.
The 3M half-face respirator is so inexpensive and replacement filters reasonably priced, that there shouldn't be a question on what to purchase. Furthermore, the re-usable respirators are designed to be washed for a sanitary experience. I've used the N95-class filters for plenty of wood and resin composite dust generating activities over the past several years, and they work great.
Yeah but 3M stuff wouldn't fit under a welding helmet.
Got the respirator, ear muffs, eyeball sheild, and knee pads, how many condoms should I have on?
Only one, more than that and there's a risk of tearing.
@@zoeb7654 Better yet, no condom, My boy!!! You only need protection for your respiratory system when [[[[[[ banging a goat ]]]]]]]... Trust me, I've know guys who've used this technique flawlessly for decades - Goat is a great piece of ass, but stinks like shit.
A bakers dozen at least
What you are protected against depends on what type of cartridge you buy. There are a whole lot of different types of them. It starts with identifying what you are protecting yourself from.
Get a long garden hose and put one end in your mouth and one end outside 👌🏻
#LifeProTip
and make sure to not only inhale through the hose but exhale into it, too, so that natural selection can take its course
Indeed, you'd just be pushing the same stale air back and forth with that length of tube. That's why snorkels are so short. :)
+SparrowHawk183 snorkels are short because after just a few feet under water the pressure difference would make it impossible to breath.
Good idea until someone steps on the hose while you're using it.
I use the straps on my respirator to train myself to unhook bras
One day, you may be able to put your practice into use.
theclerksays best comment and reply ever!!!!!
Lol
It's not the same closure, so your training will be in vain :P
Ken Smith It’s really not hard lol. My Fiancée damn near always makes me undo her bra for her it’s just repetition.
What works the best against fumes, mold, pathogens and viruses???
maybe military gas mask
coronavirus huh? XD
i love Frank's insistence on "vacation" in these videos
How to change the toilet paper next time.
awhhh nawhhh. To be fair its not as bad as the time they demonstrated how to put paper on a table so you don't get it messy. I think they took that video down as I can't find it haha
So simple yet so relevant to my personal life. I was just thinking about these after painting my car with rattle cans. Gotta pickup a good respirator after watching this video
If you use it or not, make sure you check the seals on your respirators every three or four months and keep at least two changes of filters in stock at any time. Certain kinds clog very quickly.
What about preventing secondhand smoke from ciggarettes?
I've tried an N95 mask and the respirator (along with the cartridge attached and it was not expired) exactly like the 2 you showed in this video and both of them did a horrible job with protection
I've read some of the comments you guys posted and some of you said if you have a beard, you should stubble it or shave it off. I might stubble mine and see what difference it makes with protecting me from smoke
If your respirator is letting in smoke I would guess it isn't sealing, if you have a beard then that's almost certainly the issue, a smooth gasket cannot possibly seal against a coarsly fibrous surface. Smooth gaskets seal against smooth surfaces, like bare skin.
Thanks guys for your helpful tips 👏
Hey tested, you should do a video about fiberglass basics (either in shop tips or as a separate category). I've looked online multiple times to find a good tutorial but no one ever covers all the unexpectancies like fiberglass getting stuck to your gloves because of the resin on them or the resin drying too quickly, or the fiberglass not staying in place (all these are things I've experienced) , etc. From what I've found relating to fiberglass tutorials is that most of them all rely on some sort of basic knowledge about fiberglassing which I have been unable to find. If you guys could do a video hopefully solving all the problems I've had that would be great.
You also want to use the respirator if you are going to be heating galvanised metal (for example welding to galvanized steel) the galvanization gets in the the air and it might give you metal fume fever
"no sick leave for safety" is the name of my cyber industrial band, we play tonight at the Winchester tavern
Hey I have that same Winchester Tavern shirt. Neat.
So plz sir is it safe for sanding... i do polyurethane...
Coronavirus has made masks review videos popular
Full-faced respirators or half faced ones are the only ones I actually recommend.
This is helpful. Thanks
There are some experienced people in the comments, so I have a question:
I do trust Frank, industry professional and all that, but can anyone confirm what he's saying, That you need an IN-Organic vapour filter for spray paints and solvents.
I'm ordering a 3M respirator and everything in their documentation says you need an ORGANIC vapour filter. It specifically says for spray painting, solvents, glues, epoxy & fiberglass resin to use an Organic filter. It only recommends and inorganic filter for working with Sulfur Dioxide :/
So, was it a slip of the tongue or does Frank have some insight I can't find in the documentation?
did i say in-organic? yes, that would have been a slip of the tongue.
The man himself!
Thanks very much, that put's my mind at ease :)
I was an auto painter for many years, so maybe I can help. Here's a simple test; If you are using a respirator, and you can still smell the chemicals you are working with, It's not working. You should not be able to smell anything, at all. If you are spraying a substance that has a catalyst, such as epoxy or automotive polyurethane, you should go to a "supplied air" type of respirator. This type actually uses a line from a compressor to supply fresh air to the mask, hence the name, "supplied air respirator". Hope this helps.
+Richard Darlington ok, good to know. I figured as much, that you'd smell if it wasn't working.
I didn't know about fresh air respirators so thanks :)
Here's a link if you want to know more about the use, maintenance, and ratings of respirators. You could also search OSHA respirators.
www.osha.gov/dte/library/respirators/faq.pdf
Good for intensive exercise the respiratory one. As you breathe better for exercise without pollutants.
really good info to know. my girlfriend runs a bath product business and all the dust has been concerning me, wanna get some better respirators to protect us from all the particles flying around and also from the SLSA dust, that stuff burns :( definitely don't want us to mess up our lungs
Safety never takes a siesta
Ahh, the 3M 8511 the best basic dust mask because of that exhaust valve.
Anyone know what shirt Norman is wearing or where I can get one?
THANK YOU SO MUCH FOR THIS!!! Can you talk about safety when making molds and casting?
I resisted buying a respirator for a long time because I thought the resistance on the inhale would agitate my asthma, I couldn't have been more wrong, I breath better with it on than off even outside the shop because of the complete lack of dust or allergens. I'm surprised you didn't mention the cost savings of replaceable prefilters especially after knocking one off lol
Thanks for the tip to "pinch" the dust mask! I didn't know that!
Will the white respirator work for silica, or drywall? How often to replace those cartridges for the white one?
Pro tip from a chemically sensitive person that's gotten alot of use out of these things: Buy a true vacuum sealed coffee container like the one at (www.amazon.com/gp/product/B01NACX4YQ/ref=oh_aui_search_detailpage?ie=UTF8&psc=1) and whenever you're done, pop the cartridge off and put it inside. Seal it. It WILL store for longer, I promise you that. There's no air coming through it, no depletion of filter. And when you put the catridges back on, there are little notches on the cartridge that line up with that 3m mask shown in the video. They both attach clockwise. Hope this helps someone! I buy the 3m P100 pink cartridges, they are about $20 a pop, nice to save them as long as you can.
Just don't try to cheap out on your own health.
Great! More Shop Tips and espacialy savety Tips!
Simple but good advice.
whatre those plastic bits on the ends of the filters?
respirators come in three flavors: half face (seen in video), full face (includes built in goggles), and forced air.
Forced air has a battery powered fan which helps pump air through the filter. This is great for ppl with weak lungs, or if you need to be in it continuously for several hours.
Don't forget supplied air., you can have the mini tanks on your back
I've been wondering this for a while, because I though one was just a cheaper version of the other, thank you so much. At what point should one start using a respirator rather than a dust mask? Thank you!
They already mention it in the video but dust masks are for keeping out dust or particles, and respirators are for solvents.
If you're just sanding things, a dust mask is probably fine. If you're painting or using things that give off harmful fumes, you want a respirator. Even if you're just using spray cans outside! Safety first!
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal. There is a seal / fit test for respirators - put mask on without fillets, put hands over inlets and inhale (the mask should suction to your face if not there is a leak), then cover outlet and breath out (the mask should kind of inflate/bulge before air escapes)
I just use a respirator as you can get particulate filters without the solvent filtration. possibly not add cheap for a diary only solution but soo much more comfortable. also technically with all dust masks and respirators your not meant to have stubble or a beard as this can affect the seal.
Right on it .. thank you for the video
Should of talked about recommendations for good brands and some that you know aren't good brands.
Thanks for the video bro
I've got a safety question for you guys of Tested: what do you do about eye protection when you wear prescription glasses? And I can't deal with the double glasses thing, haha. I'm looking for some type of safety-prescription glasses fusion, any recommendations? :)
So would the respirator work good for welding stainless and other welding procedures or would the dust mask be fine?
wait what was that he said? 1:38 "inorganic cartidge"???
Hey Frank, any tips for stopping my safety goggles or glasses from fogging up whilst wearing a mask or respirator? Thanks !
I picked up the same respirator. Came in a set.
6200 + 6055 + 5935 + 501
Fits really well and it's easy to breathe through.
Love it!
Another one of life's biggest mysteries finally answered!
Tested motto should be "Let me tell you how youre wrong" lol
I learned this the hard way after painting stain for multiple hours with a regular mask, I got very dizzy and sick later in the night
Who knew this was prophetic........
COVID 19 safety never takes a vacation.
I work with this "simalfa" a all natural glue ( spray gun ) I normally use the dust mask you showed . Should I be using that???
May i know what is the sizing of the respirator? Thanks!
Please suggest a mask in amazon for chemical lab work as per daily uses.
Talking about airbrushing there what type extractor unit do you guy's use?? I'm an avid plastic modeler and am on the hunt for a new one.
Is the dust mask good enough for demoing ductwork wrapped in pink insulation?
One of my chemistry professors in college used to say: "Safety is sexy"
She was in her 80's and absolutely hilarious.
hi frank i don't have a shop per say but I do some work with dermel tool. I have been told that I should get a face shield cause I work with metal, would the price of one be worth it even if I don't do it that often
Depends on how much you value your eyesight.
+109268 a lot and I do wear safety glasses
With a Dremel, safety glasses and a face mask should suffice. A face mask is needed because grinding creates fine dust that you can breathe in.
Any kind of abrasive wheel (on a dremel, grinder, etc) has the potential to break apart and shoot out chunks at high speed. When using these it's a good idea to wear a full face shield, and minimally you'd want to wear safety glasses.
slomatt I've had that happen to me, especially when using emery cutoff wheels. Also, the sparks you see when grinding or cutting metal are tiny, sharp bits of hot metal. If these get in your eyes, the can be very painful. In addition, dry grinding produces clouds of fine dust, containing particles from the object being ground as well as silicate particles from the burs. When cutting or carving wood, you get fine sawdust. None of these things belong in your lungs, so you should wear a face mask as well.
What kind of cartridge should you use for acids in electroplating processes? I recently quit because they weren’t following guidelines and didn’t have a fume scrubber in the bay as nickel chloride is quite harmful in the long term. Also note there was sulphuric acid fumes, hydrochloric acid fumes and copper sulfate fumes.
Is the 3m 6099 filter good enough? It seems to be the best they do...
I've used a 3M mask (like Frank's) with 6059 gas filters a lot, for working with acrylic glues and other nasty stuff. Problem is, my nose is kinda big, and although I use the large size, the mask won't seal completely near my eyes... and it's very exhausting and a bit painful to have the mask slighty press down on your nose if you wear the mask for a couple hours... Also a question... you talk about shelf-life on the filters... I suppose that is the use-before date? I'd like to know for how long you actually can use a set of filters with daily use? ( i noticed he said look in the manual...but i can't seem to find it in there )
I looked abit at 3Ms documentation and when it comes to gas-filters it seems you should replace them after 6 months or when you can taste/smell the gas. Whichever comes first.
More info here: multimedia.3m.com/mws/media/447121O/filter-change-out-brochure.pdf
I like doing spray painting, I do it outside, I use a Dust mask+shirt on top to seal it better, can I still doing that or I need to change to a Respirator?
These are a bit bulky for daily use. There are more compact options that offer similar protection as long as you know how to fit/wear them properly
devilbiss air hood supply fed respirator is my go to for painting provides cool fresh air and no issue with general facial hair not cheap but to set up. also cleanspace 2 respirator battery air fed perfect for quick work and no air line or expensive filters for fresh air it will also supplie cool fresh air with no obstructions infront of your view like most (respirators)have.
any advantages of using a single catridge vs a double catridge respirator?
Can you tell me if the respirator for M101 is as good as N100? I cannot find a N100 and I see an M1010.
Norm always good questions...
So bondo would definitely require a respirator yes?
Bondo off gasses pretty bad (the terrible smell) so I like to wear one just to stop that.
don't forget to clean your respirators so nothing starts growing inside them and makes you sick.
That is also true...
What brand is that respirator? .. and the number label of that cartridge?
What if I use a gas mask with a nato filter? Will that filter out as much of the "stuff" as a respirator?
Haii I would like to know the brand name of that respirator and where can I buy...can u help me
So respirators also work with working with diesel / petrol fumes ?
Can you recommend the best respirator? Thanks.
That would be extremely painful.
M J ???
I dearly love my full-face respirator. They're a bit pricey, but the fact that it keeps solvent vapour out of my eyes is worth it. It's the same as the paper mask vs half-mask respirator - safety glasses might keep some of the particles out, but the solvent just wafts right around.
As far as brands, just go buy a 3M one. You'd be hard pressed to find a company less likely to go out of business.
Do you need a respiratory if spray painting outside
What is the height and body weight of that person wearing the respirator? I have hard times which size bes suits me.. kindly help. Thanks!
Are dust mask filters reusable? ex.cleaning with shop vac or soap and water. (the black strap base with filter add ons for wood dust).