How To Replace Tail Light on a 2007-2011 Toyota Camry
Вставка
- Опубліковано 7 лип 2020
- Hey guys! Here's a video on how to replace the tail light on a 2007 through 2011 Toyota Camry. Hope it helps!
Below is the link to the tail light. The link is for the driver side tail light. make sure you get the correct tail light for the side that you need to replace.
Tail Light Link:................ bit.ly/2O9AdVw
(Drivers side)
My Giveaway Video!:..... www.youtube.com/watch?v=OdYUF...
NEW Shirt with map:..... amzn.to/2UwIVjn
Shirt With My Face:....... amzn.to/2P6IpHs
AQUAMIGOS MERCH:
Aquamigos T-Shirt:........ amzn.to/31p9vfP
Aquamigos T-Shirt UK:.. amzn.to/32t3dxh
Aquamigos T-Shirt DE:.. amzn.to/32wA2ZW
Check out my cover of Ransom by Lil Tecca: bit.ly/2MUzGpn
SOCIAL MEDIA
Facebook:..... bit.ly/2uZxoNk
Instagram:.... bit.ly/2z1Jibu
Twitter:........... bit.ly/2TDFBCa
SnapChat:...... hiimtobias
SoundCloud:.. bit.ly/2UaMDNE
Song credits: Feel by Generation Lost Artlist
#taillight #toyotacamry #taillightinstall
Disclaimer: This video is for entertainment purposes only. Tobias Holenstein assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Tobias Holenstein recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Tobias Holenstein, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Tobias Holenstein. - Авто та транспорт
thanks man! i’m going to the junkyard tomorrow to try and find myself one of these tail lights. same side broken as the one you showed, so that was very helpful. can’t pass state inspection until it’s fixed and not shattered. thanks again!
Glad I could help! Best of luck with your car and everything! 🙌
This was AWESOME! Thank you for taking the time to help us all out.
Thank you! It's my pleasure 🙌
Super helpful vid, I'm buying myself a Camry today and am planning on getting some aftermarket tailights
I gotta say you had me crying when you didn't realize 10mm was 3/8 😂😂😂
Nice! Enjoy your Camry! Haha yeah, now I know 😂😂
Thank you for your time to make this video available to anybody" Do It yourself " replacement of tail lights part very 👍 good job
Helpful video! Keep up the great work
Thank you Baily!
Just what I was looking for....thank you!!
Glad I could help 🙌
You make it look so easy and saves me money from going to the shop
Great video!
Tobias: very helpful video. Thank you
You're welcome! Glad I could help :)
Replaced mine on 2011, it did help although on this model the location and types of clips and screws were a little different. Thanks for posting it in detail.
Thanks for letting me know, I thought they were all the same
Tht was straight to the point. Tq very much👍👍
You're welcome!
Very helpful, now if only you could just come and do mine for me haha
Haha you got this!
I just saw other videos where they did not have to remove the back bumper... just wondering why you needed to remove that .. great video
Yeah, after I made this video a friend of mine told me I could have just loosened that side of the bumper instead of completely dropping it. Pretty much there is a clip on the bottom of the tail light that kind of fits into the bumper, so that's why you need to either remove it or loosen it
Great Video. Thank you. There are a number of variations with Camrys. Mine is a hybrid. The tail light assembly comes with the black clip on the bottom (which you pointed to) and you definitely have to remove the bumper because the black clip will not detach (without a great deal of force) from the light assembly as happens with other models. Next, there is a white bulb connector that you have to disconnect. You do this by inserting a small flat edge screwdriver into the connector on the wall side of the tail light. This is inconvenient because you can't see how the connector disengages and comes apart.
6:48
Thanks bro got all the calls out I couldn't figure out why I wasn't coming out then you mentioned how you had to take the bumper off
Awesome! Glad I could help!
AWESOME video....good job (I LIKE)
Thank you! 🙌
Super helpful and well done. Could use brighter light on one section.
Thank you! I'll try to figure out some better lighting next time
Great job 👏
Thank you!
بہت خوب عزیزم. اچھا کام کیا
Good video
On my 2011 Camry LE, the 2 clips inside the trunk (on the left and right) didn't have a Phillips screw, instead they have a center push button. Push it in and pull the clip out. I also got hung up on the bolt that is covered by the wire harness 🙄 (was wondering why the light wouldn't come out!). The screws in the wheel well are kind of difficult to line up. Some screws for me also didn't seem to get tight even though they seemed fully screwed in. Anyway, I think it came out great, thanks for the helpful video!
Glad I could help 🙌
Were all bolts able to be removed using only the 10mm socket wrench?
nice vid
Thanks Ivan!
When I took out the tail light there was no black clip so I don't need to remove the clip. A lot easier and no damage to bumper. Only my case?
Great vid, I couldn't find the one in the wheel wheel weld so I can to YT. Just wanted to mention that you don't need to drop the entire bumper of you are only replacing one side. If mentioned in the vid please disregard, once I found that upper wheel bolt I was gtg.
Oh yeah one of my friends was telling me the same thing. Like you can just bend it enough to get the clip out right?
@@TobiasHolenstein Correct, the left side drop down plenty enough for me to replace it. Still a good vid for those that might need to do both. I remember you mentioned some bumper damage. So I thought you might have taken it off to replace or paint.
Oh thank god you don’t need to remove the bumper. I got a used camry and the guy who had it repaired riveted the bumper to the car.
You never followed up with the black clip that the top edge of bumper guides into.
Is that a Celica in the garage?
how long did this take you?
Probably about an hour, but if I wasn't also recording the video I think I could have done it much quicker. Like maybe 30 mins. Some people have also told me that I could have saved some time by only loosening the bumper instead of removing the whole thing
thank you but i dont think you need to rmove the bumpert
You are probably right, a friend of mine was telling me I could have just loosened it instead of taking it completely off
Thanks for this tutorial homie you saved my dumb ass from spending an extra 200 dollars
Glad I could help 🙌
1 inch = 25.4 mm
3/8 inch = 9.525 mm almost 10 mm
My grandma backed into something and had the same kind of damage
Sorry to hear that! It's not too hard to fix 🙂
2007-2011?
Yeah basically the 6th generation Camry
At least run a test
Remove bumper to get access to the taillights…🤮
It is too trouble to remove the bumper. I just loose 3x screws , broken the old tail lamp casing, replaced the new casing but without the clip.
TO MANY BLABLABLA
I just saw a video of someone removing the tail light without removing the bumper? Im confused
A couple people have told me that they just loosened the bumper and didn't completely remove it. Maybe that's what they did in the video you saw