My 2010 SS 6MT threw a “AC off due to motor temperature”. I have a sct flash tuner to check the temps and everything is nominal. Plan on changing out the temp sensor but others have suggested resetting the ecu. Thoughts?
@@antoniowilson9855 i am almost 100% sure this issue is a software interruption caused by my SCT handheld. If I run the car without the flash tune, no problem. Its too bad my JLT short ram requires that tune to not run too lean. Yesterday the message came back on so i ignored it (i could not pull off the road and reset the ecu) and about 20 min later (the car now had a chance to reach op temps) the message went away and the gauges went back to normal. Anyways, i will get a professional tune once i bolt the headers on but until then, thanks for the input guys!
If I choose to do the reset with the negative cable on the battery in the trunk. The key should also be turned on to power correct ? Same as turning it on when doing the reset using the positive post under the hood.
Hello i like your video but i needed to ask you if this will work for a 2010 chevy camaro LT because I get a ob2 scanner reading that the communication with the ecm is lost so I'm wondering if I would need a new ecm/pcm what do you think about it?
@@camaromodschannel thank you for responding to me and I don't even know where that is so I never messed with it but this video shows that I did have the car working and I will also send you another video on what it's doing now ua-cam.com/video/eUI7dSDUEAI/v-deo.htmlsi=vKyCP3Gs5-TLtnMD
@@camaromodschannel hello buddy I got the last video I wanted to show you about what my car is doing like I said I would get the link for you to see but I will try what you showed me in your video to reset the car computer! I just hope it 🙏 works to fix the issue 🙏 ua-cam.com/video/LBDAAmKrGzQ/v-deo.htmlsi=x8q9SDsuS7neTi8W
Just to verify I’m doing this right, I leave the key in the on position the entire time disconnect the power cable and remove those 2 fuses and leave it set for 15-30 min before connecting the power back?
Your car not running right, mainly the radio acting weird not working correctly. Reset the engine light after 10 minutes. Yes, for majority of car with a computer. Thanks.
@@camaromodschannel Is this method something to do instead of disconnecting the negative battery terminal for a few mins? I figured disconnecting the battery would achieve the same results but I could be wrong. Thanks for the info.
Can I ask you a question? 2015 Camaro SS M6. I have service power steering populate but ABS doesn’t connect to clear the codes. Now code U0109 for fuel pump and U0073 for can bus communication in my code reader. I hope these are sensors but would love your insight!
Hello, How old is your Battery? sounds like you have some problems with your car. are you running at reduced Power? I think your sensors are fine, sounds like a power problem. Battery or bad ground. ect. Faulty CAN communication system, posible replacement. CAN System harness is open or shorted CAN System circuit poor electrical connection, Check your grounds. also check your throttle body any problems here can throw all kinds of codes.. Thanks. Roger
@@camaromodschannel Hey there! Thank you for replying! Just bought a new battery 6 months ago and no it still has full power but I will look/clean the throttle body and look around the grounds. I found this black wire underneath my dash but I can’t find where it goes so going to bolt it on somewhere and see what happens!
I have two check engine codes for the upstream o2 sensors i replaced them twice still have an issue. Delayed response it says. As 1500 rpm the car will jerk and hesitate on decel and light throttle but not on more throttle. Cleaned the maf sensor as well. Car is stock besides cold air intake and scoop no headers. Don’t know what to do to fix it. Freeze frame data for the 02 sensors will always show speed of 120 to 140mph when I wasn’t going that fast and will show intake air temp of 0’degrees or really cold when it’s summer out… also short term fuel trims are 29. My Speedo seems fine and outside temp gauge works what’s wrong?
How old is your battery? A bad battery can cause allot of problems. Or a bad ground. Hard to diagnose over the internet. May have to take it to a shop that can fix it. Especially if its not running right. Thanks
Do you know anything about resetting they anti theft system on a 2014 Chevy ss. I’ve changed out my starter and my battery I have a check engine light for the break control module and also the rack and pinion all it’s doing is clicking won’t turn over at all
Have you checked your starter relay in your fuse box? You have to have a key in the door and unlock it 3 times back and forth to reset your anti theft.
If I unplug my ECM plugs (2) will I mess anything up as far as programming...I want to do this to clean the connections. I'm getting a random starting issue. My 2010 3.6L will start but after fiddling with fuses.
@@camaromodschannel much appreciated, I went out and cleaned everything. For some reason everything is leading back to the fuse 26 (front windows) perhaps something is grounding out ...The car will start after awhile but no signs of deficiency or constant drowning crank...It will just turn on randomly that is why it always leads to fuse box or ecu for me.
On my 2010 Camero ,the mechanic cleared the couple amber lights such as tire pressure and traction control lights with the computer ,now the car runs rough.it will starts and cut right back off giving Throttle body code . I know it has to do something with ECM?
Could doing this help with my blinker not working even after replacing entire tail light assembly? Blinker went out, we replaced and did upgrade and the blinker still doesn’t work. Checked the harness and the pin that matches turn signal isn’t lighting up with a test pen. Can’t seem to find a fuse that would be the problem so I’m wondering if resetting computer might help???
Hi.. I just bought a camaro from Out of State into California and its failed SMOG test.. I see 2 error codes : P0603 , P1258 I have an OBD bluetooth scanner and not able to clear with that. Will battery connect or Fuse reset trick work for it ? Thanks.
Hi, I have a 2010 Camaro SS that I’ve been fighting with a P0300 and P0205 codes for quite some time. I understand it to be a misfire from a code reader but have replaced all spark plugs and wires. Replaced cylinder 5 injector as well as the coil pack for cylinder 5. The car throws the codes after engine is warm and is driven for about 10-15. It seems like after the motor is warm on left hand turns or under heavy load I hear a misfire and it goes into LPM. Service stabiltrak comes on as well. Any insight you have on this is greatly appreciated. Thanks.
@@camaromodschannel unfortunately, cleaning the TB did not help in this instance. I drove the car about 10 minutes and CEL came on started flashing and the car almost stalled at a red light. Same codes being thrown. Any other thoughts as to what it might be? I know it may be a long shot, but the battery in the car is about 9 years old. I have read some forums where that could be a cause?! I’m reluctant on that thinking because it starts and idles fine until it’s up to temp and driving on the road. Any help is appreciated, Thanks.
My 2014 camaro v6 keeps going into limp mode with code p2138 and p2127. Ive already replaced pedal assembly, throttle body with sensor, and put in a new ECU and programmed it but I still keep getting limp mode. The code keeps popping up randomly after I remove it with my scanner sometimes it will last a day before or less before the code pops up again
pedal position sensor switch E has a low input. This looks to be a grounding problem, How is your battery? have it tested... You replaced about everything that is working around that trouble code. so LOOK at your body grounds, Thanks...
Stumbled upon this video while searching for codes P0641 & P0068 solutions. I've already replaced the MAP sensor, MAF sensor, Gas Pedal, throttle body and im still getting these codes while the car goes into limp mode. I have noticed I'm able to move my negative battery cable on the terminal even though it's tightened down as much as I can. I find that odd as im not removing the cable so often that ahould occur. And honestly it strange how it occurs. I can drive my kids to school, drive to work, drive home for lunch, back to work, then go pick my kids up. But as soon as i pick them up and start making left hand turns the car goes into limp mode. It literally always happens in the same areas on the way home. I ran into this issues about 8 years ago and i ended up replacing the Throttle Body and that fixed the issue. However it hasnt this timr around. Any advice given would be appreciated if you ever do respond. Thanks!
@@camaromodschannel Going to look into that. My dad's friend has a similar issue with his Vette years ago. Turned out to be the battery cable. Really appreciate responding back! Thanks again.
You may have a short too ground those sensors are all on the same circuit meaning they share power and if one of them is grounding out they all lose power making you think it’s a bad sensor check over your engine harness for wear spots I suggest printing out the engine harness diagram
Well I have a weird problem that just started yesterday. I turn my car off and it stays on for a minute without the key in it? Now it says my battery charge system needs to be serviced and puts it in reduced power? Do you know what I'll need to buy, so I can get part by part. It's doing randomly? It's only done it one time today.
Hi! Does this work if radio has Bluetooth problems? It only works for Phone calls, not for music. I know there is one for Phone calling and one for music. It worked before, but after Winther hibernaition, it does not work. It can not connect. Sorry for my english, but hope you understood my problem.
Hi sir My camaro ss 2018 is dectecting 2 doors even thoe it’s a 2 door car haha on the passenger side and causing the lights to stay on is there anything I can do, can resetting the computer do the trick
Im having a problem it throws code that it’s the map sensor but im not sure where it’s located on my 3.6 liter v6 2017 camaro it runs rough and cuts off on hills
I did what you said in the video. Plugged the fuses back in and put the positive terminal back under the hood. And now I have reduced engine power and my car is running like shit.
Why did you look up this video if you weren't all ready having a problem with your car? I said one or the other, remove the negative or positive power from your battery, wait 15 minutes and try it again. Also check your throttle body and clean it.
I found this; it may help with your issues : Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time. The [COLOR=blue !important][COLOR=blue !important]instrument [COLOR=blue !important]panel[/COLOR][/COLOR][/COLOR] cluster (IPC). BCM and PCM must be in working order and the Passkey system repaired 1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The [COLOR=blue !important][COLOR=blue !important]SECURITY [COLOR=blue !important]light[/COLOR][/COLOR][/COLOR] will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine. If it starts and run, the system has reset. If it doesn’t start or run and release the key to the ON position and complete the rest of the steps. 5. The SECURITY light will illuminate. Wait 10 minutes until it [COLOR=blue !important][COLOR=blue !important]turns [COLOR=blue !important]off[/COLOR][/COLOR][/COLOR]. 6. Turn the key to OFF and wait 10 seconds. 7. Turn the key to ON and attempt to start the engine and release the key to the ON position. 8. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 9. Turn the key to OFF and wait 10 seconds. 10. Start the engine
Based on your description, it seems like there could be a problem with the blower motor or the blower motor resistor 1. The blower motor is responsible for blowing air through the vents, while the blower motor resistor controls the speed of the blower motor. If either of these components is faulty, it can cause the blower to make loud noises and then shut off 1. what year model is your car.. thanks
So my friend has a camaro... its randomly throwing a stabilitrak service light. It also will just randomly die while in drive. When he went to use his turn signal the vehicle locked it's doors. No turn signal came on. Just random electrical things. And it randomly happens so it's hard to get it looked at. No codes can be found. Unplugged both positive and negative cables to battery. Looked at the fuses they were fine. Sprayed the wheel sensors with air and the cold air intake with air. It just started a week ago. And his dad can't figure it out. Do you have any ideas?
How you doing bro I have a 2011 Chevy Camaro V6 my fuel injector went out I replaced all injectors spark plugs coils rail sensor all Upstream O2 sensors massive flow air sensor and still getting a rich idle code do I have to reset the computer the valves are not that dirty actually they're pretty clean thank you for your time
Not a code issue but I’ve been chasing a problem for awhile. Maybe you will have time to respond. Right brake and blinker out Left front blinker out. All bulbs are good Don’t seem to have power to the harness on the right rear that controls the brake and blinkers. All running lights are good
Funny thing is it’s just my blinker. All other functions work. Inside the harness it’s a 10 pin bc it’s an RS. On the pin that worked the turn signal I used a test light and it’s NOT lighting up. I don’t know where to start
I forgot that I posted this. Anyway I took the car to the dealership and although I checked every existing fuse on this car, even in the trunk they found that an entire fuse had fell from the fuse box. It was completely missing!!!!! They never found it but put one in the empty slot and I was back in business
I have a 2015 Camaro Ls I crashed the got it fixed but the guy didn’t mount up my computer for the car. It fell and burned a few wires. I fixed the wires but car does not start. The key turns but the car is dead. Battery is good. Can’t find any fuses blown. Can I get some advice please
Sounds like you had a short and burned something up, you say its dead, and won't turn over? You need to get it to turn over before I would recommend getting another computer.
Hey there I recently swapped engine 3.6 but when I turn the key it just clicks and got power to starter and battery but my radio and windows doesn't work just thought I asked thanks
Did it lost communication to the ecu? Cause I recently changed the engine for another v6 and every time I try to start it it does nothing but the moment I take out the key is clicks
My 2019 Ss got water in trunk wetting all the wires now my car giving all types code will not run took to dealer in they said I need to replace the body harness for $7000 the water damage the wires any help
I have my camaro set for when i open the door after shutting engine off, the dash lights turn off right away, (i dont need them on for 30sec or 1 min etc..) but now when i open the door to get out they stayed on even though in the settings i have it set to have the lights off right away, what could this be?
My camaro throws code 2230 and 2227, i switched out the map sensor and still throws the code, now my car drives and starts reduceing power but gauge sais im going a higher speed
2010 llt Camaro with a recently swapped 3.6 v6 only it came out of a Cadillac same block and heads it’ll crank once most of the sensors are connected but won’t start it throws codes only for TB p0698 p2119 p2176 p2101 please help!
Error Code P0698 is defined as Sensor Reference Voltage C Circuit Low, What the P2119 code means. This code indicates that the throttle valve is not in the position the PCM (Powertrain Control Module) expects it to be in What the P2176 code means. The P2176 trouble code indicates that the Engine Control Module (ECM) has detected that the throttle body actuator/motor has failed to learn the correct position at which the butterfly valve within the throttle body should be in order to produce a smooth idle for the engine.What Does the P2101 Code Mean? Diagnostic Trouble Code (DTC) P2101 stands for Throttle Actuator “A” Control Motor Circuit Range/Performance. It is usually triggered when your vehicle's powertrain control module (PCM) detects that the actual throttle position does not match the desired throttle position. also make sure you have a good battery. I would try swapping the throttle body, and see if that helps, or get the computer that goes with that engine.and try that. thanks.
@@camaromodschannel yes indeed I have checked most of the DTC’s that I can read with my obd2 scanner and recently today replaced the throttle body with a cleaned out one but the same 4 codes pop up still,so would this be for sure a computer replacement situation or could I still salvage the one already hooked up by resetting it?
Appreciate your videos. Question...randomly getting check engine light, but OBD scanner often says "no codes". Yesterday while highway driving at 70 mph sudden misfire and a 0007 code...misfire went away...cleared code and car began running better than it has in months. Any ideas?
I recently bought a 2012 Camaro with a 3.6 V6. The check engine light came on and the door ajar warning came one and stayed on. The alarm quit working and the drivers window wouldn't roll up. I replaced the door locking actuator and everything went back to normal but the window. I replaced the switch and it worked for a few minutes and quit. Now I'm back at square one. When the check engine light was on I took it to AutoZone and they said the ECM was bad. What can I do to fix the problem I'm having??
@@camaromodschannel plus communication to the transmission control module and also the body control module and also the engine control module and it through one for the can bus communication. I had codes for all my wheel speed sensors and I replace them today, but it was still seeing the codes and it also said incorrect immobilizer identifier received.
@@camaromodschannel but when I reset the Tcm buy starting it up and shut it off and waiting. I did that five times, and the check engine light went off. I just did that like five minutes ago.
@@camaromodschannel but I do have a question about the antilock brake system. He gave me a secondary DTC and it says it lost communication with the electronic brake control module. Now is that the part that’s under the hood on the left-hand side with the four lines running to it
I got a service theft deterrent system msg and my car turn off randomly when I’m driving and not just that I have to disconnect my battery every time it happens got any advice
I have see that problem before, check your throttle body. Clean or replace, if you have a tb you could try out from another car so you can know that's the problem. Thanks
2016 Camaro ss starts an idles for 5/10 seconds then says anti-theft then dies. Have & programmed new key starts the car up but doesn’t unlock doors. All keys lost.
I replaced my window regulator in a 2015 camero and it still does not work already try re cabrating and even returned window regulator and got another new one same thing don't work ? Help!
So what if I replaced the throttle body with new sensor and pedal position sensor and also replaced 02 sensors and did the reset and cleared the codes with handheld scanner and still get the same codes???
5th gen camaro, new starter and new battery, added grounds. Hot start issue which throws the stabilitrack codes. After cooling off it starts fine. Been happening for years. 😅. I really do wish I could find the fix.
I will try this because my check engine light is on . The code said oil pressure sensor. I change it out had the mechanic clear the code out and drove it for about a week and now the dam check engine light is back on. I checked the oil it’s good Now I am at a lost to what it could be now. I had AutoZone put it on the code reader and it said engine oil pressure sensor range/ performance. I went and bought another new oil pressure sensor because I was thinking maybe the one I bought was bad also. So any way if this has happen to anyone or if anyone can help me I would be thankful. My care is a 2014 SS Camaro.
@@camaromodschannel tried to do that and still won’t turn on. Battery is good. And I tried the method of reprogramming the key. ON position for 10 mins and off 3 times repeated but no luck
Wow those are hard to figure out sometimes. Have you cleaned the throttle body in a while, may not fix it but just another thing that's not a problem. Those things cause so many problems but they throw codes also. Thanks
My 2013 v6 I get stabilitrak and then it misfires on cylinder 1. Runs rough. Also, sitting in park while it is running rough I put the accelerator to the floor to see if it would rev and it revs up and down on its own with peddle all the way down. What is wrong with this sob?
My car cranks but doesn’t start my fuel pump and high pressure fuel pump working switched out my crankshaft position sensor as well and still don’t turn on , got all these codes ,P062b,u0100,p025A,p0107 what should I do now ?
Just say remove number five and number 20 fuse for 15 minutes to a half hour resets the computer in case you get bad gas and put it back to 91 tune if we pull out five and 20 fuse resets it back to 93 tune if that’s what you have
Sounds like something broke, not sure. Make sure your car is on level ground. Might be a micro switch in the shifter stoped working. Have you had trouble with your shifter before?
That is your sensors in your back bumper when you get close to something it will sound. I would just check and see if it's still working. May have a sensor you need to replace. You can get them from ebay or your local Chevrolet dealer. Thanks.
@@camaromodschannel even though it says service stability track and parking assist when it happened everything in the dash went to zero I don't know I think it may be a body control module how do you reset one or do I have to buy a brand new one
Insert the key in the door lock all the way and then turn the key to unlock your car door, but don’t release it. You want to hold the key in the unlock position for twenty to thirty seconds. This lets the car recognize that you have the right key and will disengage and reset the system.
Ok i am getting a "reduced engine power message" But have zero engine lights, zero codes and the car has full power and runs great. i just get that message pop up every 2mins and it is very annoying Plz help me someone!!
@@camaromodschannel ok i also put it a the dyno and ever since then i started i checked with scanner and seen EBS Eletronic Brake system communication error. i tried resetting the abs system the whole computer system and nothing?
@@camaromodschannel 2010 rs camaro v6 , I haven’t checked started I tried starting it with a dead battery n I could hear the starter but it’s jus dead silent I was thinking ecm but idk man shits a headache n was jus trying to get pointed in the right direction anything at this point helps , thank you !!!
@@camaromodschannel I will try that and hopefully it fixes it I’m jus not sure cuz last night it cranked for like a second then stopped cuz the battery was dying but I charged it today and nothing no crank or nothing
Pro tip: watch this video at 1.5x speed
Yes,
1.75 haha
2x
No joke!!
3x
Has anyone ever told you that you look like captain kangaroo...I can't be the only one.☮
Yes, I get that all the time. Lol thanks.
Finally a Camaro related video
Yes, thanks for your patience.
thank you, I"m auto illiterate and just bought a 5th gen. Show me the way Sensai . thanks again.
Thanks
Great video, thank you!
Glad it helped! Thanks..
Good info, 👍
Thanks.
My 2010 SS 6MT threw a “AC off due to motor temperature”. I have a sct flash tuner to check the temps and everything is nominal. Plan on changing out the temp sensor but others have suggested resetting the ecu. Thoughts?
I would change out the temp sensor, you can reboot the ecu by disconnect the battery cable 15 min. If its normal i wouldn't worry about it. Thanks.
I changed back two sinsor two that was the only problem
Awesome
@@antoniowilson9855 i am almost 100% sure this issue is a software interruption caused by my SCT handheld. If I run the car without the flash tune, no problem. Its too bad my JLT short ram requires that tune to not run too lean. Yesterday the message came back on so i ignored it (i could not pull off the road and reset the ecu) and about 20 min later (the car now had a chance to reach op temps) the message went away and the gauges went back to normal. Anyways, i will get a professional tune once i bolt the headers on but until then, thanks for the input guys!
Do i have to take off the sensors and the positive cable in order for it to work? Or just with the positive cable will work? Thanks!
No just the positive cable, thanks
If I choose to do the reset with the negative cable on the battery in the trunk. The key should also be turned on to power correct ? Same as turning it on when doing the reset using the positive post under the hood.
Yes, 15 minutes battery disconnect should help. Thanks
@@camaromodschannel Worked perfectly, thank you sir.
Hello i like your video but i needed to ask you if this will work for a 2010 chevy camaro LT because I get a ob2 scanner reading that the communication with the ecm is lost so I'm wondering if I would need a new ecm/pcm what do you think about it?
Yes, sounds like you have a problem between the ECM and the body control module. Thanks check your connections..
@@camaromodschannel thank you for responding to me and I don't even know where that is so I never messed with it but this video shows that I did have the car working and I will also send you another video on what it's doing now
ua-cam.com/video/eUI7dSDUEAI/v-deo.htmlsi=vKyCP3Gs5-TLtnMD
@@camaromodschannel hello buddy I got the last video I wanted to show you about what my car is doing like I said I would get the link for you to see but I will try what you showed me in your video to reset the car computer! I just hope it 🙏 works to fix the issue 🙏
ua-cam.com/video/LBDAAmKrGzQ/v-deo.htmlsi=x8q9SDsuS7neTi8W
Check your ground wires. That might be hard to figure out. Thanks
Just to verify I’m doing this right, I leave the key in the on position the entire time disconnect the power cable and remove those 2 fuses and leave it set for 15-30 min before connecting the power back?
Yes, that's fine, you don't need to take out the fuse if you disconnect the positive cable. Thanks
What scenario would I want to reset my computer?
And is this similar for gen 6 camaro SS (2018)?
Your car not running right, mainly the radio acting weird not working correctly. Reset the engine light after 10 minutes. Yes, for majority of car with a computer. Thanks.
@@camaromodschannel Is this method something to do instead of disconnecting the negative battery terminal for a few mins? I figured disconnecting the battery would achieve the same results but I could be wrong. Thanks for the info.
@@Mangotheconure yes, either one will work. thanks.
Can I ask you a question? 2015 Camaro SS M6. I have service power steering populate but ABS doesn’t connect to clear the codes. Now code U0109 for fuel pump and U0073 for can bus communication in my code reader. I hope these are sensors but would love your insight!
I'll look into this, you will give me a day ot two. Thanks
Thank you! I appreciate it
Hello,
How old is your Battery? sounds like you have some problems with your car.
are you running at reduced Power? I think your sensors are fine, sounds like
a power problem. Battery or bad ground. ect.
Faulty CAN communication system, posible replacement.
CAN System harness is open or shorted
CAN System circuit poor electrical connection, Check your grounds.
also check your throttle body any problems here can throw all kinds of codes..
Thanks. Roger
@@camaromodschannel Hey there! Thank you for replying! Just bought a new battery 6 months ago and no it still has full power but I will look/clean the throttle body and look around the grounds. I found this black wire underneath my dash but I can’t find where it goes so going to bolt it on somewhere and see what happens!
Following up on this! Turned out to be a bad ground wire by the fuse box tightened her up and back at 100%!
I have two check engine codes for the upstream o2 sensors i replaced them twice still have an issue. Delayed response it says. As 1500 rpm the car will jerk and hesitate on decel and light throttle but not on more throttle. Cleaned the maf sensor as well. Car is stock besides cold air intake and scoop no headers. Don’t know what to do to fix it. Freeze frame data for the 02 sensors will always show speed of 120 to 140mph when I wasn’t going that fast and will show intake air temp of 0’degrees or really cold when it’s summer out… also short term fuel trims are 29. My Speedo seems fine and outside temp gauge works what’s wrong?
How old is your battery? A bad battery can cause allot of problems. Or a bad ground. Hard to diagnose over the internet. May have to take it to a shop that can fix it. Especially if its not running right. Thanks
Battery is 1 or 2 years old. I put in a better rated agm than the original factory lead acid battery.
I would take it in if you can't figure it out. Wish I could look at it. Thanks
What about reading the code U0401 ecm/pcm and stabilitrak issue Will this work also? 2016 Camaro SS
That code is invalid data. Check and or replace your battery. Thanks
Do you know anything about resetting they anti theft system on a 2014 Chevy ss. I’ve changed out my starter and my battery I have a check engine light for the break control module and also the rack and pinion all it’s doing is clicking won’t turn over at all
Have you checked your starter relay in your fuse box? You have to have a key in the door and unlock it 3 times back and forth to reset your anti theft.
If I unplug my ECM plugs (2) will I mess anything up as far as programming...I want to do this to clean the connections. I'm getting a random starting issue. My 2010 3.6L will start but after fiddling with fuses.
No it is an eprom chip that the code is burned on so as long as you don't short it out you will be fine. Just disconnect the battery. Thanks
@@camaromodschannel much appreciated, I went out and cleaned everything. For some reason everything is leading back to the fuse 26 (front windows) perhaps something is grounding out ...The car will start after awhile but no signs of deficiency or constant drowning crank...It will just turn on randomly that is why it always leads to fuse box or ecu for me.
On my 2010 Camero ,the mechanic cleared the couple amber lights such as tire pressure and traction control lights with the computer ,now the car runs rough.it will starts and cut right back off giving Throttle body code . I know it has to do something with ECM?
No a throttle body code is a throttle body. Do you have one you can swap it with? Another throttle body.
Could doing this help with my blinker not working even after replacing entire tail light assembly? Blinker went out, we replaced and did upgrade and the blinker still doesn’t work. Checked the harness and the pin that matches turn signal isn’t lighting up with a test pen. Can’t seem to find a fuse that would be the problem so I’m wondering if resetting computer might help???
Have you checked the body control module? That's what I would check, if you replaced all those parts. Thanks
No I haven’t. I’ll have to look that up. I don’t even know what that is or where it’s located
@@renpal2173ifybcm are in the 3 fuse boxes. 1under the hood 1 left side of dash end cap 1 in the trunk on passenger side wall
Hi.. I just bought a camaro from Out of State into California and its failed SMOG test..
I see 2 error codes : P0603 , P1258
I have an OBD bluetooth scanner and not able to clear with that.
Will battery connect or Fuse reset trick work for it ?
Thanks.
Yes, Disconnect for 15 minutes and it will clear the codes for a little while.thanks
Hi, I have a 2010 Camaro SS that I’ve been fighting with a P0300 and P0205 codes for quite some time. I understand it to be a misfire from a code reader but have replaced all spark plugs and wires. Replaced cylinder 5 injector as well as the coil pack for cylinder 5. The car throws the codes after engine is warm and is driven for about 10-15. It seems like after the motor is warm on left hand turns or under heavy load I hear a misfire and it goes into LPM. Service stabiltrak comes on as well. Any insight you have on this is greatly appreciated. Thanks.
I would clean the throttle body first thing. those TBs can cause so many codes by just being Dirty. and Service stabiltrak is one of them..Thanks
@@camaromodschannel Thank you!! I will try that and see if it makes a difference!
@@camaromodschannel unfortunately, cleaning the TB did not help in this instance. I drove the car about 10 minutes and CEL came on started flashing and the car almost stalled at a red light. Same codes being thrown. Any other thoughts as to what it might be? I know it may be a long shot, but the battery in the car is about 9 years old. I have read some forums where that could be a cause?! I’m reluctant on that thinking because it starts and idles fine until it’s up to temp and driving on the road. Any help is appreciated, Thanks.
Did you ever find out what the issue was having the same problems right now
@@Brian519-yk7rw Did you replace the Battery? Do you have a Battery Tester?
How do you leave a pushbutton start cars key on? Go to the accessory setting?
Yes. Go to the accessory position. Thanks..
My 2014 camaro v6 keeps going into limp mode with code p2138 and p2127. Ive already replaced pedal assembly, throttle body with sensor, and put in a new ECU and programmed it but I still keep getting limp mode. The code keeps popping up randomly after I remove it with my scanner sometimes it will last a day before or less before the code pops up again
Ok. Let me look into this. I'll see what I can find. Thanks
pedal position sensor switch E has a low input. This looks to be a grounding problem, How is your battery? have it tested... You replaced about everything that is working around that trouble code. so LOOK at your body grounds, Thanks...
I have this same code p2127 plus a p2121 curcuit d and e plz help replaced battery and position pedal 😢
Sorry fell asleep 3 times before you actually showed me anything
Sorry drink some coffee. I get paid by the hour, you know I don't even have to make these videos! How about I delete this one! 😆 🤣 😂
When disconnecting the positive from the hood you leave the car on right not the engine on? Jus making sure dont want to mess the car up...😅
Yes, Don't have the car running or it won't do any good. Thanks
Does this work as well for “break assist message”??
Is your check engine light on? Have any codes? Wouldn't hert to try, but if it comes back you have a problem of course. Thanks
Do we have to keep the key on ,when we take both fuses out for 15 mins ? Thanks
No, thanks
What fuse is for the lights on the door for the camaro Rs package
Under the fuse cover tells you what fuse is what. Thanks
Stumbled upon this video while searching for codes P0641 & P0068 solutions. I've already replaced the MAP sensor, MAF sensor, Gas Pedal, throttle body and im still getting these codes while the car goes into limp mode.
I have noticed I'm able to move my negative battery cable on the terminal even though it's tightened down as much as I can. I find that odd as im not removing the cable so often that ahould occur.
And honestly it strange how it occurs. I can drive my kids to school, drive to work, drive home for lunch, back to work, then go pick my kids up. But as soon as i pick them up and start making left hand turns the car goes into limp mode. It literally always happens in the same areas on the way home.
I ran into this issues about 8 years ago and i ended up replacing the Throttle Body and that fixed the issue. However it hasnt this timr around.
Any advice given would be appreciated if you ever do respond. Thanks!
That is what I was going to suggest was a throttle body, that thing cause so many problems, just check your grounds. Thanks.
@@camaromodschannel Going to look into that. My dad's friend has a similar issue with his Vette years ago. Turned out to be the battery cable. Really appreciate responding back! Thanks again.
You may have a short too ground those sensors are all on the same circuit meaning they share power and if one of them is grounding out they all lose power making you think it’s a bad sensor check over your engine harness for wear spots I suggest printing out the engine harness diagram
@@DIYPeformance thanks, turned out to be a wire chaffing against a bracket.
Well I have a weird problem that just started yesterday. I turn my car off and it stays on for a minute without the key in it? Now it says my battery charge system needs to be serviced and puts it in reduced power? Do you know what I'll need to buy, so I can get part by part. It's doing randomly? It's only done it one time today.
Need to check your alternator, and test your battery, sounds like a low voltage problem. Thanks.
@@camaromodschannel thanks
Hi! Does this work if radio has Bluetooth problems? It only works for Phone calls, not for music. I know there is one for Phone calling and one for music. It worked before, but after Winther hibernaition, it does not work. It can not connect.
Sorry for my english, but hope you understood my problem.
Try another phone, to see if you can connect, you may have a problem with your radio. Thanks
@@camaromodschannel well, I have tryed 5 different phones. 2 iphones and 3 samsung galaxy
Hi sir My camaro ss 2018 is dectecting 2 doors even thoe it’s a 2 door car haha on the passenger side and causing the lights to stay on is there anything I can do, can resetting the computer do the trick
Sounds like a switch? Thanks
Im having a problem it throws code that it’s the map sensor but im not sure where it’s located on my 3.6 liter v6 2017 camaro it runs rough and cuts off on hills
Somewhere on the intake manifold. Towards the back. Thanks
I did what you said in the video. Plugged the fuses back in and put the positive terminal back under the hood. And now I have reduced engine power and my car is running like shit.
Why did you look up this video if you weren't all ready having a problem with your car? I said one or the other, remove the negative or positive power from your battery, wait 15 minutes and try it again. Also check your throttle body and clean it.
Would this help with your theft system?
I found this; it may help with your issues :
Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time. The [COLOR=blue !important][COLOR=blue !important]instrument [COLOR=blue !important]panel[/COLOR][/COLOR][/COLOR] cluster (IPC). BCM and PCM must be in working order and the Passkey system repaired
1. Turn the key to ON and attempt to start the engine and release the key to the ON position.
2. The [COLOR=blue !important][COLOR=blue !important]SECURITY [COLOR=blue !important]light[/COLOR][/COLOR][/COLOR] will illuminate. Wait 10 minutes until it turns off.
3. Turn the key to OFF for 10 seconds.
4. Turn the key to ON and attempt to start the engine. If it starts and run, the system has reset. If it doesn’t start or run and release the key to the ON position and complete the rest of the steps.
5. The SECURITY light will illuminate. Wait 10 minutes until it [COLOR=blue !important][COLOR=blue !important]turns [COLOR=blue !important]off[/COLOR][/COLOR][/COLOR].
6. Turn the key to OFF and wait 10 seconds.
7. Turn the key to ON and attempt to start the engine and release the key to the ON position.
8. The SECURITY light will illuminate. Wait 10 minutes until it turns off.
9. Turn the key to OFF and wait 10 seconds.
10. Start the engine
Will this method help with my dash board goin on and off radio blanks off locks on door and windows doesn’t work on a 2015 Chevy Camaro ls
That sounds like a body control module, operating all that. Thanks
@@camaromodschannel is there something I can do on take to the shop
@@vickiechalmers3855 YES, You need to take to the shop. Unless you know someone who knows cars very well. thanks..
Thanks
Any idea why when I turn on heat to the lowest setting the blower sounds like it's on high and then it shuts off? Seat warmers also won't come on.
Based on your description, it seems like there could be a problem with the blower motor or the blower motor resistor 1. The blower motor is responsible for blowing air through the vents, while the blower motor resistor controls the speed of the blower motor. If either of these components is faulty, it can cause the blower to make loud noises and then shut off 1. what year model is your car.. thanks
www.fixdapp.com/blog/how-to-replace-blower-motor-resistor/
So my friend has a camaro... its randomly throwing a stabilitrak service light. It also will just randomly die while in drive. When he went to use his turn signal the vehicle locked it's doors. No turn signal came on. Just random electrical things. And it randomly happens so it's hard to get it looked at. No codes can be found. Unplugged both positive and negative cables to battery. Looked at the fuses they were fine. Sprayed the wheel sensors with air and the cold air intake with air. It just started a week ago. And his dad can't figure it out. Do you have any ideas?
Sounds like a ground problem, or check your battery is in good condition, correct voltage. Or a charging problem. Thanks
@@camaromodschannel what is a charging problem? O'Reilly checked his battery and said it was good.
The alternator not charging the correct voltage.
Check your wheel bearings any making noise. Stability track is tied to the wheel bearing. Hard to diagnose on the phone. Thanks
@@camaromodschannel yeah I get that. Just some other ideas are nice to have. Thank you so very much!
Do you have to take fuses out to disconnect the positive wire?
No, just one or the other. Thanks.
You have a email because it won’t let me send pics through UA-cam or how do I if it does
@@davidbailey6842 camaromodschannel@yahoo.com
@@camaromodschannel I sent you a couple emails with the pictures
How you doing bro I have a 2011 Chevy Camaro V6 my fuel injector went out I replaced all injectors spark plugs coils rail sensor all Upstream O2 sensors massive flow air sensor and still getting a rich idle code do I have to reset the computer the valves are not that dirty actually they're pretty clean thank you for your time
Do you have a tune on your car? Thanks
What error code are you getting on your scanner.
I'm getting a rich code at idle on bank 1 and 2
I'm getting a p21 88 code and a p2190 code
There's no tune in the car but we have went into the computer turned off the downstream O2 sensors for the cats and the cats have been deleted
If i cleared the check engine codes will that solve the check engine light on?
If a light came on, you need it scanned to see what the code was and see if you can fix it. Thanks
Not a code issue but I’ve been chasing a problem for awhile. Maybe you will have time to respond.
Right brake and blinker out
Left front blinker out.
All bulbs are good
Don’t seem to have power to the harness on the right rear that controls the brake and blinkers.
All running lights are good
You check your bulbs, fuses, blinkers relay? Yes, you can have so much time chasing wiring problems. Blinker switch?
@@camaromodschannel yes Ive checked everything but can’t find a true blinker relay
Got the same problem no blinker on passenger side. Replaced whole tail light assembly and still not working. Did you find the problem? Help!
Funny thing is it’s just my blinker. All other functions work. Inside the harness it’s a 10 pin bc it’s an RS. On the pin that worked the turn signal I used a test light and it’s NOT lighting up. I don’t know where to start
I forgot that I posted this. Anyway I took the car to the dealership and although I checked every existing fuse on this car, even in the trunk they found that an entire fuse had fell from the fuse box. It was completely missing!!!!! They never found it but put one in the empty slot and I was back in business
I have a 2015 Camaro Ls I crashed the got it fixed but the guy didn’t mount up my computer for the car. It fell and burned a few wires. I fixed the wires but car does not start. The key turns but the car is dead. Battery is good. Can’t find any fuses blown. Can I get some advice please
Sounds like you had a short and burned something up, you say its dead, and won't turn over? You need to get it to turn over before I would recommend getting another computer.
Same exact problem… did u figure out problem
@@redhillliard6787 The Dealership has to reset the computer
Good at least you found the problem. Thanks
Hey there I recently swapped engine 3.6 but when I turn the key it just clicks and got power to starter and battery but my radio and windows doesn't work just thought I asked thanks
Check all your grounds, thanks
Did it lost communication to the ecu? Cause I recently changed the engine for another v6 and every time I try to start it it does nothing but the moment I take out the key is clicks
My 2019 Ss got water in trunk wetting all the wires now my car giving all types code will not run took to dealer in they said I need to replace the body harness for $7000 the water damage the wires any help
Get another dealer, there's scammers out there. Get another estimate, and take it to a better shop. Thanks
I have my camaro set for when i open the door after shutting engine off, the dash lights turn off right away, (i dont need them on for 30sec or 1 min etc..) but now when i open the door to get out they stayed on even though in the settings i have it set to have the lights off right away, what could this be?
The body control module controls this system. Have you disconnect the battery for 15 minutes to try to reset it. Thanks
@@camaromodschannel I have not... I'll try it this weekend and let you know! Thank you!
My camaro throws code 2230 and 2227, i switched out the map sensor and still throws the code, now my car drives and starts reduceing power but gauge sais im going a higher speed
Looks like you need to change out the mass air flow sensor on your air intake tube. Or check your air filter is not really dirty. Thanks
Pulled the positive cable from the hood , key forward , still have power to the car lights , and door ajar going off
You will have to pull the positive post off the battery to make sure you have no power. I don't know how you still have power. Thanks.
I don't have an aux. Check engine light on in key on position. No communication to ecu. Any suggestions? thx
Check Your Battery, And Grounds.
2010 llt Camaro with a recently swapped 3.6 v6 only it came out of a Cadillac same block and heads it’ll crank once most of the sensors are connected but won’t start it throws codes only for TB p0698 p2119 p2176 p2101 please help!
Error Code P0698 is defined as Sensor Reference Voltage C Circuit Low,
What the P2119 code means. This code indicates that the throttle valve is not in the position the PCM (Powertrain Control Module) expects it to be in
What the P2176 code means. The P2176 trouble code indicates that the Engine Control Module (ECM) has detected that the throttle body actuator/motor has failed to learn the correct position at which the butterfly valve within the throttle body should be in order to produce a smooth idle for the engine.What Does the P2101 Code Mean? Diagnostic Trouble Code (DTC) P2101 stands for Throttle Actuator “A” Control Motor Circuit Range/Performance. It is usually triggered when your vehicle's powertrain control module (PCM) detects that the actual throttle position does not match the desired throttle position. also make sure you have a good battery. I would try swapping the throttle body, and see if that helps, or get the computer that goes with that engine.and try that. thanks.
@@camaromodschannel yes indeed I have checked most of the DTC’s that I can read with my obd2 scanner and recently today replaced the throttle body with a cleaned out one but the same 4 codes pop up still,so would this be for sure a computer replacement situation or could I still salvage the one already hooked up by resetting it?
@@ogdiablo6663 see if you can get a computer and try it. Did you get all sensor connected?
@@camaromodschannel yes most of the important sensors are plugged in beside the radiator and fans but will see if the computer is the issue to be sure
Appreciate your videos. Question...randomly getting check engine light, but OBD scanner often says "no codes". Yesterday while highway driving at 70 mph sudden misfire and a 0007 code...misfire went away...cleared code and car began running better than it has in months. Any ideas?
Looking like a fuel shutoff valve,
Does this help with anti theft lock my car locked up on me now won’t turn on
Can you get to the battery?
I recently bought a 2012 Camaro with a 3.6 V6. The check engine light came on and the door ajar warning came one and stayed on. The alarm quit working and the drivers window wouldn't roll up. I replaced the door locking actuator and everything went back to normal but the window. I replaced the switch and it worked for a few minutes and quit. Now I'm back at square one. When the check engine light was on I took it to AutoZone and they said the ECM was bad. What can I do to fix the problem I'm having??
What codes came up at auto zone? Body control module? Hard to say over the internet. Thanks
@@camaromodschannelAutozone told me it was the ECM but my friend hooked his scanner up to it and it said BCM. It had 13 codes
@@mikebertolis5829 yes that is what I was thinking. souns better tham a ECM Thanks
The BCM is the culprit. I'll be ordering a new/used one and I'll have it reflashed for my car
@@mikebertolis5829 Awesome Glad you found the problem, Thanks for letting me know. Thanks.
After the reset my engine light came on. Will it go off by itself after driving? It wasn’t on before the reset
It might, what code is it saying.
@@camaromodschannel plus communication to the transmission control module and also the body control module and also the engine control module and it through one for the can bus communication. I had codes for all my wheel speed sensors and I replace them today, but it was still seeing the codes and it also said incorrect immobilizer identifier received.
@@camaromodschannel but when I reset the Tcm buy starting it up and shut it off and waiting. I did that five times, and the check engine light went off. I just did that like five minutes ago.
@@camaromodschannel but I do have a question about the antilock brake system. He gave me a secondary DTC and it says it lost communication with the electronic brake control module. Now is that the part that’s under the hood on the left-hand side with the four lines running to it
@@davidbailey6842 can you send me a picture of it so im sure of what I'm telling you. Thanks
I got a service theft deterrent system msg and my car turn off randomly when I’m driving and not just that I have to disconnect my battery every time it happens got any advice
Check your grounds wires. You have a short somewhere. Thanks
Did you find the issue my 2017 ss is doing this
My camaro has been throwing stabilitrak lights and idles bad when warmed up changed spark plugs and coils still sounds terrible
I have see that problem before, check your throttle body. Clean or replace, if you have a tb you could try out from another car so you can know that's the problem. Thanks
Is car on or off while using the positive method
Off, thanks
Does this help with the stereo problems
Yes, it could if your radio is acting weird. Thanks
2016 Camaro ss starts an idles for 5/10 seconds then says anti-theft then dies. Have & programmed new key starts the car up but doesn’t unlock doors. All keys lost.
ua-cam.com/video/6JILUy02FIA/v-deo.html see if this video will help, Thanks..
Do u know the best way to fix a backup camera problem ?
You having trouble with the camera or the monitor?
@@camaromodschannel Chevy Camaro 2011 backup camera
I replaced my window regulator in a 2015 camero and it still does not work already try re cabrating and even returned window regulator and got another new one same thing don't work ? Help!
That would be in your body control module, needs replaced, or reprogrammed. BCM Thanks
Thanks bro!!!
Thanks
@@camaromodschannel questions any problems with volo tuner? You still use the volo vp16?
So what if I replaced the throttle body with new sensor and pedal position sensor and also replaced 02 sensors and did the reset and cleared the codes with handheld scanner and still get the same codes???
Is there a relay or fuse for either pedal or throttle body?
Also does the key need to be in and on for this process?
No.
Yes
You still have a problem somewhere.
5th gen camaro, new starter and new battery, added grounds. Hot start issue which throws the stabilitrack codes. After cooling off it starts fine. Been happening for years. 😅. I really do wish I could find the fix.
What codes you getting? The throttle body likes to throw them codes. Something you could try if you have one you could borrow.
Crankshaft and camshaft position P0341 and P0335. Only when hot. Im wondering if it's low voltage in the wiring due to the heat?
@@corrosivepyro those problems are somtimes so hard ti figure out. hope you can, thanks
Yeah, I nearly gave up on it. I'll just continue to modify it and maybe it will eventually go away. I think it's wiring related.
5th gen TT 715whp
@@corrosivepyro Nice Build. Thanks
I will try this because my check engine light is on . The code said oil pressure sensor. I change it out had the mechanic clear the code out and drove it for about a week and now the dam check engine light is back on. I checked the oil it’s good Now I am at a lost to what it could be now. I had AutoZone put it on the code reader and it said engine oil pressure sensor range/ performance. I went and bought another new oil pressure sensor because I was thinking maybe the one I bought was bad also. So any way if this has happen to anyone or if anyone can help me I would be thankful. My care is a 2014 SS Camaro.
Buy OEM, I hear the aftermarket parts are junk. Nice car.. thanks
@@camaromodschannel Thank you 🙏
Having same exact issue did you figure it out because im at a loss here trying to figure it out@adriandunham6425
Replaced computer, programmed ecm but key won’t start car. Battery is good and the theft light came on. How can I bypass it?
Put your key in the door and turn and hold for a few seconds let's the computer know that you are the owner.
@@camaromodschannel tried to do that and still won’t turn on. Battery is good. And I tried the method of reprogramming the key. ON position for 10 mins and off 3 times repeated but no luck
I have 2015 low miles 80,000 when I’m going 40 or going up hills it surges . Like it misfiring. No check engines lights or anything
Wow those are hard to figure out sometimes. Have you cleaned the throttle body in a while, may not fix it but just another thing that's not a problem. Those things cause so many problems but they throw codes also. Thanks
I was thinking about buying a new throttle body. I wouldn’t have to reprogram my car do I?
No not at all..@@flippycupflip
Thank you
My 2013 v6 I get stabilitrak and then it misfires on cylinder 1. Runs rough. Also, sitting in park while it is running rough I put the accelerator to the floor to see if it would rev and it revs up and down on its own with peddle all the way down. What is wrong with this sob?
I would check your throttle body, and coil pack on cylinder 1,
@@camaromodschannel okay I cleaned throttle body thoroughly. I’ll check the coil
My car cranks but doesn’t start my fuel pump and high pressure fuel pump working switched out my crankshaft position sensor as well and still don’t turn on , got all these codes ,P062b,u0100,p025A,p0107 what should I do now ?
I did switch out my high pressure fuel pump along with the crankshaft sensor
You have a problem with your fuel pump. Or like a ECM problem. Thanks check your fuel pump.
@@camaromodschannel my fuel pump still clicks and gets 60 psi from just that pump, what can I do if it’s the ecm?
See if you can borrow one to make sure that's the problem. Before you buy one. Thanks.
@@camaromodschannel borrow a fuel pump or ecm? And sorry for bugging just been struggling so much to get this thing running
Just say remove number five and number 20 fuse for 15 minutes to a half hour resets the computer in case you get bad gas and put it back to 91 tune if we pull out five and 20 fuse resets it back to 93 tune if that’s what you have
Great advice, thanks
Hi sir I have comaro 5th generation my car stop parking but the gear is R and gear shifter is stuck now please help me
Sounds like something broke, not sure. Make sure your car is on level ground. Might be a micro switch in the shifter stoped working. Have you had trouble with your shifter before?
@@camaromodschannel no sir I don't have any issue just I stop car and it will happen. But really sir thanks for replying me 🙏😘
@@abuhassanhassan6233 you may have some one lookAt it and see what you need to fix it. Thanks.
My Camaro 2018 is stuck in theft deterrent mode, please helpp
Put you key in the door and unlock it and hold for 4 seconds. See if that works. Thanks
Reverse gear is in parking mode and shifter is stuck I released shifter but not working gear system
I will look into this problem. Thanks
What do I do if it say service Stablitrack and it says service parking assist
That is your sensors in your back bumper when you get close to something it will sound. I would just check and see if it's still working. May have a sensor you need to replace. You can get them from ebay or your local Chevrolet dealer. Thanks.
@@camaromodschannel even though it says service stability track and parking assist when it happened everything in the dash went to zero I don't know I think it may be a body control module how do you reset one or do I have to buy a brand new one
You may need to take it into the shop, or you can get another body control module. And see if that will work. Thanks.
@@camaromodschannel it's already at Petty's garage that built the car but the guy up there is having a hard time figuring this BS out lol
@@camaromodschannel and thanks again
Will this calibrate a new maf sensor too?
No the computer will have to do that after you reboot your computer in your car. Thanks
My car isn’t throwing any codes but it’s stuttering and is having issues with staying in gear
Automatic? Low on fluid? Thanks
Does it work if the radio display says locked
No, that is an antithef system, you will have to go to the Chevrolet dealer to have the radio unlocked.
What if i have a push to start? Theresnot necessarily way to keep it in the on position
What car you have? Make model year?
@@camaromodschannel
2017 camaro. The 2.0 turbo
Manual
Press the start button without touching the brake will power your car without starting it. Thanks
How do you reset your anti thief deterrent
What car? Camaro?
2021 zl1
Camaro
Insert the key in the door lock all the way and then turn the key to unlock your car door, but don’t release it. You want to hold the key in the unlock position for twenty to thirty seconds. This lets the car recognize that you have the right key and will disengage and reset the system.
@@camaromodschannel this also works on a 2013 Camaro ?
Ok i am getting a "reduced engine power message" But have zero engine lights, zero codes and the car has full power and runs great. i just get that message pop up every 2mins and it is very annoying Plz help me someone!!
Check your air filter, fuel injectors, fuel pump pressure, oxygen sensor,
@@camaromodschannel ok i also put it a the dyno and ever since then i started i checked with scanner and seen EBS Eletronic Brake system communication error. i tried resetting the abs system the whole computer system and nothing?
No crank no start 5th gen Camaro replaced battery and the alternator pls help nothing I try works
Have you checked your starter? what year of Camaro?
@@camaromodschannel 2010 rs camaro v6 , I haven’t checked started I tried starting it with a dead battery n I could hear the starter but it’s jus dead silent I was thinking ecm but idk man shits a headache n was jus trying to get pointed in the right direction anything at this point helps , thank you !!!
@@camaromodschannel I added a ground wire from the chassis to the motor jus incase there was a bad ground
with a 2010 I would check the starter befor the ECM, starters and batterys go out. Thanks..@@exerain5095
@@camaromodschannel I will try that and hopefully it fixes it I’m jus not sure cuz last night it cranked for like a second then stopped cuz the battery was dying but I charged it today and nothing no crank or nothing
Miles ?
No it will never reset your mileage. Thanks.
Captain Kangaroo
Well yes.. lol
I have a Camaro and I am having issues with my car
It cuts off while sitting still and when I drive it reduces power and go really slow and it want go up a hill
What codes you getting? First thing I would check is the throttle body, get some throttle body cleaner and clean it good.
Let me know if that works. If not we will come up with something else. Thanks
I changed my battery and it still doesn't start
Do you have any computer codes? Check for fuel, spark. Thanks.
I reset and check engine light came back on 5 minutes later
You have a problem, what code you have?
Iike pulling teeth!!
Yes, pulling fuses?
Snooze!!🤤
?
Just to let you know i txted you on email
Ok.thanks