PROGRAMMING INSTRUCTIONS: When you purchase the unit, you have to take the time to read them and understand the pattern of logic for the keypad entries. Here's a clue (0000 is the user code, as this is the factory default when you first get the lock): Think of the "Kwikset" button as "ENTER". I will call it that from here on. Think of the PC (programming code) as a "key" to let you into the “Control Room” where only you can access the functions. Every time you want to do something other than unlocking the door, you need to use your "key" to be able to do it. When you enter the "key" (by default, pressing 0000 ENTER), you've entered the "control room". Each of the ten special functions has a number. There are ten buttons on the keypad and each on has a special function. These functions are: 0 - RESTORE DEFAULT ORIGINAL FACTORY SETTINGS (only AFTER you have hit the "reset" button.*) 1 - ADD A USER CODE 2 - DELETE A USER CODE 3 - DELETE ALL USER CODES 4 - CHANGE YOUR PROGRAMMING CODE 5 - ENABLE/DISABLE AUTO-LOCK** 6 - CHANGE AUTOLOCK TIME DELAY 7 - MUTE/UNMUTE LOCK** 8 - ENABLE/DISABLE ALL OF THE USER CODES** 9 - ADD A "ONE TIME ONLY" USER CODE Now, pay attention to the pattern of keypad commands. The pattern is: 0000 + ENTER + [ special function number ] + ENTER This is the pattern to engage any of the ten special functions (see list above). If the function involves a number (user code), then you add + [the number] + ENTER after the pattern above * Resetting to factory/default settings begins with pressing the tiny reset button, which is on the inside/back of the lock, underneath the removable cover that you just lift up and lean toward you to release. It's in a little hole, so you'll need a ballpoint pen, un-bent paperclip, or some other small thing that can fit into the tiny hole. When you first press it, there is a beep. DON'T RELEASE IT, keep pressing and wait . . . quite a long time . . . until you hear THREE beeps. Then it's reset. ** All of these "enable/disable" functions can be tricky, because it's not very clear if you have enabled or disabled when you key in the sequence. I noticed that the ENTER button illuminates green for enabled and red for disabled.
Hi Geri - Thanks for your feedback! Here's a link to the installation guide. After performing the reset, complete the handing process in step # 6 before moving on to the programming instructions in step # 8. Within section 8, we recommend following steps A, B, and C in sequential order. kwik.st/3lLIfED Thanks ~ Kwikset Social
The rubber buttons really feel mushy and soft, you feally have to push the buttons firmly to engage. Wish the buttons were made more solid.. With the heavy traffic at my house, these buttons will wear out in no time
Hi! Our Consumer Support Team is here to help... please contact them here: kwik.st/3CTk8xl or call them at 1-800-327-LOCK (5625). Thanks ~ Kwikset Social
MeganIs Magical very bad and unclear instructions ... mine only works with the key in it... no way to make it work without it and no way to troubleshoot ... been reading reviews and you have a very bad product
Bought a new one, followed the steps but deadlock doesn’t close by itself, after accepting the new code still blink the red light 3 times I used the 0000 changed it for a new one and set a new code, still not working, any tips? Or maybe is malfunctioning on mine?
Hi Junior - happy to help you with this. To ensure the user code programs are successful, please make sure to check the installation in step # 5 and follow step # 6 in the installation guide. Follow steps A, B and C in sequential order within section 7. To enable and disable the Auto-Lock feature, see section 8. kwik.st/3o3oV8y For one-on-one troubleshooting help, please call our Support Team at 1-800-327-LOCK (5625). Thanks ~ Kwikset Social
Hi Patricia, This video does not contain programming instructions. Please give our team a call at 1-800-327-5625 for programming assistance. Thank you, Kwikset
PROGRAMMING INSTRUCTIONS:
When you purchase the unit, you have to take the time to read them and understand the pattern of logic for the keypad entries. Here's a clue (0000 is the user code, as this is the factory default when you first get the lock): Think of the "Kwikset" button as "ENTER". I will call it that from here on. Think of the PC (programming code) as a "key" to let you into the “Control Room” where only you can access the functions. Every time you want to do something other than unlocking the door, you need to use your "key" to be able to do it. When you enter the "key" (by default, pressing 0000 ENTER), you've entered the "control room". Each of the ten special functions has a number.
There are ten buttons on the keypad and each on has a special function. These functions are:
0 - RESTORE DEFAULT ORIGINAL FACTORY SETTINGS (only AFTER you have hit the "reset" button.*)
1 - ADD A USER CODE
2 - DELETE A USER CODE
3 - DELETE ALL USER CODES
4 - CHANGE YOUR PROGRAMMING CODE
5 - ENABLE/DISABLE AUTO-LOCK**
6 - CHANGE AUTOLOCK TIME DELAY
7 - MUTE/UNMUTE LOCK**
8 - ENABLE/DISABLE ALL OF THE USER CODES**
9 - ADD A "ONE TIME ONLY" USER CODE
Now, pay attention to the pattern of keypad commands. The pattern is: 0000 + ENTER + [ special function number ] + ENTER
This is the pattern to engage any of the ten special functions (see list above).
If the function involves a number (user code), then you add + [the number] + ENTER after the pattern above
* Resetting to factory/default settings begins with pressing the tiny reset button, which is on the inside/back of the lock, underneath the removable cover that you just lift up and lean toward you to release. It's in a little hole, so you'll need a ballpoint pen, un-bent paperclip, or some other small thing that can fit into the tiny hole. When you first press it, there is a beep. DON'T RELEASE IT, keep pressing and wait . . . quite a long time . . . until you hear THREE beeps. Then it's reset.
** All of these "enable/disable" functions can be tricky, because it's not very clear if you have enabled or disabled when you key in the sequence. I noticed that the ENTER button illuminates green for enabled and red for disabled.
Hi Geri - Thanks for your feedback! Here's a link to the installation guide. After performing the reset, complete the handing process in step # 6 before moving on to the programming instructions in step # 8. Within section 8, we recommend following steps A, B, and C in sequential order.
kwik.st/3lLIfED Thanks ~ Kwikset Social
I changed the programming code and it goes green when I enter it but the lock doesn't come out..
How do you program it???
Please see page 8 in these instructions, s7d5.scene7.com/is/content/BDHHI/66101-01
The rubber buttons really feel mushy and soft, you feally have to push the buttons firmly to engage. Wish the buttons were made more solid.. With the heavy traffic at my house, these buttons will wear out in no time
Hi! Our Consumer Support Team is here to help... please contact them here: kwik.st/3CTk8xl or call them at 1-800-327-LOCK (5625). Thanks ~ Kwikset Social
Can you re-key this lock?
Hi Joe,
This is a traditional pin and tumbler lock and can be rekeyed by a professional locksmith.
Thank you,
Kwikset
I am trying to program the 264 series kwikset electronic deadbolt. I can not do it. Anyone know?
Please see page 8 in these instructions, s7d5.scene7.com/is/content/BDHHI/66101-01
MeganIs Magical very bad and unclear instructions ... mine only works with the key in it... no way to make it work without it and no way to troubleshoot ... been reading reviews and you have a very bad product
Daniel Barberena wait I think this was my dad who commented..
Alguien puede decirme como cambiar el código de esta cerradura?
¡Hola! Nuestro equipo de atención al consumidor está aquí para ayudarlo ... contáctelos aquí: kwik.st/33FusYc o llámalos al: 1-800-327-LOCK (5625)
Bought a new one, followed the steps but deadlock doesn’t close by itself, after accepting the new code still blink the red light 3 times
I used the 0000 changed it for a new one and set a new code, still not working, any tips? Or maybe is malfunctioning on mine?
Hi Junior - happy to help you with this. To ensure the user code programs are successful, please make sure to check the installation in step # 5 and follow step # 6 in the installation guide. Follow steps A, B and C in sequential order within section 7. To enable and disable the Auto-Lock feature, see section 8.
kwik.st/3o3oV8y
For one-on-one troubleshooting help, please call our Support Team at 1-800-327-LOCK (5625). Thanks ~ Kwikset Social
why did you have us program the wrong code....now I have to delete (punch that little button) and recode??? WTF
Hi Patricia,
This video does not contain programming instructions. Please give our team a call at 1-800-327-5625 for programming assistance.
Thank you,
Kwikset