Pulling Out A Dent - Will The Dent Pop Out?
Вставка
- Опубліковано 18 лип 2018
- Watch to see if this dent will pop out using glue.
Hey, I’m Steven from www.exceldentremoval.com I’m going to use glue and a dent lifter to pull out this dent. You will see the process on how using the glue method can safely pull out a dent without having to use a body shop to fill it with bondo and repaint.
✅ Check out my customers 5 Star Review for this repair
⭐⭐⭐⭐⭐ goo.gl/maps/qkRvhEuA8vL2
My customer brought in his brand new 2018 Honda Accord to have me use paintless dent repair to take out this dent. Now he actually drove further than most would to have me do the repair because he wanted an excellent repair. He had already took the car to another dent guy near him and decided that his option was not the best for his car. He had wanted to drill an access point inside the door jamb in order to access the back of the dent. While this may have worked, though the area that was damaged does have limited access this way, it was not the best option for a brand new car.
************************************
See my list of recommended PDR Tools on Amazon
➡️ goo.gl/vVrHxQ
************************************
Tools Used in this dent removal:
➡️ Knock Down Tip from Edgy Tools - goo.gl/Vs4bnx
➡️ PDR Knock Down - goo.gl/7AK2N1
➡️ PDR Glue - goo.gl/EfH5QG
➡️ Glue Tabs from Edgy Tools - goo.gl/3drfS4
➡️ Other Tabs Used - goo.gl/oT4UdR
➡️ PDR Mini Lifter - goo.gl/bPPa5N
➡️ PDR Slide Hammer - goo.gl/5cZqR1
➡️ PDR Lights - goo.gl/jkgRmJ
(Some of these links above are affiliate links. You will not pay more when using the links above. These will take you right to the products for purchase. I then make a small commission for helping you to find them.)
************************************
This dent in the right rear quarter panel of the car was caused when my customers bike tire fell and hit the side leaving this 4-inch dent. My customer had his new car just a week when this happened and still had the dealer plates on the car and not even 1000 miles yet.
I started to remove this dent using glue and was able to get a major amount of the dent out, but it still wasn’t enough for our standards. Especially on a new car. It did still take several times using many different glue tabs to slowly pull out the small areas of the dent.
The other option was to use some PDR tools and with access inside the trunk be able to make small pushes to finish the dent. I did attempt this but the access was not good enough to do it properly.
Paintless Dent Removal is the best option to repair the dents in your new car. Some of the benefits compared to using a bodyshop are:
✳️ Cost Savings
✳️ Time Savings
✳️ Better Quality Repair
✳️ Excellent Results
✳️ Increased Car Value
✳️ Better For the Environment
Now you may have seen other video where they stick the glue tab on the car and just pop out the dent like it was magic. Well, that isn’t really how it works. When the metal on a car is dented it does not just pop out and it needs to be molded back into place.
When we use the glue tabs and PDR glue sticks we have to use just a small amount of glue and just certain glue tabs that will shape and conform to just the right spot on the dent. Doing this brings up the dent slowly and in such a precise way as do not cause further damage and get a smooth result.
✔️If you are looking for a Paintless Dent Repair service to remove the dent in your new car. Then you can contact me at the info below to schedule an appointment.
I look forward to providing an excellent PDR repair for you.
Excel Dent Removal
1550 91st Ave NE # 303
Blaine, MN 55449
Phone: (763) 780-4000
Excel Dent Removal Website:
www.exceldentremoval.com
============================
Subscribe:
goo.gl/ZVlsrz
UA-cam Channel:
goo.gl/EimW1A
Google+ Page:
goo.gl/8NA1ux
Facebook:
/ exceldentremoval
Twitter:
/ exceldentrepair
Excel Dent Removal Blog:
www.exceldentblog.com/
Linkedin Company Page:
/ excel-dent-removal
-------------------------------------------------
▶️ Check out these other Glue Pulling Dent Removal Videos: goo.gl/z584Jr
-------------------------------------------------
❌ How NOT TO Pop Out Dents in Your Car
lifehacker.com/5983992/remove...
www.wikihow.com/Remove-a-Dent...
diy-auto-repair.wonderhowto.c...
-----------------
#paintlessdentrepair
#gluepulldent
#denttools
=============================
Watch this video Here: • Pulling Out A Dent - W...
=============================
Pulling Out A Dent - Will The Dent Pop Out? - Авто та транспорт
Most dents are not a quick pop out dent. If you have questions about using *Paintless Dent Repair* to take out dents in a car, then leave them in the comments below.
You are PRO sir. That level of attention to detail and patience . Amazing job!
Thank You! Yes, it did take some patience to be able to pull this dent out.
Will the glue method you had used on that Honda work on dings that have a Paint Protection Film (PPF) on the body panel? My car has a ding at the same location (rear right quarter panel) but that panel has a PPF on it. Thanks for any insight sir.
No it will not work. It will either tear or pull off the film.
You can see an example in this video here. ua-cam.com/video/cJjQZJ9feV8/v-deo.html
where are you located
People don't realize how much skill and time is involved for these.
Yes, you are correct. Paintless Dent Repair is not the "quick fix" that people see online. For quality results, it takes lots of time and skill.
Thanks for Subscribing 👍
wooow this is next level art
Did so diligently. Nice effort
Great work! I hope to have someone like you in my country...I have the same problem the the side and edge of my door..the dent professional says that they can't help much as they can't twitch from the door panel, inside out. But looking how you glue pull it, it's actually possible. It's required efforts and diligent hands like you.
Class video.. Excellent work.. It's the first of yours I have seen, love the time-lapse.. Bit of music but mostly the honesty in total repair process! Nice work 👍💯
Thanks!
Really great work and you seem like such a nice genuine person. Well done 👍🏼😁
Thanks! I appreciate the awesome comment.
Excellent glue pull repair on that car
Simply a fantastic video on the glue pulling method. No they don’t just pop out. Very well done Excel Dent!
👊 Thanks!!
Wish you lived near me I have a little dent in same place and everyone wants to drill and respray. My car's not done a thousand miles yet. Amazing work you did with no access. You are an artist
Thanks! There should be a quality company near you that could repair your dent.
My dent repairs are %10 better now after watching your videos
appreciate it!
Nice explain for the customers. Nice work :)
Thanks!
You are a genius,I would pay you money to train me! Amazing result, great video, thank you!
Thanks!!
Very nice repair on a very difficult dent! Had a similar dent on Monday and had a nice pile of of glue circles on the ground until that edge pulled..lol
Thanks!! Yep it was a little more difficult than I thought it would be. But it turned out great.
It sure did!
Great job and good viseo showing what happens
Thank You!!
One of the better videos good job
Thank you!! Be sure to check out some of my other videos that show different PDR techniques being used.
Nice job Steven, always an awkward place to get behind, looks like the glue pulling was kind to you and got most of it out before going in with the rods!
Thanks! Yes. I thought I’d have better access with a PDR tool from the trunk without having to remove the tail light. But the best I could reach it with was a whale tail tool and it was just spinning around.
I ended up just spending the extra time Glue pulling all of it.
Good work on a really tough dent position. It looked 100% better
Thank You! Definitely was a bad place for the dent, but the results did turn out excellent.
Brilliant job!
I appreciate the comment. Thanks!
Awesome video Steven!!
Thanks Brice!!
Flawless work 👏🏻👏🏻
Thank you so much 😀
Cracking Job 👏👏👏👏
Thanks for the help- I'm doing body work on a car that will get a new paint job down the
road, so besides using a dolly and a hammer I wanted to try glue pulling.
I happen to watch a guy who puts clear shipping tape over the dent so he would not pull
any of the original paint while pulling out the dent.
One thing I did not tell you was I have been trying to pull the dent out on bare metal and
I get no where, so I tried the clear tape over the dent & bare metal and it worked.
I guess the glue needs something like paint to create a good bond and the tape does
the trick.
Thanks for your help
Yes, the glue does need to be able to stick. Great idea using the packaging tape.
Good work😊😊😊
Bad ass work man. Exelent video👌
👍
Nice work 👍
Thank You!!
Pro work!
👍 Thanks!!
Nice job
Thanks!
I like how you explained all your struggles. It's not just me having these same difficulties! Volcano issue. tabs not small enough to pull small dent with no access or the ones that are small enough don't have enough surface area to produce the pull power required.
Any luck with better tabs or pulls??
It really needs to start at good pull first on that edge and bit of dolling the inner door to reduce pressure then continue glue pulling that.. its a very challenging job.. great job..
Thank You!! Yes, that edge did require some work. I probably could have started with that and it may have made it a little easier.
This dude got skills 👍
Appreciate it!
Hi, i have a renault grand coupe, i have the same exact dent, same spot also.
They thing is, i have those amazon tools and i do have a little scratch of paint at the center of the dent.
Is it gonna work by pulling? Or should i take off the tail light and buy more tools ?
Will check out links in description 👌
Nice work! Tough location right on that dogleg. Thanks for sharing the techniques which worked for you. Way to hang in there!
Thanks for watching!!
Ohh my idol... I'm from Philippine's
If i have dents on the inside of my door pillar would it be better to pull the dent this method but they are very sharp little dents (seatbelt buckle got slammed by passenger when they were closing the door) or just have them bondo... I'm planning on spraying over the car.
If the dents are sharp then glue pulling probably won’t help with those dents.
I’ve repaired those type of dents before. It usually requires removing the inner door panel for access behind the dents to push them out.
Nice job that requires lots of patience. Would you say you spent good 3 hours on it ?
Yes. I believe it was about 3 hours just repairing the dent.
Probably was around 5-6 hours with filming and clean up.
I have a similar type of that but not on edges nut on a lower part of the door of vW Passat whose metal is flexible on that are . Any suggestion ?
+Haard Dwivedi Glue pulling may also work for your dent. If there is open access I would usually try to get behind the dent and use PDR tools to push out the dent. Dents in the lower part of the door offer require removing the inner door trim for access.
Sometimes both methods of glue pulling and pushing from the inside are used.
Awesome job! How much does it cost?
+TC Vlogs The average cost for paintless dent removal can usuallly start at $100, then $25-$100 is add per inch in size. This is based on many factors including the location of the damage and the difficulty factors to repair it.
The dent in this video would average around $250-$400.
Dear Professional,
What brand of glue you use? I am in Australia and all glue gun sticks I used do not hold on the car body.
Thanks for advice.
L.
It could be because of the heat where you are at. If it is not holding to the panel, this could be because it needs time to cool or use something to cool the panel before and after applying the glue.
There are also some PDR Glue that is better designed for hot and humid weather.
I have some that I use listed on my Amazon shop here ➡️ www.amazon.com/shop/crownedcompanies?ref=exp_loc_sh_crownedcompanies
You can also look at the selection of glue from Anson PDR.
Look at that dent guy gloving up while using alcohol. Smart choice. I've been telling techs to do that for years. Great job.
Thanks! Usually for a small couple of glue pulls I won’t use gloves. But for longer periods I have to. Especially being in Minnesota in the cold dry winters. My hands would be raw.
Excel Dent Removal I read that denatured alcohol is carcinogenic, damages kidneys and causes problems in the central nervous system. It absorbs easily though skin. The stuff isn't good. Been unsing 91 percent isopropyl now with gloves. Used denatured for 10 years without gloves. I'm an iowa guy and work in Minnesota a lot. R u in the cities?
Yep. Stopped using denatured a long time ago and switched to 91%.
Yes I am north of the cities in Blaine.
So, if it’s a small faint dent on a body line, is it best to leave it alone?
Many types of small dents can still be repaired, including if they are in a body line. It would be better if there is access behind the panel to push out the dent, but it still could be possible with glue pulling.
This same BS just happened to me few minutes ago.
Brand new Acura ILX, less that a week of me owning the car, 600 miles only and just got smacked by a freaking shopping cart at home depot... The wind was extreme and out of all the cars there, the shopping cart had to chose mine. The dent is deep and it scratched the paint real good
very good, pity you rushed a bit but of course that would have produced a giant vid
I will usually run a time lapse of the repairs since they can take several hours. It is such a slow process. It’s almost like watching paint dry.
This repair took around 3 hours.
Did it leave some mark in the paint?
The damage was caused by a rubber bike tire that hit the panel. So it only left some minor transfer. I was able to buff the mark off with no damage to the paint.
How did you shrink the metal
There was no shrinking involved in this repair. Just used the glue pulling to bring up the metal and then knocking down to smooth it out.
What tabs do u use most.
Thanks for the question. While I have built up quite a few hundreds of $$$ in tabs over the years, probably the ones I've been using most lately are from KECO. They have developed some great glue tabs for a variety of repairs.
I have some of their tabs linked in my Amazon Shop ➡️ www.amazon.com/shop/crownedcompanies?listId=383RG24403J0A
My brother got mad and threw his phone at his 2015 Acura tlx and there’s a dent beside where the gas thing is how could we take out the dent?
There are a couple ways I’d look at it to see what the best repair method would be.
If I could get access behind the panel thru the truck area or behind the fuel door, then I’d do that using regular PDR tools to push out the dent.
If no access, then glue pulling it out would be the way to go.
Well done. That area is really nasty to do.
Thanks! Yes it is a difficult spot to do, especially with only glue pulling.
I thought I would have better access for PDR tools but the access I had wasn’t enough unless I would have taken out the tail light, which would have required removing the bumper. I figured I could finish it with just pulling out the dent instead of having to take all the extra apart, which would have increased the cost to do the repair.
Excel Dent Removal I would of done it exactly the same but we'll done.. Impressive.
Does the glue leave a residual mess on the paint ?
No. This type of hot glue is designed for this process and for car paint. If the glue still sticks to the car or the tab, we then use a rubbing alcohol solution to easily remove it.
You can see it here in this video. ➡️ ua-cam.com/video/uPNP4GfDb1I/v-deo.html
Did you use heat for this repair?
No. I don’t think I did. The regular temp was warm enough and any extra heat would have made it take longer for the glue to cool or it may not have stuck at all.
What kind of glue do I use
There are a few kinds of hot glue designed for PDR use. The kind you use can depend on the damage that needs to be pulled and sometimes the outside temp and humidity.
Here are a few PDR hot glue that I use that are listed on my Amazon Shop. www.amazon.com/shop/crownedcompanies
Obviously when buying a new car - after some time there WILL come dents and scratchs. But it´s really a bummer to have a dent like this on such a new car.
Nice job, how much time was spent in it?
Hi. Thank you! I don’t remember exactly how much time I spent just pulling out this dent. Probably some added time added for filming.
I would guess around 3 hours working the dent.
What glue did u use?
Tab Weld PDR Glue. Link is in the description.
Check the “other tabs used” link. It’s at that site. Other link seems to be not working at the moment. I’ll have to update it.
Link fixed. 👍
Wowwwww
Thanks for watching!!
What glue need to use just a rehular glue gun?
+Jimbo Obrense We usually use special glue designed for dent removal on cars. These glues are less likely to damage the paint. There are different kinds for different temps.
There are several glue guns that can be used. Sometimes a regular one can be used but it will depend on the temp that it uses.
You can find a few of the tools I use and recommend at this link.
goo.gl/vVrHxQ
@@exceldentremoval thankyou so much mate!!! I cant sleep and worried on a small dent... but if i will you a regular glue gun what temp would you suggest???
I’m not sure exactly the temp that they use but the ones I have are 60 watts.
This is the worst place do repair.... incredible result glue pulling only. Congratulations!!!
Yep. The “dog leg” area of the car usually has no access and are often a deep sharp dent. Glue pulling is often the only way to get these out if possible.
@@exceldentremoval what kind of glue do I use
I'm impressed with the job you done but you had the camera a little too far away to see what you were doing.
Thanks for watching!! Some dents can be difficult to also see properly to repair while also filming it. In order to see exactly what I see while working would put the camera in the way for me to see to do a proper repair.
So if it’s such a small dent, but it’s difficult to work with and you spend the whole day working on it. Then of course you have to charge the costumer for the whole day of work. What if the costumer’s get angry when you charge him few hundred for such a small dent?
Since I've been at this for a while, I usually can know before I start working on the car how long the dent will take to repair. I then will provide an estimate before I start the repairs.
For this damage, it did take longer than expected since I wasn't able to use a PDR tool to work on it. But I still kept the cost the same as the estimate and did not charge more.
Excel Dent Removal how do you know how much you have to charge? How do you know how many orders will you be able to do in one day? How do the costumer book a place in your shop?
For example you have 4-5 cars you have to do, but it took you longer than expected, so you only finished 2 cars. What happens then? Will you charge these two more? You obviously wont work for peanuts. What will you do with the rest of the costumers?
The paintless dent repair cost is based on the size of the damage and the additional factors that effect the repair. We have software that will calculate the estimate for us based on this.
I have repaired thousands of cars and hundreds of thousands of dents over the last 20+ years' so I usually have a good idea on how long a repair will take. If it takes longer, it’s not usually more than 30 minutes to an hour. Since that can happen, I will usually schedule enough time for each repair or to give a “buffer” between repairs. This is also to give myself time to recover from the work. Especially if it is a difficult and labor intensive repair.
For scheduling repairs at my shop. I will take on the bigger jobs and have the car dropped off for the day or sometimes 2 days. For hail repair it can be for 3-5 days. This gives enough time for these larger jobs and also allows to have the smaller door ding repairs done while people wait. (Usually only 30 minutes to 2 hours) or they also leave the car for a few hours.
Excel Dent Removal thanks!
A bicycle tire fell on it. WTH? What kind of rubber tire makes a de t like that?
It was his girlfriend's purse. He couldn't tell his wife the truth and told you the same story.
Yep. It was a bike. He was a professional and even brought his bike with him to ride home when he dropped off the car for the day.
???&????? Ta pronto !!!
I have a problem with the glue i'm using, it seems to let go before any pulling happens.
is there any info on the web that explains the different glue colors and which holds the
best without letting go. The glue came with the kit, which was made in china.
any good glue products that is made in america that you would recommend
and do the colors of the glue have anything to do with the strength of the glue ?
Thanks
Here are a few PDR glues I use and recommend. They are listed in my amazon shop
www.amazon.com/shop/crownedcompanies
There could be a few reasons why the glue isn’t holding or the dent is not coming out.
They can be ambient temps being to cold or to hot. Average panel temp should be around 70-80 degrees.
Could be proper panel prep. Surface should be clean and free of wax. Also if there is a ceramic coating on the car, the glue won’t stick.
Other thing could just be that the dent is to sharp or not possible to repair with glue pulling.
You must have some crap bodyshops over there if after the repair it diminishes the cost of the car.
Also any panelbeater worth their salt could metal file a small repair like that without using a filler.
Pdr is great but please stop bitching about bodyshops.
Yes, you are correct. There are some body shops that do excellent work. I regularly send people over to a few select shops that need paint work done since these shops are the best at what they do.
These shops and many of the car body repairers will have me fix the dents because they don't what to have to paint the car. Especially when it is their own car. 🙂
This is because having to paint a car does reduce the car value when there is no factory finish. Many people don't know how bad the damage originally was since many panels have to be painted. This will reduce the trade in value or resale. Not something that is wanted on a brand new car. (My customer specified he did not want any noticeable repairs on his new car)
Again, there are still some excellent body shops that can do great work.