Hydraulic manual pipe bender #shorts ~-~~-~~~-~~-~ Please watch: "How to make a simple power bank without circuit - Homemade" • How to make a simple p... ~-~~-~~~-~~-~
No it’s not working. The bolts are bending. It needs a frame to support both sides of the upper rollers. Should be able to kink’r real good in the middle after that.
Legend has it that till this day he is pumping to get to 90° bend he always wanted
Work with what you have
So, about the bending part?
😂
Exactly!🤣
Looks like a pipe straightener.
🤣🤣🤣
This video was exhilarating
100 years later...
S....s...🤣
😅😅
Its bends finally
Where was the pipe bender? Over on the table behind the jack?
Those rollers are gonna snap off.
My friend also used to post half the videos like this, now oh God it is with me.
How did this video get all them likes when it was a failure????
When he say 150 an hr he means 150 an hr 😂
At least it’s not too slow
Show us the big dent/kink in the pipe
Worth the wait!
What is really bending is the rollers bolts
Very helpful the only thing is i can't find this type of bearings
Should be called a bolt bender
A steel pipe bender that no bend. 😮😮😮
Fail, the top bracket bent upward
You shoud tight the screw aside the hydraulic jack before you operating it 😂😂😂
😂😂
Não apertou o parafuso do macaco-prego para dar pressão 😂
Da Bedarf es noch etwas Modifikation 😉 ich will auch einen bauen 😉 aber bissel anders
Complete lack of common sense.
Jika btuh mesin bending pipa custome di infonesia slkan hub kami
Very nice
How to buy this
The only thing I see making bends are those fingers, did you manage to bend anything else? 🤣
Nothing bent here
El gato no sirve no le da presión
Perfect
faynal
Paid by hour
Can you help me get this bearings
Sang lugar po yan asap
....24 hours later....😅
so dangerous.
Not even a lil bit
Y el momento en el que dobla el tubo?? 😂
the bend is not shown because the screw has already been cut😂
😂😂😂👍
😂😂
In what life was something going to happen
Band karkay dikhao pipe . Tusi jo uper wali puli vich nut bolt lagay nay oh band ho jan gay ja tut jaan gay. Tuhada jugaad fail hai
Mr. George...
Скорее всего ничего не вышло.
Ano q bah!? abno Bomba q ng Bomba ai di parin bumabuloktot 😀😂🤣
he did this on purpose, lol
GAGAAAAAAAL
No le creó, ese truco 😢 está dudoso?..
Pipe lift it is
Yeah… good luck
Praise the lord
If this is as fast as this thing works then I give up allready. Woo
Dam waste of time here that is one hell of a disaster just waiting to happen under pressure. Start again 🤪
???😢
BRUH
Super little angle bending
Sry sir.... V r developing... Thanks
Prank
Wtf
Ain't doing crap
🫤
Umuwe kn magtanim ka ng kamote. .un kusang nag bebend.
Isso ai ê uma porcaria de enventamento
😢फालतू वीडियो
Cnot good not working
Poor engineering.
Just trying.. that's all.....
Non piega nulla🤣
I rectified sir...🤣
@@mrideaman1462 👍
Waste of my time
Psssssssss....
Is it not working..?
Working conditions...
No it’s not working. The bolts are bending. It needs a frame to support both sides of the upper rollers. Should be able to kink’r real good in the middle after that.
hahahaha
😂😂😂😂😂👎
Mal
14 hours later, get an air over hydraulic pump tf.
Pipe kinker not a bender