I make this sort of thing but I make sure the pry bar swings up and down for leverage. Plus there should be absolutely zero wobble, jiggle, so that all your kinetic energy goes into the bend. Also I use a really Stout long pry bar lever, makes it a cinch no struggle. Especially when you have to do hundreds and thousands of bends,💥 that's my two cents. Great job by the way. The next one I'm building, bends to solid bars at once.
Domaca pamet kad proradi iz radionice drago mi je kad vidim da neko radi sa apetitom vidi se da si perfekcionista nista ne prepustis slucaju.👍 Pozdrav iz Srbije
Very good. Then thinking of adding a big bottle jack with corded drill instead of a lever. Wanting to build my own exhaust system. Again thanks for posting.
Nice build. Only concern I have is the welded center pivot. The plating on those commercial bolts makes welding them sketchy. Make the center pivot 5mm longer and pass it through the baseplate, then weld the head from the other side. That will send the bending forces through the shank of the bolt into the baseplate, instead of through the welds on the sides of the bolt head.
I wasn't going to say anything, but with 7 million views, you have some responsibility to the people to be honest and point out that this does not work well and that it is far from idea. You are going to motivate people to purchase dies and materials to make this tool, and it will be a waste. I can see from the video that the bends are not consistent (the radius is changing) and the bends are damaging the pipe, unlike a properly built bender. This was a fail, and should have been labeled as such... or at least pointed out that this was NOT idea and the results were not great. Instead you hyped it up like it all went to plan. People. If you are going to bend different size pipe, you should be using the appropriate size die and follower. If you are going to bend more than one size of pipe with one bender, you need to have an adjustable follower or keep your follower close to the die to avoid kinking and other issues. This would be a good video IF it didn't end giving the audience the idea that you can repeat this process and be happy with the results.
Excelente forma de trabajar voy a ordenado muy ordenado muy limpio tienes muy buena herramientas todo excelente lo único que faltó fue una base de cemento en el patio para colocar la curvadora saludos desde Colombia
Queria eu ter a metade das ferramentas que ele utilizou. Mas é inegável a habilidade do rapaz. Ficou muito bom o trabalho. Parabéns!!! Congratulations!!
The video was quite cinematic as if someone had written the screenplay. Didn't skip a second like I do with most videos. A very interesting and informative one. Keep it up bro. GBU
Trebas ga malo preraditi,jer ovako mozes savijati cevi samo do odredjenog precnika(fi). Jedan roler si trebao napraviti da se moze štelovati pa tako da mozes savijati i deblje cevi. Inace korisna stvar. Pozz iz Srbije 👋
I made something like that for .500 tubing. Many years ago. I use a bearing on the small wheel. I Mande the wheels. I used a .500 wide tool bit. With the radius on it. Great job. Keep up your great work.
It looks like it's made for 1 size of Pipe only.The rear anchoring back U shaped plate should have been made to accomodate several different sizes. Otherwise I like how it has degree markings capabilities.
Wow awesome build thks for shari ya dont need to be rocket scientist to do this great idea going to build oe great for building gocarts and Old School Choppers so from Canada 🇨🇦 SK later 😊ya got this 👍
Zanimljiv video, odlična savijačica. S istom možeš si praviti vilice od rebrastog (šipki) željeza za armirani beton kod nadvoja, zidova, temelja i slično. Bravo Doctor. Veliki pozdrav!
you prolly dont give a damn but does someone know of a tool to get back into an instagram account..? I stupidly lost the password. I would love any tricks you can offer me
good idea, the only bad thing is the axis of the main mold welded to the plate and of greater diameter, the best would be past and thicker, it is observed how it moves by the applied force.
Hello Doctor D S. I'm Jessie from Philippines. Nice work and video. Will try to make this. Useful for the beginners in DIY things. Thank you for the informative video. Great Job sir! 🙂👍
Amigo buen trabajo gracias por subirlo 1)la chapa de 6 mm es fina de 1/2 para arriba 2)los tornillos no sirven ejes de 40mm para arriba 3) perfora la chapa de 1/2 la que pongas de base los clavas y solas por debajo Te mando un abrazo muy buena intención mejora algunas cosas el concepto lo tenes 🇺🇾
I think it’s a great built even if it’s not 100% it will work only thing I would add is interchangeable wheels for bigger sizes
Straight onto business. That's what I call a workshop
You've got every tools every piece wow 👍
Apesar de ser tão jovem, porém muito sábio e incrível a tua sabedoria além de ser super organizado. Está de parabéns você é um excelente profissional.
a very useful video, as long as people watch it, the more God's reward flows for you.
I make this sort of thing but I make sure the pry bar swings up and down for leverage. Plus there should be absolutely zero wobble, jiggle, so that all your kinetic energy goes into the bend. Also I use a really Stout long pry bar lever, makes it a cinch no struggle. Especially when you have to do hundreds and thousands of bends,💥 that's my two cents. Great job by the way. The next one I'm building, bends to solid bars at once.
Domaca pamet kad proradi iz radionice drago mi je kad vidim da neko radi sa apetitom vidi se da si perfekcionista nista ne prepustis slucaju.👍
Pozdrav iz Srbije
Potpuno se slazem da je veliko zadovoljstvo gledati mladog momka kako ima zelju i znanje za rad.
Ali od ovog momka bolji je momak na kanalu peChoO
No pues... tienes un buen de herramienta.
¡ Tienes una ferreteria!
Yo a luchas tengo unas pinzas ☹ .
Pero exelente trabajo 😀.
Me gustó lo que hiciste.
Very good. Then thinking of adding a big bottle jack with corded drill instead of a lever. Wanting to build my own exhaust system. Again thanks for posting.
Nice build. Only concern I have is the welded center pivot. The plating on those commercial bolts makes welding them sketchy. Make the center pivot 5mm longer and pass it through the baseplate, then weld the head from the other side. That will send the bending forces through the shank of the bolt into the baseplate, instead of through the welds on the sides of the bolt head.
I wasn't going to say anything, but with 7 million views, you have some responsibility to the people to be honest and point out that this does not work well and that it is far from idea. You are going to motivate people to purchase dies and materials to make this tool, and it will be a waste.
I can see from the video that the bends are not consistent (the radius is changing) and the bends are damaging the pipe, unlike a properly built bender. This was a fail, and should have been labeled as such... or at least pointed out that this was NOT idea and the results were not great. Instead you hyped it up like it all went to plan.
People. If you are going to bend different size pipe, you should be using the appropriate size die and follower. If you are going to bend more than one size of pipe with one bender, you need to have an adjustable follower or keep your follower close to the die to avoid kinking and other issues.
This would be a good video IF it didn't end giving the audience the idea that you can repeat this process and be happy with the results.
Excelente forma de trabajar voy a ordenado muy ordenado muy limpio tienes muy buena herramientas todo excelente lo único que faltó fue una base de cemento en el patio para colocar la curvadora saludos desde Colombia
Queria eu ter a metade das ferramentas que ele utilizou. Mas é inegável a habilidade do rapaz. Ficou muito bom o trabalho. Parabéns!!! Congratulations!!
Excellent!!! 😁👍Although, you might have to heat it with a torch to make it easier.
Exelente maestro, no le doy un aplauso sino un millon, felicidades
Como de llama ese material redondo que esa para doblar los tubos??
The video was quite cinematic as if someone had written the screenplay. Didn't skip a second like I do with most videos. A very interesting and informative one. Keep it up bro. GBU
Step 1 - have all the key expensive components of a retail bender tool...
The first construction of the new workshop, it is so much more rewarding to make your own tools 🛠
Ррр
П
Well done, in my opinion, you just needed to make a 90-degree fold and another 180 to see how the curves will be.
llllllll
7
Cho tôi hỏi ! Vì sao khi tôi uấn ống kém lại bị gẫy mà không giữ được độ tròn của ống ạ ...
@@cuongnguyenduy8141 .
Awesome! Im new to metal work... and would love a pipe bender... Gonna have to wait a whil longer before I can do anything like that!
welding on a wooden table is a bad idea bro!!! great bender
Boa tarde! Gostaria de ter muitas ferramentas assim... parabéns pra você!
Is this guy working inside a hardware store? 🤔
Good idea! Thanks for sharing. Keep safe. Watching here in Canada
Excellent presentation. The Lord God bless you in Jesus mighty name
I think ,it was a little bit to light .😁
But working good .👍
you need thicker plate and a more solid handle. a few more bends and its going to bend or break
You should install this in a separate solid metal stand.
Yet another DIY'er who uses a vernier gauge as a scriber... puts me off straight away.
Guess what.
There are cheap ones... you cannot believe how "common" this practice has become. Yes buy a cheap caliper instead of a scriber compass.
🙏Sir Excellent your job keep your blessing us 🙏 i from mumbai india
Dobra ideja,pravio sam sebi nesto slicno,ide to mnogo lakse uz grejanje
ua-cam.com/channels/6ioKYOovUi9r8h4orOQ8pQ.html
alguien q m proporcione el precio y en dónde la pueda conseguir vivo en Chalco estado de México x favor
Trebas ga malo preraditi,jer ovako mozes savijati cevi samo do odredjenog precnika(fi). Jedan roler si trebao napraviti da se moze štelovati pa tako da mozes savijati i deblje cevi. Inace korisna stvar. Pozz iz Srbije 👋
Smart and effective!
O
Hello Dr. Ds.
Do you can show us next time to produce a Homade Garden Wagon from Wood?
Big up from Germany !
Where did you get the roller dies frome i cant find those any where! Help!!!
CHECK A SCRAP METAL YARD, ALWAYS CHEAP FINDS! 🇺🇲👍✌️
i follow Leandro Torneiro, an brazilian maker doing this project and must tell, this tool is awesome!
Good videos tutorial next time boss 👍👍👍
Hey man great job but I see a problem it’s flexing needs more reinforced and needs to be mounted to concrete not a wooden workbench
LOOKS AND WORKS GREAT, THANKS FOR SHARING. CAN YOU MAKE A METAL ROLLER TO ROLL FLAT METAL PIECES? 🇺🇲🌞👍✌️
9oooo
good job but i believe heating it with heating torch helps a lot also
ALI JE LIDL PRAKSIDE PLAZMA DOBAR PRODUKT ALI GA VI PRIPOROČATE PROSIM odgovor i stvarno lepo delavnico imaš pozdrave iz Slovenie
Muy bueno y muchas gracias por este video maestro.
11:38
11:38
Tebi nikada nemoze biti dosadno,radis to sto volis a opt se zabavis,a i napravis nesto korisno.
0
Extremely good. Very beneficient.
.
Greetings, you can add a little bit of oil to make it easier to slide
This is fantastic, I wish to have a work shop like this with all these machinery, thanks for your good education. Watching from GH,
ฟฃฃวฃ
Easy when you got All the tools 😂
I made something like that for .500 tubing. Many years ago. I use a bearing on the small wheel. I Mande the wheels. I used a .500 wide tool bit. With the radius on it. Great job. Keep up your great work.
GOOD IDEA SO MUCH
MAX! Everytime I saw MAX! I said MAX!
How're Parkside plants?
Nice bender... Good job sir.
It looks like it's made for 1 size of Pipe only.The rear anchoring back U shaped plate should have been made to accomodate several different sizes.
Otherwise I like how it has degree markings capabilities.
the tools are complete.. thank for sharing
dads gonna be pissed ha ha bending his pipes up lol jp
Wow awesome build thks for shari ya dont need to be rocket scientist to do this great idea going to build oe great for building gocarts and Old School Choppers so from Canada 🇨🇦 SK later 😊ya got this 👍
Lealohi lensa amboru
Me watching this : he is a profesional 👍
Thanks 👍 Alhamdulillah
Great little project, nice finish. Great video, thanks. 😊
can you call it a home made??!!!
O garoto tem um aparato de Dar inveja
Zanimljiv video, odlična savijačica. S istom možeš si praviti vilice od rebrastog (šipki) željeza za armirani beton kod nadvoja, zidova, temelja i slično. Bravo Doctor. Veliki pozdrav!
Пп
My greeting from iraq
It’s practically a tubing cutter. Your tubing is marred up now. Thanks anyways
Fantastic!. But where to get those wheels?
Were you able to find any
@@johnnymcclurg9672 in a F1 race car?? 😋
Google Rollers with U Groove
Easy with all the tools and materials at hand.
kad ce vise video o bmw-u
Hi doctor i like this one's exterior design
Nice job.....would like to have one ...with variable clutches...
Bro I think you crazy and love with tools
Very nice
Красава , просто быстро и эффективно !!👍👍👍👍
you prolly dont give a damn but does someone know of a tool to get back into an instagram account..?
I stupidly lost the password. I would love any tricks you can offer me
@Jairo Jake instablaster =)
hello where did u get those bender dies/wheels please?
Отличная работа! Спасибо за видео!
Nice work idol
good idea, the only bad thing is the axis of the main mold welded to the plate and of greater diameter, the best would be past and thicker, it is observed how it moves by the applied force.
How do you make the dies?
Hello Doctor D S.
I'm Jessie from Philippines.
Nice work and video.
Will try to make this.
Useful for the beginners in DIY things.
Thank you for the informative video.
Great Job sir!
🙂👍
❤
Nice uploaded frends
Ottima costruzione, molto robusta, 👍👍
Intelligent. Boss. Realy
Good fabricator nice job.
love it your tools sir
Idées et conceptions très utiles, mains en l'air, salutations du Maroc
👍👍👍👍💯
Ijin nyimak bosq👍👍👍👍👍matap...❤❤❤❤👌🙏
Koju si školu završio
Thank you so much for this bender making technical education
Where did you get the wheels?
Dobra stvarčica samo tesko je savijat rucno 😂😂 vidim po tebi kak se naprezes da ne ide bas lako 🤣
thank you very much
If my grandma had this nice bending dies she would build it!
nope....just no. not a proper bender.
Is the pipe bent? Actually, yes, it IS a proper pipe bender!
Run of the mill build. Anyone with scrap pile and welder can build.. Real trick is where to get the round dies.
Day vise pricaj,ko se slaze neka stavi lajk,Dosadno je kad ne pricas!😨
YOU HAVE GOOD IDEAS I HAVE TO MAKE ONE MODIFY ON MY MOTORCYCLE ESCAPE HAVE A NICE WEEKEND MAN
not good
Amigo buen trabajo gracias por subirlo
1)la chapa de 6 mm es fina de 1/2 para arriba
2)los tornillos no sirven ejes de 40mm para arriba
3) perfora la chapa de 1/2 la que pongas de base los clavas y solas por debajo
Te mando un abrazo muy buena intención mejora algunas cosas el concepto lo tenes 🇺🇾
Where can someone by the round dye pieces at!!!???
Its like you have a hole store of new tools for your self