Hello everyone😁 The video about Tomos will wait because I went on vacation 😉 ... Pozdrav svima😁 Videozapis o Tomosu će pričekati jer sam otišao na odmor 😉
Instead of painting the revised bender head (brilliant manufacturing process with the bar-stock!!!) I would've nickel plated that naughty boy. Also I'd have done a little more fill welding & maybe a second layer of bar-stock on the underside. Just personal preference. GORGEOUS, though! 💖💖💖💖💖💖💖💖💖💖💖💖💖💖
Clever ideas ! As said below, you need to match perfectly the tube dimensions otherwise it gets somewhat flattened. Good quality pipe benders are horribly expensive unfortunately.
I’m an electrician, and we use a Greenlee hydraulic bender to bend larger EMT conduit/rigid. It has different size aluminum shoe’s that fit whatever size conduit you want to bend. If you don’t match it correctly, the conduit/pipe will pinch. Not sure if maintaining the inside diameters important for future projects, but if it is, you may want to look into that. This comments only a suggestion, to help on something I had to learn through hard knocks! It turned out great, see ya on the next one!🇺🇸
Electric Boat in Groton, CT cold bends 3 1/2" HY120 for submarine pressure hulls. This is for homemade DY's with nothing. Oh BTW did my time packing 5" rigid around @ 110LBS per piece, putting in a sub station tell us more about being a pipe bender.
Harbor Freight sells these for around $200. They use a molded cast iron piece for each size of pipe. I do not have one, but each time I see it in the store I tell myself that I should buy it. One of these I will buy one.
Projekt je odlican svaka cast... Inace prilikom savijanja cijevi zavaris na jednom kraju komad zeljeza i napunis cijev pijeskom do vrha i isto tako zavaris komad zeljeza da pjesak nemoze izlazit i tako savijas i cijev se nece tako ,,uvijat s unutarnje strane" i inat ces odlicne rezultate 👍😉
I nepotrebno ti je stavljati prijevod i na hrvatski, doviljno ti je samo napisati na engleskom i molim te koristi neke normalne fontove koji se lako čitaju... i ovo u doljnjem desnom kutu tvoj ig malo bode za oci probaj svoj ig rec na pocetku ili na kraju a ne ovako kroz cijeli video
it could be better if you fill the tube with sand and solder "close" it soldering tops. or with soapy water and freezing before bend it,it will maintain the inner dimensions better.
Good effort - but I know that it won't bend muffler tubing without crushing it,you need to fill it with wet sand but that method is labourious.Trev New Zealand
you could made round spacers from tick metal sheet and installed on plastic wheel from both sides and fastened firmly with bolts to prevent plastic wheel to deform
Still distorted the pipe too much to use for anything like a roll cage. It made the pipe too weak in the bend the way it flattened it out. But still good build for just a regular pipe bender.
just buy the 12 ton harbor freiight pipe bender and you get 6 dies up to 2" pipe for $140, other bender manufactures charge that much or more for one die
jedan mali savjet ako trošiš puno wd40 :D radim u autoindustriji i sve stupne bušilice, robotske ruke i slično koriste svinjsku mast za podmazivanje kod bušenja, urezivanja, narezivanja itd...naravno onu koja je neupotrebljiva za kulinarstvo...
Nisam znao za tebe dok nisam pogledao tvoje gostovanje u podcast inkubatoru. Kao ikako možeš i želiš, preporučam ti da upišeš strojarstvo ili elektrotehniku, ali ne radi diplome nego da ti se još dodatno prošire vidici. Ljudi koji su majstori i imaju inženjersko znanje su nezaustavljivi. LP
Hello everyone😁
The video about Tomos will wait because I went on vacation 😉
...
Pozdrav svima😁
Videozapis o Tomosu će pričekati jer sam otišao na odmor 😉
Di si na moru
Hello, the ALIEN head😂
Please make thanos infinity gauntlet
Ok brt sretno na odmoru
Okej lipo se provedi i ako si na moru iskupaj se pa kad se lipo vratis ako zelis snimi tomos.
Ja sam jucer svoj tomos doveo sa popravka i sad radi
Great idea, making mine out of scrap 2 x 4's for 3/8" rebar bender. Making circular crab traps is the project.
Instead of painting the revised bender head (brilliant manufacturing process with the bar-stock!!!) I would've nickel plated that naughty boy. Also I'd have done a little more fill welding & maybe a second layer of bar-stock on the underside. Just personal preference. GORGEOUS, though! 💖💖💖💖💖💖💖💖💖💖💖💖💖💖
The best idea I've ever seen on how to make a die to bend tubes without tools and hard to get. Nice job.
Why not take all the money spent on the metal and buy a bender
Clever ideas ! As said below, you need to match perfectly the tube dimensions otherwise it gets somewhat flattened.
Good quality pipe benders are horribly expensive unfortunately.
I’m an electrician, and we use a Greenlee hydraulic bender to bend larger EMT conduit/rigid. It has different size aluminum shoe’s that fit whatever size conduit you want to bend. If you don’t match it correctly, the conduit/pipe will pinch. Not sure if maintaining the inside diameters important for future projects, but if it is, you may want to look into that. This comments only a suggestion, to help on something I had to learn through hard knocks! It turned out great, see ya on the next one!🇺🇸
Ya I loved mine it was the 777 but someone wanted it worse than I did and stole it!
I hope Cavin will always succeed in innovating with works whose knowledge is useful for others.
Electric Boat in Groton, CT cold bends 3 1/2" HY120 for submarine pressure hulls. This is for homemade DY's with nothing. Oh BTW did my time packing 5" rigid around @ 110LBS per piece, putting in a sub station tell us more about being a pipe bender.
Harbor Freight sells these for around $200. They use a molded cast iron piece for each size of pipe. I do not have one, but each time I see it in the store I tell myself that I should buy it. One of these I will buy one.
i like the way the workshop is arranged
Very good thought!
Projekt je odlican svaka cast...
Inace prilikom savijanja cijevi zavaris na jednom kraju komad zeljeza i napunis cijev pijeskom do vrha i isto tako zavaris komad zeljeza da pjesak nemoze izlazit i tako savijas i cijev se nece tako ,,uvijat s unutarnje strane" i inat ces odlicne rezultate 👍😉
E i da, čuo sam i tu soluciju :D
Just a tip.
If you heat up place you need to bend, use flame torch.
lt would be much easier.
Best wishes.
Si fuera completamente sólido si, en este casi si lo calienta el material se hace más maleable y en vez de doblarse en grados se aplastaria el tubo
you need the same wheel but in reinforced steel and your machine gonna be awesome ! you can machine them in piece of steel excellent work !
Gledao sam te na tv nisam znao da si tolko dobar najboli si💪👋👍👍👍👍
Diresta.hr 😂👍👍👍
Gledam zadnjih par videa, poradio si malo i na produkciji 👍!
Još malo poradi na engleskom i bit ćeš top top 😂😂
Ma joj nez jos ni Hrvatski pricat a kamoli eng🤣🤣
@@DShomemade hahaha ajde mlad si, naučit ćeš 😂😂
I nepotrebno ti je stavljati prijevod i na hrvatski, doviljno ti je samo napisati na engleskom i molim te koristi neke normalne fontove koji se lako čitaju... i ovo u doljnjem desnom kutu tvoj ig malo bode za oci probaj svoj ig rec na pocetku ili na kraju a ne ovako kroz cijeli video
Hey! That was really clever! Congratulations
Svaka čast odličan projekt nego doktore šta se dešava sa tomosom
Srećan rođendan
Hvala ti ;)
C'est vraiment formidable
Bravo mladi čovjeće , za svaku pohvalu , samo hrabro !!!
😊
Clever and innovative 👍🏼
it could be better if you fill the tube with sand and solder "close" it soldering tops.
or with soapy water and freezing before bend it,it will maintain the inner dimensions better.
👍
Good effort - but I know that it won't bend muffler tubing without crushing it,you need to fill it with wet sand but that method is labourious.Trev New Zealand
Would anyone know where i could get hold of some of those rollers....good video👍👍
Why don' t you get dimensions for shoes and rollers on a greenlee 880 tube bender? It might help fix your problem.
Great idea Doctor , thank you for being share indeed
Glad you found an English comment ❤️❤️❤️
you could made round spacers from tick metal sheet and installed on plastic wheel from both sides and fastened firmly with bolts to prevent plastic wheel to deform
80 ok
Where roller did you buy those rollers?
Estoy sorprendido me gustó mucho creo haré una de estas es la mejor y mas sencilla de hacer .
Better than before...But not maksimal.
Best
Super siii 👍👋👋👋👋
Instead of welding all those small pieces of round rod, use a portion of a 12" or smaller wheel from a junkyard.
What is the distance between the two holes on the right and left of each steel tube and its diameter?thanks
Iam from indonesia
Good job boss
good morning you are great I liked it very happy to exist ask how do you thank you
Un Mexicano le gusto este vídeo
Molim te pretplati se na moj racun ja te obozavam i svaki video pogledam medu prvima
Pa di je sastavljanje tomosa?
Jddbf,😊
For it to bend well you need to put sand inside it.
Kad će video o tomosu?
12:24
Ono kad napravis projekt i bude neuspjesan
P
Top mano gostei da ora 👊 aqui do Brasil.
Très bon idée 😃😃super bien fait
Ok...ok...👍👍👍👍
Excelente video ,admirable el orden en el taller.
Brilliant well done love 💓 it
Svaka cast druze za projekt
thank you for the effort to help. us amateur welder like me from ph.
Kada ce serijal o tomosu?
Svi lajkk da vidii
God job bro,i from Malaysian
Druže svaka tebi čast, vidi se da si pravi majstor, imaš smisla, radionica je uglavnom čista. Sve pohvale
You tried dude but try to buy the main pulley I love your work keep it up
Svaka čast predobra ideja!!
Muy buenas ideas para tod@s
Teniendo la herramienta adecuada en cada momento.....
sir.,what gauge or size of the spring?
Gracias por compartir 👍😇🧐👍☕️🍪
Brilliant idea, erm judging by the holes in your shirt at the beginning of the vid you have spent a lot of time bending steel with your hands.
Still distorted the pipe too much to use for anything like a roll cage. It made the pipe too weak in the bend the way it flattened it out. But still good build for just a regular pipe bender.
LPS NEWS TODAY
snimaj cesce i pogoto tomosa, inace svaka cast vrhunski si majstorr
Master idea!!! Thanks!!!
Svaka čast na projektu mogao bi na vakav sličan način napraviti i hidraulični škrip (stegu) 💪💪 💪
👏👏👏👏
Predobri videi..samo nastavi😄
Great/amazing Sir👍
PAL, you just give me the "light", the idea to build mine, Thanks a LOT
Talented fabricator
Пластиковые пуансоны Товарищ Дью оценил бы))
just buy the 12 ton harbor freiight pipe bender and you get 6 dies up to 2" pipe for $140, other bender manufactures charge that much or more for one die
You are creative
Odlicano za dodat u radionu.
Amazing job sir
Пуансон , на один раз!
Thanks for sharing your idea. Only 45 degrees? Can you show to us 180 or 90 degrees?
CAN YOU use the same bending guides that they use on machines that bend exhaust pipes ?? I think its called a Mandrel Bender !!??
@Mike Cool ,thanks for that
Svaka ti čast izgleda kao kupovno
Pokušaj napraviti Iron Man Mark I odjelo, to bi bilo zanimljivo i gledano. 🙂💪💪💪
I saw you at podcast the other day, it was great :) I Respect your hard work, young man! Keep up the great work!
for the amout of money you have to pay to buy the steel, just buy the tool
Odlican video kao i uvijek!!
Kad ces nastaviti sa tomosom
Svaka čast.... Bravo.... Pitanje.... Gdje si nabavio dizalicu 20t?
Pozzz ;)
Znatpromet ;)
Great work..👍👍👍
Sta si koristio u predproslom klipu za skidanje farbe ona neka tečnost
Paint stripper 💁🏻♂️
Desitol ;)
Naparvi novi stol za radionicu jl ti se pigaju vec daske i za alat napravis jeedno mjesto a z boje i ostalo na drugo tako sam ja nalravio😁
How much did that flat bar cost
Cool idea👍😷
Good job sir
Ya get you measurements off the harbor freight one??!!☝️🤣
Muito bom parabéns tamos junto
jedan mali savjet ako trošiš puno wd40 :D radim u autoindustriji i sve stupne bušilice, robotske ruke i slično koriste svinjsku mast za podmazivanje kod bušenja, urezivanja, narezivanja itd...naravno onu koja je neupotrebljiva za kulinarstvo...
Nisam znao za tebe dok nisam pogledao tvoje gostovanje u podcast inkubatoru. Kao ikako možeš i želiš, preporučam ti da upišeš strojarstvo ili elektrotehniku, ali ne radi diplome nego da ti se još dodatno prošire vidici. Ljudi koji su majstori i imaju inženjersko znanje su nezaustavljivi. LP
Hvala ti ;)
Браво братишка. Я тоже поделюсь работой. Я электрончик
ma nema se šta tu više reči Doktorirao kao i svaki do sad projekat
Gde je Tomos
can i have the measurement or the dimensions of your project???
A staje s tomosom
Mucho trabajo de sobra
Svaka čast majstore
Dali možeš pokazati kako praviš ventilator
Lumayan utk pemula seperti kamu
Great job !