Bicycle Wheel Sealed Bearing Removal/Install: No Bearing tool!
Вставка
- Опубліковано 11 вер 2024
- I show you how to remove and install a sealed bicycle wheel bearing. This is a sealed bearing cartridge type bearing. No bearing tool needed just every day items around your garage. #shorts #bicycle #sealedbearings #youtubeshorts
Phil Wood Grease: amzn.to/44wfQYr
Park Cone Wrench Set: amzn.to/3O0kdns
We earn from qualified Amazon purchases with NO cost to you. ANY item that you need or were going to purchased anyway through any of our links, helps support this site. Thank you for your support!
If this video was helpful and saved you time and/or money, consider supporting the channel:
Hit the "Thanks" button above to leave a tip. Thank you!
WEBSITES:
classicjapanes...
pacelinebikes.com
SOCIAL MEDIA:
Instagram: / classic_japanese_bicycles
Twitter: / japanesebicycle
Facebook: / classicjapanbicycles
Pinterest: / bicyclerestorationman
SUBSCRIBE: bit.ly/Bicycle...
Here's another short you may like: ua-cam.com/users/shortsmGNeYUmVFF8?feature=share
Bro I felt that hammer hitting the finger
Not that bad! Thanks for the comment. 👍👊
Thanks so helpful 👍👍
Glad it helped thanks for the comment! 👍👊
I would use a large nut and bolt to press the bearings back on.
Good suggestion, thanks for the comment. 👍👊
Thank you friend, it's the best video from me
I'm glad you like it and thanks for the comment! 👍👊
How to insert the bearing to the right depth, only with a washer, you will not go deep enough ?
It actually places it even with outer edge of the hub.
My sealed bearings on my bob trailer are not turning well. The problem is that the axel is not removable.
Can you at least change the bearings?
I had thought remove axel , use a drift to knock out old bearing. The bearings must press in and trap the axil. So what's the trick??
I'm old and not as smart as I used to be. Woppes
Put the bearings in the freezer and use a torch or even a heat gun to warm up the axle where the bearing goes and it will fit right in
❤❤❤❤❤❤
Thanks for the like! 👍👊
Good method for Novatec HB series hubs .
Thanks for the comment Robert! 👊👍
Bonkers!
Thanks for the comment Robert! 👍👊
i have that same hub the question is how to remove the bearing cups?because i want to convert it to sealed bearings
Replied to your earlier request. Thank you. 👊👍
Is this bearing hub or converted from normal hub ?
This was not converted. It was always a sealed bearing hub. 👍👊
bearing size?
Sorry, don’t remember the size. The bike is in storage now.
Is the size of bearing same or varies from bicycle to bicycle
It can but since the axel is standard in these vintage bicycles I would imagine they're pretty much the same. Always measure the inside diameter of the middle hole and the outside diameter as well. Also measure the thickness. 👊👍
@@BicycleRestorationMan Thank you
@@venkateshshanbhag8310 anytime 👍👊
Bearing no?
Not sure what your asking.
@@BicycleRestorationMan means bearing's size?
@@gnjrastogi3085not sure of the bearing size.
What is the number of bearing
These are sealed bearings so there are 2, one on each side. Thanks for inquiry Michael. 👊👍
Good way to flat spot the bearings.
There being replaced! 👍👊
If the bearings are made of tinfoil 😆
The song ahhh 😻
Thanks for the like! 👍👊
You're welcome
Bearing number
The bike is in storage and I do not have any of those bearings around. Sorry.
А если ещё и подшипник с одной стороны разобрать и в него побольше смазки добавить, то это будет вечность.
That it would! 👍👊