Dear Sir, thanks for showing snippets of your lathe build. Excellent job. I liked the way you produced a headstock shaft with a bore, not solid. Do you happen to have plans… a) For further development like motorising drives and b) Actual plans for making another model of your design?
Interesting project but using pillow box bearings could be a problem they are totally inaccurate. Too much slop in that type of bearing should use a pair of angular contact ball bearings 72xx be type works for me!
Hi, purpose of the smaller rail set is for making cone and other stuff under some angle, whole plate with rails rotates around bolt in middle. Also so i can adjust paralelnes of machine. Thank you for watching! 😁
Really a nice job. All the right pieces including some that were not scrap. Very rigid. Two things we almost never see in this kind of DIY project: cost and precision. It would be very interesting to see the money spent on scrap metal and purchase parts, separated. Test precision by placing a ground round bar between centers and run a test indicator down the bar once along the top and again along the side.
Hello, total cost was around 600-700$ Chuck was 150$, rails around 250$, pulley around 25$ each and steel parts at scrapyard 150$ and a lot of screws... Best option for sure is to buy regular lathe😅 but i have realy small workshop and i dont need too high presition for my projects. Also regular cheapest normal sized lathe in my country is anywhere from 3000 to 5000$😅😅 Also thank you for commeting have an nice day!
@@davidwillard7334 ⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran
И не говоря о том, что в самоделке нихрена не отшлифовано и не отфрезеровано, никакой проверки на биение и параллельность, нет нормальной продольной и малой продольной подачи, нет ходового и винта и валика, нет нормалтной регулировки скоростей, нет лимбов
They told me that this system is not good as a lathe but only as a cnc. Working with steel it is very easy for everything to break because it has no cutting power and the system is destined to last very little as well as not being safe for safety. I am trying to partially replicate your project but everyone is not recommending it to me. Do you have any work that is a bit more strenuous in order to appreciate that everything works fine? Thank you in advance :)
Sounds like the factors you are discussing are rigidity and dampening. Yes, this type design would have poor dampening. However it lends itself to be epoxy granite filled which will solve that. Secondly is the cross slide. This setup will have limitations on the depth of cut you can take. You will need to be weary of tool pressure. Other ideas to improve rigidity would be square linear rails, 30-35mm would likely do or even better yet box ways but this requires a way to precision grind and/or scrape.
так этот станок без претензии на высокую точность, а значит и шабрить там смысла нет! рез чистый без биений, без дроблений, а что еще надо от самодельного станка...Там пришабривать бесполезно так как от сварки вся рама винтом и горбатая.
Where fine big huge piece of scrap like that? All the scrap I can find is just that, SCRAP. Not massive long untouched beams and sheets. Big stuff like that is not able to do anything with because it's part of a machine which hasn't been cut apart. Has to be cut small to be able to be put in some of the equipment at my local scrap yard. Your either very lucky or decieving us and buying the metal
Those are some good pieces of "scrap" metal✌️😂🤣💚🇬🇧🌱
Yeah I thought that. They don't look anything like the "scrap metal" I come across.
Veoma dobro odradeno! Pohvale mladom gospodinu!
"Very well done! Kudos to the young gentleman!"
Excelente trabajo!!! Muchas gracias!!!
Nice, but Maybe finish up all welding? 🤔Seems to be tacked at some places, it could be much more stable when welding it up
Good work,you can be proud of your work, looks nice.
Молодец😊
👍👍👍
Yeah, right - "scrap" metal - shiny rollers and guides from China.
Yeah? What, you want him fabricating linear rails himself?
@user-cg3em4cw4f No, just get quality stuff from Japsn, Korea, or the USA, which actually is built to specification and won't make a mess of his jobs.
@@dnomyarnostaw Ah, I took it as one of those comments complaining that technically the rollers weren't scrap. My bad, definitely true.
Главный параметр любого станка - это ЖЕСТКОСТЬ , а алюминиевые направляющие не могут обеспечить необходимую жесткость ....
Excelente diseño, y muy bien heho el montaje, muy ptofesional, 👍👍
Complimenti spettacolari...ma ti ricordo che il tornio ha anche la contropunta..la farai a suo tempo?
Good Work. Much better quality can be achieved using couple of tapper roller bearings in head stock!!
AND SUCH A HOME-MADE MACHINE CAN BE MUCH MORE THAN MANY PURCHASED. I KNOW FROM EXPERIENCE
Sempurna ! Saya sangat menyukainya !!!😍
bravo majstore,pozz iz Slovenije
Good 👍
Why so many dislikes? You done a great job mate
Very well thought out, designed and put together. You made it so anyone can make one. I'm curious though, do you ever plan on making plans available?
Dear Sir, thanks for showing snippets of your lathe build. Excellent job. I liked the way you produced a headstock shaft with a bore, not solid.
Do you happen to have plans…
a) For further development like motorising drives and
b) Actual plans for making another model of your design?
Nice job. We shared this video on our homemade tools forum this week 😎
Well done 👏 ,it's a commendable skill
Great thinking outside the box
welldone,
im impressed
Good job making it work with what you can afford or salvage! Kudos!
Making it happen!!!! :)
Excellent
You are awesome!
Parabéns ficou show de bola 👏👏👏👏👏
Estes trilhos, onde consigo comprar? Lojas etc.
what is the name of the aluminum elbow for the sliding rail? and where to buy it? You made it very well. thanks.
Boa tarde) vc faz desse torno pra vender? Valor????
Interesting project but using pillow box bearings could be a problem they are totally inaccurate. Too much slop in that type of bearing should use a pair of angular contact ball bearings 72xx be type works for me!
Good point……he does have a Precise lathe for close tolerance work so it doesn’t matter this is just a video not a do the build like this or else!
@@scor440 I can't stop laughing due to your comment 😂👍
Could you provide a link to the bearing you mention? I’d like to see how much more precise it is, and the price difference of course! Thanks!
Svaka čast
Svaka ti cast!
That's impressive my dude! Love it... I'll have to check it out in person ;)
Sure, naleti kad god hoces! :)
Esta super
En poco tiempo va sacar el doble provecho. Saludos
Show de bola ⚽️muito bom 👍👍👍👍👍
Where did you buy the ways? How do you lock the tool carriage down?
Very good
What is the purpose of the smaller (300mm) rails? Why it is not enough to have longer (lower) rails in left/right direction?
Hi, purpose of the smaller rail set is for making cone and other stuff under some angle, whole plate with rails rotates around bolt in middle. Also so i can adjust paralelnes of machine. Thank you for watching! 😁
So washing machine motor powers this? So household voltage?
Congratulations!!! That is a very beautifully built machine.
Maybe he did use some new parts but, what he did was really quite impressive.
Assalamu alaykum very good
Impressive!
Really a nice job. All the right pieces including some that were not scrap. Very rigid. Two things we almost never see in this kind of DIY project: cost and precision. It would be very interesting to see the money spent on scrap metal and purchase parts, separated. Test precision by placing a ground round bar between centers and run a test indicator down the bar once along the top and again along the side.
You always wonder ! What costs More !??
Hello, total cost was around 600-700$ Chuck was 150$, rails around 250$, pulley around 25$ each and steel parts at scrapyard 150$ and a lot of screws... Best option for sure is to buy regular lathe😅 but i have realy small workshop and i dont need too high presition for my projects. Also regular cheapest normal sized lathe in my country is anywhere from 3000 to 5000$😅😅 Also thank you for commeting have an nice day!
@@davidwillard7334 ⚠️ God has said in the Quran:
🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 )
🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 )
🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 )
🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 )
🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 )
⚠️ Quran
BG,,mantap,,,itu beli rel nya di mana
Great job
Is very good
Hello! What kind of bearings?
so where did you find scrap rails and screws?
And Welder ! / Rod ! Too ??
nice work
Как спустя год ведет себя станок, вылезли ли какие нето болячки?
Buy tabriz lath machine
This is the best machine factory in the world
Iranian lath machine are best
Very nice
Super 👍👍👍👏👏👏🇵🇱
Porque você não ensina como marcar os buracos da chapa p rolamento p dar certo
support to you friend
Bravooo e super strungul
How much sir
Di ti je ona iz lidla parkside stupna
Good
А регулировки были?
Indeed scrap metal 😂
Respect
Ukuruan panjang dan lebar jarak nya berapa ? Mohon di jawab terimakasih
Senapan pcp bikin bg
TOP PARABENS
Эти линейные подшипники очень слабые для станка, там пластмассовые детали, никогда не делайте так . Это не будет долго работать
И шпиндельные тоже.
И не говоря о том, что в самоделке нихрена не отшлифовано и не отфрезеровано, никакой проверки на биение и параллельность, нет нормальной продольной и малой продольной подачи, нет ходового и винта и валика, нет нормалтной регулировки скоростей, нет лимбов
ovako seksi video se retko vidja, pozdrav iz srbije
They told me that this system is not good as a lathe but only as a cnc. Working with steel it is very easy for everything to break because it has no cutting power and the system is destined to last very little as well as not being safe for safety. I am trying to partially replicate your project but everyone is not recommending it to me. Do you have any work that is a bit more strenuous in order to appreciate that everything works fine? Thank you in advance :)
Sounds like the factors you are discussing are rigidity and dampening. Yes, this type design would have poor dampening. However it lends itself to be epoxy granite filled which will solve that. Secondly is the cross slide. This setup will have limitations on the depth of cut you can take. You will need to be weary of tool pressure. Other ideas to improve rigidity would be square linear rails, 30-35mm would likely do or even better yet box ways but this requires a way to precision grind and/or scrape.
Хотя бы болгаркой пришабрил соприкосновение плоскостей профиля и направляющих, а то просто силой притянул их типа и так сойдёт...
так этот станок без претензии на высокую точность, а значит и шабрить там смысла нет! рез чистый без биений, без дроблений, а что еще надо от самодельного станка...Там пришабривать бесполезно так как от сварки вся рама винтом и горбатая.
Muito bom
Where fine big huge piece of scrap like that? All the scrap I can find is just that, SCRAP. Not massive long untouched beams and sheets. Big stuff like that is not able to do anything with because it's part of a machine which hasn't been cut apart. Has to be cut small to be able to be put in some of the equipment at my local scrap yard. Your either very lucky or decieving us and buying the metal
Інтересний станок,а розміри його можна.Дякую...
Convert into...CNC
okay, that SBR rails are scrap metal..
this lathe need tailstock)
Great video, disappointing that you say made from scrap but then you stick brand new inline rails on there.
that don't look like scrap metal to me..
Scrap huh,what is that about $5000 worth of scrap.if I had that kind of scrap I’d just go buy new lathe’s
What's the precision of your lathe?