Zero 10x LCD settings P1: lcd brightness P2: miles/kilometers P3: voltage (depends on scooter) P4: hibernation timer P5: P6: wheel diameter P7: number of magnets on the motor (don’t change) P8: limitation on power P9: kick or zero start P10: P11: electronic breaking 1-5 P12: soft or high acceleration 1-5 P13: P14: P15: cut of voltage (don’t change) P16: zeroing the km counter P17: cruise control (on=001) P18: P19: P20:
When i set P9 to push to start mode, it is ok until i turn unit off then back on it reverts to 0 which means when you touch the throttle it wants to move, any ideas, Thanks.
Try doing this again and after changing the setting, back out of the settings by holding power and mode. Then the setting should save. If this does not work contact us at service@revrides.com . Safe riding!
is there a setting for battery percentage? I have a scooter with the same Indicator panel, I run about 25km still the battery indicator is still full charge, but then suddenly it wont start and i quess its low bat. is there a way to calibrate the battery bar or percentage?
Thanks for this information. May I ask if you can show how to properly lock the Evercrosss scooter H5. If you chose to not attach the seat. Also do the wheels need to be filled with air? Or are they solid plastic?
hey my zero 8 only charges max up to 4 out of 5 bars and =50.2V. I'm talking when the green light on the charging brick turns green. So is it blocked to max 80% charge to preserve the battery life?
Hi, i have a question, when i enter the P settings and long push the on/off button, the letter ''A'' on the bottom left changes to the letter ''d'' And I wondered what it does... so if you know please tell me :)
Hey! Thank You for the information! But unfortunately I didn’t find what I need, my LCD display doesn’t show my battery right, just full or empty, any configuration for this? Cheers
It is possibly on kick start. If so, you will need to kick off i order for throttle to work. If you want to change that setting, P9 will let you enable/disable it.
hi tnx for the guide. when i in the settings menu (p-settings) , and i long press the power button, the "A" in the bottom line changes to "D". do you know what is the purpose of this mode A/D ?
Hello i have my techlife x7s scooter and batery when was new i was going around 50 km.. Now i see how is drain faster now i can go only 40 km... I done on it 3700km..... So my battery gonna be more bad till it die or i will gona have only 10 km range at end?
@@RevRides360 I see. Never mind. It’s Under voltage cut off to protect your motors from under voltage. If you let it rip while your 60v scooter is under 48 volts bad stuff can happen. 31.5 is a example the users manual gives. And I’m seeing riders setting theirs to 31.5. Their scooter won’t last long lol
@@RevRides360 I’ve had a lot of scooters, the Fieabor Q08p is the probably the best thing that happened to the scooter community, for $1300 the force behind this thing is INSANE
Thank you so much for the video my problem is that despite changing it every time. WhebI turn off my scooter it just keeps resetting to its original settings how do I make it permanent?
The red triangle usually means the brake levers are pulled. If you are seeing this flashing without the levers pulled, it could be a wiring issue at the brake lever area, or require some lubricant on the levers and sensors inside the levers.
Hello Tyler, thanks for the information. I have a Dualtron scooter with MR-100 throttle body. For some reason it just stopped working. Like a fuse was blown. Do these controllers have a replacable fuse? Or do I need to replace the MR-100. Thank you for your help.
Hello thanks from your information I followed you but happen something zero 10x when I riding it go automatic pleas tell me how can settle that thanks a lot
Hello, from Colombia. Is this screen and the entire scooter waterproof? Does the scooter resist use in the rain? Here in the tropical zone, it rains a lot. And we want to know if they have damage when driving in the rain
Gonzalo Gabriel Gonzalez Cano I have an 8 and it says do not use in wet conditions, but I saw a video of someone attempting to make theirs waterproof with some silicone or something I want to try it out
Yo también soy de Colombia, que tipo de scooter tiene? En general es mejor que ninguna las meta al agua ni siquiera en lluvia o charcos, siempre se terminan dañando aunque digan que son IP54 de resistencia al agua y polvo
Hello, I got the same scooter-same screen, anyways I have a problem in which the underlights when turning on the lights get purple, green and blue. Any idea how to fix it?
Hey! Sounds like there's an issue with the backlight on your display. Usually the throttle ends up needing to be replaced, as the backlight is not repairable.
So how do i set a complete Max speed on my Zero 10X to a complete Max of 30 kmph no matter what gear I’m in?! I’m tired of having to manually keep the speed down with police around
Ii have an Evercross H2 and ordered a compatible size and voltage as my old one. When I replaced the Battery and charged it up, It did not run as fast as before, Like 1/3 power was gone. Then I thought I would re install the old battery to see what the difference actually was and now It did the same thing when i reconnected it. I have two of these scooters so I compared the settings between both P settings and they are still the same. There must be another setting that was lost when the power was removed. Do you have any Idea?
hello .. I have the FH100 model which is practically the same, maybe yours has some more functions. Have you tried to hold down only the MODE button? A blue spotlight appears on mine, do you know what it is for? thanks bye
Also, since you're an expert, HOW to get the right brakes? I have the generic Chinese red scooter you see everywhere these days. The brakes went soft and I took it to a shop. They changed the handles and "Bleed" it, etc.... It went flat again 2 times. I think is time to get cable brakes like the old bikes. I cant deal with this anymore... Any advice?
Hi Tyler, I changed my front tube on my Zero10x and refitted as per your video. Now the hydraulic front brakes are not working. I get a read warning sign top right on the LCD next to the gears. Any ideas how to fix this?
Tyler I have a evercross h4 scooter thanks for the guide however my settings will not stay after I program them in. The scooter resets once I turn off the key. Is their something I'm missing.
Yeah sounds like something is definitely missing my friend, your wee lil brain is missing its screws, so my guess is ur melon is just filled with useless meaningless thoughts and brain matter swooshing around and around with no end in site,,, my opinion is your pretty much fucked for life, man......tough break, I feel for ya buddy
Io ho questo computer qs-s4 e monto una batteria Lg 72v 32ah monopattino zero11x P03 - Voltage level of machine 72 giusto ? e P15 - Controller cutoff voltage?
Hello, The mechanic from our store is repairing a Kaabo Mantis 10+ and he wants to know if the percentage that is written on the scooter's screen means the percentage of battery left or the consumed percentage of the battery. I'll be waiting for your reply, Simon TurboKids Québec,Qc
Thanx for the video brother..I replaced the battery for my scooter and the display is not reading that the battery is full....tested battery output..tested output from bms with different meters and it shows 58V but my display only shows 56V and capacity only shows 50%..Thank You
Hello Rev Riders, hope everyones very well, just wanna ask maybe you happened to know about the default settings for Zero 10X, 52V, 23AH (P07 Number of magnets on the motor?) & (P15 what is the Cutoff Voltage? please let me know, thank you very much!
Hi there , how long before an app like the xaiomi 365 has ? It tells so much useful info even individual parallel cell voltage . a xaiomi bms could be piggybacked and then many of the app functions will work.
Hey mate solid video, my speedo isn’t accurate and I’ve done the wheel size to 10 and that’s all good but I’m going 30mph and it says I’m going 3mph just really confused done all the research but I can’t find anything. Thanks
I got a new e scooter, it was fully charged. And then i changed the volts from 36 to 60. And after that, the battery sign on the screen keeps blinking and only showing 1 bar. Do you know why that is? Also mine skips over some settings in the p menu
The volts of your scooter cannot be changed in the LCD. The Volts are determined by the battery. Please set the LCD voltage to be the volts that match the battery in your scooter.
Wait, so does P08 allow to save battery and increase range (sacrificing aceleration, of course) by limiting how much power can be drawn or is it something else?
Is it possible to increase top speed by changing tire diameter settings? I have 10 inches tires on my zero 10x what happens if i set it like 8 inches? I dont care what im seeing on panel i care about real gps speed
Thanks for reaching out! Unfortunately all that will do is confuse the device and not be able to properly read your mileage travelled. Hope this helps!
@@RevRides360 my turbo lightning plus has a error code e07. I was going down a hill for a while and all the sudden the scooter wouldn’t work. Any suggestions. Thanks.
Hey please help me, i have the zero 10x and Under the cable shield in the handlebars there is a wire inside which there are 3 wires inside of him: red, green and black and they were wrapped in white tape in a bad way so I wanted to replace the tape and then suddenly the scooter stopped working and did not open again... please tell me what to do if you .
i think so. i didnt fully understand your question but there in a setting that you can configure how much power you are using (in percent) so your scooter stock could be set at about 80 percent power you can configure it to be at a 100 percent. hpe this helps!
My scooter has a code that allows you access the P settings. Simply pressing the 2 buttons doesn't do it. I got the code , but once I enter the digits it doesn't automatically go to P...not sure what I am supposed to press next
Hi can anyone help with my 11X please? What exactly is the voltage cut-off and why is it set at 52 V when it's 72 V?? Unsure why and of the cut-off purpose. Also, what should the magnetic setting be set to and why. Thanks for your help in advance.
The “cutoff voltage” is for when the battery reachers 52v to save the battery so it doesn’t wreck the battery. If you haven’t changed the magnet settings they don’t need to be messed around with at all unless you have messed with them
First of all , many many thanks for this great video mate ! Just got Zero X and I would love to make settings, but unfortunately when I press this 2 bottom together instead of P mode comes number 50 and asks some code , do you have any idea what can be ?
Hey I got a problem with mine that it's only showing 3mph when before when it was in Kph an you pressed throttle it showed max speed.. when riding it though definitely doesn't feel like 3mph.. iv double checked settings and im sure everything is as it should be.. 🤔
@@RevRides360 thanks do you think they use this regarding regulations in my country to prevent increasing max speed ? In this case I don't think they Will share the code with me.
So I have the same Throttle and LCD options and when I first received the scooter I was attempting to change it from kilometers to MPH and not sure what I did but now instead of 1-3 gears it added 2. So now it's 1st through 5th. Do you know what I hit and does this really have any affect because it doesn't seem like it to me. Thanks
Hello everyone. I need advice. I have Display LH-100 on scooter FLJ K6. I don't know how to reset the ODO meter to P16. I hold down the MOD for more than 5sec. Nothing resets. I disconnect the hard reset connector. Nothing resets. The ODO meter had 8km on the display after unpacking the scooter.
Hi, I’m trying to decide which scooter to buy. I like the Fiebor QO6. But it’s a kick to start. That’s a deal breaker. Do you know if I’ll be able to change that in P settings? Ty
Any idea how the cruise control works? Does it require to maintain a certain speed for the X amount of time or the accelerator to be held an X amount of time? I have the LH-100 and assuming its pretty much the same in this one but i havent gotten much sense of it. Certainly not 10 seconds. More like 5. Its just real weird since sometimes it seems to activate after like 4 seconds and sometimes it wont...
Zero 10x LCD settings
P1: lcd brightness
P2: miles/kilometers
P3: voltage (depends on scooter)
P4: hibernation timer
P5:
P6: wheel diameter
P7: number of magnets on the motor (don’t change)
P8: limitation on power
P9: kick or zero start
P10:
P11: electronic breaking 1-5
P12: soft or high acceleration 1-5
P13:
P14:
P15: cut of voltage (don’t change)
P16: zeroing the km counter
P17: cruise control (on=001)
P18:
P19:
P20:
Thanks a LOT for the information. It helped me a LOT💯💯💯
Thanks for the info 😊
I can't get the accelerator to go, what settings do I use
Hi, difference from A and d if you press red button for 2 sec?then p15 voltage setting of mine is 39!it s ok?zero 8 41v 10Ah, thank you!!
Is the settings same on 8x?
Hi i would like to set
P11 and P12 to 5 (electronic breaking and acceleration ) is it can harm the z10 motor or the battery?
Hi Boris, You can definitely up you braking and acceleration! Ride Safe!
When i set P9 to push to start mode, it is ok until i turn unit off then back on it reverts to 0 which means when you touch the throttle it wants to move, any ideas, Thanks.
Try doing this again and after changing the setting, back out of the settings by holding power and mode. Then the setting should save. If this does not work contact us at service@revrides.com . Safe riding!
Thank you REV Rides, solved my problem, 😎👍
What does the little warning light that comes on the LCD display mean when you hit the brakes it comes on
Good evening, how to remove security please because I have to go with it to work thank you for responding quickly.
is there a setting for battery percentage? I have a scooter with the same Indicator panel, I run about 25km still the battery indicator is still full charge, but then suddenly it wont start and i quess its low bat. is there a way to calibrate the battery bar or percentage?
Its tha same to X10 too ?
Yes but the setting will vary per scooter. Be sure to look at your guide for exact specifications.
Thanks for this information. May I ask if you can show how to properly lock the Evercrosss scooter H5. If you chose to not attach the seat. Also do the wheels need to be filled with air? Or are they solid plastic?
Thanks for reaching out to REV Rides! Feel free to send us an email at Service@REVRides.com for further assistance. Cheers!
hey my zero 8 only charges max up to 4 out of 5 bars and =50.2V. I'm talking when the green light on the charging brick turns green. So is it blocked to max 80% charge to preserve the battery life?
Make sure and check your p-settings are correct
Just bought a Zero 9 and Im glad I saw this video. This wasn’t included in the instructions manual.
Hi, i have a question, when i enter the P settings and long push the on/off button, the letter ''A'' on the bottom left changes to the letter ''d'' And I wondered what it does... so if you know please tell me :)
any informations now?
i dont think there is any change with a or d
Hey! Thank You for the information!
But unfortunately I didn’t find what I need, my LCD display doesn’t show my battery right, just full or empty, any configuration for this?
Cheers
Excuse me, did you find the solution for this?
@@IM_A_PATRIOT not
i bought now new one..but why not working the accelerator but the power is on .iys not running .can u help me whats the set up to accelerate again
It is possibly on kick start. If so, you will need to kick off i order for throttle to work. If you want to change that setting, P9 will let you enable/disable it.
hi tnx for the guide. when i in the settings menu (p-settings) , and i long press the power button, the "A" in the bottom line changes to "D". do you know what is the purpose of this mode A/D ?
Great tutorial bro. How do I turn the flashing side leds off please?
I'd like to know how to turn them off and on
Hold the mode button for 3-5sec
Hello i have my techlife x7s scooter and batery when was new i was going around 50 km.. Now i see how is drain faster now i can go only 40 km... I done on it 3700km..... So my battery gonna be more bad till it die or i will gona have only 10 km range at end?
I have a 60 volt scooter. It came set at 31.5. Do I wanna set it at 60?
It depends on what model and lcd you have
@@RevRides360 I see. Never mind. It’s Under voltage cut off to protect your motors from under voltage. If you let it rip while your 60v scooter is under 48 volts bad stuff can happen. 31.5 is a example the users manual gives. And I’m seeing riders setting theirs to 31.5. Their scooter won’t last long lol
@@RevRides360 I’ve had a lot of scooters, the Fieabor Q08p is the probably the best thing that happened to the scooter community, for $1300 the force behind this thing is INSANE
Thank you so much for the video my problem is that despite changing it every time. WhebI turn off my scooter it just keeps resetting to its original settings how do I make it permanent?
Whenever I press the go button there’s a red triangle that comes up help and how do you fix it ASAP
Are you fixed this?
sosadacap no mate
The red triangle usually means the brake levers are pulled. If you are seeing this flashing without the levers pulled, it could be a wiring issue at the brake lever area, or require some lubricant on the levers and sensors inside the levers.
Hello Tyler, thanks for the information. I have a Dualtron scooter with MR-100 throttle body. For some reason it just stopped working. Like a fuse was blown. Do these controllers have a replacable fuse? Or do I need to replace the MR-100. Thank you for your help.
would need to replace.
Hello thanks from your information I followed you but happen something zero 10x when I riding it go automatic pleas tell me how can settle that thanks a lot
Feel free to go to the website and click contact us and send us details
Hello, from Colombia.
Is this screen and the entire scooter waterproof?
Does the scooter resist use in the rain? Here in the tropical zone, it rains a lot. And we want to know if they have damage when driving in the rain
Gonzalo Gabriel Gonzalez Cano I have an 8 and it says do not use in wet conditions,
but I saw a video of someone attempting to make theirs waterproof with some silicone or something
I want to try it out
Would be really nice if it was water proof out of the box
Yo también soy de Colombia, que tipo de scooter tiene? En general es mejor que ninguna las meta al agua ni siquiera en lluvia o charcos, siempre se terminan dañando aunque digan que son IP54 de resistencia al agua y polvo
Hello, I got the same scooter-same screen, anyways I have a problem in which the underlights when turning on the lights get purple, green and blue. Any idea how to fix it?
Hey! Sounds like there's an issue with the backlight on your display. Usually the throttle ends up needing to be replaced, as the backlight is not repairable.
Can you please explain what p8 actually does? Limitation of power how and why if there’s another parameter for 1-5 setting for acceleration?
We are happy to help you with understanding the settings of the scooter. Please call customer service at 360-888-7433 for assistance
So how do i set a complete Max speed on my Zero 10X to a complete Max of 30 kmph no matter what gear I’m in?! I’m tired of having to manually keep the speed down with police around
Ii have an Evercross H2 and ordered a compatible size and voltage as my old one. When I replaced the Battery and charged it up, It did not run as fast as before, Like 1/3 power was gone. Then I thought I would re install the old battery to see what the difference actually was and now It did the same thing when i reconnected it. I have two of these scooters so I compared the settings between both P settings and they are still the same. There must be another setting that was lost when the power was removed. Do you have any Idea?
My man! This is exactly what I was searching for. Clearly explained and easy to follow. Just set mine up as u recommended. Legend! Cheers!
Unfortunately I crashed and now its playing up. Just wondering if there is any way of reseting the controller.
What is setting 20? Where can i find list of numbers and their meanings?
Do they have gps tracker on them 🤔
No sadly
How can I make it auto gear 3 when i turn it on
when i turn it on it is always on 1¨
Unfortunately they are always set to 1
Ok:)
what would make my ebike take off as soon as i power on the ebike without the throttle being engaged and the throttle dont work when i do engage it
Thanks very much if you wanted to change the speed setting what would it be for 25km/hr or 15.5mph
hello .. I have the FH100 model which is practically the same, maybe yours has some more functions. Have you tried to hold down only the MODE button? A blue spotlight appears on mine, do you know what it is for? thanks bye
What is the 48v 500w rear motor electric scooter P15 voltage setting, please I changed it by mistake and now I don't remember.
39 Volts!
Also, since you're an expert,
HOW to get the right brakes?
I have the generic Chinese red scooter you see everywhere these days.
The brakes went soft and I took it to a shop. They changed the handles and "Bleed" it, etc.... It went flat again 2 times.
I think is time to get cable brakes like the old bikes. I cant deal with this anymore...
Any advice?
bleed the system sounds like something is leaking
Mines different. I don't have a p8 it just goes from 7 to 9 and I don't have a few others. It jumps to 99. Im confused
You may have a different LCD
Hi Tyler, I changed my front tube on my Zero10x and refitted as per your video. Now the hydraulic front brakes are not working. I get a read warning sign top right on the LCD next to the gears. Any ideas how to fix this?
need to know evercross h5 electric scooter any tips on changing speed..Great tutorial
Thanks for reaching out to REV Rides! Feel free to reach out to Service@REVRides.com for further assistance.
The kugoo m4 pro has an identical display, does this mean the options are the same??
We don't sell those, so we can't be for certain. What model number is on the display?
@@RevRides360 tf-100, says ao 185 on start up
Tyler I have a evercross h4 scooter thanks for the guide however my settings will not stay after I program them in. The scooter resets once I turn off the key. Is their something I'm missing.
Not all scooters are the same. I would contact the seller and get helped out. Cheers.
Yeah sounds like something is definitely missing my friend, your wee lil brain is missing its screws, so my guess is ur melon is just filled with useless meaningless thoughts and brain matter swooshing around and around with no end in site,,, my opinion is your pretty much fucked for life, man......tough break, I feel for ya buddy
If my scooter is on 52 volt, am I change it to 60v if it’s rated for 60v?
Thanks for this video. For the Zero 9, is it possible to turn off the blue LED lights when turning on the regular lights?
At this time there is no option to disable the blue LEDs while the headlights are on.
Io ho questo computer qs-s4 e monto una batteria Lg 72v 32ah monopattino zero11x P03 - Voltage level of machine 72 giusto ? e P15 - Controller cutoff voltage?
The motor is not working on mine and I’m getting an E9 flashing with a caution sign on the controls. Any suggestions?
controller fault needs a controller or bad connection
the display for battery is only showing 2 bars but battery is fully charged can you help please any ideas thanks ?
Which p setting is to make the scooter faster. I did it but not sure what setting please help
I have the plug scooter same set up tho
Hello,
The mechanic from our store is repairing a Kaabo Mantis 10+ and he wants to know if the percentage that is written on the scooter's screen means the percentage of battery left or the consumed percentage of the battery.
I'll be waiting for your reply,
Simon
TurboKids
Québec,Qc
Thanx for the video brother..I replaced the battery for my scooter and the display is not reading that the battery is full....tested battery output..tested output from bms with different meters and it shows 58V but my display only shows 56V and capacity only shows 50%..Thank You
Thanks for checking out the video! for any service inquiries please send an email to service @revrides.com!
My battery on mine always says it’s fully charged any suggestions?
Make sure your P3 is correct for the voltage of your scooter. 48, 52 or 60
please the PAS is not working with this controller ? what is the reason , i used 3 different pas and not working , thank you
Hello Rev Riders, hope everyones very well, just wanna ask maybe you happened to know about the default settings for Zero 10X, 52V, 23AH (P07 Number of magnets on the motor?) & (P15 what is the Cutoff Voltage? please let me know, thank you very much!
P07 = 28 magnets. P15 = 42V (some say 41V, depends on who you ask).
Thank you very much REV youre Awesome! more power to you guys👌👍👍
Cheers been wondering how to turn cruise control off it gets a bit sketchy at higher speeds
Thanks for the presentation. Is the electronic brake charging the battery?
Also do you know where to get replacement brakes. (Handle is soft)_
braking does not REgen charges
Hi there , how long before an app like the xaiomi 365 has ? It tells so much useful info even individual parallel cell voltage . a xaiomi bms could be piggybacked and then many of the app functions will work.
Hey mate solid video, my speedo isn’t accurate and I’ve done the wheel size to 10 and that’s all good but I’m going 30mph and it says I’m going 3mph just really confused done all the research but I can’t find anything. Thanks
May someone helpe you
I don't have P8 power level. But the P15 is 100. By any chance the power level is P15? Then again i don't have Cut off voltage. Kindly advise.
THe voltage setting.
I bought a used 10x that has the voltage set to 48. Does that make a difference? What is the diff between 48-52
Hello, my scooter only moves when I push it, can you help me
Hello please contact service@revrides for assistance!
Thanks for the tips, but I realized theirs a USB port on the LCD unit what is that for?
Thanks
Charging your phone
@@saltydegen correct for reference to others, measured 0.47 amps @ 4.78 volts with iphone connected using in-line usb meter.
I got a new e scooter, it was fully charged. And then i changed the volts from 36 to 60. And after that, the battery sign on the screen keeps blinking and only showing 1 bar.
Do you know why that is?
Also mine skips over some settings in the p menu
The volts of your scooter cannot be changed in the LCD. The Volts are determined by the battery. Please set the LCD voltage to be the volts that match the battery in your scooter.
Does this video only pertain to yoo or ur brand of scooter?? Just bought an EVERCROSS H5. And only have like maybe 6 P-settings
Great info.....does this go for the blue jx-168 model
Wait, so does P08 allow to save battery and increase range (sacrificing aceleration, of course) by limiting how much power can be drawn or is it something else?
Hi sir,can i install ignition key with volt meter,because my throttle is the same on your scooter.
I have a mototech thor 60v 2400w scooter and someone messed with the P settings and im trying to get the right settings! Could you help me ? Please
Hi I try P16 to reset the KM nothing happen same KM show me it’s not 0 and now ?
Is it possible to increase top speed by changing tire diameter settings? I have 10 inches tires on my zero 10x what happens if i set it like 8 inches? I dont care what im seeing on panel i care about real gps speed
Thanks for reaching out! Unfortunately all that will do is confuse the device and not be able to properly read your mileage travelled. Hope this helps!
Is lh-100 same as this what u showing?
Is there a reset button to make the settings go to default? Or back to factory settings
there is not
Hey
ive tried to change the settings
but the mode button seems not to be working on setting mode.
i cant change anything, only scroll threw the menu
What is the letters and numbers on the front of your LCD screen. Should be QS-S4 or TF-100.
no one has the gt 100 menu, do you have it?
what if my settings won't save?
Good morning just asking my zero 9 get slower while I'm on it riding for free wheel 50 km what can I do
Some P modes not appear on My settings like the 1st one, brightness set, just skip to P2, You know how to unlock or restore factory settings? Thanks
Hey, we have never seen that issue. Does your LCD say”QS-S4” on the front of it? Where did you purchase from?
@@RevRides360 my turbo lightning plus has a error code e07. I was going down a hill for a while and all the sudden the scooter wouldn’t work. Any suggestions. Thanks.
Hey please help me, i have the zero 10x and Under the cable shield in the handlebars there is a wire inside which there are 3 wires inside of him: red, green and black and they were wrapped in white tape in a bad way so I wanted to replace the tape and then suddenly the scooter stopped working and did not open again... please tell me what to do if you .
I recommend contacting your dealer. They are the best equipped to help you. Cheers!
Hello!
Its a option tha can i change my speed limited ,to have no limit speed on my schooter? (to be faster)
i think so. i didnt fully understand your question but there in a setting that you can configure how much power you are using (in percent) so your scooter stock could be set at about 80 percent power you can configure it to be at a 100 percent. hpe this helps!
@@avdikslv how
@@Nhzd just search on youtube: zero 10x scooter settings
My scooter has a code that allows you access the P settings. Simply pressing the 2 buttons doesn't do it. I got the code , but once I enter the digits it doesn't automatically go to P...not sure what I am supposed to press next
Feel free to reach out to us at Service@REVRides.com for further assistance!
Hi can anyone help with my 11X please? What exactly is the voltage cut-off and why is it set at 52 V when it's 72 V?? Unsure why and of the cut-off purpose. Also, what should the magnetic setting be set to and why. Thanks for your help in advance.
The “cutoff voltage” is for when the battery reachers 52v to save the battery so it doesn’t wreck the battery. If you haven’t changed the magnet settings they don’t need to be messed around with at all unless you have messed with them
I would like to limit my Zero 10 speeds from gears 1=28kmh 2=45kmh 3=50kmh to 1=28kmh 2=35kmh 3=45kmh. Is that possible?
Is this the same on kugoo m4
I just buy x1 pro v2 scooter but don’t know why can’t turn it on 🥺
Hi I wonder if you could possibly help me with the P Settings for my 11X. A detailed reply as to what yours is would be super. Thanks in advance.
All our customers get a detailed P settings guide in their box. Please contact your dealer.
How do I limit the speed to lets say 20km/h regardless of power output. Which program is that?
Can you teach me how to install ignition key with volt meter please.
First of all , many many thanks for this great video mate !
Just got Zero X and I would love to make settings, but unfortunately when I press this 2 bottom together instead of P mode comes number 50 and asks some code , do you have any idea what can be ?
For further assistance, follow up with us via email (Service@REVRides.com). Have a great day!
try 5252
Finally I found a video explaining this. I probably have everything screwed up right now
Good day guys! If your scooter is 60v should the P3 setting be set at 60v? And whats the purpose of it that u can change to lower volt and still runs
Yes this will make sure that your battery read out is correct and the scooter does not die early or allow the battery to go under voltage.
my control is showing me a ! (danger/emergency?)
it was after a minor accident, and now it doesn't let me give acceleration. any idea ??
For further assistance, reach out to us via email (Service@REVRides.com) with photos of what you are seeing.
Hey I got a problem with mine that it's only showing 3mph when before when it was in Kph an you pressed throttle it showed max speed.. when riding it though definitely doesn't feel like 3mph.. iv double checked settings and im sure everything is as it should be.. 🤔
Thank you for reaching out! Feel free to follow up with us at Service@REVRides.com with any troubleshooting inquiries! Cheers!
Hi I've the zero9 it ask for a pin code when trying to enter the P menu is it a factory setting ?
That odd. I would contact the place you purchased from and see if they can assist you. We do not have pin code's on ours.
@@RevRides360 thanks do you think they use this regarding regulations in my country to prevent increasing max speed ? In this case I don't think they Will share the code with me.
So I have the same Throttle and LCD options and when I first received the scooter I was attempting to change it from kilometers to MPH and not sure what I did but now instead of 1-3 gears it added 2. So now it's 1st through 5th. Do you know what I hit and does this really have any affect because it doesn't seem like it to me. Thanks
same i have 5gears..do you find a a fix?
@@kaanyharamy8157 you have to change the gear setting back to 3
no chance bro
Hello everyone. I need advice. I have Display LH-100 on scooter FLJ K6. I don't know how to reset the ODO meter to P16. I hold down the MOD for more than 5sec. Nothing resets. I disconnect the hard reset connector. Nothing resets. The ODO meter had 8km on the display after unpacking the scooter.
Hi, I’m trying to decide which scooter to buy. I like the Fiebor QO6. But it’s a kick to start. That’s a deal breaker. Do you know if I’ll be able to change that in P settings? Ty
Hi Rev Rides. ¿These settings must be change in 3rd gear?
Champion - thank you - i nearly had the scooter run away from me today and wanted kick to start on - you gave me the info that the manual didnt.
So on 15 mine is set on 39.0 cause it kind feel like my battery life is a lil shorten when riding around on gear 3 for like 5-10 min what should i do
Thanks for your comment! Please contact us at Service@revrides.com.
I have a question please how do u reset one of them?? as i have a error code
Any idea how the cruise control works? Does it require to maintain a certain speed for the X amount of time or the accelerator to be held an X amount of time? I have the LH-100 and assuming its pretty much the same in this one but i havent gotten much sense of it. Certainly not 10 seconds. More like 5. Its just real weird since sometimes it seems to activate after like 4 seconds and sometimes it wont...
Thanks for reaching out! Feel free to reach out to Service@REVRides.com more information and assitance! Cheers!
How do u get rid of red triangle warning light my scooter won't run