Thank you so much, I searched for this and found the old password which obviously didn't work and was sooo disappointed I wanted to return it and go for a refund. I have the Mantis 10 v2 and it is now a delight to ride....once again well done, please keep up with your answer to the nanny states.
Any idea how I can setup the LT01 to have different speeds in the 3 gears. At max or above 70(P9) I can see a difference but if I set it lower while trying to get gear 1 to max out at 25kms/he to meet the Reg here in Australia all 3 gears are almost exactly the same speed.
hi, it can be determined by the battery voltage to what percentage the scooter is charged. I don't want to charge it to one hundred percent all the time. I want to charge up to approx. 80%, thanks for the advice.
Hi. So I just got the mantis 8 and got it set up. I charged it and my screen is flickering. I tried to get into the settings but the screen just flickers and then Cuts out. Now the light is on the display but I can’t see anything. Is the switch bad?
I had the same problem. Looks like changing brightness (Pc) is a bad idea, but it could have been a coincidence. It started at 3 (max), at 2 it dimmed, and at 1 it flickered and died. Can't get it to run to change it. Maybe need to reflash or something? But with what, I'm not sure.
@@zbret I got it fixed. It’s a bad screen. I sent kaabo a video on what’s going on. They sent a new screen out. But with their slow time in communication. I just bought another. It fixed the situation.
@@Airbornealltheway88 Thanks! I actually just posted a vid of this at v=8Q5qebzvZbE, and was considering getting a new screen, but they sell them for $60 on their site and my scooter is 1 day old. I can find similar looking displays but not the same model name as the Kaabo. Kabbo uses LT-01, but there are TF-100, QS-S4, etc and they are usually cheaper. Plus most ship from China and take 2-3 weeks to arrive which I'd rather get them faster. How long did they take to reply? I wound up posting a comment on their page at v=zSzxYfhKePo Note if confused about the "v" codes, they are for videos, just put it in after the "watch" in the browser to see them. YT comments block links.
@@Airbornealltheway88i literally have the same issue and emailed them I’ve had the scooter two days there sending me a new display seems like a common issue
@@johnhammel6277 it took forever too. I ordered one off another website. But it took like 3 week’s coming from kaabo. Now I got 2 just in case. I don’t think I’ll be ordering another kaabo. I put 200 miles on it so far and not to happy about it. Still a fun scooter but the stem is starting to get loose no matter how tight I put it. The rear turn signal is out. The tires suck when they start to get low. So stay away from rocks. I take really good care of this scooter too.
Unfortunately there is no way to save the password. I know what you mean it gets annoying having to keep entering it I. And it times out rather quickly but there’s no way around it, you will need to enter the password each time.
Hey, do you know why my scooter drops battery when driving it shows full charge but when going past 25km the battery drops to 1 bar than goes back up when slowing down
Hello. It could be a few possibilities. 1. the eco/throttle switch is broken. 2. the controller: If you replaced a controller, there could be a speed limiter. 3. If the battery voltage is reading low, it could be that there is not enough battery power to get you up to the high speed. Hope this helps.
Any ideal why a wolf warrior x is showing 55mph on the display. It's there while it's idle and when riding. Everything seems to work otherwise and the P-settings are correct. It's set to bump start and it does need a bump before it will accelerate.
hello sorry if I disturb, I have recently purchased a kirin G1 and in the P 03 program section I cannot understand what this parameter is for and what to set, let's say that I am quite inexperienced in this regard, and I would not want to ruin the scooter. Can you help me please? Many thanks in advance. My kirin is 52v can you give me a hint?
My display stopped working today (LT-01) on a Wolf Warrior 11. It was fine and then I turned it off for 5 minutes back on and display won't turn on now. Any tips? :/
Hi i got the 2021 modell and i have a error code that popping up E-10 and then i shut off the scooter and the error disapears and comes back again after maby 15min. Do you know what this is ? :S
I recently had this E10 error as well on my 2021 mantis 10 v2, everything worked fine except speed readout. I swapped the display and so far so good, error no more..
Hello. I opened the display to clean it but after I assemble it turns it on but does not accelerate when I press the trigger. Do you know what could have happened?
hi there im thinking og buying the wol warrior x pro+ to your website and does it come with hybrid off road tires only?coz i want some street tires too!is the X pro+ was the improve version of the pro coz i watch some review about the rear fender grinding the rear tires too!
We also sell, CST 10" x 3.0 Street Tires that would work. Here is the link: epiccycles.ca/product/spare-parts/bikeparts/scooter-tire-tubes/mantis-3-0-street-tire/ If you want us to swap them out for you we can for an additional $120 labor fee. If you want to keep the original off-road tires the cost of of the street tires will be $65 each otherwise we can just do a stragiht swap if we keep them and you only pay for the labor fee.
Io ho questo computer qs-s4 e monto una batteria Lg 72v 32ah monopattino zero11x P03 - Voltage level of machine 72 giusto ? e P15 - Controller cutoff voltage?
Hi there I have the mantis eighthe mantis 8 and I have the LT01 is 01 displaying. I have the error code E 10 Everything works fantastic all the lights everything however. The display where it shows miles per hour when you hit the throttle it doesn't show miles per hour but the scooter does work fantastic Do you have an idea what might be wrong with that if if I need a new display how would I change out the display
Hello.E10 error means communication issue between display unit and controller. There are three things that can go wrong: display throttle, wire connecting the display throttle and controller and controller. You can play with the wire by moving around and see if the error goes away, the most common cause is the display throttle which needs to be replaced.
Hey, having this issue that my speedomoter isnt showing the correct speed...shows more than it actually is.. Can it be the case that if my maximum speed is set to etc 70% and while it goes 25km/h it still shows 37 km/h on my speedomoter. Or what might be the case? Every setting is correct.
Typically it's always 1500 since 2022. i would reach out to the retailer you purchased it from and ask them, otherwise you can contact Kaabo and provide them with the serial number. They should be able to track it down based on that.
I have the mantis 8. This morning I turned on my scooter And it turned on. However I tried to kick start the scooter it would not go anywhere. I have a new controller throttle controller. It does turn on but there's no power it won't go anywhere any ideas
With this kind of symptom, the brake sensors are needed to be checked by unplugging left and right cables (located under the brake levers) and try to throttle it to see if it fix the problem or not. If the problem persists, please send us an email to info@epiccycles.ca
You may have a defective display but could also be something else not functioning. Best to bring it into a local shop that sells this type of scooter and has extra parts to trouble shoot and diagnose the problem for you.
Hello i am just riding my kaabo wolf warrior 11 and i turn it off and turn it on later it shows 18902km in it while i only have like 610km , it just dropped instantly
Thank you so much, I searched for this and found the old password which obviously didn't work and was sooo disappointed I wanted to return it and go for a refund. I have the Mantis 10 v2 and it is now a delight to ride....once again well done, please keep up with your answer to the nanny states.
Glad we could help!
Is there a way to reset to factory settings?
Nope
Best video I found. THANK YOU!!
It's such a pleasure to see a good ,informative video which yours is, thank you
Any idea how I can setup the LT01 to have different speeds in the 3 gears.
At max or above 70(P9) I can see a difference but if I set it lower while trying to get gear 1 to max out at 25kms/he to meet the Reg here in Australia all 3 gears are almost exactly the same speed.
Hello, this is possible - you would have to bring it in to your local scooter shop for a mechanic to do for you.
@@epiccycles9 many thanks. I’ll call the dealer tomorrow.
@@epiccycles9 thanks. I’ve just taken it to the dealer I bought it from. He says there’s nothing he can do other than change P9.
Any thoughts?
Thank you for the password to the settings!!! Very helpful video 😊
Thank you so much. I just bought it and all clear.❤
hi, it can be determined by the battery voltage to what percentage the scooter is charged. I don't want to charge it to one hundred percent all the time. I want to charge up to approx. 80%, thanks for the advice.
65v would be about 80 percent
67.2 is 100percent. 54v is dead
Great video man!!! Helped out a lot!! Thanks man. I just got the warrior x.
Is this display visible in sunlight? I read somewhere it's difficult to read it clearly in sunlight.
Hola para una batería de 60v a qué voltaje debería estar
En el parámetro p1?
Hi. So I just got the mantis 8 and got it set up. I charged it and my screen is flickering. I tried to get into the settings but the screen just flickers and then Cuts out. Now the light is on the display but I can’t see anything. Is the switch bad?
I had the same problem. Looks like changing brightness (Pc) is a bad idea, but it could have been a coincidence. It started at 3 (max), at 2 it dimmed, and at 1 it flickered and died. Can't get it to run to change it. Maybe need to reflash or something? But with what, I'm not sure.
@@zbret I got it fixed. It’s a bad screen. I sent kaabo a video on what’s going on. They sent a new screen out. But with their slow time in communication. I just bought another. It fixed the situation.
@@Airbornealltheway88 Thanks! I actually just posted a vid of this at v=8Q5qebzvZbE, and was considering getting a new screen, but they sell them for $60 on their site and my scooter is 1 day old. I can find similar looking displays but not the same model name as the Kaabo. Kabbo uses LT-01, but there are TF-100, QS-S4, etc and they are usually cheaper. Plus most ship from China and take 2-3 weeks to arrive which I'd rather get them faster. How long did they take to reply? I wound up posting a comment on their page at v=zSzxYfhKePo
Note if confused about the "v" codes, they are for videos, just put it in after the "watch" in the browser to see them. YT comments block links.
@@Airbornealltheway88i literally have the same issue and emailed them I’ve had the scooter two days there sending me a new display seems like a common issue
@@johnhammel6277 it took forever too. I ordered one off another website. But it took like 3 week’s coming from kaabo. Now I got 2 just in case. I don’t think I’ll be ordering another kaabo. I put 200 miles on it so far and not to happy about it. Still a fun scooter but the stem is starting to get loose no matter how tight I put it. The rear turn signal is out. The tires suck when they start to get low. So stay away from rocks. I take really good care of this scooter too.
Can I adjust P3? Isnt this to adjust your top speed??
How do you save the password? I have to keep entering the password everytime i want to change the settings. Your help is much appreciated, thanks.
Unfortunately there is no way to save the password. I know what you mean it gets annoying having to keep entering it I. And it times out rather quickly but there’s no way around it, you will need to enter the password each time.
Hey, do you know why my scooter drops battery when driving it shows full charge but when going past 25km the battery drops to 1 bar than goes back up when slowing down
How can I reset the PA, since I want the mileage to start from zero after my complete maintenance of the scooter
My kaabo wolf warrior pro 10 will only go 20mph any advice
Hello. It could be a few possibilities. 1. the eco/throttle switch is broken. 2. the controller: If you replaced a controller, there could be a speed limiter. 3. If the battery voltage is reading low, it could be that there is not enough battery power to get you up to the high speed. Hope this helps.
Thanks alot but watched it several times and still don't understand what's the CH feature?
Muchas Gracias muy bien explicado, Lo Máximo 💪
What should the Kaabo Skywalker 10 c setting be for p2
Any ideal why a wolf warrior x is showing 55mph on the display. It's there while it's idle and when riding. Everything seems to work otherwise and the P-settings are correct. It's set to bump start and it does need a bump before it will accelerate.
It’s possible there might be a problem with the display or controller. We would advise to bring it in to your local shop to troubleshoot both issues.
@@epiccycles9I was able to change a p-setting and then change it back to what it was. This fixed it. Odd error.
hello sorry if I disturb, I have recently purchased a kirin G1 and in the P 03 program section I cannot understand what this parameter is for and what to set, let's say that I am quite inexperienced in this regard, and I would not want to ruin the scooter. Can you help me please? Many thanks in advance. My kirin is 52v can you give me a hint?
P3 is speed selection setting. Usually set by the facotry to 0. Do not make any changes to this setting.
My display stopped working today (LT-01) on a Wolf Warrior 11. It was fine and then I turned it off for 5 minutes back on and display won't turn on now. Any tips? :/
Check the connectors between the display and controller, sometimes the wire gets tugged or pulled on and it gets loose.
@@epiccycles9 I already did it wasn't that. Could it be inside the scooter if I open it up?
Hi i got the 2021 modell and i have a error code that popping up E-10 and then i shut off the scooter and the error disapears and comes back again after maby 15min. Do you know what this is ? :S
E-10 error code usually represents there is a problem with your controller. You will proably need to replace the controller to eliminate this error.
I recently had this E10 error as well on my 2021 mantis 10 v2, everything worked fine except speed readout. I swapped the display and so far so good, error no more..
I changed the brake settings and the error have not been up since that
Hello. I opened the display to clean it but after I assemble it turns it on but does not accelerate when I press the trigger. Do you know what could have happened?
Hello, first check to see if all your wires are connected securely and properly.
Maybe lost the little magnet on the back of the throttle lever?
I bought a LT01 thumb throttle from ALi but it doesn't turn on. I am using it on my Kaabo Wolf Warrior 11.
hi there im thinking og buying the wol warrior x pro+ to your website and does it come with hybrid off road tires only?coz i want some street tires too!is the X pro+ was the improve version of the pro coz i watch some review about the rear fender grinding the rear tires too!
We also sell, CST 10" x 3.0 Street Tires that would work. Here is the link: epiccycles.ca/product/spare-parts/bikeparts/scooter-tire-tubes/mantis-3-0-street-tire/
If you want us to swap them out for you we can for an additional $120 labor fee. If you want to keep the original off-road tires the cost of of the street tires will be $65 each otherwise we can just do a stragiht swap if we keep them and you only pay for the labor fee.
What about 36v?
Good day Sir, same on kaabo Skywalker 8H?
Hello, we do not carry that model of scooter to confirm. Please refer to the Skywalker 8H owners manual.
Io ho questo computer qs-s4 e monto una batteria Lg 72v 32ah monopattino zero11x P03 - Voltage level of machine 72 giusto ? e P15 - Controller cutoff voltage?
P7 is wrong, it should be 0= soft 1=stronger acceleration
only on 2022 model, they also have cruise control
Hello i changed the PC to 2 and i cant see nothing. The scooter is working but the screen is not , how can i fix it
Hello, please give your local scooter repair shop a call to further discuss.
Mine shows low battery even when full any fix ?
i think it’s normal
Hi there I have the mantis eighthe mantis 8 and I have the LT01 is 01 displaying. I have the error code E 10 Everything works fantastic all the lights everything however. The display where it shows miles per hour when you hit the throttle it doesn't show miles per hour but the scooter does work fantastic Do you have an idea what might be wrong with that if if I need a new display how would I change out the display
Hello.E10 error means communication issue between display unit and controller. There are three things that can go wrong: display throttle, wire connecting the display throttle and controller and controller. You can play with the wire by moving around and see if the error goes away, the most common cause is the display throttle which needs to be replaced.
Its the little magnet on the back of the throttle I glued it in better
How can i modify de battery voltage?
Hello, You can change the battery voltage on your display. Please refer to your product manual for more detailed instructions.
Hey, having this issue that my speedomoter isnt showing the correct speed...shows more than it actually is.. Can it be the case that if my maximum speed is set to etc 70% and while it goes 25km/h it still shows 37 km/h on my speedomoter. Or what might be the case? Every setting is correct.
Your tire size setting in P0 is likely incorrect. Probablly set at a smaller size than it actually is.
Is there any way to change the code to enter the p settings?
Hi Amund. You cannot change the code to enter in the P settings. This is hard coded by the factory.
Thank you. Wery helpfull
Glad it helped!
I just brought a wolf warrior x plus 2023 and I've tried 1500 and 9221 and neither of them work why is that
Typically it's always 1500 since 2022. i would reach out to the retailer you purchased it from and ask them, otherwise you can contact Kaabo and provide them with the serial number. They should be able to track it down based on that.
I have the mantis 8. This morning I turned on my scooter And it turned on. However I tried to kick start the scooter it would not go anywhere. I have a new controller throttle controller. It does turn on but there's no power it won't go anywhere any ideas
With this kind of symptom, the brake sensors are needed to be checked by unplugging left and right cables (located under the brake levers) and try to throttle it to see if it fix the problem or not. If the problem persists, please send us an email to info@epiccycles.ca
@Epic Cycles thank u for your reply I will do that..very helpful
@Epic Cycles would u kindly send a pic of the left and right cables need to be unplugged
@@bplynch834 You're very welcome! Fingers crossed this fixes your scooter.
@@bplynch834 Unfortunately I can not upload a photo here. But you can place your hand on the brake and trace the wire back to the connection.
I also have the E-10 error but everything works. Only the front light doesn't come on out of nowhere, but the horn works. I have a v2 10 plus
I have the same issue but everything works fine but the display the miles per hour doesn't do anything it's it just reads Error code E10
E10 how repair.
When it’s powered on and you hold down “mode,” a blue headlight icon is displayed. What does this mean?
I noticed it also
Hello. If the scooter had a headlight, it would mean the headlight is activated.
perfect, thx for infomation about voltages
Thank you!
sabes como hacer factory reset en zero 10x?
Hello, we do not have this model. Please refer to your owners manual, or contact the company you purchased it from.
What if I don’t have any power on display
You may have a defective display but could also be something else not functioning. Best to bring it into a local shop that sells this type of scooter and has extra parts to trouble shoot and diagnose the problem for you.
When I try change p7 it won’t go past 1
Yeah because it’s either 0 or 1
Can you remove the code? And how to factory reset P settings?
Unfortunatley there is no way to remove the code nor is there a factory reset for P Settings. We wish there was a way as well : )
@@epiccycles9 (QS-S4) Hi,where can I get my code, the seller did not say when buying?
@@УколвВАТУ 1500 or 9221
Hello i am just riding my kaabo wolf warrior 11 and i turn it off and turn it on later it shows 18902km in it while i only have like 610km , it just dropped instantly
Hello. Did you purchase your scooter used? We would suggest bringing it into your local e-scooter repair shop to have it assessed.
Can I put a QS-S4 display on a wolf warrior x base model?
Yes, either the Qs-S4 for LT-01 will work on a Wolf Warrior X base model (not mini motors system)
Nice
THX
Wolf warrior x unlocking
ua-cam.com/video/sfmZ4y_IDXQ/v-deo.htmlsi=Z8rX7QKBUK1Oi8AA
My computer on bordo qs-s4
Yes, this is simalr to the one showns in this video
Its crazy that Barry Nisan doesn't work at Nissan I mean c'mon man they'd surely give you a job just because of your name wouldn't they 😂
Бля Рахмет еле нашел хэлп к этому курку