Installing Key Ignition to ZERO and Inokim E-Scooters
Вставка
- Опубліковано 28 лис 2018
- This video tutorial shows you how to install the key ignition / key lock for the ZERO or Inokim electric scooter. This applies to ZERO 8, 9, 10 and Inokim Quick and Light models.
You will require a wire stripper, thin strips of heat shrink to secure the thin wires and one thick strip of heat shrink.
To purchase a key lock for your ZERO or Inokim e-scooter, please visit www.falconpev.com.sg - Авто та транспорт
Please read this before trying to do it by yourself !
1. DISCONNECT the battery before starting to cut, disconnecting, or solder cables, this is the first and most important thing to remember !!!
2. For your safety, I advise you to NOT do this inside your home/apartment because of the risk of fire (lithium batteries pack a serious amount of energy and in case it exploded you won't be able to stop it by yourself, in case it begins just run and hope that the insurance will cover that...
and I also want to share my thoughts and experience with installing a key ignition, all other videos that I found about it were talking about replacing the key ignition or going for the wiring at the bottom where the controller and battery are located, In my opining this is not safe to do so and I liked more this method where you do the wiring+soldering on the top where is the display is located. it feels much safer and easier to do because the scooter brands and built might be slightly different and in my case the was a special grouping wiring that includes the connectors of the brakes input, lights and horn buttons, and the display so when you are checking the down part of the scooter it might be hard to recognize which wires are relevant only for the display so by doing it at the top is much easier and safe (yes it won't look very aesthetic because you will probably need to tape it with electric type or heat shrink tube)
Oò8ooiiì
Hello. Can you tell me please if i can install ignition key on a bluetran lightning like in this video ? Thanks.
hello all, i bought the key ignition / key lock from you and i installed it on my weped gt. the installation was so easy to do. thanks for the vid
victor benjamin let us know how we can help
So can this replace the ON / OFF switch in some scenarios?
Hi may i know why i cant on the trottler but 5the key sweith can be on.. I follow all the step. Pls advise pls
Is the stock key Ignition water resistante on the zero 10x? or should I replace it with a motorcycle one?
so i have this but without key lock. i rigged it up seemlingly like you did but all i get is it stay at 47 volts never moves. even with just a black and red wire would i connect the red to the green of lcd?
at the moment its black to black red to red spliced into exsisting lcd wire
Hello! I just got this for my zero 9, but... the exta wire wrap isn’t included. Where to find it? Thanks!
hi all,, there was a part that look like the video was Cut, is that why you need to reverse the connectors ?
May I know if this can be install on ninebot es2? Thanks
Hello! I am more than intrested to buy this for my zero 9, but it does not have the same lcd: mine is qss4. Is it different?
Any idea what I need to conect the ignition to on the kugoo g2 pro
Thank you so much.Im gonna do this to mine
Where did you buy the part from please ?
Can you show how to convert an scooter's electric brake (thumb control) into a brake lever?
is the red one connected directly to battery? because i have different color for the wires. Please help
My question to you please im trying install a video back and front camera video recorder which wire on the throttle small display monitor is the acc wire to cut the camera off and on with the display monitor please 🙏
Dope very simple and easy
How to wire a new Ergonomic throttle on this lcd display throttle?
can i install this to kingsong n1-b?
Can I install this on a fiido with wuxing throttle
Boss falcon, can i do the same procedures to dualtron scooter?will it work?
Nice video.. can you tell me how to change fuse on my zero10? It just turned off suddenly thank you!
Great video, may I ask for your help? I have a zero8 with the qs-s4 lcd display. I had a crash and the wires that goes into the lcd had been pulled out. I dont have a diagram how to solder them back inside ,was wondering if you could take a picture of the inside of a qs-s4 lcd for me? Thanks alot
Hey please email sales@falconpev.com.sg for better support or whatsapp us at +65 8748 4565
hi sir , where can i buy key ingnition? thank u
What about g2 booster? The same operations?
But does the scooter only work when you start it with the key
Is lcd wire the same thing as throttle wire
Will it work with Inokim OX model ?
Hiya I have got one 1200watt Electric Scooter dual motor very fast but the problem is no control Speed just comes with moves handle like motorcycle handle So I can’t never control the speed and it’s very dangerous to drive without Speed control So how I can Replace or fix new 3 gears by finger Speed (Note ) I can send you photos for the Scooter please thanks
Excellent Video!!!! Dear Sir if u could do one demo on installing Wuxing?
I connected it to the red line, but the key turns off, but the monitor stays on. Please tell me how to deal with it.
Will this work on my fiido q1s? If that so, what will be the use of my remote ignition starter? Thank you.
dave carlo gabrillo if you have a remote you don’t need this
Hello thanks for the video. I have the ZERO 8 in 360 watts and 36 V. Is it possible to put a motor 500 watts and 48V. Thanks in advanced
Its possible but why would u do it the battery alone is 420€ and the motor 200€ just buy the scooter and sell your old one
will this work for a super73 rx?
Can you do it on the ninebot es2
Do the keys fit for all ignition locks of the same model? I lost one of the keys that came with my Zero 10x and would like spare keys. Thanks
No you would have to change the whole lock
The tightening screw was rusty on my "supposedly" new 10x scooter, is that normal or maybe used?
A Viking has to be used for sure
Hello friends, maybe can you make a video that shows how to connect an alarm to a scooter? Thanks
do I need to connect all the black wires together? (all three conttected to each other)
as i saw the video, i think they do connect all the 3 black wires but still i need confirmation from them. also, what happen to the cutted red wires from the scooter (not from the lcd), as they have connected to the key ignition wires.
Greetings from Colombia
I installed the voltmeter with a key, I did the steps that you say in the video, the one I installed is a Zero 8 electric skateboard, but when installing it the voltmeter flashes and does not indicate the volts, apart from the board of the skateboard indicates error e10, I appreciate your help to solve this problem
This won’t work on zero 8 use white wire instead of red
So you just twisted the wires... No soldering? Should've soldered.. makes for a better connection
yes we do solder. Just for the purposes of this video we did not.
falta su tutorial para cambiar llanta de rueda trasera del zero 8
Thank for the video. Is the key unit water resistant/proof?
Lol
Thanks you so much. As what I needed.
Is it possible to connect the wires together to keep the scooter ON or does the lock ignitiom provides something else.
The whole point of this is to make a safe switch with a key so no one can just grab your ebike or escooter and ride away with it by just turning it on.
if you wish to disable only the motor but keep the display and lights on, then you will need to look for other solutions or talk with someone with the relevant knowledge.
Can the key be removed while in the on position? I have my keys attached to my belt and do not want to detach them each time.
On the videos I've watched, zeroes come with an ignition key as standard?
Zero 10X and 11 I think. My Zero 10 did not.
@@FlowerPowerNZ I've has Mt zero 10X almost a month. 360km on the clock so far. It has 1200w front and rear, it's a beast.
Everyone wants to talk to me about it which can be annoying but it's curiosity I guess, hopefully I time tgeir will be hundreds of them on the roads.
Comment from Japan. There is no ZERO video in Japan, so it will be very helpful. Is the wiring connection of ZERO8 and ZERO9 the same? Thank you
the wiring for the keylock is the same for 99% of electric scooters
Robert Schrauder ?
It is possible to connect Single / Dual
Switch in the same way?
Hector Quintero yes you can connect a rotary switch for single and dual.
@@FalconpevSg Thanks for your answer
Does this Ignition Key works with Kaabo Mantis with Minimotors display/controller?
TheChazas what’s mantis?
Hi Chazas! In the case of Kaabo Mantis Dual (2020) the ground is black and you have to use the white cable, not the red.
Only with the white and the black cable which comes from the controller works for me.
Hey where did you get that Ignition Key Switch or the name to buy it for my scooter ???
Marcuzzi jacuzzi you can buy it from here: www.falconpev.com.sg/collections/newest-products/products/handlebar-mounted-voltmeter?variant=44972468245
Ok thanx
hi. where can i unplug the connectors to avoid the sparks?
Muhd Nazir battery compartment
thanks! figured it out
do you have a photo of how the wiring should be?
same question here
Is it just the same way of connecting to Jh-100 throttle?
Jh-01 rather.
Hi falcon. I try to install key ignition on my zero10, but its not compatible.
Earl Laguni it should be compatible. Maybe you are not doing it correctly.
@@FalconpevSg 2 times we try to install with my zero10 and to my frend wirh zero8 but its not compatible.
Will this work with swagtron eb5 pro plus electric bike?
Adam Stone yes it should.
How do I disconnect the battery?
Just make sure you close the scootter or power off it. Its fine
I installed it on my Apollo City and the ignition does not work. The scooter turns on bu the keyed ignition has no effect. When turned off I get E10 error but the scooter sill functions. @falcon Pev any thoughts?
What’s the Apollo city? You bought it from us?
@@IronRabbit_19 it’s fine on the zero 9. Where did you get the immobilizer from?
@@FalconpevSg I got it from RevRides USA which should be compatible with Zero 9. is there any setting in the LCD 'P" programming?
@@IronRabbit_19 send us a pic of your wiring...sales@falconpev.com.sg
I have the same problem with zero 10
I have green purple brown red black from display and red green black from key voltage wire I have a super 73 e bike how would I wire it
The safer way is to do it from the controller.
@@FalconpevSg how would I do that?
@@FalconpevSg how would I do that
I followed your instructions but i didn't cut off the connector but i did the work after it. And it didn't work. The scooter work normally but the key not. What can be the problem?
you might have missed a step and it is crucial to follow just to be sure :)
@@FalconpevSg your instructions are not clear enough. Didn't work on my zero 9
Where we can buy the key ignition switch on internet or online ?
sorry, you can order here: www.falconpev.com.sg/products/handlebar-mounted-voltmeter
would it void the warranty if we do this?
Joef Clarin not if it is done by the official distributor
@@FalconpevSg what about after market installation?
I live in Italy and I would upgrade my Zero 8 with some parts I've seen on your website, how can I do that without voiding the warranty?
Where do I get that red clamp? Very cool
Hi Jay. Found it: www.amazon.com/VGEBY-Handlebar-Extender-Extension-Aluminum/dp/B079BSDXTW/ref=sr_1_82?dchild=1&keywords=red+tube+clamp+for+scooter&qid=1602233807&sr=8-82
Can this be installed on the emove touring?
Lee Andrada almost any escooter
My zero 9 needs to be cut and connected to the white wire. Then connect the black wire with the black of the LCD. It's worked.
Can i install it on a apollo explore scooter ?
You can install it for any scooter
You leave the battery connected to the scooter while doing this right ?
No it’s better to disconnect the battery and drain out any remaining charge
how can a fix the speed limit for my zero 8?
Travel In go to P08 and set to 60 to limit the speed to 25kmh
@@FalconpevSg thanks I did it well 👍🏻👍🏻
Can I also do this to Fiido Q1?
Genevie Dominguez yes you can
How do u take off the rubber handles u guys never show that
Twist it off and if that doesn’t work, use water
Hi, can I do the same for the kugoo m4? Also, how secure is it? Are the keys the same across all these locks?
Keys are different. Yes it will work for kugoo too but your need to know how to solder
This wiring diagram can be applied to the xiaomi m365?
Qogicx nope
@@FalconpevSg thank you for the fast response, if i applied this method it will show the 5v of the dashboard not the voltage of the battery is that correct?
Qogicx hi it doesn’t affect the display of the lcd at all. Your lcd will still read the main battery voltage
@@Qogicx hi, did you manage to solve the meter reading the 5v only?
@@jim3808 i decided only hook up the key switch without the voltmeter because my e-scooter slowed down with it.
Do one for inokim quick 3 ?
I Installed it on a quick 3 super, working as expected
Can u mod this ignition on a gas scooter?
Not possible
@@FalconpevSg what if buy a ignition USB port then connect this key ignition will it work on gas
Cool ink...!!!!
Can I install this on a dualtron?
JustNeL yes it can.
do not work with my 0-8 i can always start it witout key, voltmetere show 00.0 and she tell me E10
now it's work, it was not red wire, but white for me. i've cut 1 by 1 wire to look who have juice! and that's all
@Lenanea thank you. It was the same on my Zero 9. Voltmeter dimly showing 0.00 and pulsing. I was still able to turn on the scooter with the key in the off position and it showed E10. After reading your post, I checked the white wire with a multimeter and it had 54 volts. Once I hooked up to the white wire, all working correctly.
Hello, since you are promoting this, I have the same one. It's new. It works, but when I install it, it walks a few meters and disconnects the electricity from it. I can't turn it on again unless I put it on the charger for a second
Your battery is dead
@@FalconpevSg The battery is completely new
@@FalconpevSg When I lift it on the ground it works normally but when I ride it only walks a few meters
@@majdalaghawani1791 your motor and controller connection has something wrong
Can you also show how to install on the handle bar? including how to remove the handlebar grips. :)
No
I'm not looking forward to this...I crashed and the key ignition is completely broken. Now I have to replace it and I'm not really handy with anything electrical or with scooters...
Is it the same for M365/pro ?
Wondering the same thing 🤔
@@Greg-vg1pt I figured how to put one on M365 & M365 Pro
@@dawoodkhan6067 how? 😊
@@Greg-vg1pt I am currently selling the diagram to do it. If you contact me privately we could discuss further.
@@dawoodkhan6067 LOL! No thankyou
where to buy it?
search for "ZERO LCD" or "key lock" on our website here www.falconpev.com.sg. Thank you!
don't work unless my ignition keys broke it was from ebay…..not sure if its my switch but green and red with the key to the on works any other wire example red and black i get nothing with a continutity test on a multi meter
red black nothing
green and black nothing
green and red working
thats all I followed the video and mines not working
I wish they would make these with proper connectors that fork so you could connect them straight from the controller to LCD connector inside the deck, instead of having to cut and solder wires, would make it much more consumer friendly.
thanks for the feedback
For quickvolt 8 the right wire is white, not red
ok thanks for the advice
is the old power button still work when you long press to turn on? :) if yes. then this key is nonsense
Seems to be nonsense.
You can only cut the red and black wire
twist and heatshrink huh? i know where not to take my equipment. lol.
I just don't understand why all wires had to be cut.
I would never install something like this without soldering the wires first.
But why cut it when you can open up the display and solder directly to the pcb!
These type of lcd displays usually have an extra unused entry place for such a wire.
I would NOT recommend going with this solution
Any key operated device with wires is installing a mechanism to connect wires together. Anybody wishing to hack the system just has to snip the cable and touch bare wire cores together to bypass the "security"
You can hack almost any lock, but better than no security at all.
@@FalconpevSg True but the best door locks and padlocks do not permit simple bypass operations
I Ken faid my key of my skoter
This is a completely bodged job. Should have taken the time to do this properly. You only needed to cut the RED and the Black , why cut all of them when you had to reconnect them??
Robert Schrauder what? Please explain
I can’t even follow along because the angle is too zoomed in and we cannot even tell what wires are being connected to what wires from which source. Gahhh
2nd
он просто тупо скрутки что ли делает? паяльником не лучше разве?
Hello. Can you tell me please if i can install ignition key on a bluetran lightning like in this video ? Thanks.
What’s that? Bluetran
I connected it to the red line, but the key turns off, but the monitor stays on. Please tell me how to deal with it.
change from red to white. it's worked for my zero 9.