1963 Impala SS Convertible Part 12 Quarter Panel Install Repair, Prep, P O R 15 DIY Auto Restoration

SHOP INFORMATION :
Contact us at : [e-mail]
Our Address is: Guzzi Fabrication
3206 Main St Suite 106
Rowlett Tx 75088
www.facebook.c...
Honesty - Quality - Craftsmanship

[@mcy1122]

This man is fearless! Between the last video and this one, he basically remanufactured half the car -and then it turns out great!🙌🏾

[@guzzifabrication3448]

I'm gearing up to get the quarters installed and finish out the rear half. Thanks for watching !

[@ST-cy6we]

I remember that the wheel housings for the convert were different. Can't wait to see that fix

[@guzzifabrication3448]

Part 9 Thanks for watching !

[@rwendell0912]

Excellent looking quarters,car is going to look great when your done. Keep up the good work,really like following this build.

[@guzzifabrication3448]

Thank you for supporting the channel !

[@mrpurcountry]

Turning out really nice, your attention to detail and going the extra mile is so important.

[@guzzifabrication3448]

Trying to keep craftsmanship alive. Thanks for watching !

[@samuelsmith2522]

They really screwed that car up! Can't wait to see the finished product ❤

[@guzzifabrication3448]

I will make it like new ! Thanks for watching !

[@ChristopherL0rtiz]

Man. I know your customers have confidence driving down the road, washing their cars, knowing you have addressed, prepped and treated every square inch. Was that a dynacorn or aftermarket passenger quarter? Looked thinner then the original quarters do.
Great work bro 🙏

[@guzzifabrication3448]

That quarter panel came from classic industries, honestly all of the replacement panels are about the same gauge.....Thanks for your support and watching !

[@ChristopherL0rtiz]

@@guzzifabrication3448 I meant the quarters you removed. Looked funky

[@guzzifabrication3448]

I got it brother, it's the original, someone had cut in a patch panel from another Impala, really rough work.....
@@ChristopherL0rtiz

[@62_impala_ss]

Great work!! I put POR 15 on my wheel buses too.. great stuff still holding up

[@guzzifabrication3448]

Yes Sir !

[@rorymerke6659]

I must be missing something? is POR 15 not a 3 part process?@@guzzifabrication3448

[@miltoncostakis799]

Thanks Robert! Great work!

[@guzzifabrication3448]

Thanks Milton !

[@deltabloo]

Thanks for sharing, I’m learning a lot!

[@guzzifabrication3448]

Thanks for watching !

[@ST-cy6we]

Click "like", then watch the video

[@guzzifabrication3448]

Thank you Sir !!!

[@johnkelly6942]

Another quality repair.

[@guzzifabrication3448]

Thank you Sir !

[@ChristerJohansson-ic5be]

Great work

[@guzzifabrication3448]

Thank you Mr. Johansson !

[@jeremyolson2596]

NICE!

[@guzzifabrication3448]

Thanks brother !

[@DA-cg3du]

👌

[@4speed3pedals]

You are correct about that flat chisel you have. I did find a Steck Super SeamBuster and it is a hand held flat bar with a sharpened edge on one side and the opposite side has a pneumatic arbor that fits into an air chisel. Looks cumbersome and if you have to support the area momentarily, both hands are busy, one on the splitter and one on the air chisel. I agree with your method of splitting the weld versus drilling a hole all the way through.

[@guzzifabrication3448]

Thank you Sir !

[@petar443]

Hey Robert how did you address this mess - 6:30 i never saw on the videos and i watched them all. I mean the inner rocker/lower b piller?

[@guzzifabrication3448]

I didn't get all of the video repair on that one I'll do an in-depth inner rocker on the next one or you can go back through the 64 or 62 Impala builds I know I have it there

[@maxilgoi]

I guess the rust encapsulator not is better than antioxidant products for full restoration

[@jaymavrick7433]

Nice !!😁

[@guzzifabrication3448]

Thanks !

[@josedelao9124]

Good luck with all the warpage LOL

[@guzzifabrication3448]

What are you stupid? I'm executing the repair not you....no need to worry. I have plenty of metal finishing repair videos on UA-cam.