Chris, thanks for taking the time to create this video...while I don't own a Zino I'm sure this video could be incredibly valuable to those who do own one and who might need to take on this task. Question: For brushless motors are there symptoms that one might see that would indicate the motor and/or ESC is about to fail? And if so what would those symptoms be? Or do they just tend to be catastrophic failures with no warning signs? Obviously if they fail in flight I'm assuming that the drone would just fall out of the sky...what has your experience been?
Jet Martin Never have seen a warning sign personally nor have I had one or the other just fail in flight. I’ve seen stuff from people I have helped but those esc signs usually won’t let you fly or tell you your very stupid if you do try. 😂 Usually a crash causes the failure. Most common I have seen anyhow.
Hey I see you have a lot of information on the Zino.. my 18 month old zino no longer can connect to the transmitter and says USB disconnected every time. Any tips or a link that may help me before I run it over with my truck in frustration?? thanks!
At that age if it just started doing it then it is likely the main board. I repair drones and a lot of Zino’s. Sometimes it is a board that can be repaired and sometimes it just needs replaced. Don’t run it over please! 😂
Hey QC Guy, you helped me out on calibrating my gimbal and fixing me up with the program to do it with and I want to thank you for that. Gimbals working perfect now. Now I have a new problem hopefully you might have an answer to. My battery must have popped out while i had it about 350 feet up and it came crashing down, relatively slowly at least. When i picked it up everything was intact but both the motors on one side wont spin. Lights come on and the rear one is really hot. If one ESC on one motor, will that affect the other motor on that same side or are both ESC's probably bad or am i dealing with a problem further in the quad? Its a Hubsan Zino Pro Plus by the way. Thanks again.
Ok. I can tell that one ESC looks fried. Looks burnt and gets real hot. If the output voltage is off, does that mean I’d probably need a new main board?
@@QCGUY Ok. Thats much cheaper than the main board at least. Do you know what the voltage should be going the ESC's from the power board. Hopefully this is the last question! LOL! Thanks again
Chris,Thanks for the video. I have replaced the back(B) motor. Before flight , i have tested w/o Propellers installed. I checked the motors by my hand , I noticed all three motors spins Clockwise , but the front(B) motor spins CCW. Is this normal behaviour?
No that’s a problem... Sounds like you have reversed the red and black wires on the motor you replaced. Have a look at this... www.dronezon.com/learn-about-drones-quadcopters/how-a-quadcopter-works-with-propellers-and-motors-direction-design-explained/
Hello. My one motor is spinning in the opposite direction. which cable did I solder wrong? Red with black? Yellow is always in middle? Thank you so much :)
Hey QC... I crashed my H117s. Rear passenger motor does not spin at all but has 12V at pins A-C to on the ESC... Can I assume a motor alone would fix this, how would you handle this?... Secondly, I am getting a "gimbal sensor abnormal" error in red on the app and the gimbal does not operate up and down, video recording and the image is good.... How would you handle this???? Much thanks. Want to save this drone if I can. Just got it a week ago and unfortunately have spoiled my experience by crashing it :(
My rule of thumb is parts are cheap and replace both motor and esc while you’re in there anyhow. If you go into the settings of the app under the gimbal tab it should give you a code if there is a issue. If it says 2000 I can tell you it needs the gimbal cable replaced for sure.
Muhammad Firdaus First it’s a piece of electronics that gets pretty hot and can simply just fail but normally it’s something like a crash that puts resistance on that motor and causes that ESC to burnout. My rule of thumb is if a motor fails or a ESC fails just replace both while you’re in there.
hi, i have a motor stopped because a crash. I check the ESC and motor but i don't see anything broken or something similar. The problem of these components are visible? or just stop working
It appears as if the motor on my Zino Pro is bound up after an upside down crash on pavement. I'm pretty sure its physical problem with the motor. It is stiff in rotation. Should I also change the ESC while I'm into it? And please send me the parts if you have spare lol
I flew my zino 2 after the crashed few days before, then suddenly my zino 2 felt from 100 m alt while flying. Now the front right motor only spin abit everytime I start, kind of stuck, rotate abit then stop again. How do you define the ESC is broken or not, all the LED light on the ESC are working perfectly except the front right motor. Can the LED light on if the ESC is burnt ?
The led can still light if the esc is burnt. If you don’t feel anything when turning the motor by hand it’s likely to be the esc. I personally replace both when in question 👍
Money Mitch I can sell you a arm with the motor and esc already installed and ready but you will still need to solder the wires to the power board but it’s way easier soldering wise for sure.
Hi Chris, my zino crashed down hitting a tree and fell on a pavement(very unlucky😅) This caused the 2 ribbons connecting on both sides of gimbal snap,now no feed,binds and even wifi signal. My question is does the 2 broken ribbons are somewhat intergrated with wifi connections or maybe theres another issue with its mainboard? It stills boot up completely. I hope u can help me as im planning to order replacement on broken ribbons..thanks and have a good one!
Jayson Ricaplaza without the cable you won’t have any wifi or connection what so ever. 👍 Sorry to hear of your crash but at least now these parts are available.
@@QCGUY i hope flex is the only problem.many thanks Chris i really appreciate knowing that theres a big chance to revive my zino.btw,do you have any tutorial for flex installation on zino gimbal?
Robby RC UAV I wouldn’t say I know in great detail but thank you for the kind compliment. I just know how to fix stuff is all. Some could tell you every bit and peace of the components but all I can do is tell you it’s broke and needs replaced. 😂 Thanks again 🙏
Hello Friend. Man I really need your help let me tell you my story: I received my Drone Zino yesterday, I called and the red light is blinking I have been searching a lot and it seems that it is not releasing the signal from the wi-fi and it really is not because on the cell phone no appears my phone can detect 5g. I can connect the cell phone to the control normally only that the cell phone doesn’t show the Zino network there ... I saw several videos talking about this problem and they all indicate that it’s a problem in the flat only that the Drone came in brand new I just opened it and even did a boxing I just can't link here but UA-cam and block that comment for you. have any idea what you can do because the Drone as I said came zero new just took it out of the box and called it is ok the cute app turned on the phone and already gave this problem right away and I who will stabilize normal ... Thanks I await response
CANAL LELOTREM Usually it’s something to do with the camera cable but sometimes the micro sd slot isn’t connected to the board correctly or came loose and this effects the connection as well. It could be something totally different but that’s all I can tell you right now. Join my group for further support. facebook.com/groups/HubsanQC/?ref=share
Thank you so much. I did that once (just the motor part ok)... but now I had to open it and "pass" the cable w esc to the short arm... When i try to turn it on blue lights are on for 2 secs (w the relative noise) but then itgoes off.... I opened it again i found and fixed 1 of the 4 cables of esc... but still goes off. Both red lights dont go on... could u consult where to focus?...or an email to contact you:)
Antigoni Kotsoni It sounds like a wire or wires are still not right. I don’t know what you’re problem was prior or if damages were more widespread so it’s hard to tell you anything without that and not having it in front of me on my bench it’s equally hard. There’s not a one answer suggestion or fix in this case unfortunately. Sorry 😐
Hi sir is that the procedure to test propeller motors i have zino pro and looking for tutorials. I want to test the motors without take off for my zino pro
How good would it be if you could set different settings for expert mode and normal mode. So have the gimbal speed and aircraft speed set low for better filming. Then for expert mode have them set high for taking pictures etc....
Hi again QC Guy:) I have been trying to find a decal kit for the Zino with no luck. I have emailed them at Hubsan for some kind of schematic of the plastic sizes as I would like to personalise my drone and Controller. What do you think? I have looked on line and there is loads for the Mavic etc:( I have only seen one on UA-cam that as been wrapped in a 5d Carbon and it looks quite nice. Any ideas yourself as I know you like to tincker with them. hehe. I dont have mine yet but would like to know for all the cut outs etc.
STOP RIGHT THERE! LOL You will get nothing from Hubsan which I will bet my life on and if they do reply it will be asking for videos and pictures and mass confusion. I might add pin stripes but I don't do any skins or anything like that. Sorry
good night. I couldn't remove the esc and the wires that connect it by the arm. is very difficult. I thought about leaving the wires and just changing the esc, but I'm afraid it was the wires that burned the esc
Salvador Ochoa I do but I won’t be back in town till next week. I sell the whole arms complete with everything. Motor, ESC, antenna and covers. You can contact me if you still need one. Thanks facebook.com/qcguy.wade
Chris, wow look at those hands! 🤣😂 But seriously, this is a great video to have! Really documents this process! Hope I won't have to re-watch this video anytime soon, but I can't tell you how many of yours I have already had to re-watch for help. This looks like a pain in the butt! Great to see you back!
Hello, I am Korean. Your video gives me a lot of strength. In this video, I saw the WIFI of a ZINO drone connected to your cell phone. I tried to connect, but I couldn't because I didn't know the password. I want to know how to enter the password when connecting to WIFI. PS : There may be a wrong sentence by writing it with a translator. ^^::
I find the best way to remove solder is with a "solder wick". It's basically just a ribbon of braided copper that soaks it all up when heated - very easy. Just search for "solder wick".
Hello Chris. Firstly, thanks for the fantastic video, as everyone states here "great job!" Do you have a link on your site where I can buy an arm (left front)? Had my Zino for a couple weeks and hit a tree, groan. I see Geekbuying.com, but they show 30 days for delivery (out of China). Please reply if you get time. Cheers, Ronald
You have to pry the lamp shade off with a little more force on the rear legs. Pry the opposite end of the screw and it will come off. Like I said it requires more force but it will come off.
Waleed Muniri My charities are for children battling things like cancer so I’m sorry but you’re requested donation for school books came across as a scam to me at first. Now that I know it’s not may I suggest you try prioritizing your priorities? Sell your ZINO or other material items and buy your books 👍
HELLO QC GUY !!! I wish I had watched the application of LOCTITE 242. I want to know the correct way to use LOCTITE on Zino. Could you please demonstrate?
Guy this video will save me. Now I can change my esc by following this video of yours.
Srt Nay Glad to hear it 👍
Hi Chris,
Excellent tutorial. Does this apply to the ZinoPro?
Yes 👍🏻
Thanks!
Chris, thanks for taking the time to create this video...while I don't own a Zino I'm sure this video could be incredibly valuable to those who do own one and who might need to take on this task. Question: For brushless motors are there symptoms that one might see that would indicate the motor and/or ESC is about to fail? And if so what would those symptoms be? Or do they just tend to be catastrophic failures with no warning signs? Obviously if they fail in flight I'm assuming that the drone would just fall out of the sky...what has your experience been?
Jet Martin Never have seen a warning sign personally nor have I had one or the other just fail in flight.
I’ve seen stuff from people I have helped but those esc signs usually won’t let you fly or tell you your very stupid if you do try. 😂
Usually a crash causes the failure. Most common I have seen anyhow.
@@QCGUY Thanks!
All your video really help me repair my zino pro.
Glad to hear that 🧡
Chris, is there a way to check motor health by adjustable power supply . If we apply Voltage Black and Red or Black and Yellow will the motor spin?
You need a special meter to test them. I think you can find information if you search for something like test brushless drones or rc motors. 👍🏻
Hey I see you have a lot of information on the Zino.. my 18 month old zino no longer can connect to the transmitter and says USB disconnected every time. Any tips or a link that may help me before I run it over with my truck in frustration?? thanks!
At that age if it just started doing it then it is likely the main board. I repair drones and a lot of Zino’s. Sometimes it is a board that can be repaired and sometimes it just needs replaced.
Don’t run it over please! 😂
Hey QC Guy, you helped me out on calibrating my gimbal and fixing me up with the program to do it with and I want to thank you for that. Gimbals working perfect now. Now I have a new problem hopefully you might have an answer to. My battery must have popped out while i had it about 350 feet up and it came crashing down, relatively slowly at least. When i picked it up everything was intact but both the motors on one side wont spin. Lights come on and the rear one is really hot. If one ESC on one motor, will that affect the other motor on that same side or are both ESC's probably bad or am i dealing with a problem further in the quad? Its a Hubsan Zino Pro Plus by the way. Thanks again.
One esc won’t effect the others so it sounds like you need to check voltage out on your power supply board that feeds esc and lights.
Ok. I can tell that one ESC looks fried. Looks burnt and gets real hot. If the output voltage is off, does that mean I’d probably need a new main board?
And thank you very much for your reply.
@@johnkatter2373 a new power supply board most likely not the main board.
@@QCGUY Ok. Thats much cheaper than the main board at least. Do you know what the voltage should be going the ESC's from the power board. Hopefully this is the last question! LOL! Thanks again
Hello, is the rear engine removal the same way? No screws to open under the rear engine, how to open it. Thank you.
Thanks I found it in the continuation of the video. Good expression. Thank you so much.
Chris,Thanks for the video. I have replaced the back(B) motor. Before flight , i have tested w/o Propellers installed. I checked the motors by my hand , I noticed all three motors spins Clockwise , but the front(B) motor spins CCW. Is this normal behaviour?
No that’s a problem...
Sounds like you have reversed the red and black wires on the motor you replaced.
Have a look at this... www.dronezon.com/learn-about-drones-quadcopters/how-a-quadcopter-works-with-propellers-and-motors-direction-design-explained/
Yes, You are right , i have confused about the red and black wires and looked at the next motor that is wired reverse. Thanks again.
Hello. My one motor is spinning in the opposite direction. which cable did I solder wrong? Red with black? Yellow is always in middle? Thank you so much :)
Hey QC... I crashed my H117s. Rear passenger motor does not spin at all but has 12V at pins A-C to on the ESC... Can I assume a motor alone would fix this, how would you handle this?...
Secondly, I am getting a "gimbal sensor abnormal" error in red on the app and the gimbal does not operate up and down, video recording and the image is good.... How would you handle this???? Much thanks. Want to save this drone if I can. Just got it a week ago and unfortunately have spoiled my experience by crashing it :(
My rule of thumb is parts are cheap and replace both motor and esc while you’re in there anyhow.
If you go into the settings of the app under the gimbal tab it should give you a code if there is a issue.
If it says 2000 I can tell you it needs the gimbal cable replaced for sure.
Thanks Chris for doing the tutorial ,but I will leave this one to the likes of yourself and other experience people.
Ste Procter Hope most wont need to bother needing this information. 👍
On what factors that esc and motor is broken? Is it because of too hot or dust?
Muhammad Firdaus First it’s a piece of electronics that gets pretty hot and can simply just fail but normally it’s something like a crash that puts resistance on that motor and causes that ESC to burnout.
My rule of thumb is if a motor fails or a ESC fails just replace both while you’re in there.
hi, i have a motor stopped because a crash. I check the ESC and motor but i don't see anything broken or something similar. The problem of these components are visible? or just stop working
You most likely have a bad ESC but just be smart and replace the motor and ESC because the shafts on the Zino motors bend easily.
It appears as if the motor on my Zino Pro is bound up after an upside down crash on pavement. I'm pretty sure its physical problem with the motor. It is stiff in rotation. Should I also change the ESC while I'm into it? And please send me the parts if you have spare lol
Tommy Guns Dunleavy I can sell you a perfectly working complete arm with motor and esc already to go. Message me....
facebook.com/qcguy.wade
I flew my zino 2 after the crashed few days before, then suddenly my zino 2 felt from 100 m alt while flying.
Now the front right motor only spin abit everytime I start, kind of stuck, rotate abit then stop again. How do you define the ESC is broken or not, all the LED light on the ESC are working perfectly except the front right motor. Can the LED light on if the ESC is burnt ?
The led can still light if the esc is burnt. If you don’t feel anything when turning the motor by hand it’s likely to be the esc. I personally replace both when in question 👍
Is there anyway of changing the rear motor without soldering?
Money Mitch I can sell you a arm with the motor and esc already installed and ready but you will still need to solder the wires to the power board but it’s way easier soldering wise for sure.
@@QCGUY I've bought a soldering iron because you made it look too easy but I'm not sure what I'm doing lol
Hi Chris, my zino crashed down hitting a tree and fell on a pavement(very unlucky😅) This caused the 2 ribbons connecting on both sides of gimbal snap,now no feed,binds and even wifi signal. My question is does the 2 broken ribbons are somewhat intergrated with wifi connections or maybe theres another issue with its mainboard? It stills boot up completely. I hope u can help me as im planning to order replacement on broken ribbons..thanks and have a good one!
Jayson Ricaplaza without the cable you won’t have any wifi or connection what so ever. 👍
Sorry to hear of your crash but at least now these parts are available.
@@QCGUY i hope flex is the only problem.many thanks Chris i really appreciate knowing that theres a big chance to revive my zino.btw,do you have any tutorial for flex installation on zino gimbal?
Jayson Ricaplaza I’m going to have one up in the next few days. 👍
@@QCGUY great! I look forward to that.cheers mate
Great video... like this kind of videos where people know in detail what they are talking about ;). Thank u for sharing your experience on this.
Robby RC UAV I wouldn’t say I know in great detail but thank you for the kind compliment. I just know how to fix stuff is all. Some could tell you every bit and peace of the components but all I can do is tell you it’s broke and needs replaced. 😂 Thanks again 🙏
Hello Friend. Man I really need your help let me tell you my story: I received my Drone Zino yesterday, I called and the red light is blinking I have been searching a lot and it seems that it is not releasing the signal from the wi-fi and it really is not because on the cell phone no appears my phone can detect 5g. I can connect the cell phone to the control normally only that the cell phone doesn’t show the Zino network there ... I saw several videos talking about this problem and they all indicate that it’s a problem in the flat only that the Drone came in brand new I just opened it and even did a boxing I just can't link here but UA-cam and block that comment for you. have any idea what you can do because the Drone as I said came zero new just took it out of the box and called it is ok the cute app turned on the phone and already gave this problem right away and I who will stabilize normal ... Thanks I await response
CANAL LELOTREM Usually it’s something to do with the camera cable but sometimes the micro sd slot isn’t connected to the board correctly or came loose and this effects the connection as well. It could be something totally different but that’s all I can tell you right now.
Join my group for further support.
facebook.com/groups/HubsanQC/?ref=share
Of course the arm would be the hardest to replace since i need to replace one. (Front, A) could you do one?
I don't see any problem with me doing one. I don't want to but if I had to it wouldn't be bad.
Thank you so much. I did that once (just the motor part ok)... but now I had to open it and "pass" the cable w esc to the short arm... When i try to turn it on blue lights are on for 2 secs (w the relative noise) but then itgoes off.... I opened it again i found and fixed 1 of the 4 cables of esc... but still goes off. Both red lights dont go on... could u consult where to focus?...or an email to contact you:)
Antigoni Kotsoni It sounds like a wire or wires are still not right. I don’t know what you’re problem was prior or if damages were more widespread so it’s hard to tell you anything without that and not having it in front of me on my bench it’s equally hard. There’s not a one answer suggestion or fix in this case unfortunately. Sorry 😐
@@QCGUY ty foryour time... ty for your videos:)
Hi there, i try to repair the esc's and motores, but something GOES wrong! When e putt the batery, the zino turns on. Do you know about that? Thanks
facebook.com/groups/HubsanQC/
Hi sir is that the procedure to test propeller motors i have zino pro and looking for tutorials. I want to test the motors without take off for my zino pro
Kratos GOW I don’t have anything myself. I just fly them. These motors last a long time.
Very handy tutorial I'll watch it in full later.. Did the motors die in good old hubsan fashion? Or you just taking it apart yo show people?
MarcRCAddict Just for the tutorial. All good 👍
@@QCGUY hi mate, ah that's good then, happy flying 👍
How good would it be if you could set different settings for expert mode and normal mode. So have the gimbal speed and aircraft speed set low for better filming. Then for expert mode have them set high for taking pictures etc....
John young Pretty good I guess but that might fall into the shit💩in one hand and wish in the other and see which you get first category. 😂
Another great video! That was thorough and concise! Thank you for taking the time to share this with us!
Hello, did you make a video to show how to change one arm on the Zino?
Is it necessary to make a welding to change one arm?
Tatou2B No video but I will. Yes you need to solder the wires.
@@QCGUY ok, thanks. It would be nice you show us soon.
Tatou2B I recently lost my mom so soon might not be as fast as you would like.
@@QCGUY of course, i understand. thanks for all the help you give yet to the community.
Hello Chris, to be clear, your motor hasn't gone bad all ready, this is just a tutorial on how to do it, right? Mike in N.C
Mike Kinney
Nothing failed.....just several people requesting it so I went ahead and did it.
@@QCGUY Thanks Chris, because I just added the zino to my fleet, it came today.
Mike Kinney Enjoy 😉
Is there a place that does these kind of repairs for those of us not talented enough to do it our self have zino and one motor gone
Charles Baker I do them if you’re in the US. I get on average 1 Zino a week here lately.
@@QCGUY how do Iget a hold of you to send it to you
Charles Baker You can message me on Facebook under QC Guy. That’s preferred 👍
Do you have a video on how to replace a leg on HABSAN ZINO PRO?
Pavel Pogorelov Im posting one 👍
Hi again QC Guy:) I have been trying to find a decal kit for the Zino with no luck. I have emailed them at Hubsan for some kind of schematic of the plastic sizes as I would like to personalise my drone and Controller. What do you think? I have looked on line and there is loads for the Mavic etc:( I have only seen one on UA-cam that as been wrapped in a 5d Carbon and it looks quite nice. Any ideas yourself as I know you like to tincker with them. hehe. I dont have mine yet but would like to know for all the cut outs etc.
STOP RIGHT THERE! LOL
You will get nothing from Hubsan which I will bet my life on and if they do reply it will be asking for videos and pictures and mass confusion. I might add pin stripes but I don't do any skins or anything like that. Sorry
do u get real gopro quality on the moniter ?
You get good quality. The quality of a budget drone but better then some in its class.
can u pls give the name of the parts u r using
@@jvlogs7917 it’s s motor and esc replacement so it’s a motor and esc.
good night. I couldn't remove the esc and the wires that connect it by the arm. is very difficult. I thought about leaving the wires and just changing the esc, but I'm afraid it was the wires that burned the esc
Srt Nay Check continuity on wires and cross check them for shorts.
Keep it up. You are our go to guy when it comes to the zino
My front arm b motor got damage wen i crashed it it wont come on do u sell parts
Salvador Ochoa I do but I won’t be back in town till next week. I sell the whole arms complete with everything. Motor, ESC, antenna and covers. You can contact me if you still need one. Thanks
facebook.com/qcguy.wade
@@QCGUY dnt have face book u got insta gram
Salvador Ochoa email me.... qcguy.chris@gmail.com
Chris, wow look at those hands! 🤣😂 But seriously, this is a great video to have! Really documents this process! Hope I won't have to re-watch this video anytime soon, but I can't tell you how many of yours I have already had to re-watch for help. This looks like a pain in the butt! Great to see you back!
I don't want to change esc i can do right?
Waleed Muniri Sure 👍
You don’t have to if you are sure it’s only your motor that is bad.
Can I use Hubsan Zino H117s motor to replace the Hubsan Zino Pro motor?
Jonathan Moses Yes, they are the same part number. At least they were in the beginning when I first looked. Thanks
Thank you for your information! I just replaced one of my zino pro motor and it worked!
Hello, I am Korean. Your video gives me a lot of strength. In this video, I saw the WIFI of a ZINO drone connected to your cell phone. I tried to connect, but I couldn't because I didn't know the password. I want to know how to enter the password when connecting to WIFI.
PS : There may be a wrong sentence by writing it with a translator. ^^::
It’s 12345678
I find the best way to remove solder is with a "solder wick". It's basically just a ribbon of braided copper that soaks it all up when heated - very easy. Just search for "solder wick".
dipsyfriday I use those at work. 👍
I have a few different tools for this.
Thanks for the video QC. In my Zino, the red motor wire comes last. Did anyone else notice this or could it be that mirror effect with selfie cameras?
There two combinations or directions the red in black wires go. Yellow is always the same though.
How much for zino 2 plus back right motor
Sorry I don’t have any to sell right now.
Nice one mate its its a pane in the but on upare one plus don 🤠🇬🇧👌👌👌👍
Good job! Thanks for sharing your knowledge for us diy'ers
Wow! What an opening!
Greg Traver I’m fond of it as well. 😊
Hello Chris. Firstly, thanks for the fantastic video, as everyone states here "great job!" Do you have a link on your site where I can buy an arm (left front)? Had my Zino for a couple weeks and hit a tree, groan. I see Geekbuying.com, but they show 30 days for delivery (out of China). Please reply if you get time. Cheers, Ronald
RonaldNexus email me kitchwade@gmail.com
How to binding new remote for zino ?
go to the remote tab in the app, hit refresh and connect to the hubsan I.D. in the list.
@@QCGUY thank you sir.. its work..
Wonderful!
Good job!! Thanks!
Anyone find a suitable bolt-on motor upgrade? If not, anything else? I don't mind doing custom mods.
Not worth it to me to dabble in that with this quad but good question I hope someone answers for you.
@@QCGUY - I tinker and invent. I'll get back to you.
I am unable to open rear motors please guide me
You have to pry the lamp shade off with a little more force on the rear legs. Pry the opposite end of the screw and it will come off. Like I said it requires more force but it will come off.
Thank you! And i asked for some donations for my studies any update?
Waleed Muniri
My charities are for children battling things like cancer so I’m sorry but you’re requested donation for school books came across as a scam to me at first.
Now that I know it’s not may I suggest you try prioritizing your priorities?
Sell your ZINO or other material items and buy your books 👍
@@QCGUY my Zino has crashed it doesn't have resell value
@@waleedmuniri2138 I guess it's time for you to do a go fund me then. Good luck on both your zino and school. Take care!
HELLO QC GUY !!!
I wish I had watched the application of LOCTITE 242. I want to know the correct way to use LOCTITE on Zino. Could you please demonstrate?
Rodrigo Rascher
Here...this guy speaks my language and explains it for you. 😂
ua-cam.com/video/gCE5WfoMxM8/v-deo.html