He probly meant no harm but !!When he gets to 3:30 he mentions to jump start the car to raise the voltage when no maintainer available ( a BATTERY MANTEINER IS NEEDED, a 15 to 25amp unit 20USD TO 50USD is more than enough to raise voltage, I used a 15amp unit for complete update). If u jump the car for programing, either u r going to burn the junction module or ur ecu/pcm/dme (if ur car battery is healthly plus jumping from another car with a healthy battery plus the altenator current frm the other car !!it will create an overcharge and burn modules). I FOLLOWED HIS ADVISE PROGRAMMING WHILE JUMPING AND MY JUNCTION MODULE BURNT WHILE PROGRAMMING MY BMW v6 328I. SINCE MY MAIN ECU/PCM/DME LOSS POWER WHILE PROGRAMMING IT DIED. !!I HAD TO BUY ANOTHER JUCTION MODULE FRM EBAY(2 JUNCTIONS THE FIRST THEY SENT WAS FAULTY) HAD TO BUY AOTHER ECU/DME/PCM EBAY AND IGNITION KEY WITH CONTROL AND A FOOTHWELL MODULE LINKED TO THE ECU FROM SAME EBAY SELLER (THE FOOTHWELL MODULE CONTAINS INMOBILISER DATA) AND 30USD BATTERY MANTINER TO PROPERLY PROGAM MY BMW AND GET IT RUNNING. He should have at least mention that when jumping from another car that the other car has to be engine off, and even so not sure if it wud work that way...….bmws and any vehicle 2005 and up should not b jumpstart frm another engine on car (risk of burn module), proper way to jump is with a cheap 30usd to 90usd lithium jumper or equivalent, or jump frm another car engine off at risk (on older vihicles it was ok to jump start from another engine on car cos the batteries were usually completely drain( probli owner left lights on) newer cars dont ever completely drain cos auto lights off or auto shutting electrical when volts low)..the only time ill risk jumping from another car with their engine on is if I was driving a v8 or larger v6 and they were driving a small v4..if it was the other way aroung me drivng v4 they driving v6 v8 I would only jump if their engine was off
Hi I feel really sorry for what happened to you... Watching my own video now, I realized I said jump the car... when what I meant was connect the maintainer... I use a 30 amp charger/maintainer... You can indeed program (not BMW really... due to the higher voltage required...), jumping from another battery/car, but both engines off... I did it few times before I bought my maintainer.... Once again... sorry...😔
@@LMAutoRepairs its ok..ill sue utibe not u...its good that we share info to help each other out...like u I also self-taught my self to use the tablet.
Gretings from Puerto Rico!It's been a while since I wrote you, but I always share your videos on my workshop page.Excellent video mate! Just a little detail, you forgot to show how to connect the MaxiSys via internet and the car connections. Just for those, who dont know how to do it and recently buy a MaxiSys Elite or Pro.
this machine has all the programming and encoding modules the same as the ista esys etc program to encode tabs quadrants NBT screens thank you for your help
@@LMAutoRepairs thank you my friend I appreciate your availability and thank you for helping me because I'm buying a machine like this expensive and complicated😅
@BK-it6te Again, depends... If you just require general code reading etc... any low-mid range will do, the likes of Autel, Topdon, Launch... If you require more in depth then you have other tools for that... Or, if you need it just for a brand then other tools apply... You are not saying what you actually want it for, so it is difficult to say...
@derkdevries328 Yes... but, the immobiliser side of things will not be changed... So, keys will have to be programmed separately and not with this tool, as it not capable of that... 👍👍👍
@@LMAutoRepairs thanks LM. Im508 should be able to prgram key again..if i also have that right? I see people going thru lots of bench set soldering etc on the cas which is connected to the cas. Wonder why take all the headache if you could just do it through the obd port? Afterall your wifi server support for bmw as you mentioned is kind of in your ms908
Hi I do have a battery maintainer now... bought a good one in the mean time... It is a 30amp, used it loads of times after, and seems to work ok. 👍👍 Thank you for watching!
@@gunti80 Hi I got this one... www.halfords.com/webapp/wcs/stores/servlet/ProductMobileDisplay?catalogId=10151&langId=-1&categoryId=255205&productId=1078771&storeId=10001
@@cambam2430 sorry sir dint mean to sound rude....puck bmw they lie and trick people so much..example the crank sesor the way they route the wiring overtime the sensor wiring gets loosed causing problems..the manual states that the sensor has to b removed from top when it can b removed frm the bottom really quick after throwing in the garbage all the plastic on the bottom and the little plate with unusual retainers that prevent ur hand frm fitting thru the bottom and rerouting and connecting the harness to the sensor.....I also threw in the garbage the bmw plastic thing that cover the coils and make it longer when testing and removing anything under that area.
This was just a demonstration... The programming can be beneficial is has been released new versions to correct small problems... A bit like updates... But you need specific tools to do such thing... Thank you for watching! 👍👍👍
Thank you for your response would I need to buy the autel package that comes with programming tool or can I go with standard package just to maintenance like brakes and oil changes and smaller issues?
I tried to the same thing as you but I don't get the same options as you and also I cannot even program a key its for a 2003 BMW X5 e53. is there a problem on my maxicom or is the car to old
@@marcusb9365 Programming... check under retrofit... If is not there, check cheat coding... If not there, add +NAUX to the VO/SA/FA and code the car or the affected modules... Tank you for watching!
Hi I give you an example... My 7 series, had for a long time a fault with one of the airbag modules... would come up with something like internal failure... Clear the the codes, would last for days, sometimes weeks and even months.... Has been doing it for 2 years... I was too lazy to reprogram it... But finally done it around Christmas last year... no issues ever since... This is just an example... the manufacturer sometimes releases updates to rectify or improve deliverability etc... Thank you for watching!
i know you posted this question 5 years ago.... but if you or anyone else happens to read this..... ALWAYS remember that if you do not know the answer to a question you may have, yet you want to know the answer to said question to benefit or learn from it because you genuinely want the answer, then no matter what anyone says.... there's no such thing as a dumb question in that instance!
The shift solenoids. I asked transmission shop for an estimate to replace the solenoids and they told me they couldn't do it cause they had to be key coded and they didn't have that capability. They might be wrong.
Seeing an Error when trying to get a module programmed. Any advice or help? Error States: Connected vehicle has an unknown data status. It is not possible to handle this one with diagnostic tool. Ensure that the latest version of diagnostic tool has been loaded or contact after-sales department. When the measures plan was calculated a field appeared. Possible Fault Cause: Integration level (S15A-20-03-524) is incorrect or too new. Any ideas here?
It does... but don't think it does on the newer models, that do it on the idrive... At least I have never tried it... Thank you for watching and for your comment!
@@LMAutoRepairs no it wasn't running, but update stoped and I tried to start it, no start now🤔I think might've wiped the ecu...thanks for getting back to me.. I did it wrong and down a mini diesel file I think form autel,when going into ecu for engine it says it's diesel but it's petrol😑
The jbox is the interface that enables the communication between the car and the tool... Being a J2534, is also compatible with flashing capabilities and the option to be used with some OEM softwares... 👍👍👍
Yes you can... But... the gearbox might be coded to the immobiliser... Maxisys does not do it... IM608 does it... The reason that lead me to buy it, was actually to do it on a F10... Thank you for watching!
I have the Autel MS908SPRO and I know it does programming because I have the J box with it. I wanted to know if if could be used to program a new CAS module and key for BMW 530I or will I have to send the module out for programming?
@@LMAutoRepairs ok thanks and I'm going to program a new CAS I purchased but wanted to know if the keys needed to be programmed before or after the CAS?
hello friend, my car currently running with a ecm frm a used donor bmw, got everithing program...my question is, using the 908 do u know if its possible to erase the vin frm a donor ecm and so only the vin frm my veicle poping up wen doing emissions test...they dont want to give me the little plate sticker unless I fix thar issue....usually wen I connect the autel it will ask me to choose my vin n the donor ecm vin
When you flash/update the module, using the Maxisys, if you "tell" her the modules have been replaced, it will update the vin during programming... I have a video on my old e65, changing the Airbag gateway, and i show just that... Hope it makes sense... Thank you for watching!
so when i plug my scanner all in with jbox and go into programing and coding it runs the scan through all modules but only gives me 2 options after coding and car/key memory what am i doing wrong please help
I have a 2001 Volvo s40. Can this device activate fog lights for the vehicle? My car did not come originally with fog lights but the plugs was there and I connected to oem fog lights.
Hello, I also recommend Elite, because I am also using this product and the experience is not bad. This is a video of me using Elite to perform online programming for the Transmission module of Audi A4L: ua-cam.com/video/ulewXsAKls4/v-deo.html , share it with you here, you can refer to it. A video of the function performed for the BMW is also in my shooting schedule! If you are interested, you can click to take a look, or give me your opinion. There are more videos on my homepage of using different devices to do different functions of the car. You are welcome to follow me and I will be happy to answer your questions. thanks.
Here in the UK you can't... Will just fail to download the software... Check out with Autel if you leave elsewhere... As someone was saying that in the USA you can still programming...🤷♂️ Thank you for watching and for your comment.
u can as long as u also buy the keyfob and cas module that belongs to the ecu.....the only issue wud be that if u live in a state with extremely strict smog rules it might not pass....6/16/2020 I was instructed by a star smog tech to get in contact with state referi to fix my issue wer my car has ecu ftm other car../////6/11/202 usually when I coonect the scanner to my car that has ecu frm another car it will ask me to choose between my vin and the vin of the car that the ecu came frm....tried smoging prior and the tech said som bulls..t story that his computer cudent connect to my car.....im asuming if u buy a brand ecu ter wudent b that issue....I cant affor new ecu so if noone wants to pass my car, ima just paint the sticker with glitter nail polish to corresponding year color, n use a gps jammer so my car does popup as a red dot on cops map screen...but ten they might b wondering why my car not showing up in teir screen since its modern car or tey might not even notice epecially in city with alot of vehicles...probly I wud only get caugh if I get pulled over and cant provide up to date regristion papers.
LM Auto Repairs I guess what I mean is, if you have this, do you need ISTA? Like do they do the same thing? It seems this is better obviously as it does all makes and is portable. Downloading ISTA seems like a job in itself.
@@Chris-rs3dj Not really... with this tool, you don't really need ISTA... the only thing with ISTA, is the wiring diagrams, testing components etc... that obviously this tool does not have... 👍👍👍
Hi thanks for the info. I see it has a retrofit and conversion tab, I have swapped my gearbox for a 6 speed from a 5 speed and retrofitted cruise but cruise only works up to 5th gear and when I change to 6th gear the cluster display only displays up to 5th gear and goes blank in 6th will this do this? Many thanks
LM Auto Repairs Great video!!! can you reprogram/coding the cruise control, mine its not working for some reason and I would like to have it back, Thank you!!
Hi If was working and it stopped, is probably nothing to do with coding or programming... Most likely there is a fault somewhere inhibiting the cruise control.. Scan the car and look at some live data to find out what's happening... Hope that helps. Thank you for watching!
Programming usually refers to the writing of the module software... also knows flashing... Obviously Programming can refer to other software updates etc... Coding refers to the changing of settings/parameters, in this case to match the car's options etc... 👍👍👍
I tried programming my new headlights to my 2017 bmw 330i, it required Ethernet connection, I kept running into connection issues. In the autel diagram I have to use the special adapter that has both Ethernet cable connection and OBD port, and then it says to poking Ethernet cable into the autel MS908P. Can I just use a personal hotspot that can connect to the connector and tablet via Ethernet ?
Yes... you need the ethernet adapter for the F series and above... It is not expensive... I believe on the new 908 that adaptor come with it... not on the old ones... I got my one from Autel directly... It is something worth to have... I never tried any workaround, so not sure if it is possible to do it in any other way... I would say no... As the autel needs to connect to the car through the ethernet to the car... Thank you for watching and for your comment!
@@LMAutoRepairs I have the Ethernet adapter and everything I’m just not sure on how to connect it, if I can’t have WiFi on how is the autel supposed to download the file needed for the programming? Do you know how to set up the Ethernet on the device ? I tried and still can’t figure it out
😊 The Autel will automatically switch between the ethernet which will be connected to the car, and the Wireless when it needs to download files... Don't need to worry about that...😉
@@LMAutoRepairs so To clarify, I can use the personal hotspot on my iphone to connect to the autel to the internet, and then once the Ethernet is connected to both the OBD and the autel, it will switch between automatically? Because I tried that and then i was getting a “no vehicle communication” pop up on the autel
Hi guys very good video , I have a Autel 908 but dont have the pass through tool j..... can I purchas add this to my 908... I presume i will need my subscription updated to Autel. Thanks Autel is awsome
I believe you can... You need the j3524 and the subscription updates... but confirm it with Autel themselves... Just to make sure... Thank you for watching and for your comment!
Hello, can you CODE Auxiliary to a 2004 bmw 530i on Maxitool so it can show on the display screen ? It only shows FM/AM/CD I installed auxiliary but it won't show on screen and I read it needs coding but most videos I've seen are done on INPA but I have Autel Elite scanner. Thanks
Not INPA... you can't code with INPA... Is with NCS Expert... Again, autel will do it by modifying the VO... Just add +NAUX to the vo, save it and the code the ccc and all the relevant modules... Quite straight forward...
@@LMAutoRepairs does VO means vehicle operations ? Not sure what you mean exactly by VO and CCC Sorry I'm not finding the right way to do it 😭 Do you mind sharing the steps ? Truly appreciate your time
VO=Veichle Order CCC=Car Communication Computer There is step by step guides out there... I am sure... I don't remember now from the top of my head, and if you need a step by step guide, I don't want to give you inaccurate information...
Never used that tool... Not sure if the solenoids need to be coded... Or are you talking about the whole mechatronics? Thank you for watching and for your comment!
Dear friend I see yr video when u did the mart car updates the software for transmission and u said u have A CD for it can you please let me know where i can find it
I have a 2012 bmw 528i where it stalls out in the middle of traffic when I step on it what can the problem be? Where can I buy this to program the ekps for it I bought one plugged and played but it would not run
@@LMAutoRepairs el Mismo aparato the same thing you have or anything else that's a bit less pricey bmw Is charging me 4000 to change the ekps and install a new fuel pump
@@LMAutoRepairs it throws code p0087 but goes away if I go to step on the gas hard to pass it feels like a thud then the engine just shuts off if you try to give it gas while rolling the computer on screen says fuel supply drive moderately I have to pull over to shoulder as fast as I can and then the engine shuts up if you try to turn it on again immediately it just cranks but will not start after about 20 to 12 mins later while car is off completely the car will just turn back on like normal and I can keep driving it does it randomly BMW charged me 200 to tell me it's the fuel pump that needs replacing and the ekps module, they are trying to charge me 4000 for parts and labor.
@@Luis92r I would take it to some good independent garage... I believe that that model has 2 fuel pumps... A low pressure one in the tank, and the high pressure one under the bonnet... It can be any of the two failing... The one under the bonnet, the high pressure, don't think it requires any programming... so if BMW is telling you that, means the other pump... 4k for that, seems a bit exaggerated to me... Hope that helps...
@@LMAutoRepairs thanks for your quick reply. Did you ever try to to program out the passenger seat occupation sensor with autel? I know it fails a lot of times in the bmw, I know that you can do it with ncexpert, but I'm interested about autel capabilities. Because I just ordered one.
@@modestasserpenskas2353 Never did one i think... i mean, not with the autel... but under cheat coding might be possible... Just go through the options available... 👍👍👍
Can you please help me with a question, what about the subscription? How does the Maxisys know meaning if i go onto Benz and pay for say a 2 day sub, how does it know my MaxiSys belongs to that sub?
@@LMAutoRepairs who do you pay 1 year too Autel of Benz? My autel I purchased June 6, 2018 and my free updates end June 6, 2020. . I read that my 2 year updated include the BMW and Benz subscription to program these cars. Meaning i don't need a separate sub for the BMW or Benz website to access the programming service is that correct?
Hey buddy GREAT VID. Just a question. Can I use Maxisys or Autel to code replacement EKPM3 module that came from a different car but comparable? My car is an E82 2.0D 2008 & the part came from a 2008 E87 2.0D. Please let me know. Thank you buddy.
No worries. Keep up the good work. I was more wondering if I can use Autel to tell the EKPM3 that it’s now in a similar model but different car so it has correct flow values etc. If so can you point me in the right direction menu-wise that would be greatly appreciated? Thank you again.
The Autel is quite intuitive on that sort of stuff... Watch this video... ua-cam.com/video/pAKztvmr07g/v-deo.html The principle is the same... Once you flash the module with the software for the car, to change VIN number etc... and you code it... the module becomes part of the car... As if was fitted from factory...😊
yes it can it works with all or nearly all brands....and only bmw and Mercedes need programming for the rest only coding is needed....only bmw and Mercedes required this more expensive tablet....for all other brands u can do the coding with the cheaper 1k tablet.
@@LMAutoRepairs Any recommendations? I've seen BMW branded ones which many say are CTEK ones with a BMW badge. CTEK themselves have loads of models. I have a few LIDL trickle chargers that I use to keep on some old cars so the batteries don't use charge from under use. But I have no idea what sort of one I would need for my E92 330D if I was to attempt any programming on it.
@@abeetha As i said, ideally you would use something like this... www.cardiagtool.co.uk/professional-intelligent-programming-charger-zlp100a.html I am using this one... www.halfords.com/motoring/battery-maintenance/battery-chargers/ring-rcbt27-pro-27a-battery-charger---12v%2F24v-116438.html I don't do programming on a daily basis, not even close... so I am happy using it...
helo i heav same problem with may bmw the error is 2e3c (deasal electronics:electronic immobilizer anti tampering protection) and i dont now what i nead to doo
Hi It can do bidirectional control of loads of components... I personally, never tried the vanos... but I can't see it no be able to... Thank you for watching and for your comment!
Hi, could you please let me know where you purchased Autel your 908p from as there are so many people offering good deals that I’m worried end up buying a bad one, Autel U.K. seems expensive compared to online retailers, I just need to find the best retailer , thanks, Chris.
This it is just an example... Didn't took long...😊 www.ebay.co.uk/itm/Autel-Maxiflash-Elite-J2534-ECU-Programming-Device-/154363911798?_trksid=p2349624.m46890.l49286 Contact autel, or check their website... they also sell it separately... That said, ensure is compatible with you tablet... As you need a subscription in order to download the files etc...
thanks for a quick reply. apprently in the UK you have to put it in as VW lt3 then you can access the program im trying to adjust the odometer mileage, but cannot change it.
Hi Double check... but my MS908P continues to work as normal... except for the online services.... like flashing etc... So, I presume yours will be the same... Hope that helps. Thank you for watching!
u can keep using after updates expires including for program and code, the only diff is u wont get no more updates for the newer vehicles...u have to pay another subscrition
Luis, awesome and good info thanks for sharing ur knowledge so you placed usb cable between laptop and autel 908 and which website you had in ur laptop and without subscription can you buy updates from manufacturer. thanks and cheeeers
Hi In this case was purely to demonstrate the procedure. Look on my channel, I have videos where I change modules, with used ones, and the programming was necessary... Thank you for watching!
Thank you for everything. I appreciate your videos. When using Maxisys for programming, do you need to be connected to Wi-Fi in order for tool to be able to program, or is the updated software file built into the scan tool?
@@LMAutoRepairs Thanks bro. I have looked for it in all the options and I don't get it. Basically my problem is that the car arrived with missing or incomplete software codes on dme. I updated and those codes left but now I get the code on dme 2f49 immobilizer anti-tampering protection and the crank but no start vehicle. No spark. Could it be synchronization? Can you enlighten me? any suggestions?
@@jimmygutierrez7242 Was the car starting when arrived to you? Have you checked the VIN on both, DME and CAS? If one of them has been replaced, will not work untill the ISN is transferred... MaxiSys can't do it...
Programming or also known as flashing, is the update of the actually software of the module... coding is more like enable or disable options etc... Hope makes sense... Thank you for watching and for your comment!
LM Auto Repairs thanks for your answer. There are some idea that Coding sometimes knowns as adaptation. Beacause when replace module. Just need coding for all module realise, not need programming right?
Maxisys can program it no problem... VIN number etc... However, it fails to reset the immobiliser on it... for that you have the IM608 for example... 👍👍👍
Hi Luis. Can the MaxiSys MS908P program a replaced ECU on a BMW? In my case an E series 520d (E60). My friend has replaced his DME and he was trying for days to program it using the IM608 but he cannot do it. I know the IM608 is more for key programming but it can do a lot more than that. Another great video by the way. You keep posting and I'll keep watching. Thanks a lot.
No... None of the Autels (MS908P or IM608) can do it through OBD... The IM608 if I recall correctly, can do some ecus... to program the engine ecu, you need to take the ISN from the CAS and write it on the ECU... or vice versa... 👍👍👍
Coding is more like change options... programming, is like updating the actually software/firmware inside the modules... Hope it makes sense... Thank you for watching and for your comment!
@@LMAutoRepairs HI FRIEND I HAVE THE SAME SCAN TOOL BUT MY SCREEN WHENT OUT SO IS THERE ANY PLACE WHERE I CAN GET MY SCAN TOOL TO GET IT REPAIR. MAXISYS MS908P
I have this model and I have just scratched the surface of what it can do. Thanks for the video.
👍👍👍
Thank you for watching and for your comment!
Your not going to have to scratch a whole lot since they leave alot of coverage out!!!
He probly meant no harm but !!When he gets to 3:30 he mentions to jump start the car to raise the voltage when no maintainer available ( a BATTERY MANTEINER IS NEEDED, a 15 to 25amp unit 20USD TO 50USD is more than enough to raise voltage, I used a 15amp unit for complete update). If u jump the car for programing, either u r going to burn the junction module or ur ecu/pcm/dme (if ur car battery is healthly plus jumping from another car with a healthy battery plus the altenator current frm the other car !!it will create an overcharge and burn modules). I FOLLOWED HIS ADVISE PROGRAMMING WHILE JUMPING AND MY JUNCTION MODULE BURNT WHILE PROGRAMMING MY BMW v6 328I. SINCE MY MAIN ECU/PCM/DME LOSS POWER WHILE PROGRAMMING IT DIED. !!I HAD TO BUY ANOTHER JUCTION MODULE FRM EBAY(2 JUNCTIONS THE FIRST THEY SENT WAS FAULTY) HAD TO BUY AOTHER ECU/DME/PCM EBAY AND IGNITION KEY WITH CONTROL AND A FOOTHWELL MODULE LINKED TO THE ECU FROM SAME EBAY SELLER (THE FOOTHWELL MODULE CONTAINS INMOBILISER DATA) AND 30USD BATTERY MANTINER TO PROPERLY PROGAM MY BMW AND GET IT RUNNING. He should have at least mention that when jumping from another car that the other car has to be engine off, and even so not sure if it wud work that way...….bmws and any vehicle 2005 and up should not b jumpstart frm another engine on car (risk of burn module), proper way to jump is with a cheap 30usd to 90usd lithium jumper or equivalent, or jump frm another car engine off at risk (on older vihicles it was ok to jump start from another engine on car cos the batteries were usually completely drain( probli owner left lights on) newer cars dont ever completely drain cos auto lights off or auto shutting electrical when volts low)..the only time ill risk jumping from another car with their engine on is if I was driving a v8 or larger v6 and they were driving a small v4..if it was the other way aroung me drivng v4 they driving v6 v8 I would only jump if their engine was off
Hi
I feel really sorry for what happened to you...
Watching my own video now, I realized I said jump the car... when what I meant was connect the maintainer...
I use a 30 amp charger/maintainer...
You can indeed program (not BMW really... due to the higher voltage required...), jumping from another battery/car, but both engines off... I did it few times before I bought my maintainer....
Once again... sorry...😔
@@LMAutoRepairs its ok..ill sue utibe not u...its good that we share info to help each other out...like u I also self-taught my self to use the tablet.
Gretings from Puerto Rico!It's been a while since I wrote you, but I always share your videos on my workshop page.Excellent video mate!
Just a little detail, you forgot to show how to connect the MaxiSys via internet and the car connections.
Just for those, who dont know how to do it and recently buy a MaxiSys Elite or Pro.
Hi
I will do next time...
Thank you for watching!
pedro l rivera negron it’s in the set up manual not that hard to do tho
this machine has all the programming and encoding modules the same as the ista esys etc program to encode tabs quadrants NBT screens thank you for your help
Yes...
👍👍👍
@@LMAutoRepairs so it does everything that an original eth cable type machine does, having this machine I don't need the bmw machine or the programs?
Pretty much...
Just that ISTA has guided diagnostics with diagrams etc... the Autel doesn't...
@@LMAutoRepairs thank you my friend I appreciate your availability and thank you for helping me because I'm buying a machine like this expensive and complicated😅
👍👍👍
Which diagnostic is the best one to buy ?
The does nearly everything ?
There is no such tool...
You need to compromise depending on what you really need or want...
👍👍👍
@@LMAutoRepairs thank you generally which is the best one to buy ?
@BK-it6te
Again, depends...
If you just require general code reading etc... any low-mid range will do, the likes of Autel, Topdon, Launch...
If you require more in depth then you have other tools for that...
Or, if you need it just for a brand then other tools apply...
You are not saying what you actually want it for, so it is difficult to say...
Anything that costs over 3000 dollars should satisfy You
For a while
Two questions on your autel coding.
1-were you connect to internet ?
2-did you have access to dealerships system?
Hi
1- to my WiFi...
2-yes, to the ones autel supports...
Thank you for watching!
Dear LMautorepairs. Can you program in same matter a used Cas3 module on a 2013 bmwc328i?
Dear LMAUTOREPAIR, Can you reprogram a used Cas3 module on a 2013 bmw328i in the same matter with this autel?
@derkdevries328
Yes... but, the immobiliser side of things will not be changed...
So, keys will have to be programmed separately and not with this tool, as it not capable of that...
👍👍👍
@@LMAutoRepairs thanks LM. Im508 should be able to prgram key again..if i also have that right? I see people going thru lots of bench set soldering etc on the cas which is connected to the cas. Wonder why take all the headache if you could just do it through the obd port? Afterall your wifi server support for bmw as you mentioned is kind of in your ms908
I use ctek 25 amp for some BMW that is also not enough but I tested it with picoscope for ripple there is 0 AC ripple from a ctek msx25 unit
Hi
I do have a battery maintainer now... bought a good one in the mean time...
It is a 30amp, used it loads of times after, and seems to work ok.
👍👍
Thank you for watching!
Hi which maintainer did you get as im after one at the moment.
@@gunti80
Hi
I got this one...
www.halfords.com/webapp/wcs/stores/servlet/ProductMobileDisplay?catalogId=10151&langId=-1&categoryId=255205&productId=1078771&storeId=10001
@@cambam2430 I did a complete program and code with 15amp battery charger/maintainer..whole process took around 40mins...
@@cambam2430 sorry sir dint mean to sound rude....puck bmw they lie and trick people so much..example the crank sesor the way they route the wiring overtime the sensor wiring gets loosed causing problems..the manual states that the sensor has to b removed from top when it can b removed frm the bottom really quick after throwing in the garbage all the plastic on the bottom and the little plate with unusual retainers that prevent ur hand frm fitting thru the bottom and rerouting and connecting the harness to the sensor.....I also threw in the garbage the bmw plastic thing that cover the coils and make it longer when testing and removing anything under that area.
Thanx for the video. May l kindly ask the location of a power steering module of a mini cooper B1 model.
Hi
Is that the electric version, correct?
👍👍👍
Can I program my new FRM module with these type of scanner tools
Yes...
👍👍
I installed Fan cooling Ecu in e90 N46n. It only works once at startup. Do I need to code it?
🤔
Probably...
👍👍👍
Hello,I do not know if my scan has a problem, the program does not work
I'm just wonder (i dont have BMW) why in this car fuel pomp need to be programmed?
Slawek h everything in our Bmw are computer ran and vin machine ECU etc. anytime you change out hardware even a battery you need to reprogram
Great video. What is the purpose of programming? I’m buying a Mercedes and want to do all the service and maintenance my self.
This was just a demonstration...
The programming can be beneficial is has been released new versions to correct small problems...
A bit like updates...
But you need specific tools to do such thing...
Thank you for watching!
👍👍👍
Thank you for your response would I need to buy the autel package that comes with programming tool or can I go with standard package just to maintenance like brakes and oil changes and smaller issues?
Yes... for that you have other tools from Autel and other makers...
Is the passthru protocol only for bmw and merc? Also u have to pay to connect and do the updates?
No... the J2534 is compatible with other OEM softwares...
The updates ect are included with the anual subscription...
Thank you for watching!
@@LMAutoRepairs great keep up the good job, and aks me if u ever need help. i always seems to get cars that nobody can find whats wrong!
I tried to the same thing as you but I don't get the same options as you and also I cannot even program a key its for a 2003 BMW X5 e53. is there a problem on my maxicom or is the car to old
The Maxicom does not have those capabilities...
Not even the Maxisys can do keys...
Thank you for watching!
@@LMAutoRepairs but why can i not update the ecu
@@2slow818
Maxisys 908p does it...
I don't believe the Maxicom doe it...
Check on Autel website...
Thankyou just been trying to find out if autel updates software
👍👍👍
Hello.
Is it possible to code/programming AUX with this to an E61 BMW?
Tanks
Yes it is...
But if that is the only thing you need, will be cheaper to get NCS...
Thank you for watching!
LM Auto Repairs
Thank You. I have this system :-) But dont know how to do it. Do you know? Thanks LM
@@marcusb9365
Programming... check under retrofit...
If is not there, check cheat coding...
If not there, add +NAUX to the VO/SA/FA and code the car or the affected modules...
Tank you for watching!
Thx for the vídeo luis, it may be a stupid question but here it goes what sort of situation would have to programme a car module...
Hi
I give you an example...
My 7 series, had for a long time a fault with one of the airbag modules... would come up with something like internal failure...
Clear the the codes, would last for days, sometimes weeks and even months....
Has been doing it for 2 years... I was too lazy to reprogram it...
But finally done it around Christmas last year... no issues ever since...
This is just an example... the manufacturer sometimes releases updates to rectify or improve deliverability etc...
Thank you for watching!
LM Auto Repairs cool thx Luis...👍
i know you posted this question 5 years ago.... but if you or anyone else happens to read this..... ALWAYS remember that if you do not know the answer to a question you may have, yet you want to know the answer to said question to benefit or learn from it because you genuinely want the answer, then no matter what anyone says.... there's no such thing as a dumb question in that instance!
@BruceAllentools
☺️
Absolutely!
👍👍👍
The shift solenoids. I asked transmission shop for an estimate to replace the solenoids and they told me they couldn't do it cause they had to be key coded and they didn't have that capability. They might be wrong.
Yes... the solenoids alone are just an electric valve... no coding required...
The entire mechatronics is a different story...
Both Launch X431 Diagun IV and Autel MaxiSys MS908P can do module programming.seems Launch have a better price.
Probably...
Thank you for watching and for your comment!
just came across this video .. interesting .. but why did you need to re-program the fuel pump , was it from another car?
Not in this case... was purely for the video...
I have videos on that though... programming modules from other cars...
👍👍👍
@@LMAutoRepairs thanks, I keep searching for any that I have missed.
Seeing an Error when trying to get a module programmed. Any advice or help? Error States: Connected vehicle has an unknown data status. It is not possible to handle this one with diagnostic tool. Ensure that the latest version of diagnostic tool has been loaded or contact after-sales department. When the measures plan was calculated a field appeared. Possible Fault Cause: Integration level (S15A-20-03-524) is incorrect or too new. Any ideas here?
As always thanks for the videos. You are the best.
Lol
Thank you for watching!
Does the artipad 1 can make multiupgrade and after that update the level status ID in car ?
I have only used it for a limited amount of time... but I believe it does...
Thank you for watching!
👍👍👍
Hi. I have the MaXiCom, just wondering will it reset and update the service history on bmw car? Thanks
It does... but don't think it does on the newer models, that do it on the idrive...
At least I have never tried it...
Thank you for watching and for your comment!
mini cooper 2015 can i update DME in car with only my autel ms 909,without connecting to bmw with J2534 ?
Don't think you can...
Thank you for watching!
I updated mini and the car shut down and won't start😢 any suggestions thanks
What you mean the car shut down?
You were doing it with the engine running?
@@LMAutoRepairs no it wasn't running, but update stoped and I tried to start it, no start now🤔I think might've wiped the ecu...thanks for getting back to me.. I did it wrong and down a mini diesel file I think form autel,when going into ecu for engine it says it's diesel but it's petrol😑
Any help on this one?thanks
@@davidcarroll4227
Try it again...
Make sure you have a good battery voltage at all times...
Is the jbox only using for ecu programs? Please advice .i am new for autel scanner thank you
The jbox is the interface that enables the communication between the car and the tool...
Being a J2534, is also compatible with flashing capabilities and the option to be used with some OEM softwares...
👍👍👍
We want to conduct Transmission change with Used one. Can we do Programming and Coading same process for BMW 740i 2010 model F02
Yes you can...
But... the gearbox might be coded to the immobiliser... Maxisys does not do it...
IM608 does it...
The reason that lead me to buy it, was actually to do it on a F10...
Thank you for watching!
I have the Autel MS908SPRO and I know it does programming because I have the J box with it. I wanted to know if if could be used to program a new CAS module and key for BMW 530I or will I have to send the module out for programming?
Hi
It will program and code the CAS... but, unfortunately will not program the keys...
👍👍👍
@@LMAutoRepairs ok thanks and I'm going to program a new CAS I purchased but wanted to know if the keys needed to be programmed before or after the CAS?
If you have the tools, you can program the keys on the bench before program it to the car...
@@LMAutoRepairs Ok I brought the Autel KM100 so I should be able to program the key to the CAS after programming the CAS in the car.
☺️
Never used that tool...
Let us know how it goes...
🤞
🤞🤞🤞
hello friend, my car currently running with a ecm frm a used donor bmw, got everithing program...my question is, using the 908 do u know if its possible to erase the vin frm a donor ecm and so only the vin frm my veicle poping up wen doing emissions test...they dont want to give me the little plate sticker unless I fix thar issue....usually wen I connect the autel it will ask me to choose my vin n the donor ecm vin
When you flash/update the module, using the Maxisys, if you "tell" her the modules have been replaced, it will update the vin during programming...
I have a video on my old e65, changing the Airbag gateway, and i show just that...
Hope it makes sense...
Thank you for watching!
@@LMAutoRepairs thanks..ill look at the vid asap
so when i plug my scanner all in with jbox and go into programing and coding it runs the scan through all modules but only gives me 2 options after coding and car/key memory what am i doing wrong please help
Which scanner are you using?
Thank you for watching!
@@LMAutoRepairs 908 pro with the jbox
Wich car?
2004 bmw 330i transmission starts in 3rd gear with transmission light on dash
Hello my car has modules from other cars. will this method update also the vin on the module?
Yes...
Thank you for watching!
I have a 2001 Volvo s40. Can this device activate fog lights for the vehicle? My car did not come originally with fog lights but the plugs was there and I connected to oem fog lights.
Possibly... I never checked it...
Otherwise VIDA will...
Thank you for watching!
Programing it's like flashing yes? Or not?
Yes...
👍👍👍
@@LMAutoRepairs Thank you! I want to buy it, but i need olny flashing ))) Have a nice day, thx for answer my q)))
hello can you ask me a question for the bmw brand which machine advises me to 908s pro or elite 2 thank you answer thank you
The Elite is the one above the MS908P...
So, I would recommend that one...
👍👍👍
@@LMAutoRepairs thank you very much for your reply
Hello, I also recommend Elite, because I am also using this product and the experience is not bad.
This is a video of me using Elite to perform online programming for the Transmission module of Audi A4L: ua-cam.com/video/ulewXsAKls4/v-deo.html , share it with you here, you can refer to it.
A video of the function performed for the BMW is also in my shooting schedule! If you are interested, you can click to take a look, or give me your opinion.
There are more videos on my homepage of using different devices to do different functions of the car. You are welcome to follow me and I will be happy to answer your questions. thanks.
can i code the elsd on my bmw 130i 2006 with the autel?
Most likely yes...
Thank you for watching!
I was offer a maxisys elite for cheap but it is out of subscription. Can it still do BMW programming? What message will I get if not?
Here in the UK you can't... Will just fail to download the software...
Check out with Autel if you leave elsewhere...
As someone was saying that in the USA you can still programming...🤷♂️
Thank you for watching and for your comment.
Hi. Quick question. Is it possible to program the ECU from another car? Second hand? thanks
u can as long as u also buy the keyfob and cas module that belongs to the ecu.....the only issue wud be that if u live in a state with extremely strict smog rules it might not pass....6/16/2020 I was instructed by a star smog tech to get in contact with state referi to fix my issue wer my car has ecu ftm other car../////6/11/202 usually when I coonect the scanner to my car that has ecu frm another car it will ask me to choose between my vin and the vin of the car that the ecu came frm....tried smoging prior and the tech said som bulls..t story that his computer cudent connect to my car.....im asuming if u buy a brand ecu ter wudent b that issue....I cant affor new ecu so if noone wants to pass my car, ima just paint the sticker with glitter nail polish to corresponding year color, n use a gps jammer so my car does popup as a red dot on cops map screen...but ten they might b wondering why my car not showing up in teir screen since its modern car or tey might not even notice epecially in city with alot of vehicles...probly I wud only get caugh if I get pulled over and cant provide up to date regristion papers.
What’s the difference between this and BMW ISTA? I thought only ISTA could do programming? So confused
Hi
ISTA can do programming, yes, and is the OEM system...
What are you confused about?
Thank you for watching!
LM Auto Repairs I guess what I mean is, if you have this, do you need ISTA? Like do they do the same thing? It seems this is better obviously as it does all makes and is portable. Downloading ISTA seems like a job in itself.
@@Chris-rs3dj
Not really... with this tool, you don't really need ISTA... the only thing with ISTA, is the wiring diagrams, testing components etc... that obviously this tool does not have...
👍👍👍
How to programing best tools ?? .. Autel I'm 608 autel mk 908p. How to best programing tools ???
Nothing like starting a video in the middle of the process. Any special cables or connections?
Is on the video title...
"...using Autel Maxisys MS908P."
🙄
Hi thanks for the info. I see it has a retrofit and conversion tab, I have swapped my gearbox for a 6 speed from a 5 speed and retrofitted cruise but cruise only works up to 5th gear and when I change to 6th gear the cluster display only displays up to 5th gear and goes blank in 6th will this do this? Many thanks
Possibly...
Never done it...
👍👍👍
Where about are you based? Wanna try? Obviously pay you! 😊
LM Auto Repairs
Great video!!! can you reprogram/coding the cruise control, mine its not working for some reason and I would like to have it back, Thank you!!
Hi
If was working and it stopped, is probably nothing to do with coding or programming...
Most likely there is a fault somewhere inhibiting the cruise control..
Scan the car and look at some live data to find out what's happening...
Hope that helps.
Thank you for watching!
Which mode it's the best for BMW serie F upgrade just one module or make multiupgrade?
It is advised to update everything...
But most of the times you get away with update only individual modules...
Thank you for watching!
What did u use to program the car I have the 906 bt what else do I need
You need a J2534...
Your model is different...
👍👍👍
@@LMAutoRepairs so that will work for the 906 bt
Don't think it does...
The VCI is not the correct one...
Hi. Can this do updates on outher makes or it just updates bmw and mercedes thanks
Flashing yes, only BMW and Mercedes...
Thank you for watching!
👍👍👍
What is the difference between coding and programming???
Programming usually refers to the writing of the module software... also knows flashing...
Obviously Programming can refer to other software updates etc...
Coding refers to the changing of settings/parameters, in this case to match the car's options etc...
👍👍👍
@@LMAutoRepairs thanks brother !
I tried programming my new headlights to my 2017 bmw 330i, it required Ethernet connection, I kept running into connection issues. In the autel diagram I have to use the special adapter that has both Ethernet cable connection and OBD port, and then it says to poking Ethernet cable into the autel MS908P. Can I just use a personal hotspot that can connect to the connector and tablet via Ethernet ?
Yes... you need the ethernet adapter for the F series and above...
It is not expensive...
I believe on the new 908 that adaptor come with it... not on the old ones... I got my one from Autel directly...
It is something worth to have...
I never tried any workaround, so not sure if it is possible to do it in any other way... I would say no... As the autel needs to connect to the car through the ethernet to the car...
Thank you for watching and for your comment!
@@LMAutoRepairs I have the Ethernet adapter and everything I’m just not sure on how to connect it, if I can’t have WiFi on how is the autel supposed to download the file needed for the programming? Do you know how to set up the Ethernet on the device ? I tried and still can’t figure it out
@@LMAutoRepairs and I can’t use hotspot because it doesn’t allow me to have WiFi on
😊
The Autel will automatically switch between the ethernet which will be connected to the car, and the Wireless when it needs to download files...
Don't need to worry about that...😉
@@LMAutoRepairs so To clarify, I can use the personal hotspot on my iphone to connect to the autel to the internet, and then once the Ethernet is connected to both the OBD and the autel, it will switch between automatically? Because I tried that and then i was getting a “no vehicle communication” pop up on the autel
Hi guys very good video , I have a Autel 908 but dont have the pass through tool j..... can I purchas add this to my 908... I presume i will need my subscription updated to Autel. Thanks Autel is awsome
I believe you can...
You need the j3524 and the subscription updates... but confirm it with Autel themselves...
Just to make sure...
Thank you for watching and for your comment!
Hello, can you CODE Auxiliary to a 2004 bmw 530i on Maxitool so it can show on the display screen ? It only shows FM/AM/CD I installed auxiliary but it won't show on screen and I read it needs coding but most videos I've seen are done on INPA but I have Autel Elite scanner. Thanks
Autel should be able to do it...
Either by editing the VO, or under retrofits...
Thank you for watching!
@@LMAutoRepairs do you know anyone that had done it on Autel ? Or do you know of any link on UA-cam for it ? All what I found was INPA
Not INPA... you can't code with INPA...
Is with NCS Expert...
Again, autel will do it by modifying the VO...
Just add +NAUX to the vo, save it and the code the ccc and all the relevant modules...
Quite straight forward...
@@LMAutoRepairs does VO means vehicle operations ? Not sure what you mean exactly by VO and CCC Sorry I'm not finding the right way to do it 😭
Do you mind sharing the steps ? Truly appreciate your time
VO=Veichle Order
CCC=Car Communication Computer
There is step by step guides out there... I am sure...
I don't remember now from the top of my head, and if you need a step by step guide, I don't want to give you inaccurate information...
Do you have to have a laptop to program are u can use just that j box
The J2534 is compatible with a few OEM softwares... check Autel website, I believe they have a list in there...
Thank you for watching!
👍👍👍
Do you know if you can code replacement transmission solenoids on a 2012 335i with an Autel 906bt?
Never used that tool...
Not sure if the solenoids need to be coded...
Or are you talking about the whole mechatronics?
Thank you for watching and for your comment!
Dear friend I see yr video when u did the mart car updates the software for transmission and u said u have A CD for it can you please let me know where i can find it
With all those computer parts laying around you should have a power supply to use for battery maintaining. Thank you for your time making these videos
Hi
I do have one now...😉
Thank you for watching and for your comment!
@@LMAutoRepairs out of curiosity what brand and model did you took?
@@michmich9258
Hi
Ring
Trade Charger 27
Thanks you for watching!
how do you even get to that very first CIP screen?? I can't find it anywhere....
Should come up on the first main screen...
Thank you for watching!
I have a 2012 bmw 528i where it stalls out in the middle of traffic when I step on it what can the problem be? Where can I buy this to program the ekps for it I bought one plugged and played but it would not run
What program are you referring to exactly?
Thank you for watching!
@@LMAutoRepairs el Mismo aparato the same thing you have or anything else that's a bit less pricey bmw Is charging me 4000 to change the ekps and install a new fuel pump
@@Luis92r
What is the exact problem with the car?
This scanner is not cheap either...
@@LMAutoRepairs it throws code p0087 but goes away if I go to step on the gas hard to pass it feels like a thud then the engine just shuts off if you try to give it gas while rolling the computer on screen says fuel supply drive moderately I have to pull over to shoulder as fast as I can and then the engine shuts up if you try to turn it on again immediately it just cranks but will not start after about 20 to 12 mins later while car is off completely the car will just turn back on like normal and I can keep driving it does it randomly BMW charged me 200 to tell me it's the fuel pump that needs replacing and the ekps module, they are trying to charge me 4000 for parts and labor.
@@Luis92r
I would take it to some good independent garage...
I believe that that model has 2 fuel pumps...
A low pressure one in the tank, and the high pressure one under the bonnet...
It can be any of the two failing...
The one under the bonnet, the high pressure, don't think it requires any programming... so if BMW is telling you that, means the other pump... 4k for that, seems a bit exaggerated to me...
Hope that helps...
Can Mysis enable/Install Sat Nav on Toyota Hybrid 2015 model?
Never tried it... sorry if I can't help you this time...
Thank you for watching!
Nice video👍
Can we program a used FRAM for bmw with ISTA?
Thank u
Never done it with ista...
But I believe you can...
👍👍👍
How did you get to that menu?? I have MaxiSys but not menu like that on mine.
I'm trying to code headlamp on a 2015 RR4 Rolls Royce Ghost.
Under programming... on the first menu once you load the car details...
Thank you for watching!
@@LMAutoRepairs Unfortunately, for RR there is no programming option...
Just 3 options. Diagnostic - Service - Vehicle profile.
@@Avechuchoaxel
I have never worked on one...
What about F series programming / coding? it needs a enet cable? any other option?
Thanks
The Autel has that cable...
👍👍👍
Thank you for watching!
Dose it support BMW i3, All modules including high voltage battery ? I like the tester, seams good:)
Never tried on that car... can't really advise...
Thankn and for watching!
Hi. can you update bmw e60 climate control from manual to automatic with autel? ofcourse after all wiring was done befero.
Hi
Yes... should be relatively easy to change the VO and update the car...
Thank you for watching and for your comment!
@@LMAutoRepairs thanks for your quick reply. Did you ever try to to program out the passenger seat occupation sensor with autel? I know it fails a lot of times in the bmw, I know that you can do it with ncexpert, but I'm interested about autel capabilities. Because I just ordered one.
@@modestasserpenskas2353
Never did one i think... i mean, not with the autel... but under cheat coding might be possible...
Just go through the options available...
👍👍👍
Can you please help me with a question, what about the subscription? How does the Maxisys know meaning if i go onto Benz and pay for say a 2 day sub, how does it know my MaxiSys belongs to that sub?
It does not work like that...
You pay for 1 year, and you have access to everything until the year runs out...
@@LMAutoRepairs who do you pay 1 year too Autel of Benz? My autel I purchased June 6, 2018 and my free updates end June 6, 2020. . I read that my 2 year updated include the BMW and Benz subscription to program these cars. Meaning i don't need a separate sub for the BMW or Benz website to access the programming service is that correct?
@@loutech7209
You pay to Autel...
@@LMAutoRepairs thank you>
Hey buddy GREAT VID. Just a question. Can I use Maxisys or Autel to code replacement EKPM3 module that came from a different car but comparable? My car is an E82 2.0D 2008 & the part came from a 2008 E87 2.0D. Please let me know. Thank you buddy.
Yes... should be able to do it....
Thank you for watching and for your comment!
No worries. Keep up the good work. I was more wondering if I can use Autel to tell the EKPM3 that it’s now in a similar model but different car so it has correct flow values etc. If so can you point me in the right direction menu-wise that would be greatly appreciated? Thank you again.
The Autel is quite intuitive on that sort of stuff...
Watch this video...
ua-cam.com/video/pAKztvmr07g/v-deo.html
The principle is the same...
Once you flash the module with the software for the car, to change VIN number etc... and you code it... the module becomes part of the car... As if was fitted from factory...😊
Hi, Is it possible to program new CCC module automaticly with maxisys?
Pretty much yes...
Thank you for watching!
Hi, do you know if the j2534 with the autel can be used to programme other vehicles like Renault/ford etc? Thanks
It can... but not all those ...
The compatibility list on Autel website....
Thank you for watching!
yes it can it works with all or nearly all brands....and only bmw and Mercedes need programming for the rest only coding is needed....only bmw and Mercedes required this more expensive tablet....for all other brands u can do the coding with the cheaper 1k tablet.
Hi, Is it better to use a tool like MaxiSys instead of INSTA D/P for programming a BMW?
They both achieve the same result...
Thank you for watching!
@@LMAutoRepairs You also mention wanting to get a battery maintainer. Have you thought of which one you might like?
@@abeetha
I use one that is not really a maintainer...
Is more of a charger, but does the job quite well...
A proper maintainer is quite expensive...😬
@@LMAutoRepairs Any recommendations? I've seen BMW branded ones which many say are CTEK ones with a BMW badge. CTEK themselves have loads of models. I have a few LIDL trickle chargers that I use to keep on some old cars so the batteries don't use charge from under use. But I have no idea what sort of one I would need for my E92 330D if I was to attempt any programming on it.
@@abeetha
As i said, ideally you would use something like this...
www.cardiagtool.co.uk/professional-intelligent-programming-charger-zlp100a.html
I am using this one...
www.halfords.com/motoring/battery-maintenance/battery-chargers/ring-rcbt27-pro-27a-battery-charger---12v%2F24v-116438.html
I don't do programming on a daily basis, not even close... so I am happy using it...
Can autel MS906 BT for coding mechatronic BMW F10? we're from indonesia
yes, autel MS906 can do everything bro
what does it mean WRITE CKM SETTINGS?
The CKM is the Keys and Vehicle Settings...
Is the Settings of the Vehicle for different keys...
👍👍👍👍
helo i heav same problem with may bmw the error is 2e3c (deasal electronics:electronic immobilizer anti tampering protection) and i dont now what i nead to doo
Have you replaced the ecu?
Thank you for watching!
yes i clone the original ecu
Something must have gone wrong...
Or, you need to resync the ecu and CAS...
Which ecu is that?
for bmw series 1 118d engine n47
i jast disconnected the pipe for injector and is not caming fuel in injector. becouse i heav that eror
brilliant thanks Louis, did you ever get a battery maintainer? Any recommendations?
Kind regards Jay
I di have one, but is not really the recommended one...
Search for a smart battery maintainer...
Thank you for watching!
Thanks for the video great info. Can this scanner bidirectionally control the vanos solenoids on bmw?
Hi
It can do bidirectional control of loads of components...
I personally, never tried the vanos... but I can't see it no be able to...
Thank you for watching and for your comment!
Autel ms 905 mini knows the same things? I mean control units matching or resetting?
And coding? For example in bcm or pcm things enable or disable
@@martonhorvath1887
Never used it... so don't really know...
Check Autel website... surely there is some info in there...
Thank you for watching!
Can I used the autel app on the phone via Bluetooth
Never done it that way... so can't really advise...
Is that with the J2534?
👍👍👍
Hi, could you please let me know where you purchased Autel your 908p from as there are so many people offering good deals that I’m worried end up buying a bad one, Autel U.K. seems expensive compared to online retailers, I just need to find the best retailer , thanks, Chris.
Hi
I got my one from eBay... can't really remember now the seller...
Autel UK is indeed much more expensive...
Sorry if I can't be more helpful...
Hi when doing these do you need to connect the internet cable direct to the obd cable
No... the tool has WiFi to connect to your Internet...
Thank you for watching!
But does this Autel get down into the MOST BUS in the BMW?
You can still update the most modules, but through the can...
Autel does not have a direct connection to the most bus...
👍👍👍
Hi great video! I have smashed my headlight on my f20 1 series and im putting a used one in. Will this tool program the light into the car? Thanks
I guess it will... if needs programming...
Thank you for watching and for your comment!
Hi there, where do you get the J2534 cable from?
Comes with the Autel... As part of the MS908P...
Thank you for watching!
@@LMAutoRepairs ah okay, i have the MS906BT which it doesn't come with, (only the Bluetooth VCI) cant seem to find where I can get it from separately
This it is just an example...
Didn't took long...😊
www.ebay.co.uk/itm/Autel-Maxiflash-Elite-J2534-ECU-Programming-Device-/154363911798?_trksid=p2349624.m46890.l49286
Contact autel, or check their website... they also sell it separately...
That said, ensure is compatible with you tablet... As you need a subscription in order to download the files etc...
is it possible to calibrate the DSC with the Autel? My boss has a BMW and evidently I am the only person in the shop willing to figure it out lol
Never done that, but I would say it should be able to do it...
Thank you for watching!
👍👍👍
@LMAutoRepairs can this Autel 908p change bbattery capacity on BMW ?? 906 can't do it so I wonder if we can with 908p
I know it can, not sure if in all models though.
Thank you for watching and for your comment!
Hello. How much is the machine price, do you have a used piece.
Hi
The 908p costs probably less than 2k now...
No... I don't have used ones... this is the only one I have...
Thank you for watching!
hi i cannot read vin with my vw crafter 2013 bluemotion van any help please i have the 908 max pro.colin
Which program are you using?
Use the VW CV...
Thank you for watching!
thanks for a quick reply. apprently in the UK you have to put it in as VW lt3 then you can access the program im trying to adjust the odometer mileage, but cannot change it.
@@colincourier
Yes... forgot the LT3...🤦♂️
No, you can't....
@@LMAutoRepairs ok thanks
Hello mate
Thanks for your videos
I would like to know if ms908s can program used Ecu?
Never used it... check on Autel website... there is plenty of info there...
Thank you for watching!
I programmed an used Ecu from ebay to my car with maxisys 908p, u have to buy the Ecu, cas module, control fob and key insert with wiring.
Im gonna buy ms908bt. Can i use it after a year also when the update service finishes? Or do i have to pay like 699 each year just to use it?
Hi
Double check... but my MS908P continues to work as normal... except for the online services.... like flashing etc...
So, I presume yours will be the same...
Hope that helps.
Thank you for watching!
@@LMAutoRepairs It means i can still use it same as after the subscription is over? Like i can still kode keys etc?
@@Saqib.S
Yes...
@@LMAutoRepairs Love you man! Cheers ♥️♥️♥️
u can keep using after updates expires including for program and code, the only diff is u wont get no more updates for the newer vehicles...u have to pay another subscrition
Luis, awesome and good info thanks for sharing ur knowledge so you placed usb cable between laptop and autel 908 and which website you had in ur laptop and without subscription can you buy updates from manufacturer. thanks and cheeeers
Hi
The updates are included on the annual subscription...
Thank you for watching!
j georges you need a subscription and update right from Autel you can get third party software no such thing.
usb cable goes between autel tablet and autel programming module to ensure there is no data transmission problem when programming
Hi why you need to program the module? You changed it? New or used?
Hi
In this case was purely to demonstrate the procedure.
Look on my channel, I have videos where I change modules, with used ones, and the programming was necessary...
Thank you for watching!
Thank you for everything. I appreciate your videos. When using Maxisys for programming, do you need to be connected to Wi-Fi in order for tool to be able to program, or is the updated software file built into the scan tool?
Hi
You need a live connection... as the software is downloaded fr9m their servers...
Thank you for watching and for your comment!
@@LMAutoRepairs hi. is it free? or it will charge with upcoming updates?
@@modestasserpenskas2353
Hi
Is part of the anual subscription...
Thank you for watching!
Hi bro. Can I do cas and dme synchronization with autel ms908sp? BMW e90, 328i 2008.
I am sure you can...
I seen that option when navigating through the menus...
Thank you for watching!
@@LMAutoRepairs
Thanks bro.
I have looked for it in all the options and I don't get it.
Basically my problem is that the car arrived with missing or incomplete software codes on dme. I updated and those codes left but now I get the code on dme 2f49 immobilizer anti-tampering protection and the crank but no start vehicle. No spark.
Could it be synchronization?
Can you enlighten me? any suggestions?
@@jimmygutierrez7242
Was the car starting when arrived to you?
Have you checked the VIN on both, DME and CAS?
If one of them has been replaced, will not work untill the ISN is transferred...
MaxiSys can't do it...
Hi. I want to ask you if it has an error code you can program Theorell.
Should do...
Thank you for watching!
Could you tell me the different between Coding and Programming?
Programming or also known as flashing, is the update of the actually software of the module... coding is more like enable or disable options etc...
Hope makes sense...
Thank you for watching and for your comment!
LM Auto Repairs thanks for your answer. There are some idea that Coding sometimes knowns as adaptation. Beacause when replace module. Just need coding for all module realise, not need programming right?
@@vunguyenminh1774
It is a bit more complicated than that...
But normally a new module needs programming and coding...
@@vunguyenminh1774 ...only bmw and Mercedes need programming and coding when replacing modules, all other brands just coding
Thanks for sharing such a helpful video, can maxisys program a used mechatronics (transmission control module) on bmw F01?
Never tried it... so can't really comment... sorry...
Thank you for watching and for your comment!
Mech units have to go to dealer . This scanner can't program that.
Maxisys can program it no problem...
VIN number etc...
However, it fails to reset the immobiliser on it... for that you have the IM608 for example...
👍👍👍
@@LMAutoRepairs hmm that's why i had issue ...immo was why . Thanks that's good information .
👍👍👍
Hi
During the programming process, the net is disconnected ?
No...
You need an Internet connection to download the necessary files...
Thank you for watching!
Hi Luis. Can the MaxiSys MS908P program a replaced ECU on a BMW? In my case an E series 520d (E60). My friend has replaced his DME and he was trying for days to program it using the IM608 but he cannot do it. I know the IM608 is more for key programming but it can do a lot more than that. Another great video by the way. You keep posting and I'll keep watching. Thanks a lot.
No...
None of the Autels (MS908P or IM608) can do it through OBD...
The IM608 if I recall correctly, can do some ecus... to program the engine ecu, you need to take the ISN from the CAS and write it on the ECU... or vice versa...
👍👍👍
@@LMAutoRepairs That's what I thought. Thanks for your respond. Wishing you all the best!!!
👍👍👍
Pretty sure the MS908S Pro with the J2534, can program a new or used ECM on BMW and Mercedes. But only those auto makers. The rest, no.
Hello how i can do menu m in bmw f20 i have maxicom 908p
Possible through coding...
Or FA editing...
Never done that, so don't take my word for it...
Thank you for watching and for your comment!
Great Video mate, May I ask whats the difference between coding and programming?
Coding is more like change options... programming, is like updating the actually software/firmware inside the modules...
Hope it makes sense...
Thank you for watching and for your comment!
@@LMAutoRepairs HI FRIEND I HAVE THE SAME SCAN TOOL BUT MY SCREEN WHENT OUT SO IS THERE ANY PLACE WHERE I CAN GET MY SCAN TOOL TO GET IT REPAIR. MAXISYS MS908P
@@seankim1743
Not really... sorry...
😔
@@seankim1743 unfortunately, the only place to fix one of these is at Autel in California. www.autel.com
Hi Darling, how can I controlling injectors fuel quality by autel maxisys ms908 pro? Thaks
I have a question can this program bmw cas 2 keys ?
No.
Thank you for watching and for your comment!
yes u can program and code the cas module(car acess system) and keys
@@cal638
You have to show that...
@@LMAutoRepairs I don't have a video but its a requirement when programing a used ecu and new keyfob
Does it work with programming the transmission mechatronics?
Yes...
Thank you for watching and for your comment!