I have a few used modules I have been wanting to mess around with, just have not had the time. Thanks for sharing to make others aware what they may run into (I see it in the field all the time) .
I changed the battery in my 2011 E350 van and now I’m getting a security padlock on the dash. Can you point me in the right direction so I don’t have to have it towed to the dealership?
I have a 2008 F350 SD. The Brake indicator, TPMS, Door ajar, are all on. The blinkers work, but don't indicate on the dash, just on the exterior (where it matters, I guess.) The radio also doesn't power on with all these faults but has power going to it. The backlight to the dash stays on and now I have to pull the negatives off the battery to keep it from dying. I've replaced the BCM as that is what most of the research points to, but that didn't fix it. A few forums said it could be a bad instrument cluster. Have you seen this error before? Thank you
@@IntegratedAutoModules The corrosion is on the large white plug in on the passenger side behind the kick panel where the fuse box/bcm is. There was a leak from the sunroof and water was dripping down in that area so it is hopefully that.
Ford f350 2008 diesel 6.4 Car was cranking no start , replaced ecm with another one Now security light flashing giving the code 23 by flash pattern So i put the original ecm back , still the security light flashes giving code 16 Also the owner don't have a key that opens the doors , the key he have only works for ignition Is there a way to override this pats system cause he doesn't need it ( actually it's a company cars , so the cars don't need anti theft system cause the doors always open )
Just seeing this now. Did you figure it out? Try reflash. The corrupt location in memory is luckily holding an instruction that hasn't completely f'ed the vehicle.
I have a 2008 f-350 that after it sat for a couple months the security light flashes and won't allow it to start. It just started this without changing any parts out
I have same problem battery went dead installed new batteries and no crank did a parameter reset but keys won't program could it be the cluster messed up, or do i but a new cluster 2008 F450 6.4L king ranch.
if you do a both keys lost reset you can fix it also reset then put new key 1 turn to run 3sec then off then key 2 turn to run 3sec then remove all keys for 3min, both keys should be programed at that point im not sure witch scanners can do it i do know most the newer autels do.
I have a few used modules I have been wanting to mess around with, just have not had the time. Thanks for sharing to make others aware what they may run into (I see it in the field all the time) .
I changed the battery in my 2011 E350 van and now I’m getting a security padlock on the dash. Can you point me in the right direction so I don’t have to have it towed to the dealership?
I have a 2008 F350 SD. The Brake indicator, TPMS, Door ajar, are all on. The blinkers work, but don't indicate on the dash, just on the exterior (where it matters, I guess.) The radio also doesn't power on with all these faults but has power going to it. The backlight to the dash stays on and now I have to pull the negatives off the battery to keep it from dying. I've replaced the BCM as that is what most of the research points to, but that didn't fix it. A few forums said it could be a bad instrument cluster. Have you seen this error before? Thank you
It could be the cluster or a missing power/ground.
You'll need a scan tool with security functions to pair the replacement cluster.
@@IntegratedAutoModules I found some corrosion on one of the plugs and will see if removing that helps.
The blue plug on the cluster? If so, then you likely found the problem.
@@IntegratedAutoModules The corrosion is on the large white plug in on the passenger side behind the kick panel where the fuse box/bcm is. There was a leak from the sunroof and water was dripping down in that area so it is hopefully that.
Hey I’m having the same issue are you still able to do this just got a new ecm in and that light is still blinking
Ford f350 2010 just wondering how it would work if I had you do the reset would I ship the pcm to you needing help atm
Ford f350 2008 diesel 6.4
Car was cranking no start , replaced ecm with another one
Now security light flashing giving the code 23 by flash pattern
So i put the original ecm back , still the security light flashes giving code 16
Also the owner don't have a key that opens the doors , the key he have only works for ignition
Is there a way to override this pats system cause he doesn't need it ( actually it's a company cars , so the cars don't need anti theft system cause the doors always open )
I have a code p1639 block id or corrupt the truck starts and all but how do I know it just needs a simple reflash
Just seeing this now. Did you figure it out? Try reflash. The corrupt location in memory is luckily holding an instruction that hasn't completely f'ed the vehicle.
My truck just started doing it. Where is the module located at?
Can you do a video on your dcl box you are using to power everything up?
Good video. Very informative
I have a 2008 f-350 that after it sat for a couple months the security light flashes and won't allow it to start. It just started this without changing any parts out
My truck do not have a chip on the key and he has that security light on?
Did u figure out what it is ?
@@anthonyscarfino7536 I’m having the same problem
I have same problem battery went dead installed new batteries and no crank did a parameter reset but keys won't program could it be the cluster messed up, or do i but a new cluster 2008 F450 6.4L king ranch.
Cluster could be bad or something on the CAN bus.
Do you guys have a website or email to contact you for PATS services? Thanks
Hi,
Send an email to Leac0071@gmail.com
How much do you charge for that
if you do a both keys lost reset you can fix it also reset then put new key 1 turn to run 3sec then off then key 2 turn to run 3sec then remove all keys for 3min, both keys should be programed at that point im not sure witch scanners can do it i do know most the newer autels do.
How do you remove the pcm
Hi! I need to reprogram my cluster like this video. Send me how I contact you guys. Thanks!
Call or text if you still need assistance. 612-860-9977.
So if the light stays on its the problem
Having the same issue with my 2008 6.4 diesel the battery’s was dead for a wile now the light flashes rapidly
Did you find out what the problem was
need help with my f350
I’m having the same problem
Did you recently replace any parts?
No my battery was dead for like a month put in a new one and this happened
Thinking I might have to reprogram the key
What year, make ,model, and engine size?
07 f250 5.4
I could use your help with mine
Hi,
Email details to Leac0071@gmail.com.
Having anti theft issue in 2008 f350
Did you figure it out yet
Solved ?
Help
I have a ford f250 5.4 4x4
Do you guys have a website or email to contact you for PATS services? Thanks