This is the best installation video for this part that I have seen, perhaps the only recommendation that I have and I see the others do too is turn the music down slightly or off. Thanks mate!
Perfect video, I needed this exactly and not only did you give great views and clear instructions but I appreciate you also giving tips and showing start to finish. Thank you! Have a blessed one!
Thanks for the video I’ll try mine when my part arrives , question what it leaks is it coolant ? Do I need to worry if I have to drive to work one more day till I fix it ? It’s not a big leak it’s leaking a bit
Just keep any eye on temperature gauge. Along as it never gets above half way no concern. MAKE SURE COOLING SYSTEM IS FULL. DO NOT GUESS. DYOR I bare no responsibility on that comment.
Don't wait for the overheating idiot light. Just raise the hood and look at the coolant reservoir right behind the latch. If there is any red fluid visible you will be okay. Check often and top off to the middle seam. Use only the red premix or distilled water in a pinch. I live in Phoenix and have no problems even in the summer.
I have a Chevy Cruze 1.8L Eco Tech Manual 6 Speed transmission. My thermostat housing seal started to leak (coolant fluid) after the thermostat throttle pressure (intake heater line) failed. I replaced the thermostat housing, but now the oil cooler pipe is leaking coolant. I replaced the o-ring and still is leaking, I think it needs a thermometer gasket? I will be replacing the throttle pressure intake heater line that runs from thermostat housing to the intake. #chevycruze #chevy #cruze
Yes it can. Take a look at your new pipe. See the very tip of the the male end of the pipe? The old peice will be stuck in your housing. Remove with pliers
My thermostat housing failed, due to the intake throttle pressure heater line. There is also a return line on the throttle intake housing that feeds back to the coolant reservoir. The brake booster cylinder also has a coolant pressure heater line. #chevycruze #chevy #cruze
I ask because I already have the replacement fitting and the hose is perfectly fine. It's just the clip on the plastic fitting that broke. So it pops out occasionally. So is there a way ? Lol
@@knimar0287 Did you ever find out where to get that plastic connector? Or even the entire hose with connector? just broke that little plastic piece changing out my thermostat housing...
Wrong! Do NOT use a screwdriver to pry up on the clip like he did, the clip might break or in his case, the neck below the o-ring will break (see the o-ring sitting on top inside the housing tube after he removed the fitting?) .. There is a tab on top of the clip to put the screwdriver in to pull the clip off the fitting.. When mounting, make sure o-ring is on the neck and push the fitting in the hole first, then slide the clip on the groves until it locks
@@thepartsfactory4239 Wrong again.. I had to remove mine because my thermostat housing assembly needed to be replaced (due to hairline cracks) and there was nothing wrong with the throttle body heating pipe (tube).. If you remove it like you did prying it sideways with the screwdriver, you will break the lower portion of the neck.
@ecarroll3723 Mate, stop with the condescending behaviour. 🤚🏽 you are absolutely able to use a flat had screw driver to assist to remove that clip. Yes if its seen some significant wear and tear in the form of heat cycles it may break. Take your pathetic attitude elsewhere 🤡🤡
He is not condescending, he’s just telling you how it is. Everybody can get it wrong, and we learn from our mistakes. You should take this video down, because you are basically showing people how to break the fitting. It’s in 2 parts, and the part that clips in simply pulls out towards the front, no prying necessary.
music kills, I was cleaning my expansion bottle when filled it in I noticed leaking on this pipe , while finding a way to stop the leak , I cracked the pipe into 2 pieces, I went to pick up the fuel hose 6mm for a temp fixed , all was good until when I remove the sensor part to insert the fuel hose, it cracked into pieces where I can not even hold with a clamp, I have ordered new one, but me needing a car for work, I have tried to hold it with a clamp hopeful there is no heat pressure in this hose pipe because , I really need my car this week
Make sure there is no snapped of bits from the last pipe. Ive had it where you try and push dowm but because there is left over peices it will not clip in.
Just noticed that mine broke as well on my 2014 Chevy Cruze when I started to smell antifreeze/coolant; checked and by the elbow it has a leak. Took me forever to find what this piece is called!!!
Very appreciative of your effort to make a vid, however - the music, great you've said its banished - the lighting .. why film in a dark workshop ? Park the car so that SUNLIGHT shines in from the font + your work light isn't constantly illuminating the area the camera is focused on, I'd suggest a Dewalt battery spotlight for the camera guy to hold & manouvre. - & the camera operator needs to focus both in and out with multiple angles .... preferably without your hands in the way. But again .... I AM APPRECIATIVE of your efforts. I've subscribed 👍to your channel bcaus: My daughter has just bought a 2016 Sportswagon Cruze ... which I've discovered has oil from valves leaking and pooling above between spark plug & coil (watched that vid 👍) any chance of a vid on rectifying the valve seal/rocker cover gasket/baskets ???
Sorry, but whoever decided that elevator music would enhance the quality of your video should get the dummy dust kicked out of him. I couldn’t stand half of it.
Turn off the music. Very distracting, and overpowers your voice.
Could live without the music in the background so i could hear better. But i did it myself. Thanks
This is the best installation video for this part that I have seen, perhaps the only recommendation that I have and I see the others do too is turn the music down slightly or off. Thanks mate!
Pro tip: don’t have the music louder than the directions
Perfect video, I needed this exactly and not only did you give great views and clear instructions but I appreciate you also giving tips and showing start to finish. Thank you! Have a blessed one!
You're very welcome!
Thanks man. I appreciate it. This help me alot. I liked how you moved the camera through the whole hose line.
You made this seem MUCH easier than it is. Lol thanks for the video
It's simple but a pain due to steps!!
You put the hose on without pulling out the broken piece. Thats what i needed help on
Came exactly for this too 🤣
Thanks mate!! (From Canada). We use the same engine here in the Chevrolet Cruze and Sonic. It's a great engine as far as I can tell.
Be careful! Its the cooling system that is the problem. Check monthly for leaks and/or gasket issues
Might like a stupid question, but the ecu is missing or did you already remove? Great video btw
Is there any reason why you couldn’t run a full hose from the thermostat housing and delete the original plug and piping?
I can’t see why not? Cheers
Thanks for the video I’ll try mine when my part arrives , question what it leaks is it coolant ? Do I need to worry if I have to drive to work one more day till I fix it ? It’s not a big leak it’s leaking a bit
Just keep any eye on temperature gauge. Along as it never gets above half way no concern. MAKE SURE COOLING SYSTEM IS FULL. DO NOT GUESS. DYOR I bare no responsibility on that comment.
@@thepartsfactory4239 how do I check if cooling system is full on my dash menu? , thanks really answered my question
@@thepartsfactory4239 so what it leaks is coolant right ?
@@thepartsfactory4239 thanks man I really like your video ignore all the negative comments.
Don't wait for the overheating idiot light. Just raise the hood and look at the coolant reservoir right behind the latch. If there is any red fluid visible you will be okay. Check often and top off to the middle seam. Use only the red premix or distilled water in a pinch. I live in Phoenix and have no problems even in the summer.
Helpful video, irritating background music!
Agreed! Learnt from our mistakes. From now on, NO music! Thanks
@@thepartsfactory4239 just get the background music volume lower so we can better hear you speaking
@@thepartsfactory4239 I like fixing Chevy's so simple to work on but with any repairs you need read and ask questions. #chevycruze
Thank you for the demo
I have a Chevy Cruze 1.8L Eco Tech Manual 6 Speed transmission.
My thermostat housing seal started to leak (coolant fluid) after the thermostat throttle pressure (intake heater line) failed. I replaced the thermostat housing, but now the oil cooler pipe is leaking coolant. I replaced the o-ring and still is leaking, I think it needs a thermometer gasket?
I will be replacing the throttle pressure intake heater line that runs from thermostat housing to the intake.
#chevycruze #chevy #cruze
How'd it go?
the system will remove the air pokets from the coolant by itself?
Great video thanks 👍
Thanks for the video!!👍🏻
Music louder than the instruction? Why?
Can the bottom part of the clip brake off? I cant get mine to lock into place.
Yes it can. Take a look at your new pipe. See the very tip of the the male end of the pipe? The old peice will be stuck in your housing. Remove with pliers
The Parts Factory do we need to empty the coolant before changing it?
@@vikramjeetsingh9493 ... good question 👍 .... ??
@@vikramjeetsingh9493 no no
Could you just replace the O-ring where it attaches to the thermostat housing?
My thermostat housing failed, due to the intake throttle pressure heater line. There is also a return line on the throttle intake housing that feeds back to the coolant reservoir. The brake booster cylinder also has a coolant pressure heater line. #chevycruze #chevy #cruze
THANK YOU!!!!
Tip: That clip tab pulls straight out. Dont pry it
So where your butterfly clips are I have mine secured but it’s now leaking from there what would be the next step to fix
Is there a way to replace the plastic connector if that's the part that is broken without replacing the entire hose?
Best the replace the entire hose. Super easy to do.. and cheap!
I ask because I already have the replacement fitting and the hose is perfectly fine. It's just the clip on the plastic fitting that broke. So it pops out occasionally. So is there a way ? Lol
@@knimar0287 ahhh don't you just love when they don't answer you questions.
@@knimar0287 Did you ever find out where to get that plastic connector? Or even the entire hose with connector? just broke that little plastic piece changing out my thermostat housing...
Hi
I need this pipe for my barina Australia model . What is the name of this pipe . After few months I need to change this
Mine melted ra couple inches towards the back of the fitting? Any idea why ?
My easy piece that’s suppose to just click in that you did second... it won’t just click in, any ideas what’s wrong ?
Wrong! Do NOT use a screwdriver to pry up on the clip like he did, the clip might break or in his case, the neck below the o-ring will break (see the o-ring sitting on top inside the housing tube after he removed the fitting?) .. There is a tab on top of the clip to put the screwdriver in to pull the clip off the fitting.. When mounting, make sure o-ring is on the neck and push the fitting in the hole first, then slide the clip on the groves until it locks
If you're removing this hose, its broken already.
@@thepartsfactory4239 Wrong again.. I had to remove mine because my thermostat housing assembly needed to be replaced (due to hairline cracks) and there was nothing wrong with the throttle body heating pipe (tube).. If you remove it like you did prying it sideways with the screwdriver, you will break the lower portion of the neck.
@ecarroll3723 Mate, stop with the condescending behaviour. 🤚🏽 you are absolutely able to use a flat had screw driver to assist to remove that clip. Yes if its seen some significant wear and tear in the form of heat cycles it may break. Take your pathetic attitude elsewhere 🤡🤡
He is not condescending, he’s just telling you how it is. Everybody can get it wrong, and we learn from our mistakes. You should take this video down, because you are basically showing people how to break the fitting. It’s in 2 parts, and the part that clips in simply pulls out towards the front, no prying necessary.
music kills, I was cleaning my expansion bottle when filled it in I noticed leaking on this pipe , while finding a way to stop the leak , I cracked the pipe into 2 pieces, I went to pick up the fuel hose 6mm for a temp fixed , all was good until when I remove the sensor part to insert the fuel hose, it cracked into pieces where I can not even hold with a clamp, I have ordered new one, but me needing a car for work, I have tried to hold it with a clamp hopeful there is no heat pressure in this hose pipe because , I really need my car this week
what is the name of this part and its part number? Thank you
after 5 days from changing this part, the car throws P0605 code , Control Module Programming Read Only Memory Performance, any ideas?
This code isn't related to this part... memory usually means history code... clear it should stay away
Would that cracked hose cause a p0597 code to come up
No it wouldn't. Sounds like need new electrical thermostat
Turn off the damn music so we can here.
What is the music for?
What model cruze is this
This was 2007-2015 1.8L
I’m having a hard time getting the butterfly clips to pop into place on the fitted hose. Coolant is leaking out the top
Make sure there is no snapped of bits from the last pipe. Ive had it where you try and push dowm but because there is left over peices it will not clip in.
Great video, but could not hear a WORD you where saying.!
Okay so my throttle body heater inlet broke and I’m trying to fix it. Can anyone tell me the purpose or function of this?
Just noticed that mine broke as well on my 2014 Chevy Cruze when I started to smell antifreeze/coolant; checked and by the elbow it has a leak. Took me forever to find what this piece is called!!!
Music is way louder than your vocals can barely hear what you’re saying
Very appreciative of your effort to make a vid, however
- the music, great you've said its banished
- the lighting .. why film in a dark workshop ? Park the car so that SUNLIGHT shines in from the font
+ your work light isn't constantly illuminating the area the camera is focused on, I'd suggest a Dewalt battery spotlight for the camera guy to hold & manouvre.
- & the camera operator needs to focus both in and out with multiple angles .... preferably without your hands in the way.
But again .... I AM APPRECIATIVE of your efforts.
I've subscribed 👍to your channel bcaus:
My daughter has just bought a 2016 Sportswagon Cruze ... which I've discovered has oil from valves leaking and pooling above between spark plug & coil (watched that vid 👍) any chance of a vid on rectifying the valve seal/rocker cover gasket/baskets ???
Your background music is too loud making it difficult to hear what you are saying
you dont need that noisy music
Back ground noise is way to loud
You shouldn’t have background music. Your drowning yourself out
Older Video. Am aware. Thanks for your input though.
Just some feedback mate you need to piss that background music off it makes it very hard to hear what your saying and it’s just annoying
Music is a little too loud we can’t hear what you’re saying so please redo the video with no music
Yes this was a long time ago. You're right we should re do. Thanks
Sorry, but whoever decided that elevator music would enhance the quality of your video should get the dummy dust kicked out of him. I couldn’t stand half of it.
5 year old video
Music way too loud, would be better without all together
Lose the music.i couldnt even understand what you were saying
I can’t hear the bloke
Music too loud can't hear what you're saying
I can't hear the music with all the talking! SMH 🤦 #turnthemusicdown
music completely ruined this. ugh
Fixed new vids
Music lmmfao
Nobody came here for gay qualude music. Came for mechanical instruction. Please repost
what's with the LOAD horrible music?????
Kill the music
The fucking music is horrible.
Ruined the video with music : (
The music is TOO LOUD AND DISTRACTING. terrible video
Always learning! Never putting others down though!
Can barely hear you over crappy music
New videos no music. This was one of our first ha ha
Cant hear you over the music... like at all.