Top End (Cylinder & Head) Assembly - Zeda 2 Stroke Bicycle Engines - Motorized Bike Jug Installation

Поділитися
Вставка
  • Опубліковано 23 гру 2024

КОМЕНТАРІ •

  • @michaelluciano7774
    @michaelluciano7774 2 роки тому +5

    Dude I enjoy your channel. I absolutely love 2 stroke engines in general, I ran a chainsaw for a living during the winter months. Though I have a Chevy Silverado, I regularly ride my motorcycle bicycle to town and back.

  • @paulchoate
    @paulchoate 17 днів тому

    Thanks that's just what I did my concern is the arrow on should it face the intake ?

  • @thirdeyesurvivor3886
    @thirdeyesurvivor3886 2 роки тому +3

    Thank you so much for explaining it properly.

  • @cliffordbradford3257
    @cliffordbradford3257 2 роки тому +2

    I like to install 1 of the clips before hand that way 1 clip is in there to hold the wristpin in place when you push it all the way in

  • @nathanael5606
    @nathanael5606 10 місяців тому +1

    My engine came with some metal shavings in the crank. I had to clean them out, but it should be good now. Cheers

  • @elithomasofficial7733
    @elithomasofficial7733 2 роки тому +1

    I just ordered my new engine from you guys

  • @Westhelockpicker
    @Westhelockpicker Рік тому

    Since these are supposed to be triple 40 then they should all have a high hole piston correct? After mine is broke in I have a ported cylinder to install and while it's apart I was going to add a windowed piston and reed valve but I can't remember what piston it was when I put it together

    • @BicycleEngines
      @BicycleEngines  Рік тому

      Yes that is correct.

    • @danajett
      @danajett Рік тому

      I'm having major problems with piston clips finally after going through losing 5 of them I have them in but now my problem is 1side is in further than the other side and i think that's a problem am I correct?

    • @Westhelockpicker
      @Westhelockpicker Рік тому

      @@danajett if you look there is a groove they go in

  • @worscohli
    @worscohli 6 місяців тому

    How do you take the engine apart if you ordered pre-assembled, but want to grease the piston to be sure? Can u just pull it off? or will tht break the piston rings?

    • @BicycleEngines
      @BicycleEngines  6 місяців тому

      You can remove the top end from the bottom end as many times as needed for repair or gasket change out. You will just have to torque the acron nuts again putting it back together. We always grease the piston before assembling it here in our warehouse. Just becareful you can tear the gasket by taking it apart. Here is the instructions from our website if you want them. www.bicycle-engines.com/product_images/uploaded_images/Cylinder-Assembly-Instructions.pdf

  • @JimmyEast-m3z
    @JimmyEast-m3z 5 місяців тому

    Need help put new piston in 2 stroke piston hits the cylinder cap and stops what am i doing wrong.

    • @BicycleEngines
      @BicycleEngines  5 місяців тому

      There are two main types of piston a low hole and a high hole.
      If you try to use the wrong combination of connecting rod such as a long connecting rod with a short full distance it's going to hit the head. Confirm you have the correct piston with the correct bottom end and if still the problem persists maybe check the bottom gaskets

  • @lancebarton4361
    @lancebarton4361 Рік тому +1

    Does it matter which way the windows are facing o the piston

    • @BicycleEngines
      @BicycleEngines  Рік тому +3

      Yes, the arrow on top of the piston has to face the exhaust.

  • @chappyvibing6949
    @chappyvibing6949 4 місяці тому

    My cylinder isn’t sitting all the way down on the engine and I’m not sure why, please help me

  • @larryshaver3568
    @larryshaver3568 Рік тому

    couldn't you slide the first ring on from the bottom? turning the piston upside down first

  • @MonirKhan-fw5pp
    @MonirKhan-fw5pp 2 роки тому +1

    Sir, can you help me to know all fundamental of engine kit of cycle?

  • @Anthonywhite-w2t
    @Anthonywhite-w2t Рік тому

    Question if I have to attach my chain and bearing plus a small cylinder rod falls out how do I reinstall it?

    • @BicycleEngines
      @BicycleEngines  Рік тому

      Good question! The ball goes in first then the pin. I add some grease while I'm in there. No trick just slides in. It goes in the little hole in middle of the drive gear. Just in case you are not sure.

    • @Anthonywhite-w2t
      @Anthonywhite-w2t Рік тому

      @BicycleEngines okay and best way to get the bike warmed up before some steep hills would be if you have any tips

  • @natestockman5429
    @natestockman5429 2 роки тому +1

    Do you guys sell the engine assembly mount?

    • @BicycleEngines
      @BicycleEngines  2 роки тому +1

      We have the front engine mount for a large downtube. www.bicycle-engines.com/front-engine-mount-for-large-downtube/ that is the only thing we currently have.

  • @adventureguy4119
    @adventureguy4119 2 роки тому +1

    So fhe ring openings point directly to intake

  • @slothzombi307
    @slothzombi307 7 місяців тому

    Hopefully the cylinder and head don't come in a box bouncing and clanging around together like you showed.

  • @boydjensen3161
    @boydjensen3161 2 роки тому

    Can you buy that black engine assembly stand?

  • @GhanjaKhan1380
    @GhanjaKhan1380 2 роки тому

    I can't attach my piston, it's pre installed, how do I get it out without damaging?

    • @BicycleEngines
      @BicycleEngines  2 роки тому

      Can you explain more on what you are wanting to do? The Piston should come out with out damage. Are you talking about the cylinder?

    • @GhanjaKhan1380
      @GhanjaKhan1380 2 роки тому

      @@BicycleEngines I got it out, it was loosely fitted inside it.

    • @GhanjaKhan1380
      @GhanjaKhan1380 2 роки тому

      @@BicycleEngines however I am missing a black washer would I be able to use a regular washer, it sits under the head

  • @bigboy-no2zo
    @bigboy-no2zo 2 роки тому

    Is there a size difference in the two Rings?

  • @brucefoskey8501
    @brucefoskey8501 2 роки тому

    Can. It be. Brought. Altogether. With the bike

  • @JMB676
    @JMB676 2 роки тому

    Is this where you are now Alex?

  • @leonardarola
    @leonardarola 2 роки тому

    Enjoying it. Subbed.

  • @MarkBroll-ic4qg
    @MarkBroll-ic4qg 6 місяців тому

    Great

  • @cesarfarias4219
    @cesarfarias4219 Рік тому

    Bom

  • @wrongturnmotorizedbikes4604
    @wrongturnmotorizedbikes4604 2 роки тому +2

    Scammers who steal your money and don't send what you pay for. They owe me for 2 items they refuse to send me I paid for. Won't respond to email or calls. Legal action had been taken against these scammers

    • @BicycleEngines
      @BicycleEngines  2 роки тому +1

      We have no information from you on what you are suggesting. No voicemails, No emails. So, tell me your name and I will look into your issue.

    • @rez372
      @rez372 2 роки тому +2

      @@BicycleEngines you guys are great forgot to send me a spark plug as soon as I brought the problem to you, you fixed it

  • @charlesyates6687
    @charlesyates6687 2 роки тому

    Chuck's motorized bicycle repairs
    Tampa florida.

  • @loganwilson5457
    @loganwilson5457 2 роки тому

    Don't waste your time, go ahead and put it back in the box and throw it in the dumpster, it a piece of crap.

    • @joshapples88
      @joshapples88 Рік тому

      Why do you say that ? I know it may not be the best quality but why do people swear by them?

    • @MartinSage
      @MartinSage 7 місяців тому

      Where do you buy your 2stroke motors, sir?