Thanks for the video..it fixed my old ‘97 Ram. I changed out all the other sensors like you had done with no luck also. The issue had been getting worse for a long time. Finally fixed..thanks!
what o2s did you use? i had a high voltage code, fixed the harness wiring but its still idling rough, it has ntk 02 sensors in the truck but still running bad.
I used Bosch, if you had a high voltage code that means it’s running rich, I would look into the causes for that if the sensor you put in is new, check the plugs wires, check for vacuum leak etc.
Ntk sucks in my opinion had new distriutor cap/rotor wires and I believe spark plugs all went bad in a month and when I went to take the plug wires off the core ripped right out even with silicon grease inside
my truck runs great without any for issues for about an hour then starts to sputter and stall at low rpms ,was yours doing this or was it running rough from the start?
My truck has this issue as well but mine cranks starts and falls on its face if I feather the gas it’ll stay running but runs like crap when I release the gas it dies sometimes idles at 300 rpm’s
Did your truck cut out and back fire and miss too my truck has that hissing and idles like crap like it has a big cam and cuts out then it will run fine for awhile
I changed the IAC. It started right up and stay running drove away from home for 30 minutes and it stopped when I slow down and pulled into McDonald's. Now it's doing the same won't stay running without accelerating could drive with 2 feet😮💨 someone help
Mine has no light but it's Smooth but when ideling it's just quick miss like 1 cylender .it's smooth then bam then smooth agian ant even close to quiting. I bet that's it man 97 318 gonna try it.good vido
My dodge use to stall at stop lights or stop signs as it got worse it started to die when i change gears.. anytime you can think of? Im tired of spending way to much money that i dont have
I had that issue taking off my exhaust I had the best luck cleaning the o2 sensors and using a little seafoam if I were you get a decent code reader and start looking at live data
@@Tylerking313 dang that’s awesome, I was worried if I deleted my cat that it’ll throw codes. I have a rough idle as well and occasionally throws codes for Evap leak or running rich in bank 1, was planning on deleting the cat and seeing if that solves my problems, I’ve replaced a bunch of stuff and still nothing has worked
Thanks for the video..it fixed my old ‘97 Ram. I changed out all the other sensors like you had done with no luck also. The issue had been getting worse for a long time. Finally fixed..thanks!
Thank you sir. Ima try this. Cause I’ve been throwing parts at mine and seeing if something sticks.
Yes exactly what happened with me I tried plugs distributor and cap and ignition coil
nice! I grabbed some NTK's
I had the same problem, my fix was fuel pump,low pressure.👍
Rockauto has good parts.I’m up in Canada and it’s still cheaper to order from them.Cheers
What intake manifold is that? It’s not the barrel one
what o2s did you use? i had a high voltage code, fixed the harness wiring but its still idling rough, it has ntk 02 sensors in the truck but still running bad.
I used Bosch, if you had a high voltage code that means it’s running rich, I would look into the causes for that if the sensor you put in is new, check the plugs wires, check for vacuum leak etc.
Ntk sucks in my opinion had new distriutor cap/rotor wires and I believe spark plugs all went bad in a month and when I went to take the plug wires off the core ripped right out even with silicon grease inside
my truck runs great without any for issues for about an hour then starts to sputter and stall at low rpms ,was yours doing this or was it running rough from the start?
Did you fix it?
My truck has this issue as well but mine cranks starts and falls on its face if I feather the gas it’ll stay running but runs like crap when I release the gas it dies sometimes idles at 300 rpm’s
My first guess would be check your fuel rail pressure or check if you have the firing order correct on the distributor
Did your truck cut out and back fire and miss too my truck has that hissing and idles like crap like it has a big cam and cuts out then it will run fine for awhile
It would only idle rough and hiss but when I tapped the throttle it would go away
@Tyler King that's what mine does too but sometimes it stumbles and acts funny then it runs fine
So did it do it when you first started the truck or only after it warmed up a bit and went into closed loop?
@@Indeewoods it would be completely random
The hissing is usually iac valve..hope this helps
I changed the IAC. It started right up and stay running drove away from home for 30 minutes and it stopped when I slow down and pulled into McDonald's. Now it's doing the same won't stay running without accelerating could drive with 2 feet😮💨 someone help
Did you fix it?
Mine has no light but it's Smooth but when ideling it's just quick miss like 1 cylender .it's smooth then bam then smooth agian ant even close to quiting. I bet that's it man 97 318 gonna try it.good vido
Any luck? I just started having the same symptoms you described but on cylinder 4 instead
What are the OE brand 02 sensors?
Probably ntk or something equivalent, if not that a mopar sensor from the dealer if you can still get them
My dodge use to stall at stop lights or stop signs as it got worse it started to die when i change gears.. anytime you can think of? Im tired of spending way to much money that i dont have
I had that issue taking off my exhaust I had the best luck cleaning the o2 sensors and using a little seafoam if I were you get a decent code reader and start looking at live data
Do the o2 sensors read fine with out the cat? Tried everything on mine, I’m assuming my cat is clogged as well!
Yes it’s been catless for years and no check engine light
@@Tylerking313 dang that’s awesome, I was worried if I deleted my cat that it’ll throw codes. I have a rough idle as well and occasionally throws codes for Evap leak or running rich in bank 1, was planning on deleting the cat and seeing if that solves my problems, I’ve replaced a bunch of stuff and still nothing has worked
@@warnerdaniel4241 deleting the cat will only help you haha it will sound better and more hp, hope you figure it out!