How to Install Aftermarket Foglights 01-05 Honda Civic
Вставка
- Опубліковано 23 сер 2024
- Buy Now!
New Fog Light Kit from 1AAuto.com 1aau.to/ia/1ALF...
In this video, 1A Auto shows you how to custom fit aftermarket fog lights into a stock bumper using the 01, 02, 03, 04, 05, Honda Civic as an example.
🔧 List of tools used:
• 10mm Socket 1aau.to/ot3/1AX...
• Plastic Fastener Remover 1aau.to/oN/1AXA...
• Pliers
• Wire Cutters
• Ratchet 1aau.to/oC8/1AX...
• Socket Extensions 1aau.to/oxq/1AX...
• 1/8 Inch Drill Bit 1aau.to/oF/1AXA...
• Drill
• Marker / Writing Utensil
• Wire Ties
• Reciprocating Saw
• Utility Knife 1aau.to/obK/1AX...
For More Info visit us at 1aau.to/h/75/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Please read my comment🙏
This is the most complete fog light tutorial for the 7th Gen on UA-cam. If I decide to do this, I'm going with 1A Auto. 👍
+Cinca0989 Thanks for checking us out!
This is a great tutorial! I used this as a guide to install my own fog lights on a 2002 civic. The only thing I did differently is to wire the switch on the left of the steering column. There’s another pop out panel there as well and it feels like more of a natural location to have lighting controls. I put my seat heater switches where you guys put the switch :) thanks for the great videos!
OMG how did you go about installing the heated seats?
That air filter doesn't look so good.
That employee did a great job.
💯 YOU GUYS HAVE LITERALLY HELPED ME AND A MILLION OTHER PEOPLE WITH YOUR HOW TO VIDEOS.... THANK YOU FROM ME AND THE CAR NATION
Sometimes a cheap relay can fry the entire harness ...
This is the best video I've came across for fog lights installation. You made it easy
I have never seen the center console taken apart like. I have an 04 civic EX sedan that when I bought it, my rear cup holder is broken out. IF you guys could do a breakdown of the complete console that would be fucking amazing
If that switch were recessed just a LITTLE bit more, it would look convincingly OEM. I'm looking to buy an 04 Civic and if I get it, I'm definitely buying this kit!
hi 1A auto i just followed this tutorial and im pleased with the little details that are added here, i would like to offer little tip into making this that much cleaner of a install
i completed this install by tucking the wires into the front crash bar instead of running them ontop of the radiator support ,i was able to get the fog light wires coming out of each side of the crash bar and then running the relay and power wire thru the crash bar coming out of the passenger side hole same as fog light wire i ran.. the whole harness is in the crashbar, i wrapped up the whole crashbar with wide scotch tape just like the piece of tape thats holding up the foam on front of the crash bar i just wrapped it all the way around so the harness cant fall out into the front of the radiator/condenser , now with the ground wire thats on the driverside of the harness i was able to find a bolt just to the left of the driver side light like 2 inches away from it so i tapped the ground into it there, power wire/relay/switchwire was ran the thru same hole next to fender and ran to the fuse box just as instructed, the rest of the installation was exactly the same way( power wire tapping into cigarette lighter) but instead of running the switch to the middle console with cigarette lighter i ran it thru to the mirror/cruise control assembly on the left side of the steering wheel.
thanks to this tutorial video you made i was able to get my fog lights installed on my 2004 honda civic GX and with the little tips i put above the harness and lights were installed super clean all tucked in like a pro and i cant be happier with my install, thanks again 1A Auto you made my day !!!!
+Tony Urena Thanks for the feedback and for checking us out!
I love this page
As always... a top notch tutorial. You guys are my go to. Thank you!
Nice and Simple just did mine and it looks 👌😮💨🔥
THANK YOU!!! 1A Auto
Good video. Only I think Im gonna add a rocker switch instead of running that positive wire to that power source
So bumper removal is required,might as well get a now one ,mine is kind of mess up😅
Wow. I want to do this for my 2005 Honda Civic Coupe Dx.
The switch for my fog light won’t stay in. It just falls out the front and I can’t understand how it mounts in. Any ideas?
Great to see Mike & Tony again!
+mrexecutive1 Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
where can i find that double barrel connector? Great vid👍🏾
Jan 22 y me arrepiento de no haber encontrado este video antes, que excelente manera de explicar, un sub más
Excellent presentation with clear and concise explanations. It really is that easy. Thanks so much!
If you go straight and not all around the radiator you shouldn't have to use extra wire! But good explanation! Thanks
Could you power a small light bar using the fuse box power source
I installed these as in the video and then I notice my led light strips connected to the (cigarette lighter) started to flicker not on and off but like pulsing. Then I notice my dome interior lights did the same and also my trunk light. Any ideas what could be wrong?
i had pulsing headlights and interior lights on my 03 ex and for a while i had been assuming it was an alternator issue, sure enough i tested my alternator and it wasn’t putting out the proper voltage(14-14.2ish) to compensate and charge the battery, replaced the alternator solved the issue. Might not be the same case for you but i figured i might as well share and see if it could help
I followed these instructions to install fog lights and I have a problem now with my civic horn. It stopped working after installing fog lights. Any ideas what might have happened ?
+Nando Sp_23 Have you checked the wiring and fuses?
@@1AAuto it turns out the horn cable had a lot of tension on it, all i did was make it loose and it worked. Thank you guys
how do i make them turn off automatically when my high beams turn on? i can’t pass inspection because they are a completely different circuit.
Any plans to change out that upper tie bar ground? Looks like a horse's tail.
How much would this be if I got it done professionally?
Great video
Hi can you do video for honda CR-V 2016 fog light aftermarket thanks
+hussam juneed We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1AAuto.com
It is basically the same the only difference would be the location of the light and switch.
I did the positive wire to the positive cigarette wire and it works but when I plugged in my charger to the cigarette lighter with the fog lights on it blew the fuse. This was on a 2003 Honda Element any idea why it did that? I have it working now just not using the cigarette lighter until I can figure out why it does that any help would be appreciated
the positive red wire he connect to the cigarrete is the yellow, he just added extension on the yellow wire
@@jeremycarldaigo8768 cigarette lighter fuse keeps blowing with fog lights tapped into it so I took it off no problems ever since. But now I need to find a accessory wire all I can think of is my radio accessory wire but I have 2 amps tapped into it already I'm wondering if I put the fog lights also if it will blow aswell I don't know
do you have a video for a 01 hyundai elantra
HI, WHAT KIND OF POWERFLOW IS .. PLEASE...
Does anybody know where I can find that red double barrel connector
Any videos for a 2003 Honda Accord
I purchased your fog light kit from the website but found out that the fog light switch doesnt fit into the center like in the installation video
+Elisio Lopez We would be more than happy to work with you on this. Can you please contact us at 888-844-3393 or service@1aauto.com and we can help you directly. Thank you!
Elisio Lopez What did they tell you when you called? i have the same issue
1A Auto Parts I have a stock 2005 civic bumper the fog light holes are different than these ones, similar but different will they work?
+blue-Chaosis Thanks for watching! The fog lights in this video are meant to go on models that did not come with fog lights originally from factory. These will not work for your application if you have factory fog lights.
Would this work on a 2003 Acura RSX Type S?
Can you work on my civic
When he says that the red cable isn’t far enough and connects to the black???? So I gotta get a instention or what???
Does the fog lights come with everything as far as wiring?
I believe so, yes
David Juarez It does, installed mine today
+David Juarez Yes, the wiring is included. Thanks for checking us out!
There are much easier and more effective/safer and professional ways to wire things up to a car rather than splicing into already existing components.
There are fusible links that go directly into the fuse panel so your wiring is all clean and together, plus it would be fused so if something blows there would be no issues.
I don’t understand the metal clips.. one end is bigger than the other and won’t go all the way thru.. can you explain this?
Put the clip on over the plastics. Put the screw through the clip. The bottom of the screw needs to go through the small end of the clip.
Usefullllll !
My bumper won’t come off is it the same procedure for the sedan ?
Where is your bumper getting stuck?
What if you have a Acc wire?
Does this kit come with that extension wire you had connected to the yellow wire? If not, where would I be able to buy that wire and what is it called?
Comes with it
Any reason why my switch fits all ugly?
+Matthew Cisneros Thank you for checking us out. You may need to re adjust this so it fits to your liking.
1A Auto Parts Regardless of how i put the switch in, it still pops forward out of the socket... Also the kit didn’t come with any screws to secure the housings onto the bumper. What size was used in this video?
Awesome work, if you want to see other great 12 volt videos please check out our page.
+Crux Interfacing Solutions Thanks for checking us out! 1AAuto.com