7 Best And WEIRDEST Ways To FIND A STUD (#7 is the strangest!)
Вставка
- Опубліковано 4 січ 2020
- Check Out Our FREE GUIDE: 25 Must-Have Carpentry Tools...Under $25 Each!
www.thehonestcarpenter.com/
AFFILIATE LINKS FOR THIS VIDEO:
15-Pack Rare Earth Disc Magnets:
amzn.to/3bW21IA
Phillips Norelco Travel Razor:
amzn.to/3e64Dq5
Estwing 16 oz. Hammer:
amzn.to/3sOC5oX
Steel Wool 12-Pad Super Fine:
amzn.to/3bg5cf1
(These are affiliate links. When you shop through these links, we receive a small commission at NO EXTRA CHARGE TO YOU. We greatly appreciate the support!)
FOLLOW US ON INSTAGRAM:
/ thehonestcarpenter
FOLLOW US ON LINKEDIN:
/ thehonestcarpenter
THERE ARE ACTUALLY 8 METHODS IN THIS VIDEO due to a small editing fiasco. MORE IS ALWAYS BETTER THOUGH, RIGHT?! :)
Who needs a studfinder? These 8 ways to find a stud are the best and the weirdest! Here at The Honest Carpenter, we personally think #3 is the best, but #7 is the weirdest method that REALLY WORKS!!
BE SURE TO CHECK OUT OUR OTHER VIDEOS:
World's Greatest Tool Belt:
• THIS IS THE GREATEST T...
Chisel Vs. Big Screwdriver:
• CHISEL VS. BIG SCREWDR...
Don't Use A Ball Catch Latch!:
• DON’T USE A BALL CATCH...
There are a lot of ways to find a stud. But these are the ones that I use as a professional carpenter, plus a couple weird ones thrown in!
8 WAYS TO FIND A STUD:
1: The Knocking Method: Use a 16 oz. hammer wrapped in a wash cloth to knock on the wall. The space between studs will make a low pitch sound. The point on studs will make a higher pitch sound.
2: The Electric Razor Method: Battery-powered electric razors also work well. Press them to the wall and move the sideways. Vibrations will make a higher-pitched sound on studs.
3: Use Magnets! : This is by far the best method. I use rare earth neodymium magnets to find screw heads where drywall is attached to studs.
4: Look For Outlets And Lightswitches: These electrical boxes are almost always mounted to studs. Just knock on the wall to either side of the outlet.
5: Look For Nails In Trim: Carpenters mostly try to nail trim to studs for better support. Look for trim nails that painters did not effectively hide, then test the wall with a magnet.
6. Look For Popped Screws: Drywall screws that don't get set deeply enough sometimes pop their mud patches. Use a bright light held near the wall to make them stand out visibly.
QUICK TIP: Remember that studs are spaced 16" on-center, except in some newer homes where they are spaced 24" on-center.
6 (b): The Coathanger Method: Straighten a wire coathanger, then put a crook partway down. Punch a dime-sized hole in the wall. Feel the coathanger through and swing it around until it hits a stud. Pull the coathanger out at that angle and hold it up to the hole in the wall. You'll be able to see the approximate stud location.
#7: The Steel Wool Method: Rub two pads of steel wool together near the wall. The friction between metal surfaces will produce a small electrical charge. Filaments with this charge will fall down the wall and get stuck on screw heads magnetically. These are your stud locations.
Thanks for watching! PLEASE BE SURE TO LIKE AND SUBSCRIBE FOR MORE VIDEOS!
Also, be sure to visit us at The Honest Carpenter Website:
www.thehonestcarpenter.com - Навчання та стиль
THERE ARE ACTUALLY 8 METHODS IN THIS VIDEO! Just had a small fiasco in editing. But more is always better right?! :)
AMAZING a magnet, razor, coathanger hahaha you really included ALL methodes one can conjure up applause , slowly bowing and hemicycling my baseball cap
Some new info here for a grizzled carpenter. Don't know bout the coathanger, but the steel wool trick is pretty ingenious and just might come in handy.
I'm sure you're aware of the following, but I didn't hear you mention it in your video.
I use electrical switches/outlets to find studs all the time, but ya gotta keep in mind the possibility that the box isn't mounted directly to a stud.1:47 Shows an electrical box attached to 2 2x4 spacers/blocking attached to a stud. Surprised you didn't mention it when you filmed this very possibility. Of course the 2x4 spacers/blocking can be mounted to by whatever you're attaching to the wall, but only right near the switch/outlet.
Sometimes horizontal blocking near the top of bottom cabinets or near the bottom of top cabinets can masquerade as studs. Same is true for plumbing blocking. Both situations are similar to switch/outlet blocking in that this blocking can be mounted to but only right near the blocking.
I use some of the ways you describe to find a stud, but I always confirm stud location by what I call the redneck stud finder: hammer a nail into the wall in the location of whatever I'm mounting so the holes will be covered. Unless I framed the wall and am confident in the stud spacing, I always double the location of every stud this way.
Keep up the good work. Stay safe out there.
What if my walls don't have studs?
stud finders act like the whole wall is one giant stud, magnets don't detect any nails/screws, tapping produces no results... I'm ready to drill a hole and try shoving an endoscope into the wall.
Excellent: particularly the steel wool method.
Neat tricks but we need to watch out for electric cables. We don't know if they run all over the wall. 😬🤔
This is a great example of why UA-cam has value.
Sometimes
Or you can do like my ex tenant did and open up holes with a hammer and nail until you find a stud. Just for kicks I counted 600 holes in the walls of a 1.700 sq. foot house.
Yes yes yes !!!!!!!!!!!!!!
Indeed. And I want to believe that the eerie timing of the video's appearance in my playlist is purely down to the baader meinhof effect... 😳
right! this is why I always tell people "I went to UA-cam University" 🎓
For the coat hanger trick: bend it in a "U" shape with both legs the same length, when the leg inside the wall hits the stud, the outside leg will show you exactly where it is.
😮👏🏼👏🏼👏🏼
Very smart👏👍
Awesome tip. Thanks for sharing
This is also a very good tip! Thanks!
Solid tip
This has got to be the best video I have seen in a long time. Short and effective, packed with loads of useful information. Thanks
Just walked around the house finding studs with a magnet. I feel so empowered. You have already help me fix a door lock and split trim in my sunroom. I now use the ladder extra bits but would love to learn how to roll up an electrical cord so it rolls out without being tangled. You are awesome.
ua-cam.com/video/cpuutP6Df84/v-deo.html
He is working with mic cable but extension cords coil the same for the same reason... the wires inside are twisted and want to coil naturally
ua-cam.com/video/EwaGcPmtTsQ/v-deo.html
I seen this method, won't go back to any other way. Over under, around the arm, throwing it on the floor in a pile, all of them produce nasty messes for me. This video shows how to do it mess free. Rolls up fast and unroll faster.
ua-cam.com/video/EwaGcPmtTsQ/v-deo.html
can't go wrong with this technique, and it's from a great channel. Might not be the best option for very short cables, but it will never tangle and you can actually unhook and hold onto the ends and throw the whole cable outwards where it will unravel in the air and impress your friends. Personally, I like having the two ends together so i can plug it into the wall and a tool/another extension cable and just walk away, letting it unravel as i go.
@@DavidSmith-rf5je absolutely. Hands down the best way, I made my comment before I realised it was the same video 😂
The Essential Craftsman channel shows some extension cord tips and much much more.
Magnets are a great idea. That steel wool trick is crazy. I've never seen that before.
Yeah, now am thinking of getting some.
Thank You for this video!
Currently hanging a very heavy cabinet and the disc magnet suggestion is awesome and also allows one to avoid the dryhole nails when selecting spots in the studs for pilot holes.
Best Regards!
I never thought of using magnets but I see it works! That is a great idea and I will certainly remember it.
Great tips. I have been nailing onto the wall with small nails all the way across the wall until i hot a stud and then marking it. I love the magnet method!
Thank you for giving clear concise and easy directions straight to the point
OMG! the magnet method works amazingly well. Stud finding has been a great source of frustration for me, especially in cases of irregular stud placement. Thanks so much for this video.
You’re welcome! Thanks for watching 🙂
I just used the magnet technique in a closet re-build. It worked like a charm! I also used the light to spot a few rogue screws. Thanks for the tips!
Thank you so much. The magnet technique saved my day. I was able to map a wall using magnets, outlets, light switches, and a stud finder. I was planning hanging floating bookshelves for a couple days, finding the the studs was vital. Thanks!
thank you so much for sharing! The magnet one is the best! The apartment I live in has studs that spread out unevenly... so this is a life-saver!
The magnet way seems to be the easiest way I never tried it but soon I'll give it a shot when I do some picture hanging..Thanks for the tips🙏🏻.
And you have done it again. Thanks for the awesome tips🎉
Very clever! I like the magnet idea, tip #3! Thank you for all the tips!
Wowzers Ethan, I thought I had used some "weird" ways to find a stud... I love the magnet way... ordering this today!
I really enjoyed watching and listening to your tips and tricks of the trade... thanks for sharing and especially caring how things are done and done right! Many Blessings
Funny but I always have a hard time trying to listen in to find the stud. I'm going to try the magnetic one. Thanks for helping!
These methods will help you find the screws attaching the board to the stud but ideally you need to "bracket" the found stud to find its centre. That screw may have only just caught the edge of the stud. Drive a finishing nail progressively to the side of the screw until it misses the stud. That will give you one edge of the stud. Do the same in the opposite direction for the other edge. It will usually be 1 1/2 inches.
Great video. I have to find some ceiling joists through a drywall ceiling, and I don't trust my Ryobi stud finder, as it's let me astray more than once. However, I just happen to have a pack of rare earth magnets, so as soon as I saw you do it. I grabbed the magnets from my desk and quickly walked to my nearest wall, and started sticking magnets up and down the wall. GENIUS idea! Now I don't even need to draw any lines or lay out lines of tape or anything, because I can just follow the straight line of magnets laid out on my ceiling. Thanks so much for this great tip.
This was awesome! Just used some thick little office magnets I had lyIng around, worked like a charm!
Good job, Ethan! Enjoyed this video, Thank you!
Top tip, good Sir! I've got a pa k of rare earth magnets in the garage. I've also got a stud finder that I got as a gift. The magnet seems a much more reliable method. Thanks for sharing
for a female that has to rely mainly on myself more so now, I apreciate your tips and and how you exsplain things thanks!!!!
your vids are incredibly well designed & packed with excellent content. Thk u.
All were super ideas. Thanks a lot. Nice, clear, and fast paced video...a great learning tool.
Great tips each and every one of them. One note, the light method of looking on a wall for screws/nails etc also works extremely well when looking for dropped hardware on the floor. The brighter/stronger the light the better.
One tip if you need to find multiple studs (like installing slat wall), is to cut a scrap piece of of wood 16" (or 24") long. Something small but still rigid, like a 1x2. Then once you find the first stud, just line it up and immediately know where the next one is. If you need it level, just duct tape a level on the top or bottom.
My grandfather said it the best ... you learn something new everyday
Omg this is so cool! I’m literally grinning like a kid in a candy store. Thanks for sharing.
These tips are amazing! MAGNETS! I never thought of magnets before. Thanks a ton for all of these videos, they are incredibly helpful.
The magnet trick was sage wisdom! Thanks !!!
Brilliant methods! Nicely done demo. Thank you.
Hey this is simply the best way, Thank you so much for sharing !
Clever Ideas! Thanks!
Thanks for the video, Ethan. As always there’s a wealth of useful info.
Loved the tips! Thanks!
Over 40 years, I have 5 stud finders including a magnet (lost it) & 2 that indicate electrical. Both of those are always alerting to electricity even when I put it on an interior door. So I use my oldest (with 3 vertical lights circa 1985) & my newest multi light finder. I bought the first finder but then I wanted to upgrade. After I moved in 2018, I was doing renos & the electrical warning in the finder was continuous so I bought an improved finder with a screen but it alerted to electricity where I knew there was no wire (back of a utility room wall). I exchanged the tool but still the same issue.The house has the foil backed vapor barrier fibreglass insulation (circa 1980) so I bought the newest finder. I love it.
Thank you so much. Helped me wall mount a TV
Great video! Stud finders have led me astray many times. Definitely buying this kind of magnets for all future stud finding.
Thanks Lyd!! They’ve never let me down 😁
Amazing tips, you are very knowledgeable.
Thank you
Wow, thank you very much for this valuable info.
Like I said you are way above average. Excellent class.
love that steel wool method, cant wait to try it
The magnet method worked for me, LIKE MAGIC! Thanks.
Cool info thanks! Getting ready to mount a big screen TV in a 1950's house with plaster walls. I need all the stud location help I can get!
Fabulous video! Thank you posting
Hi, watched your videos a lot, and still learing. As an old DIYer, this is the best informative video on utube, you sir just saved me 30$ more and a few headaches. From the bottom of my heart " THANK-YOU " keep these videos coming . Thanks again Wils 👍
Thank you, Wilson! 😄
Awesome stuff Ethan. Thanks.
Magnets are my go to! I bought a stud finder that actually uses magnets, just because it has more than one and makes lining things up a lil easier with built in level.
Great tips! Thanks
The magnet method is awesome. Thank you.
Super cool methods finding studs and people can pick which one they like. Cool, Thanks !
Sir, you just saved my life...thank you!!
I cannot believe what you just taught me. I just used the little magnets which I happened to have and found all the studs on the wall. I've been using this is zircon stud finder and it's so confusing and I don't trust it. Your method was spot on. Thank you so much.!!
Great stuff. Thank you. 😊 I'm not sure about number 6 with the coat-hanger, or no 7 with the steel wall, but the others are good. 👍👍👍
Wow really awesome I only knew of the coat hanger method
You rock!
Love your layout and your videos
The steel wool technique is really cool!
Nathan....always great videos...Thanks!
Thank you. Very useful videos
Love ur videos. Thanks!
I recently used several neodymium magnets to 'map' out the ceiling joists before I cut into it to remove a piece of drywall damaged by a roof leak. It was nice knowing where I was cutting so I got my best placement of the patch piece. Just stuck them to the nail heads. Also a plug here for my oscillating tool that made a neat job of cutting with only a shallow cut. No worries about hidden wires!
love these videos. this guy gets to it.
Another Bullseye for you Ethan. Good job ! 😉
Thanks Al! 😁
I've kept magnets of all types in my tool bag at all times. This saves time & trouble.
Genius . With good outro music👍
Great tips. Thanks for the video
I always have my pin-pointer from my metal detecting kit with me at work. It is also useful when trying to decide where hidden electrical wiring goes.
Great tips.
Will try a couple of these methods ‘til I find the stud!!
My little trick is more for commercial not home, but places like offices that have ceiling tiles, you can open the tile above where your going to mount, usually you can see the stud exposed above the ceiling grid, then follow it down.
Thank you!! Many great ideas!!! 💡
@The Honest Carpenter Thank you for teaching me a lot of tips! Wondering if the magnet trick would work over top of tile (ie. tiled over dry wall)?
that magnet trick, awesome!
That'sAwesome!ThankYou!
Thanks a tonn bud. I just fixed my closet without studd finder .
You are awesome. .’Many thanks
How fun with the steel will!
The magnet suggestion is Gold
Side lighting with a flashlight works for so many things, finding things dropped on a floor, any flaws on drywall/patch, checking flooring, body work on your car, hairs growing out of your head where they shouldn't be.
Magnets and steel wool. I’m going to try this just for fun. I’m enjoying your videos. Thank you..
Useful hints Thanks
I spent a crap-ton of money for a high-end stud sensor from a professional tool store (not a box store, and definitely not the dollar-store version of a tool store). Don't work worth a crap. Spent $20 for a 1"x1"x1" neodymium magnet. Works 100% every time.
The magnet trick is genius!
great vid man
Appreciate this one bruh🤙🏽🤙🏽
Good stuff, Maynard!
Thanks for being honest.
Great information. Thank you.
Oh finally a great UA-cam video!!
Greatest vid I've seen on this subject.
Awesome that magnet thing is going to come in handy 😱
I have to say, it is very rare for me to comment on channels and even rarer to subscribe but this is such practical and helpful information. Fantastic
Thank you, Kris! 😄
Thank you 😊I didn't know this and helped me tons. Thanks again.
I love this channel. I am binge watching these. Just marked my studs with magnets lol
GREAT video!
Ok now see, you've just gained 1 more subscriber!!! My boyfriend asked me to wait on him to hang the pictures my mom gave me. He's a handyman and works A LOT so I kinda understand, however at this point it's been about 2 1/2 weeks and my patients have run very thin. I actually have those same magnets already because I used them to keep my desk drawer shut. That steel wool trick dropped my jaw and the magnet turned on a light bulb. In short, The Honest Carpenter, DUDE YOU ROCK!!! Thank yo for sharing this. :-)
wow the steel wool one was one I never seen great thanks...
#7 Was really surprising. Will give it a try 🤙
I use a 180 pound magnet as sometimes in older homes the mud is so thick that the smaller magnets have a hard time locating the metal. Then hang several smaller magnets to mark off the studs position as the drywallers do not always hit dead center, especially on a drywall joint.