11 DRILLING TIPS AND TRICKS (And Mistakes To Avoid!)
Вставка
- Опубліковано 4 чер 2024
- Check Out Our FREE GUIDE: 25 Must-Have Carpentry Tools...Under $25 Each!
www.thehonestcarpenter.com/
AFFILIATE LINKS FOR THIS VIDEO:
Black & Decker 20V Drill Driver Combo (Amazing Price!):
amzn.to/2XgYQ4Q
Dewalt Drill Driver Combo:
amzn.to/3bZIzKO
Dewalt Titanium Drill Bit Set:
amzn.to/2PBJjOX
Bostal 60 Piece Drill Bit Set (Best Price!):
amzn.to/30fUHC2
(These are affiliate links. When you shop through these links, we receive a small commission at NO EXTRA CHARGE TO YOU. We greatly appreciate the support!)
FOLLOW US ON INSTAGRAM:
/ thehonestcarpenter
FOLLOW US ON LINKEDIN:
/ thehonestcarpenter
There’s more to drilling wood (and metal) than there seems to be. This video from The Honest Carpenter will teach you 11 of the most important drilling tips and tricks-along with a handful of mistakes to avoid!
For the purposes of this video, I’m just using an electric hand drill. BUT, many of these tips can apply to a drill press as well.
NOTE: Pre-drilling is always a good idea. Pre-drilling removes some of the wood that is in the way of the fastener you’re driving. This creates a channel or pocket for the fastener (screw or nail) to sit in. It also prevents splitting, and makes driving the screw easier.
Be sure to check out our other TOOL-RELATED VIDEOS:
9 BRAD NAIL MISTAKES:
• 9 BRAD NAIL MISTAKES (...
AWESOME ROLLING TABLE SAW CART:
• AWESOME ROLLING TABLE ...
6 STEP LADDER TRICKS AND SECRETS:
• 6 Step Ladder Tricks A...
MINI-HACKSAW-A VERY HANDY TOOL:
• Mini Hacksaw-A Very Ha...
11 DRILLING TIPS AND TRICKS HOW-TO:
1. Start with a punch-Pre-drilling will be much easier if you use an awl, or trim nail to punch a small depression where you want to drill. This helps guarantee very accurate drilling.
2. Don’t use too much force-A drill should cut effectively with only consistent, minor force. Skinny bits in particular will break if you push on them too hard.
3. Clear swarf out of flutes-“Swarf” is the waste wood or metal that is removed in the process of drilling. Swarf can clog the flutes of a twist drill bit, preventing the bit from cutting effectively. Be sure to back the drill out multiple times to prevent swarf clogging.
4. Step up sizes-Rather than use a lot of force, try starting with smaller drill bits, and working your way up to the size of hole that you need..
5. Use high speeds for drilling wood-Drill bits will work most effectively for drilling wood if you use high sheeds.
6. Use slow speeds for drilling metal-Conversely, slow speeds should be used for drilling metal, because metal material is removed in smalls scoops. If a bit is moving too fast, it will just skim along the surface of the material.
7. Tape to prevent splintering-To avoid tear out and splintering, try putting a piece of painters tape on the surface you’re drilling, and drill through it. The adhesive on the tape will stabilize wood grain below.
8. The “Eyeball” Method-To choose an appropriate drill bit size, hold the bit up to the fastener you’ll be using. You should be able to see the threads of the screw, but the shaft should be mostly hidden by the drill bit.
9. “Hogging Out” Material-If you don’t have a large enough drill bit, you can sometimes “hog out” the material with a smaller bit by working the bit back and forth through the hole. This will slowly widen the walls of the hole.
10. Don’t start drilling at an angle-Drill bits will wander badly when you begin drilling at an angle. So, instead, stand a drill bit up to start a hole, then tilt it down to finish drilling at an angle.
11. Use tape to set depth-Wrap a piece of tape around your drill bit to avoid over drilling. The tape will give you a visual indication of how deeply you would like to drill. This way, you can avoid punching through the backside of the material you’re drilling.
We hope you enjoyed the video! Be sure to visit us at The Honest Carpenter website:
thehonestcarpenter.com/
Check back in for more videos soon!
(Raleigh, Durham, Chapel Hill, Apex, Cary, Wake Forest--North Carolina) - Навчання та стиль
I've watched 5 videos today and I feel like I learned a years worth of information. Thank you.
Thanks for watching Corey! I’m really glad they’re helpful
You nailed it-there's so much helpful info in these short videos. I'm hooked.
I’m a carpenter. This man is the one to watch for real knowledge. I even enjoy the videos about things I’m already familiar with. A great ambassador for our profession.
And it has been a Year
Dude me too, this video blew my mind and made me realize how much I need to learn still.
I've been a woodworker for 50 years and in construction for 40. I probably didn't learn much from your video but I pretty much agree with everything you presented. Well done, excellent video.
Thank you, William! I appreciate that coming from someone of your experience level 🙂
Agreed. Speaking for myself I learned from experience and wish I had these passed to me years ago. So if you're a yungsta, pay attention. These tips will become second nature, but having them listed is very, very worthwhile.
Love your site. Helping people.. great tips
"I probably didn't learn much from your video"... the fact that you learned anything from this video means you are a bad woodworker. i'm not a wood worker and i learned nothing, every tip in this video is completely obvious to me and that makes you look bad im"h"o
@@pratwurschtgulasch6662 dont you understand english?
He did not learn anything, meaning he already knew what Ethan explained.
Additional metal drilling tips: Center punch where you want your hole to prevent wandering (same as you would for wood drilling). Add a drop of lubricating oil to the tip to cool and lubricate the cutting surface. After the hole is cut, use a larger bit spinning in reverse to slightly touch the hole to knock off sharp edges.
Solid advice! As a handy guy, I'm learning from all his vids and comments I read that just KNOWING what tradesmen do can take hours off a project by increasing precision or choosing a non-favorite tool.
Great video. How do I keep my drill level while drilling so that my drawer pulls won’t look crooked?
Number 1 sharp suitable drill bits, the angle of a wood bit at the tip is more acute.
2 suitable speed for material and bit type. Almost every woodworker I have ever seen, particularly on UA-cam uses spade/ flat bits way too slow, they work best sharp and fast.
3 Use suitable machine !!
Great video. One major tip I would add is to make sure you're using the right drill bit for the material. Bits for masonry vs wood vs metal and even ceramics make a huge difference.
When I use tape for depth drilling, I make a little flag. Then when I get to the proper depth the flag swipes away the sawdust and you know you are done. This helps eliminate drill depth creep (by pushing on the tape) if you are drilling multiple holes.
Whoa.....
🤯
Exactly!
And ... I like to draw a small skull and cross-bones on the tape flag.
This doesn't improve the drilling process any. However, it allows me to pretend that I am the captain of a pirate ship, and thus, my workday goes by much faster. I literally sail through my workdays. 🤪
Ive done this for alongtime when using a hilti hammer drill for drilling concrete.
I use a piece of red duct tape bc the depth measure on them move in time. Crappy design. so if any inspectors are walking through they see i have it set for depth. They just walk by bc they know im the sht. Lol
@@UserUser14880,
Awe man ... So, you're the one that invented "red tape" ?
Gran idea!
I knew several, but TOENAILING!!! Oh my goodness, that is gold for me! Starting practice tomorrow. Thanks!
Holy cow. What an unreal amount of useful info! You even crammed extra tips into several of the tips lol. Great stuff, thanks man, so glad to have recently found this channel
The lower speeds for metal vs higher ones for wood was indeed a good tip. I wasn't aware of it and had learnt it the hard way.
Thank you so much for your tips. As a single woman, I need to do what I need to do to get by. This bit (no pun intended) of information is extremely helpful.
You’re welcome Dionne! Thanks for watching...and for the pun 😄
Let’s be honest pun was intended
nice play on words ( pun intended ) lol
Great tips. I think I have done every one of these at some point. One I would definitely add is adding oil when drilling metal. It helps the cutting, keeps the drill sharper and helps cool the bit and material.
Thanks you so much.
That was years and years of lessons and experience in an 8 minute video.
Get a good countersink bit so you prevent the tapered head of a flat head screw from splitting the wood, especially near the end of a board.
And in a pinch, use a bigger bit to carefully drill out a small countersink.
Best DRILL video! It belongs on UA-cam University as a core class for crafter's like me.
Yup, me too, thanks!
Hi Gloria 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
I needed to drill two shelf bracket holes into an expensive curio cabinet. Super helpful suggestions!
Thank you for such clear and concise bunch of VERY useful tips! I’ve made a few blunders lately despite years of experience so it’s never too late to sharpen up the skills.
adding to the vid, putting a piece of wood underneath the piece you're drilling into will also help prevent tear out.
Other than that, well paced and informative video. Thank you.
I found that out by accident. Spade bits are notorious for tear out. So far..I have not had any problems. I try always put a small piece of board underneath. So far ..so 👍
So far so good.. The 2 boards should be clamped togother if possible..time permitting ..and other factors...going slow or. A marker tape for depth are choices.
Oh yeah..years ago I bought a 50s hand brace..geared, and good quality wood handle. They built ships and houses out of them. I am old school. Sometimes I like to do something totally using hand tools.
The bigger the bit you're using, the more you need to use a sacrificial backer board.
Without exception, even with brad point drills, always have a board supporting the location where the drill will exit the wood.
This is great! UA-cam is like a handy dad. Now I can be a handy dad for my kids.
Yep. Except I’m not handing out tools and getting yelled at.
Thanks for the MANY valuable tips for drilling, etc for DIYers. Some knew about before, but others that I will apply. Looking forward to your next video.
It's fun watching someone pass on info, for stuff that I have been doing over 30 yrs. It's always new to someone!
I always watch ‘Basic’ videos. Amazing how much I’ve learned
by not thinking I know it all.
You offer quick and precise instruction. Cannot thank you enough!
Thank you so much for making this video! I have had no training whatsoever, but have been building stuff for quite a few years, something I enjoy doing. However, I have had a lot of problems with drilling in the past. These tips were very helpful. A few of the things I had figured out to do on my own, but didn't know most of them. Can't wait to go drill using these new tips!
Excellent and short, right to the point. Thank you for saving my time.
2 years after you filmed this, amazing info for me, I just bought my 1st drill and I'm putting up shelves. A few of your videos with fantastic tips and I'm confident I can do it with ease! 💁♀️☮💕🇨🇦
Thank you for all your videos. I was trying to make simple plant stand and a bench. They are ridiculously expensive in store. I was inimidated by the amount of tool I needed for making stuff. When I came across your channel, I knew I can get away with 2 tools. Thank you for being honest.
Two thumbs up! I always thought drilling slowly on the wood prevents chips, but learned something new today!
Thanks for tips, Ethan. I wish I watched this before recently drilling into metal studs to install toggle bolts. It seemed to take forever.
On the bright side, I somehow figured out that I had to step up drill bit sizes for each hole. Seeing this approach confirmed in the video makes me feel a bit handy-dandy 👍🏽
Thank you so much! I spent forever online trying to figure out how to drill through metal and I learned so much more.
Great basic review. Glad to see I'm already using all those techniques. With regard to the painters tape, giving yourself a little extra wiggle room and not going to the depth of the tape is key when doing many holes; 1, 2, or a few probably won't be an issue, but the 144 I did for making a 6 hole adjustment for 6 shelves...the tape wears quickly. I also wind the tape counte to the spin so if the tape does touch the surface it doesn't unwind. I also use a long length of tape to give you more "bulk" at the stop point and fold the last half inch into a little flat so you're not only more likely to see when you're getting to close to the surface, i.e. drilling too deep, but it also makes it much easier to have the flap for unwinding it from the bit when you're done.
This was a perfect video for a beginner like me! Great tips!
Thank you for the tips really helps me with learning about tools.
Thank you so much! This is so helpful for someone who has 0 drilling experience like me
So many questions FINALLY answered! This was awesome! Thanks!!
Hi American girl 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Great tips as always - I used coloured tape matching the rawlplug colour and depth on my masonry bits so they are ready to go, and easy to identify at a glance which plug goes with which drill.
Remember, when you’re clearing out swarf (I love that word) with your finger, be careful that the bit isn’t hot, or you could burn your finger (ask me how I know this).
You ain't the only one. If the bit is tiny, dad flicks the end of it. Usually the little bit of flex and rebound is enough to bounce out the swarf. My fingernails are always uneven lengths; I just use whichever one is long to clear out the swarf.
I love that word too. :)
HOW DO YOU KNOW THIS?
@@philipwright6065 ever touch a drill bit after drilling for a bit? Then you’ll know. Lol
@@ethanheyne It can't hurt to let the drill have a break to cool down, too.
Swarf would be a good name for a small dog.
Ha ha. Same.
I liked this video. I've been a carpenter for 30 years and never heard of swarf. One tip that you left out that I like is when drilling with a spade bit or hole saw only drill until the point on the bit comes out then flip the wood over and drill the rest of the hole to prevent tear out. Keep making great videos!
Thanks man. Learned a lot and confirmed a few lessons that I’ve learned myself the hard way. For plasterboard fasteners I keep an old bit of plasterboard in my garage so you can practice and see what’s happening before drilling the walls in my home. 👍
You have no idea how valuable this video was for me. 👍
Some I knew about. But as always learned more. Also when drilling metal you usually want to use drilling oil if applicable.
@JosLewisWood Carpenter I had a metal shop teacher in 8th grade teach me about slow drill speed for metal, but otherwise I'd never have known this.
After so many videos and articles this one was everything I needed. Very concise, thank you 👍🏽
Thank you from an absolute newbie to DIY!
You've answered all my questions in one go! Many thanks for sharing.... I'm off to put up a roller blind.
Wish me some beginners luck please.
Hi Susannah 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
Great video, lots of good info. One thing I discovered:
I bought 10 packs of cobalt bits on line, of the most popular sizes that I often wear out or break; 1/8 and 1/4. Not too expensive, and cobalt bits are excellent!
You're so right about 1/8" bits. I always have extras.
You sir saved my drilling and DIY life. Thank you for your awesome videos!!
I liked the video. No one in my family ever used a drill themselves. Now i am thinking of getting one and trying to do things myself. Thanks a very informative video.
Great description of techniques, # 12 could be to apply a backer block (clamped or flat on the table) to avoid tear-out on the back surface of the work piece.
Thank for this video. I’m a beginner and now I feel confident to start my first project 👍🏾
As a DIYer I really have enjoyed all of your videos amongst the many that I watch. Thank you for being dedicated to your trade and teaching it to others. Awesome stuff.👍🏽
Thank you, gr8ride!!
I always thought higher speed was better for drilling metal, but now I know slower speed is better, thank you for this wonderful video.
Also should I use any type of oil for metal drilling
I learned the size up trick on my own when drilling into concrete. Helped tremendously
Yep, ESPECIALLY important in concrete
Do I need the hammer function turned on for the second (or third) size up on concrete wall? Because I live in an apartment, so I try to drill as least as possible and those hammer drills can get very LOUD, lol.
@@cynicalheis You have to use a hammer drill with a masonry bit when drilling concrete. Concrete is way too tough and hard for normal drills and just rotary drilling.
@@cynicalheis you may try a neumatic hammer drill, works better, no need force, not that loud.
I've commented before; but that Hitachi drill is the shiz! I've had one for years now. It's been my favorite by far.
Really cool tip see someone else with one! 👍🏼👍🏼
hitachi bought metabo, so actualy is a metabo drill. good stuff
thanks for the good tips. the aggressive reaming bit had me in stitches
Excellent in formation for self teaching. Your time.is appreciated
using a drop or more of oil helps when drilling steel and dishwashing liquid when drilling metal. allows for faster drilling speeds.
It's a good idea to use a coolant when drilling metal. This will extend the life of your bit before it gets dull. Even a light oil like wd40 is better than nothing.
Llllllllllllllllllllllllllllá0
Just stumbled upon this channel today and have already learned so much.
I thank you for your sharing knowledge. It’s better to give than to receive. God bless you and your family and business for doing this.
found a drill bit hole sizes template (13 hole sizes: 1/16"-1/4"), test the screw on a hole where it goes through and pick a drill bit 1 hole size smaller for hardwood, 2 hole sizes smaller for softwood
@@torTxoFognaTuluZ mastercraft hammer drill - included in the set of drill and screw driver bits (labeled as 'drill gauge'). it's 3x8 cm, made of plastic
Great Video! Recently found your channel so a new sub here. One tip that I like for finding the right size drill bit to use to pre-drill for a screw is to use the drill index. Find a drill bit that the screw will just fit into easily then go down two to steps smaller from that drill bit size. You can vary the number steps for softer or harder woods.
Just having a good old sort out in the shed and needed something to watch between sorting. Just the tonic. Thank you, great video
You answered my question about drilling for metal screws (bolt actually). Start with a bit that is just the shaft thickness then hog out the hole if necessary. Really loved this video. Thank you for posting the tips.
Good tips!!
When drilling into concrete, Mark the depth you want on your bit with a black sharpie.
the drilling dust will make any mark on the bit unvisible. most of hammer drills have a depth controlling device. or make one by yourself
@berndeikers8924 they do, but from my experience, someone always loses it, lol. Whatever way works, I suppose, because there's a few ways to get it done
Dang, if I keep watching his videos he's gonna make me into an actual carpenter.
My mother was a great self taught woodworker. She taught me most of these tips. Thanks for the reminder.
Great explanations, not everyone can organize info that is easily consumable!
Great video as always. Keep up the good work!
Thanks buddy!
With the tape on the bit method, another good trick is to leave a flap of excess tape folded onto itself. This serves to sweep away saw dust from the surface being drilled once you’ve reached to prescribed depth without you having to peer down at the work so closely.
Amen on slow and pressure for drilling or using self-tapping screws on metal!
Very well explained. I just bought my first drill and these tips are really spot on for a beginner like me. So thanks a lot.
Very helpful to dyi’ers, especially those of us who weren’t allowed to take shop decades ago (because I was a girl). I’ve figured out most of this on my own as I love rehabbing homes for myself and my friends. Your video would have been great back when I had to figure out what I was doing wrong; now looking for instruction on what all the fancy drill bits are supposed to be used for as I have a number of them that came in a huge set but they don’t tell you what they do or in which applications they should be used. Thanks for the clear instructions!
Hi Stephanie 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
If you're drilling with a fine bit and it snaps and you don't have a spare, grab a nail of the diameter, snip off the head and use the nail as a drill bit. It's not perfect but can get you out of a tight spot.
Another great tip Maxx. I’ve got a certain way of cutting then to get kind of a chisel point out at the end. Have definitely used that trick more than once
Been there done that..the fine brass looking ones that come in a blister pack (read cheap), break super easy. It just occurred to me.
If you are not making progress
with the bit..put it in vice or clamp. the nail to a table..then file cross hatches or just basically rough the tip area of nail up. Never tried it ..btw..I am in the process of putting brushes etc in my 30 year old Ryobi hammer drill. It has been put though the.ringer..
Extremely helpful for beginners.
Many thanks, Ethan. Plenty of useful advice which I shall keep in mind.
Also, get some bees wax or a bar of soap to apply to your threads before inserting the screw, especially in hardwoods. This will make the screws go in so much easier. P.S. If you are doing a lot of toenail screwing then get a Kreg jig (I know, this is not a simple screw technique but wanted to throw this in).
Also any any kind of candle wax will work. Which most house holds have.
@@angellas.1314 Cool. Was just going to ask whether candle wax would also work. :-)
Just bought my first drill, and thanks to you, I know how to use it
Hi Brenda 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
thank you for sharing your knowledge.
i’m newer to using tools- alot of great info that i didn’t know. thank you!
I am loving your channel. I just bought a house and I'm trying to save money by learning to do things myself. You have helped me a lot. Which of course saved me a lot of money. Thank you!
@tamasaii You’re welcome! Thanks so much for watching. I’m glad it’s helping 🙂
Some stores will markdowns wood up to 70%..I recently found.out that slightly defective
boards etc can qualify. Just ask
..it doesnt hurt anything. Stores
actually benefit from this..it saves
them from.having shoddy stock and taking the time to cull lumber.or.any other.product. I use old pallets to hold things..of course safety is always your.first
concern.
Thanks! I now have to salvage my project. Drilling fast takes confidence so I think it's wise to test on a piece of scrap wood. I also have a problem to drill straight for my dowels.
To help drill straight vertically. Fix together two pieces of wood to form a L shape about half the height of the bit your using. Then place the bit where you want to drill,and then place the L shape piece up against the bit where the corners meet. Then drill; it will not be 100%,but much better then trying to drill free handed. Also to drill a straight hole horizontally; you could do the same thing,but it can be cumbersome. I saw a trick on "Wood by Wright" where you place a cheap ring,key ring,or perhaps even a washer onto the drill bit itself so it can spin freely; then place the bit where you want to drill,and place the ring about middle way of the bit then drill your hole. An if you tilt the drill up to much the ring will slide towards your work,and if you tilt the drill down to low the ring will slide toward your drill. I realize the last tip sounds like a lot,but once you try it you be like oh okay piece of cake. LoL Hope this helps.
www.amazon.co.uk/Wolfcraft-4640000-Dowel-Master-dowel/dp/B0001P19PY
@@davogifman542 Can you show a photo of how this is set up. Also, looking for something like the wolfcraft fowl jig listed below in the US. Thanks so much.
@@liamofthornhill Can you tell me what a cheap comparable jig would be Amazon US? I'm putting together a bed frame with 2" x 2" poplar hardwood with a butt joint, and I think it will be hard to make straight holes. Thanks.
@@barbarakaimowitz9138 www.ebay.com/itm/Handheld-Woodworking-Doweling-Jig-Drill-Guide-Wood-Dowel-Drilling-Hole-Saw-Kit-/224246369046 I'm in the uk but eBay is a good try
Definitely learned a lot from this. Plain and simple. Thank you, kind sir! 😊
I agree with you on the "punch" thing! It can be really annoying when the bit wanders around on the surface on it own. Sometimes you don't have something to punch the surface with though. What I do is I place the bit where I want it, then I place my offhand on the back of the motor casing, above the drill grip. I then apply pressure, and give a short, quick pull on the trigger. Makes sure to do it fast, so the bit stays in place. Another method I found is taking the right size bit, or a bit smaller than it, and grab it in your hand, and twist it side to side, making a little indent in the surface your drilling. This effectively does the same thing as a punch, but it may not go as deep.
Thank you so much I was looking everywhere for "why won't my drill bit cut through hardware" when all along I just needed to clear out the swarf... 🤦♂️😂😂
I'm so glad you wrote your comment. I first watched this video a couple of days ago and have been wracking my brain trying to remember the word "swarf" and it was driving me nuts, but I remembered a comment of this nature and dug in my history for a video about drilling so I could find this word without having to rewatch lol XD It's not even in the Wikipedia page that has a glossary of woodworking terms, I looked! Thank you lol!
@@ItsAsparageese lmao you're very welcome! =D
All the new terms I discovered: swarfing, hogging out, toenailing... and also how come I keep breaking drill bits. Thank you for this! I learned a lot.
You're welcome, Bonnie! Thanks for watching :)
There are a few reasons why drill bits break when I'm using them.
1. I'm pushing to hard
2. Drill bit caught on a harder material while drilling into a hole. Example: Drilling into wood and you hit metal. The drill bit catches on the metal and breaks.
3. Cheap drill bits. Always buy good drill bits. For most DIYers and Contractors HSS drill bits will work just fine. HSS stand for "High Speed Steel." These are drill bit that have been heat treated to increase the hardness of the drill bit.
4. Drill bits typically go on sale: Christmas, Father's day, Memorial Day, 4th of July, Labor day. However, I find quality drill bits at their lowest price during the Christmas shopping season in the "stocking stuffers isle" or on Father's day. The big box stores put them out as their loss leader and you can typically get them for about 40-50% off.
5. Last but not least. Always wear safety glasses.
Bits break often for three main reasons:
-pushing too hard (small bits flex)
-change of direction 1/2 way through hole
-cheaply made bits (bad temper on bits)
Hi Bonnie 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….🌹🌹🌹🌹
Hi to mrJD - Liking the idea of coloured tape matching the rawlplug colour. That is one hell of a good tip. Ain't gonna forget that one. Thanks goes to The Honest Carpenter for creating this platform. Cheers and happy drilling !!!
Very informative and right to the point. Loved it!
Great tips Ethan....”swarf”....who knew lol
Thanks Ed! Always liked that word 😁
I have never held a drill in my life, and I'm not looking to drill anything anytime soon. But damn that was entertaining to watch.
There may come a day when you need to perform a simple task like hanging some bookshelves for someone special. Now you will know how to do it, and you will be a real hero. Believe me I know. I have done simple projects for friends, and they love when I break out my tools and get to work.
Thanks a lot for your lessons, tips and help...
A tip for masonry, that I learnt recently
Make sure that the masonry drill bit is all the way to the back of the hammer drill/ drill hammer setting.
Thanks for sharing these useful tips, some I knew some I find not
When drilling metals, every type of metal has a range of speeds for a given drill material. It absolutely does matter. I've made a nice living getting tools running at efficient speeds and feeds. It isn't always best to slow down, it is always best to let the tool do the work, and to have your head out of your ass when in the shop.
Applying cutting oil, ( me , pb blaster , got cans of it every where) on metal, usually helps.
I’ve been accused of “hogging out” a few holes in my day😏
Thanks for the video ! I am delighted, many many of your solutions I figured out myself ! Not to say that others have not done so too, but sometimes you just have to figure out how things are gonna work !!
I agree. As time goes by you develop confidence. We know what doesn't work and go from there.
I bought my first drill today and although have drilled a few holes with it I am glad I found this today. Thank you for quick helpful tips.
Hi Lesley 👋 I hope my comment didn't sound as a form of privacy invasion your comment tells of a wonderful woman with a beautiful heart which led me to comment I don't normally write in the comment section but I think you deserve this complement. If you don’t mind can we be friends? Thanks God bless you….
I've been a machinist and maintenance mechanic for fifty years of my 75 years in life. I can't tell you how many finger and hand infections I've had from clearing chips from drilled material using my hands or fingers. I learned what chip brushes and low air can do to remove chips without consequences. Just a thought. !
That’s a good point Frank. Thanks for writing in with the advice!
Tip 12: Wait for the drill bit to cool before manually clearing swarf. I really messed up my urethra once by not following this tip.
Jeeze dude, the stuff of nightmares !!
What??
Funny stuff.
High quality videos. Seems simple to me but I did learn something and these days lots of people need this
It the little things that help the most. Thanks for a detailed and very informative video.
Hersa a tip: when drilling in wood, use wood drill bits
SWARF : Stuff Without A Real Function 😜
I loved your video. Such an informative video. I am not a professional woodworker or even a serious DIYer - just a handyman who learned stuff from my father who was an engineer (I'm not!). I have a basic Bosch power drill and a few drill bits but use it a lot around the house, fixing stuff. I found some of your tips so helpful and practical.
To avoid tear out I have used tape as well but I prefer to clamp a piece of waste stock to the side where my drill bit will make its exit. I can always find a big enough piece of scrap wood to cover all the area where I am drilling holes to prevent tear out.
When I use hole saws or spade bits. Having scrap on one side is a big help but mostly I drill a smaller hole through my project first. Then use the spade bit or hole saw and just penetrate the wood on the one side part way in. Then drill through from the other side all the way using the small hole that is showing as my start point. That way you avoid making a messy tear out because the surface of the wood on both sides has been cut with no cutting tool that has broken through. I always keep in mind that some woods are more prone to splintering than others.