How to Replace Front Wheel Hub 11-14 Chrysler 200
Вставка
- Опубліковано 25 сер 2024
- Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com 1aau.to/ia/1ASH...
This video shows you how to install a new, quality, TRQ wheel hub on your 11-14 Chrysler 200. Head over to TRQAutoparts.com for more info!
• Check here for more videos on the 2011-14 Chrysler 200: • Chrysler 200 2011-2014...
This process should be similar on the following vehicles:
2011 Chrysler 200
2012 Chrysler 200
2013 Chrysler 200
2014 Chrysler 200
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 14mm Socket 1aau.to/oa/1AXA...
• 15mm Socket 1aau.to/oa/1AXA...
• 18mm Socket 1aau.to/oa/1AXA...
• 19mm Socket 1aau.to/oa/1AXA...
• Brake Caliper Compressor Tool. Single Piston. Lever Style. 1aau.to/oa/1AXA...
• Brake Caliper Hanger 1aau.to/oa/1AXA...
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• 1-1/4 Inch Socket
• 1/2 Inch Breaker Bar 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Anti-Seize Grease
• Copper Anti-Seize
• Rust Penetrant
• Hammer 1aau.to/oa/1AXA...
• Wire Brush 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Chrysler 200 2011-2014 1st Gen: • Chrysler 200 2011-2014...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Good video. Clear explaining. This will help me greatly with my 2012 200s. 196k and doing well
Thanks for calling out the torque specs, super helpful.
Very clear video to see what’s going on, thanks for sharing, subbed 👍👍
Thanks for the video, saved me a good amount of time!
I tried this but I just need to get the stud onto the hub n that’s it but the bolts are giving me hell I’m guessing that u have to remove the hub nut then try taking them off?
For the caliper pins, I was taught the pin with the rubber bushing is always the trailing pin. Putting it at the top would make it the leading pin as the wheel moves forward. Are you sure it should go at the top?
Great video thanks
+Heather Pillar Thanks for watching our video! 1aau.to/m/Shop-TRQ
What do you recommend as a brake lubricant to prevent the breaks from squealing?
What do you call the little washer that sits between the hub and axle i cannot find a replacement and mine were pretty rusty new assembly didn't come with any
I cheated, supported the caliper and bracket instead of taking it off the bracket lol much less time consuming
I never understood why other techs always take the caliper and then the bracket off when you can just take the bracket off and save yourself a step and second why would you compress the caliper after you loosened it
Maybe they put new brake pads on but forget to tell us.
Can I use an impact gun?
What happens if you don’t torque your bolts ?
Two ugga duggas will be ok on this. Three on the axle nut.
I never torque mine lol I just do it. I even have a tq wrenchlol
Just tighten as tight as you can with a good wrench you'll be fine I never torgue done either