initial thoughts, bent spindle. Still watching,,,,,,wooooo hoooooo I’m learning,,,,,, woooooooo hoooooo Mrs T and you got her cleaning! bad T-Bone! See if I can cut my hand off 🤣🤣🤣 so funny. You’re the man sir,,, tooooo easy,,,, I give your other channel a shout out coming soon brother
I liked because I got me a John Deere . In 15 hours the motor was a goner shaking all over. They came and took it. When I called them they said maybe I’d get it back in a week or maybe 6 months. That sucked so I called John Deere corporate. Didn’t take long till I was called and told it was done. Took 3 more days before it showed up. Ran and started right where before it was always hard to start. Hooray!
T, this has gotta be the best one of your videos I’ve seen since I subbed, if for no other reason than your black humor. Throw all those things on the floor - they’ll show up eventually. Kind of like, here’s how NOT to do it, dummies! 😂😂😂
Hey are you doing good job keep it up bring more videos and teach me good things how to fix my tractor and think it wasn't for you I want to know how to fix it
Up to now most of what I’ve seen on UA-cam about John Deere has been negative, but I have to say, there are some really good design features on this machine. Those spring clips really solve the problem of installation and removal single handed. Somebody was really using their noggin.
😆 🤣 yep. In the next video it's even better because I actually read the destructions 😆 and found it has a noise cancelation button 🤣 it's crystal clear with no background noise now.
Spring-loaded spindle covers! If shaming Tony on international UA-cam doesn’t get him to change his ways, nothing will! 😂👍 Absolutely no excuse for not cleaning those out and avoiding rusted out spindle mounting surfaces! All they need is some sort of spring-loaded clip to hold them open and cleaning just never gets easier!
This video got you a new subscriber. I have a Z375R and changed the blades and had vibration. Couldn't figure it out. Went back and checked and found one blade was not seated correctly on the spindle. Thanx a ton, you saved me most likely a huge repair bill for something simple.
Hey you make more videos man I would appreciate it nobody as good as you thank you for the tips and the tricks thank you for teaching me how to get the motor up and running
Question pls..ive put on new blade tighten the bolt all the way but the blade just spins freely, sometimes it tightens but mow 2min then loosens again.. Any idea
Did you find the problem? Make sure they are the correct blades, match the center hole to your old ones. Make sure your splines on the spindle are worn out if your has splines. Make sure the cupped washer is cup up. Good luck!
T-Bone After Hours Channel Link
www.youtube.com/@T-BoneAfterhours
You're right about Taryl's video his are like you're videos very informative and easy to understand.
Glad you like them!
Man you do an excellent job of making an expensive repair doable. THANKS😍
initial thoughts, bent spindle. Still watching,,,,,,wooooo hoooooo I’m learning,,,,,, woooooooo hoooooo Mrs T and you got her cleaning! bad T-Bone! See if I can cut my hand off 🤣🤣🤣 so funny. You’re the man sir,,, tooooo easy,,,, I give your other channel a shout out coming soon brother
Glad you enjoyed it. Thanks so much my friend.
Audio - very good.
Great, Thank you
You're welcome.
Another great video my friend!
Thank you my friend
I liked because I got me a John Deere . In 15 hours the motor was a goner shaking all over. They came and took it. When I called them they said maybe I’d get it back in a week or maybe 6 months. That sucked so I called John Deere corporate. Didn’t take long till I was called and told it was done. Took 3 more days before it showed up. Ran and started right where before it was always hard to start. Hooray!
👍👍👍.Thanks
Nice job T-Bone, Mrs T-Bone sure was sweet to clean the spindle beds off for you. 👍👋
The new mic sounds very good, you got the right one.
Yes Mrs T is amazing. Thanks brother
Anytime 🙂👍🏼
Thanks for a Great video. This may help to solve my excessive vibration on my Z335
Great video 👍
Thank you
Good job T Bone
Thank you
T, this has gotta be the best one of your videos I’ve seen since I subbed, if for no other reason than your black humor. Throw all those things on the floor - they’ll show up eventually. Kind of like, here’s how NOT to do it, dummies! 😂😂😂
Thank you for your kind words my friend.
Audio is awesome.
Thank you Bill. This coming Friday will be even better, I discovered something new!..
Hey are you doing good job keep it up bring more videos and teach me good things how to fix my tractor and think it wasn't for you I want to know how to fix it
Awesome video sound perfect Thank you
Thank you
This video is the first I’ve seen on bent spindle shafts. Now you got me searching for how to straighten them. Thanks a lot! 😉🔧😂👍
You can replace just the shaft, but it may have damaged bearing also which is easy to replace also. Thanks for watching and commenting my friend.
Up to now most of what I’ve seen on UA-cam about John Deere has been negative, but I have to say, there are some really good design features on this machine. Those spring clips really solve the problem of installation and removal single handed. Somebody was really using their noggin.
MIc sounds awesome....when you turn it on. When you forget to turn it on, not so much!!! lololol
😆 🤣 yep. In the next video it's even better because I actually read the destructions 😆 and found it has a noise cancelation button 🤣 it's crystal clear with no background noise now.
the sound was great , thanks for the video'
Awesome, thank you
Great video as always . Love all your videos
Thank you
Spring-loaded spindle covers! If shaming Tony on international UA-cam doesn’t get him to change his ways, nothing will! 😂👍
Absolutely no excuse for not cleaning those out and avoiding rusted out spindle mounting surfaces! All they need is some sort of spring-loaded clip to hold them open and cleaning just never gets easier!
😆 🤣 He just picked it up this morning and said he hasn't seen the video yet. Lmao 🤣
@@RaleysSmallEngines
😂
Video sounded great with the new mic!!
Thank you
awesome video my friend keep them coming my friend love your work
Thanks, will do!
That’s a great impact - always starts on the second pull! 🔧👍
😆 🤣
This video got you a new subscriber. I have a Z375R and changed the blades and had vibration. Couldn't figure it out. Went back and checked and found one blade was not seated correctly on the spindle. Thanx a ton, you saved me most likely a huge repair bill for something simple.
U. R fantastic. What do u do after hours. I learn. A lot.
Thank you. Check it out T-bone After Hours UA-cam Channel, link is in the description
Heyhey ol boy, great info. New mic sounds great
Thanks Rooster
Excellent video T-Bone well explained, and the sound quality was really good 👌, and well done to Mrs T-Bone for the clean-up job on the deck 👏 👍 😀
Glad you enjoyed it! Thank you my friend.
Enjoyed the video sound quality is really clear ,question does rotary sell to the public or only small repair shops. Thanks
@@pitbull4029 thank you. Rotary only sells to repair shops
Hey you make more videos man I would appreciate it nobody as good as you thank you for the tips and the tricks thank you for teaching me how to get the motor up and running
Glad we could help. Thanks for watching!
2:50 no chill made me lol!
Thanks for taking the time to show how to fix a mower so helpful and step by step
Another great educational video, thanks for the patience and detail in explaining what's going on! Keep them coming.
Thank you
Another top notch video. Thanks.
Thank you Rob.
The audio was great T-Bone! Great job.👍🇺🇸
Awesome, thank you!
Thank youfor the video. Blessings to you.
Good video, thanks
Great video! Good project! i Love your new mic. i love watching your videos.
Thanks Warren.
Awesome video T Bone. I do a ton of those spindles yearly.
Thanks Terry. Yep someone is always hitting something 😆 $$$
Great video... as they say "easy peasy"
Thank you, yes sir... too easy
Just like my great nephew
,he is lazy
Yes,he is
Very helpful thank you
Nice video t-bone I don’t understand why they put a grease fitting on sealed bearings
Thank you. Yes, Exactly!!
It sounds good
Thinking star shape for blades to lock in is all mashed up and blad is on top on one side
Do they make the covers over the spindles for troy bolt
Yes, but they are metal. You can look them up on Parts Tree
Some may like a vibration feature....but I say no, leave that for the lounge chair 💺 or recliner.... AIN'T IT JUST AIN'T IT 😜 lols
LOL Too funny
He definitely needs to go clean up the mower deck
Tee BONE..10. 4
I thought that the vibration was there to make mowing more fun. My mistake.😮
😂😂Too Funny
It’s a mess with mix of std and mex bolts on every single thing now 😢😢
They need to get it one way or the other 😊
Question pls..ive put on new blade tighten the bolt all the way but the blade just spins freely, sometimes it tightens but mow 2min then loosens again..
Any idea
Did you find the problem? Make sure they are the correct blades, match the center hole to your old ones. Make sure your splines on the spindle are worn out if your has splines. Make sure the cupped washer is cup up. Good luck!
💯💪🏾
Thank you my friend.
T-Bone if Big Son's ever offers to draw or weld something for you just RUN!! 🤣🤣
@@Big_Johns JOHN KLEM!!!!!!!!!!!!!!!!!!!
Well hey Mr Renaldo, how are you sir?? 🤣
@@Big_Johns All good my brother I'm over watching Big Dogs video 👍🏾
That don't know diddly
He is lazy, what if he has a right hand messed up