Compiling Sonic Pad for SKR MINI E3 V3 (unsupported motherboards)
Вставка
- Опубліковано 30 вер 2024
- Creality github:
github.com/Cre...
Klipper GitHub:
github.com/Kli...
If I helped you out and you’re able to tip, I’d so appreciate any help! Thank you a bunch! 🙏 :)
bmc.link/littl...
(Tips are through buymeacoffee.com)
This didn't solve my specific problem (getting the Creality serial cable to work with the SKR) but it was such a good tutorial for any entry level users following in our wake, that I just had to give it a thumbs up.
I have followed these instructions to the letter and I am still having a problem. I get to the very end and its "LOADING" then it reads as follows. (( Internal error during connect: can't convert negative number to unsigned ))
Hi could you make a guide with nebula pad kit and SKR MINI E3 V3 .3d printer Ender 3
hello i´ve great problem . at trhe part ./install-ubuntu-18.04.sh . i received the messge klipper is not in the sudoers files . plz help
Greetings, Thank you for a great tutorial which I used to to build the bin file for my SKR Mini E3 V3. The board flashed perfect and after some mix and match effort with building a printer.cfg file, BTT pin out configurations, I was able to get the Sonic Pad and the SKR board to work.
I do have an issue with the Self-Test feature of the Sonic Pad. It will allow for the hot end and parts cooling fan test to run and complete but it does not allow the Z-Offset, Bed Leveling or Bed mesh feature to show up. ???
A side note the SKR Mini E3 V3 is using the STM32G0B1RET6 chip which is not in the Sonic Pad listing. Any Thoughts would be helpful. Again a great job for showing how to build the bin file.
Doc'
my terminal doesn't open
Hey everything went great but i have 2 problems. Every time i turn off my printer and then turn it back on i need ti setup the printer again like i just bought the sonic pad. And also the cr touch when homing turns from purple to blue and doesn’t eject the probe and i get an error. Can you please help me ?
Thanks for the video, but I want to ask something. I have done everything, I have inserted the sod card with the bin file to the skr 3 v3 but when I try to add the printer from Sonic pad it can’t find the printer.cfg file. Any help?
Hi looking for help i have got a ender3 with a SKR Mini E3V3
,sprit pro exturder and a cr touch i think i can follow this but is there any thing else i need to configer to make my printer run thanks in addvance for any help you can give
I have a cr6se with a bigtreetech cr6 mainboard and Pheatus Dragon standard flow hotend with orbiter v1.5 extruder. I would love to get this working with no issues. Does anyone know how to get it in that machine? Thanks in advance.
Hi LittleLoud...amazing your video.... i have followed your steps one by one....but now the SMT32G01B1 dont exsit!!! it doesnt appear on menu config....i have bougth skr mini v3 but now i can not configurate it.....
I have tried to upload both file to this reply but so far I have not figured out how to make it work. Any thoughts?
Doc'
Greetings, Well Done and again thank you for your efforts. One item though, you did not cover the Self-Test features for Z-Offset, Bed Leveling or the Bed Mesh. It would be nice to see how you did them with the sonic pad or how to successful use the Klipper UI to run the commands for those features. Once again thanks well done.
Doc'
Thank you very much, your video as complete. She's so very cool 😁🤩😍
This helped me so much! Flawless tutorial, thanks :D
Did your printer flash the firmware without any problems? My Ender 3 Pro is stuck on the flash screen and there is nothing about klipper in the serial ID. Do you have any other experiences?
@tristanhein3744 no I don't have a lot of experience really as this is also my first time working with klipper. By "stuck on flashing screen", do you mean the LCD screen is blank? This is intended because when you flash firmware for the Sonic Pad the printer doesn't use that screen anymore but only the Sonic Pad.
yes i know, its blank. But how do i know that the Klipper firmware ist succesfully flash on my printer. Im stuck to the point where i emailed myself the .bin file and flash the printer.
@@JulianGaming007
I tried it but when i go to make it i get errors , the out folder is there but no .bin file
please can you send me the bin file for my printer?
Hello, may I ask you? I don´t see processor STM32Gxxxx I have visible only STM32F a H? Where will be problem?
You need to compile the firmware for that processor yourself because Creality Sonic Pad uses outdated Klipper software and doesnt recognize a lot of the newer processors. That's literally what this tutorial is for.
Hello, is there a possibility to compile Sonic Pad for Prusa MK3s+ on the Atmega2560 processor? I've been struggling with this for several days, but unfortunately, after uploading the firmware, the Prusa hangs even though the slicer shows that the upgrade was successful. Would you be willing to help me or send the cfg file? Thank you and best regards, Tomasz.
Did you find a solution? I am at the same point with my MKS gen V1.4 mainboard using a Atmega2560 processor.
You just got a new sub for this thanks so much.
Duuuuuuuude. Thank you!!!!!
i got to the point where i loaded the firmware into my ender3pro, screen is blank now, Got the pad up but which file do i need to load? the skr or the ender 3 pro cr touch cfg
Nicely done! After flashing the printer, on the Sonic pad you would want to have a usb drive loaded with a printer.cfg tuned for your 3D printer. I have a video on my channel showing how to set up a printer.cfg. It would be having that file loaded on a usb drive and plugged into your 3D printer and selecting custom firmware on the Sonic pad and it should be recognized on the Sonic pad as being on the usb drive. Let me know if you have any other questions, hope that helps!
@@LittleLoudPrints i believe github has some printerconfig that are generic for this..... just no real good explainnation how to get to to the firmware etc load
Thank you! My v2 died and did not expect this much of a headache getting the v3 to work.
I’m glad I could help!!
I have worked out the Self-Test issues for my E3 S1 SKR Mini E3V3 printer and I have a firmware.bin and a printer.cfg file for it if anyone has a need. Once again thank you for this outstanding tutorial.
Doc'
Can you please send the above mentioned files for me?
@@peterpeter1763 Greetings, yes I can send the files if you give me a location to send them to or a how to do it in You Tube. Thanks for the read. Doc'
Would you be so kind to send me those files too? I cant figure out the .cfg file D:
can you please send printer.cfg to mee too
Greetings, yes I can send the files if you give me a location to send them to or a how to do it in You Tube. Thanks for the read. Doc'
Do you have a printer.cfg file for this one?
I wish I did, unfortunately I don’t have the skr mini e3 v3. On my list of boards to get though
So what happens when there is no download zip??? Or did that not cross your mind while doing this video??
Is this in regards to the link to Klipper’s GitHub that I provided in this description?
I too did not find the little GREEN Code button to download with until I resized the Firefox window by moving it and then resizing it in the Ubunut window. After figuring that out it went well. I hope that was some help.
Doc'
How did you resize the window
@@troybelanger5049 with the browser open I clicked on the right side of the title bar and pulled it down and to the left a little so I could see the top left corner of the browser. I then clicked the corner to get the diagonal arrows and re-sized the window to make it smaller. I then moved it to the left almost all the way and exposed the right hand side of the browser. I then clicked on the right hand side of the window and extended back to the right until it showed the green button. It took some practice but I was successful getting to the green code button. After clicking it I needed to move the window again to show the zip file and once it was there just click it and the download started. Boy that's a bunch to do to get a file.
What would be much better is if the Application would allow a full screen feature...maybe it does I just never fount out how.
Any thoughts LittleLoudPrints ???
Doc'
@@doctrainsmodifications5201 thank you