Sonic Pad | Setting up custom firmware | skr mini e3 v2
Вставка
- Опубліковано 18 лис 2022
- Printer used:
ender 3 v2 with a skr mini e3 v2 motherboard, linear rails, sprite extruder
Printer.cfg:
pastebin.com/Y2dzr3Ge
If I helped you out and you’re able to tip, I’d so appreciate any help! Thank you a bunch! 🙏 :)
bmc.link/littleloudprints
(Tips are through buymeacoffee.com) - Наука та технологія
Hey everyone. Just posting an update on the state of the channel.
I was recently affected by the tech layoffs happening(I have recently gotten a new job though) but before that I was hustling it to get a job, that combined with having a 1 year old has just made it really tough to upload. However I uploaded this video because I want to make fun and helpful videos and the goal is absolutely to do that full time.
Thank you so much for the support and I hope this video has helped you all in someway. Currently I plan to get a routine down that allows me to upload every week. I am currently trying to upload a video about the printer.cfg and how to set that up. I also want to respond to all of you in the comments and give you all a good response and solution for issues your facing. I’d also like to make this video again and give you an updated process. I hope to do this asap. I’ll continue updating the description with as many printer.cfg examples as possible for as many boards as possible. Thank you again!
Appreciate the video. I'm trying to configure my sonic pad to work with 2 different printers, one which is a stock configuration and was plug and play, the other is modified to where I need to build a custom printer config file. I've found your video very helpful
Greetings, Thank you for a great tutorial which I used to to build the bin file for my SKR Mini E3 V3. The board flashed perfect and after some mix and match effort with building a printer.cfg file, BTT pin out configurations, I was able to get the Sonic Pad and the SKR board to work.
I do have an issue with the Self-Test feature of the Sonic Pad. It will allow for the hot end and parts cooling fan test to run and complete but it does not allow the Z-Offset, Bed Leveling or Bed mesh feature to show up. ???
A side note the SKR Mini E3 V3 is using the STM32G0B1RET6 chip which is not in the Sonic Pad listing.
A review of your " Compiling Sonic Pad for SKR Mini E3 V3 " does not cover the pad's Self-Test functions.
Any Thoughts would be helpful. Again a great job for showing how to build the bin file.
Doc'🤔
I upgraded my SKR Mini E3 V2 to the SKR Mini E3 V3… can you make a video on how to compile info for that board?
Yes please
Please all my printers have it and need it
Hey all! Sorry for the late reply! Were you all able to get the skr mini e3 v3 going?
@@LittleLoudPrints no not yet I can’t seem to get it going could you make a video about it?
@@ChristianS23474 Yup, it will be my next video 👍
What do I need to change in the firmware generator page for a 4.2.7 board. I've posted and looked all over, but I can't find any information like the clock reference, the usb vendor ID, the usb device ID, or the GPIO pins
Sonic Pad is great if you have a stock Creality printer but i'm using an SKR 3EZ to run a 3V2 with DDX V3 / Mosquito and .9 degree stepper motors. If I would have known I'd have to setup a virtual machine I'd have just used an old laptop I have laying around
Thank you for your Video. I have a Anycubic i3 Mega, but i don't can use it with the SonicPad. How to flash the Klipper Firmware on the Printer? Is there a HEX File to download to flash it over the Slicer on the Printer. My I3 is Standard but with 2208 Driver. Can you help me? Thx a lot. Chris
For all of yuo that font understad , i sugest to read the Klipper Manual , its very good and after reading yuo gone see that its not so complicated , good luck😊
I have just tried this on my ender 3 with btt skr mini e3 v2, when i install the firmware.bin the sonicpad creates, it installs, as changes to firmware.cur but the sonicpar can no longer connect to the printer on the usb. Tried several !PA14 is set but nothing, i put marlin back on Amd works fin and usb connects as expected, any ideas please as i am now stuck!
So, I followed the steps from your tutorial. I have a 4.2.7 board (new and verified) in an Ender 3 Max. I used the Github 4.2.7 board sample and edited only the items (dimensions) as it pertains to the printer for the print.cfg file and it still won't work. I just throws an error about "cannot infer homing_positive_dir in stepper y". I also get some sort of connection error if I navigate to a setup screen. I tried updating the code with homing_positive_dir = true or false and neither changes the outcome.
Any ideas?
I got an idea , i have similar errorrs in my raspberry pi -klipper install , try to change the y offsets of yuor probe in yuor printer.cfg , when the compile is ok , try to make home
My Pad find no my printer.Cfg what Wrong i make ?
My sonic pad won’t read the printer.cfg file
this is for the old board. I have the 3 v3.0 so it doesnt have the firmware for mine
I'm stuck for the skr mini e3 v3 :C There's no option for the processor model for the stm32g0b1 even with the most up-to-date Sonic Pad firmware itself... Can anyone help??
I ended up returning my pad now that BTT is releasing their Pad 7. Hoping it'll be a much smoother experience.
Can confirm, the Pad 7 is much nicer for BTT boards. SKR mini e3v3 works like a dream with it.
Hello, I am going to install a sonic pad on my ender 3v2 with the Sprit extruder. Is it possible to take your printer.cfg file en put that on my sonic pad just simply using copy/paste? zo al the settings like offset of the touch and other bed settings or used ??I hope you answer and understand my question, Don't have the same motherboard as you have I believe
I think the things I need from you printer.cfg file are the settings needs to be changed like offset cr-touch , max -bed etc, settings I changed without the sonic-pad
I’m working on a video that is almost done, I’m hoping to release it this week. That is a great question you’re asking! And I answer your question in the video actually! The answer is yes and no, it’s hard to answer completely through a comment.
But the answer is yes if you have the same motherboard. This will mean the pins will match up and functionally, things should turn on. But exercise caution.
Not everything will work properly due to my printer not being a stock ender 3 v2 printer. I have modified my printer a lot and chances are you’ll have to change a bit. If the pins matched up and we had the same board you would have to still define the bed mesh minimum and bed mesh maximum - as well as the z offset. It could damage your printer, so please exercise caution. I will explain this is great detail in the video. But just know it’s possible that your printer could try to home to the right or maybe the crtouch will try to go through the bed. So if you try my printer cfg settings, you need to be ready to turn your printer off in case things look funny. My printer cfg settings are definitely made to be a reference point and made to save you time, but it still needs tweaking. My video will show you how set it up and tune it for your unique printer. And the best part is, it’s easy!!
@@LittleLoudPrints Hello I shall wait a while for you videos before installing the SP!! thanks for you response
I CANT GET MY SKR MINI CONNECTED BY USB, it seems to be dead with the usb /serial port:( ANY IDEA? Thanks for the video
I got same issue pal, usb is fine when on marking sonic pad sees it, as soon as I install klipper usb is dead and sonic pad can't talk to it, did you get yours going at all?
Is it possible to get the SonicPad to communicate with a printer with a CRtouch installed that didn't come with it by default (in my case a CR10V2)?
Great question, you most definitely can! In the printer.cfg you just want to make sure that the bltouch is enabled and that in [stepper_z] you have endstop_pin: probe:z_virtual_endstop
[bltouch]
sensor_pin: ^PD3
control_pin: PB5
x_offset: -30.7
y_offset: -40.2
probe_with_touch_mode: true
stow_on_each_sample: true
pin_move_time: 0.4
pin_up_touch_mode_reports_triggered: False
speed: 20
lift_speed: 5
samples: 4
sample_retract_dist: 8
samples_tolerance_retries: 4
[stepper_z]
step_pin: PB3
dir_pin: PB2
enable_pin: !PA5
step_distance: .0025
endstop_pin: probe:z_virtual_endstop
position_min: -2
position_max: 250
You just have to tune the settings, like the offsets, but these are examples on what it would look like in your printer.cfg
(I have the ender 3 v2)
@@LittleLoudPrints Thank you so much!
@@LittleLoudPrints Does all of that code need to be included? Or just the first line "[stepper_z] you have endstop_pin: probe:z_virtual_endstop". In my config file it just said to uncomment "position_min: -4
endstop_pin: probe:z_virtual_endstop" if I have a Bltouch/crtouch as iirc the way the code works the printers makes no delineation between a bltouch or crtouch and the code would work the same.
The bltouch section and stepper z section do have to be included in the printer cfg, but the values might differ slightly depending. The pins should be the same. I have a Crtouch as well. definitely make sure position_min and are not commented as well as that position_endstop in [stepper_z] IS commented, #position_endstop. Because the Crtouch will not need that. The printer cfg doesn’t need the Crtouch specified, bltouch in the cfg will still work with it
Hello, please help, is it possible to create instructions for installing a clipper on a sonic pad of various models, such as kingroon or artillery or mks mini board for Ender priners.
Uploaded a video on this today 👍
@@LittleLoudPrints 🤗
I do everything as you do , however , at the last stage there is no connection with the printer
Hello, were you able to solve it? I have the same problem
@@matiaspasminoandrade5550 i buy a new better cable and now all fine
what its differ original ?
Doesn't work with SKR Pico.
Puedes hacer un vídeo de Sonic pad con kingroon kp5ll
i tray do it vid my cr 6 se vith skr-mini-e3-v3 its sei feil ven i add the printer.cfg pad sey only feil tray to faind how to get it to worck
sorry for total bad english :D
Can i Start This With trigorilla chiron Board ?
Sorry for the late reply, yes you can. You’ll just want to search trigorilla pinout and edit the printer.cfg file for it to work with your board. You’ll also want to search for how to compile the klipper firmware for the trigorilla Chiron board. Is this your board shown here? imgur.io/YSgW2gn My next video will be on the printer.cfg. I hopefully will have it uploaded in a day or 2.
@@LittleLoudPrints hi thanks :) my Board Its the 0.0.2 trigorilla Board
I also don't understand ANYTHING in that Motherboard Firmware Compile section from 7:06 to 8:55. What does any of that mean? How am I supposed to know any of that information?