Hi, 20+ years as an appliance tech and 10 as hvac tech. Question: Why didn't you fill the system with nitrogen when checking for leaks? Had you found a leak, you would've had to recover all your refrigerant to fix the leak. I've always done it that way... I realize your way is faster IF there are no leaks. But if there is a pinhole leak in the solder, the nitrogen can just be quickly vented into the atmosphere, then you fix your leak, and then put fresh refrigerant in.
Our compressor was still working so brazed on a valve and replaced R134a (it's only 5 oz which is less than half a can you can get for automotive AC) and it's been working well for the last month.
When you work on dual evap LG's which Service Manuals do you use> The one I downloaded from the internet for my LFX31945ST does not have the correct info for checking or replacing the Ref compartment evap fan , it only refers to a single evap system and the fan in the freezer for the ref. compartment. Is there any supplement pages for this manual I could find? Keep up the great videos and info you provide to us.
Thank you for sharing this video...I have the exact refrigerator and the compressor has failed. It is under warranty, but it is good to know what will, and should, be done. Thanks again!
How long did you have your refrigerator before it failed? I have this exact same fridge as well. Have had it for 7 years now. Just died yesterday. Such a great fridge too.
@@ErichCervantezthese are lg linear compressors....they are lg science projects that have really bad service life. If your replace it tap condenser fan com lines and use relay between them and a standard compressor.
Hi how are you? i have a question if i have the same old compressor 220v 60hz R134a inverter GL and i wanna buy a new one but not inverter. Which compressor you do think is good ? Thank you!
In regards to the software update, is it with the LG software rewriter kit? Given the fridge is a Kenmore fridge is it correct to get the LG software update? Our compressor just went out it’s an LG compressor in a kenmore fridge and the sites all say our compressor has been replaced by a newer model but it also requires updating the software with the LG software rewriter…doesn’t make sense to me since the fridge is a kenmore fridge
If you’re using a drier with an access point, the side with the access point always goes to the Yoder loop. But you always want the arrow on the drier going the same direction as the Yoder loop. If reversed it’s probably gonna clog
I have another dryer on the intake line....the copper line on the bottom there is a small copper "can" that looks like a short fat version of the dryer you replaced. It sort of resembles a fuel filter. I didn't see you replace that.
I have the same POS model fridge and will need my compressor replaced. The compressor is under warranty, but the labor is not. How much do charge to do the replacement?
I have that same POS fridge! The compressors are made by LG, and they are known pieces of garbage, yet they continue to sell them for top dollar with a useless warranty of just one year. There have been class action lawsuits and their solution is to just keep selling them but limit the warranty so they aren’t responsible for the service bill (about $1,000). Never buy LG, Kenmore, or Samsung appliances.
Kenmore used to be an excellent brand refrigerator until the company went out of business about 10 years ago. LG knew their fridges was junk so they bought Kenmore's name and started relabeling their junky fridges Kenmore, smart on their part but bad for the consumer (very unethical). Samsung fridges do has a lot of problems.
My upright freezer compressor is running supee hot and not in a freezing mode. I have replaced the start device.. Nothing. I have try the 3n1.. Nothing. What could be the problem?
I need to change Kenmore invertor Compressor LG FLB075LBNA so if I'm changing compressor with the same series than I still have to change/install the software?
Thanks , how much would such a repair cost and any guide to diagnose as I have the same model , compressor seems to be working but no cooling , can’t seem to diagnose the issue before replacing or going for the big repair , appreciate any help , thanks
I have the exact same model and problem. The compressor comes on, the fan to the right of the compressor turns on as well. The fans inside the unit are blowing, but not cold enough. I'm sure you heard about the LG compressor recall? The Kenmore uses this LG compressor. It has 5 year warranty for the part, but not the labor to put it in. This guy says it's easy if you have the tools. Yeah, most average people, me included, do not have the tools used in this video.
How do I eliminate the inverter compressor, rather just use my nice French door fridge with a 120v r134a compressor ....I do commercial hvac...so I'm up to the task...any guidance of how to.eliminate the board or use the hoard to call my 120v compressor to come on...thanks
So much for elite huh...im watching this video because our 2015 Kenmore Elite compressor failed today. If I may ask, how much was the repair for yours? Im trying to get an appointment scheduled. Thanks!
@@rbljackson A 2015 Kenmore, Great Refrigerator and worth replacing the compressor! The compressor unit is expensive but covered by a 10- year warranty. Installation was about a 1,000.00, but the service guy suggested I purchase a Service Contract and the repair would be about 400.00. I entered the Sears Contract for 50 per month which covers all appliances. After 30 days the contract is cancellable, however, my refrigerator ice maker is broke and that was covered by the contract. I recommend getting that compressor replaced as the newer units I looked at just are not as good as that Sears Elite. It did take a couple of weeks to get the service done, in the meantime, I purchased an ice chest to keep food cold. Yes, an inconvenience, but it all worked out!
@@paulkoscheka4434 I heard that one person canceled the Home Warranty after a couple months and they went after her for the full amount of the discounted repair.
I just got off the phone with Sears. I will have to wait two weeks for a repairman. The monthly cost of the home warranty is $65 a month. I scheduled for the sears repairman but am exploring other options.
@@TheDroppedAnchor Yes, inconvenient! I will say that Sears does a good job installing the compressor, mine has been working great since the install. Do what you need to do, I think I waited two weeks and bought an ice chest to help keep food closed.
It's $600 and up if you get the compressor for free. But even if you do, they're still charging you full price like it wasn't covered. A local guy here will do it for $800 total. Parts and Labor. The compressor is $330. So the rest is labor, freon, solder, butane, and that stupid $125 control board updater. I'm so glad I didn't buy the 5 year extended warranty. Mine broke down 6 months after it would have expired.
Im going to replace my compressor and filter dryer, but not understanding something. Mine comes down the back, and its pinched off. Not sure how that works... Ive done home A/C units and tons of auto units but first fridge. Just not understanding why its not inline and is just off to the side pinched off. Damn thing is only a year old and it quit already.
I don't have a Kenmore elite I just have a regular Kenmore refrigerator is this installation guide the same for a regular Kenmore refrigerator which is an older model
@Saint Anger Yeah. They did. But the freezer is still messing up. Goes to 0 degrees sometimes then back to 20 degrees. Tech is coming out today for the 3rd time.
@@TheFrenchPug I was supposed to have the tech come by today for mine and they claimed that he had a family emergency. I would fix it myself but that would wave the warranty
Very good video, BTW do you know why compressors on fairly new and good branded fridges go bad? What are the common causes for this? I think compressors are built to last normally. Thanks.
All new stuff is like this. Only one answer: Cheaply made in China, Mexico, etc under poor QA. I love old stuff when company took pride in their products. Nowadays it is all about profit. Nothing lasts… from cars to electronics to furniture to whatever you can think of.
@@vcubed7275 You nailed it! Great answer. If you can find something made in the 70ties or 80ties it will outlast any thing out there. We bought a new samsung microwave. It was worthless one week after the warranty expired. I will never buy another samsung anything.
@vcubed7275 not only is the craftsmanship poor, but the new age repairmen really don't know their craft. One or two test and they say you need a new computer board or buy a new fridge. Hard to find people like the poster of this video. My fridges compressor is out and only 3 yrs old 😢
It isn't poor craftsmanship, it is specifically designed to fail. I tore apart three Copeland compressors and they all had the same failure, so I reached out to the company and told them, hey if you make this part more durable the compressor would last a lot longer. They said, we know. They want it to fail so you need to buy another one.
You’re not located in South Carolina are ya? 😂 I can’t figure out what’s wrong with my fridge. Everything seems to be working but only warm air blows. Probably compressor is shot eh.
Bro sort of brazing you could have used stay Brite 8 with some flux😊 and you didn't say what kind of torch do you use I guess acetylene b tank but I see you use brazing rods😮 and you should mention the filter dryer goes on the liquid line AKA skinnier line😊 other than that great job
@@seasidescott The connections at the compressor were soldered while exposed to oxygen internally. You've provided zero evidence that oxides did not form internally, which happens in 100% of cases where no oxygen purging takes place.
@@tommygoldman05 Thanks Tommy. So you mean using the nitrogen to flush the lines, I take it. To blow them out. Probably especially when you have those long capillary tubes. But won't the oil just get spread out to later puddle up again and create blockage later?
@@randallsemrau7845 Density of air at sea level 1.225 kg/m³. Density of nitrogen 1.165 kg/m³. Density of 134a 4.25 kg/m³. Nitrogen has 1/4 the density to prevent intrusion of oxygen whose density is 1.429 kg/m³
Why we need to update software on the control board? There is no communication between the board and compressor. It's just copper wings inside and mechanical part.
did you notice that Kenmore is now made by LG in this video ? Kenmore is no longer a premium brand. LG and Samsung get terrible reviews for their refrigerators for bad compressors.
When you checked for the amount of R134a in the first refrigerator that you open was full of food. The last refrigerator that you showed when you opened it was completely empty. What's up with that? Why are you showing a different refrigerator?
I bought a house and it came with old refrigerator, washer and dryer and a fairly new piece of junk LG dishwasher. Guess what causes the most trouble my newest appliance my dish washer? I am keeping my older applainces until they die. Funny, I know seller gave what they thought was junk applainces.😂 Maybe the dryer was junk because it died but my inlaws gave me a free old dryer. I have lived in my house for 4 years and still havent had to pay to replace any appliances.
Yes this true I had a tech out called a local guy to come look at it and he came in and said you need a new compressor right out the gate I ask how much is that I just replace my compressor in my truck 2 days ago cost a bit but he said $1200 but there’s a class act lawsuit and your compressor will be free if you call this number 1-844-553-6667 called and there schedule to come out Friday and there comping me for food loss as well not sure how much yet but ok I will take it I have the same kenmore in this video. I could do it myself but let them handle it. I don’t have the new program to flash the update but the rest is easy. But the service guy that came out was cool he was here 1min 38 sec. I told him I appreciate the honesty he could of straight ran the numbers on me and don’t have to tell me about the lawsuit and I was ready to get done ASAP. I told him I’m going to pay for his time he was good with $20 bucks is what he changed me. I gave him $20 bucks and a HOT BEER lol naw I had cold beer in the other fridge. Thanks to good people out there. Anyone that has a problem call the number and get it free
@@levitate9128 did you have to show them proof of purchase?? thats what they’re asking me for and the person that gave me the fridge doesnt have it anymore
@@anapaz9390 no I didn’t have to show them any proof of purchase and no questions asked. They know these compressor are Fup and there replacing a bunch of them but I will tell you this I still haven’t got mine fix yet but the parts are coming in the mail everyday just waiting of one more thing there gutting the whole system and replacing everything. But I found out Sears will not pay for the labor all parts are payed for but not labor. Labor in my area it’s going to cost me out of pocket about $475.00. And I can also tell you this LG had the same compressors in them and LG is paying 100% for parts and Labor. I found a LG refrigerator on Facebook for $100 that had the same problem as mine call LG to about and there also gutting it and replacing everything in it as well 100% covered and I didn’t have to prove anything to them not proof of purchase all the asked me is when I bought it I told them 3 years ago and they said ok we will cover it. The only thing is look at the date in the LG refrigerators for the date longs it’s not passed 4 years old it can be maybe few months pass 4 years maybe 6 months passed and they will still cover them 100%. So when I found this out about LG I bought 1 off the Facebook market for $100 and called them and service guy was at the door next day and there replacing all the gutts for free no out of pocket to me but the $100 and me picking it up (Winning) on that end
@@thebotlobbydaily thanks , I have the Kenmore elite model as well and it just stopped cooling , was bought from Sears , would they be able to replace it as it has been around 6 years since I had bought the unit?
Thanks for the confidence boost. Compressor is on the way and I'm buying a new filter dryer.
Hi, 20+ years as an appliance tech and 10 as hvac tech. Question: Why didn't you fill the system with nitrogen when checking for leaks? Had you found a leak, you would've had to recover all your refrigerant to fix the leak. I've always done it that way... I realize your way is faster IF there are no leaks. But if there is a pinhole leak in the solder, the nitrogen can just be quickly vented into the atmosphere, then you fix your leak, and then put fresh refrigerant in.
Less experience lol
This is how I was taught. Not only that, itll flush contaminants out as well.
@@ajcastellon5903 nice job 👍🏼
Never did small apliance but i was tought if it pulls below 500 and holds theres no leak. I mostly use Nitrogen during braizing
I have an issue on Bull outdoor mini refrigerator, with 600a, 1.02 Oz of charge , which tool would i need to buy to check the charge pressure ?
Our compressor was still working so brazed on a valve and replaced R134a (it's only 5 oz which is less than half a can you can get for automotive AC) and it's been working well for the last month.
my compressor is still working too, i have bullet valves and gauges coming tommorow, im hoping thats all the issues
@@devoncrampton5223 Using the gauges for high and low is usually a waste of time. What matters is the weight of refrigerant you put in.
@@seasidescottonly it’s not. You add the weight (or not) depending on your pressures.
Excellent video. Thank you.
Does it matter what direction you put the filter drier ? Or is there an arrow for flow ?
excellent video and very detailed and professional.
That sure is correct..
When you work on dual evap LG's which Service Manuals do you use> The one I downloaded from the internet for my LFX31945ST does not have the correct info for checking or replacing the Ref compartment evap fan , it only refers to a single evap system and the fan in the freezer for the ref. compartment. Is there any supplement pages for this manual I could find? Keep up the great videos and info you provide to us.
How long are those hoses for your gauge
Thank you for sharing this video...I have the exact refrigerator and the compressor has failed. It is under warranty, but it is good to know what will, and should, be done. Thanks again!
How long did you have your refrigerator before it failed? I have this exact same fridge as well. Have had it for 7 years now. Just died yesterday. Such a great fridge too.
@@ErichCervantezthese are lg linear compressors....they are lg science projects that have really bad service life. If your replace it tap condenser fan com lines and use relay between them and a standard compressor.
We had this fridge. It also failed. Garbage.
They all fail on this fridge. Ours did too
Where did you get the update program and device to upload the updates? Is it available to buy?
Excellent video SR thanks
Hello, was it not necessary to use the system updater?
i have daewoo frs 2021IAL, compressor need to be replaced, if we replace the compressor with the new one will it work or need any programming for PCB?
what brand refrigerator do you recommend?
Hi how are you? i have a question if i have the same old compressor 220v 60hz R134a inverter GL and i wanna buy a new one but not inverter. Which compressor you do think is good ? Thank you!
I need this done for a fridge I have. How much would it cost if I have the compressor I only need the labor and the valves. Thanks great video.
Could you provide part # for filter drier please? The one I purchased has ends that are too small in diameter.
Great video...wish I HAD all the tools you do! LOL
Did you go from a FLB075LBNA to a FLS075LANA? Compatible?
How much did you charge dollar wise?
Is that an oxy acetylene torch?
So two of the compressor lines are NOT copper?
Needs flux then?
So An FLB075LBNA can be replaced with an FLS075LANA ?
❤ superb video all around.🎉
Thanks for the great video! Sealed System work is the ticket$$$ I'm learning.
In regards to the software update, is it with the LG software rewriter kit? Given the fridge is a Kenmore fridge is it correct to get the LG software update? Our compressor just went out it’s an LG compressor in a kenmore fridge and the sites all say our compressor has been replaced by a newer model but it also requires updating the software with the LG software rewriter…doesn’t make sense to me since the fridge is a kenmore fridge
LG made the Kenmore Elite (total crap) refrigerators when they sold them.
Did you use 95/5 SoLDER
Very nice video thank you very much
Good work. THank you
two questions... 1) which way should the arrow on the filter dryer be facing? 2) which version of the JIG is used for this compressor?
If you’re using a drier with an access point, the side with the access point always goes to the Yoder loop. But you always want the arrow on the drier going the same direction as the Yoder loop. If reversed it’s probably gonna clog
I have another dryer on the intake line....the copper line on the bottom there is a small copper "can" that looks like a short fat version of the dryer you replaced. It sort of resembles a fuel filter. I didn't see you replace that.
how did you figure out it was compressor issue
great sytem, any update?
Bravo , 🇪🇸 saludos Spain.
No reprogramming the board so the compressor runs correctly?
I have the same POS model fridge and will need my compressor replaced. The compressor is under warranty, but the labor is not. How much do charge to do the replacement?
$600 on up. Sears will screw you.
I just got a quote from Sears for $1327.26 compressor and drier replacement. 5yr old Kenmore
I have that same POS fridge! The compressors are made by LG, and they are known pieces of garbage, yet they continue to sell them for top dollar with a useless warranty of just one year. There have been class action lawsuits and their solution is to just keep selling them but limit the warranty so they aren’t responsible for the service bill (about $1,000).
Never buy LG, Kenmore, or Samsung appliances.
Kenmore used to be an excellent brand refrigerator until the company went out of business about 10 years ago. LG knew their fridges was junk so they bought Kenmore's name and started relabeling their junky fridges Kenmore, smart on their part but bad for the consumer (very unethical). Samsung fridges do has a lot of problems.
@@easyon12 exactly! 👌
Agreed.
My upright freezer compressor is running supee hot and not in a freezing mode. I have replaced the start device.. Nothing. I have try the 3n1.. Nothing.
What could be the problem?
I need to change Kenmore invertor Compressor LG FLB075LBNA so if I'm changing compressor with the same series than I still have to change/install the software?
Did you ever figure this out?
Hi Technician, can you install the LG linear compressor to my Kenmore Refrigerator?
Unfortunately no
Thanks , how much would such a repair cost and any guide to diagnose as I have the same model , compressor seems to be working but no cooling , can’t seem to diagnose the issue before replacing or going for the big repair , appreciate any help , thanks
I have the exact same model and problem. The compressor comes on, the fan to the right of the compressor turns on as well. The fans inside the unit are blowing, but not cold enough. I'm sure you heard about the LG compressor recall? The Kenmore uses this LG compressor. It has 5 year warranty for the part, but not the labor to put it in. This guy says it's easy if you have the tools. Yeah, most average people, me included, do not have the tools used in this video.
What happens if I don’t update the main board when installing a new compressor?
Controller may cause the compressor to malfunction or shorten its life, TLDR: if it needs it, always do that step.
Where you located?
Where are you located?
No micro gauge? How do you know you have a dry system? Or do you know what a dry system Micron reading is?
500 microns?
If you don't have a micron gauge vacuum for at least an hour
How do I eliminate the inverter compressor, rather just use my nice French door fridge with a 120v r134a compressor ....I do commercial hvac...so I'm up to the task...any guidance of how to.eliminate the board or use the hoard to call my 120v compressor to come on...thanks
how do you know the compressor not working
Should have brazed service port then trickled Nitrogen and finished other joints. Pressure tested with dry nitro then vacuum.
Should coulda wooda.....it's a refrigerator....this will work just fine. Not a space shuttle.
Nice channel! By the way did you have to update the board?
Yes, it's recommended
What kind of brazing rod do you use?
sil fos 5% or 15%
I’m a residential hvac guy. I’ve never seen flux used when brazing. Granted I’ve always done copper to copper.
What kind of flux is he using here?
Can you provide a list of everything that you used. As if you were telling someone what to buy if they wanted to go into changing compressors?
Hello, did he leave a
List of all the tools etc… he used
I want to buy those items my son and I fix friges and freezers
Shouldn’t you compress it with nitrogen and do a sweep charge first?
That video is well done! However, after watching, I h scheduled an appointment with Sears to replace my Kenmore Elite Refrigerator compressor.
So much for elite huh...im watching this video because our 2015 Kenmore Elite compressor failed today. If I may ask, how much was the repair for yours? Im trying to get an appointment scheduled. Thanks!
@@rbljackson A 2015 Kenmore, Great Refrigerator and worth replacing the compressor! The compressor unit is expensive but covered by a 10- year warranty. Installation was about a 1,000.00, but the service guy suggested I purchase a Service Contract and the repair would be about 400.00. I entered the Sears Contract for 50 per month which covers all appliances. After 30 days the contract is cancellable, however, my refrigerator ice maker is broke and that was covered by the contract. I recommend getting that compressor replaced as the newer units I looked at just are not as good as that Sears Elite. It did take a couple of weeks to get the service done, in the meantime, I purchased an ice chest to keep food cold. Yes, an inconvenience, but it all worked out!
@@paulkoscheka4434 I heard that one person canceled the Home Warranty after a couple months and they went after her for the full amount of the discounted repair.
I just got off the phone with Sears. I will have to wait two weeks for a repairman. The monthly cost of the home warranty is $65 a month.
I scheduled for the sears repairman but am exploring other options.
@@TheDroppedAnchor Yes, inconvenient! I will say that Sears does a good job installing the compressor, mine has been working great since the install. Do what you need to do, I think I waited two weeks and bought an ice chest to help keep food closed.
I have that same refrigerator and I have to change the compressor. I live in Miami, they don't have a team working here!
Another company is honoring and servicing these units to continue to gouge every customer possible. This has happened to every single one they sold.
The LG compressor has a law sue going on, you don't know how long will that last by replacing the same LG model.
Is that worth it?
There’s universal compressors that replace the oem compressor
No oil?
I'm accustomed to cars. Those are larger systems, but I expected some oil aside from any that is already in the new compressor.
can i solder instead of braze?
I don't know...can you?
Pl do double brazing of pipe
What does a typical compressor replacement cost?
These are $800 and up.
I just picked up a Kenmore elite for 100$. It needs the compressor, dryer, and charge!
Did you ever get that done, if so how much?
It's about $1000 to get done.
Hi great video. How much do you charge? I have a Lg and have to get the compressor replaced. Thanks
I asked the same question with no response
I asked the same question with no response
It's $600 and up if you get the compressor for free. But even if you do, they're still charging you full price like it wasn't covered. A local guy here will do it for $800 total. Parts and Labor. The compressor is $330. So the rest is labor, freon, solder, butane, and that stupid $125 control board updater. I'm so glad I didn't buy the 5 year extended warranty. Mine broke down 6 months after it would have expired.
Good video, very informative.
FYI the background music is kinda loud and distracting. 😊❤
There's no question about not replacing filter dryer. You always replace when replacing compressor.
Im going to replace my compressor and filter dryer, but not understanding something. Mine comes down the back, and its pinched off. Not sure how that works... Ive done home A/C units and tons of auto units but first fridge. Just not understanding why its not inline and is just off to the side pinched off. Damn thing is only a year old and it quit already.
@@motorcitywestauto4674 it's probably coming back in from the Yoder loop
What's the cost for replacing compressor?
$800
How much does it cost to get it replaced?
$800-$1100 parts and labor.
You forgot to clean the condenser and blow through the high side and clean out through the suction line as well
I don't have a Kenmore elite I just have a regular Kenmore refrigerator is this installation guide the same for a regular Kenmore refrigerator which is an older model
No. Kenmore Elites are made by LG. Different system. Crap!!! Mine just went out after 5 years.
@@TheFrenchPugyou know they will cover the parts just not labor @ LG not sure about Kenmore but it should be the same no?
@Saint Anger Yeah. They did. But the freezer is still messing up. Goes to 0 degrees sometimes then back to 20 degrees. Tech is coming out today for the 3rd time.
@@TheFrenchPug I was supposed to have the tech come by today for mine and they claimed that he had a family emergency. I would fix it myself but that would wave the warranty
Vacuum with core remover tool with Schrader out causes restriction on your vacuum
Whats the price to change out a compressor just like that one???
My Elite refrigerator compressor has failed after four years. I've been told it's $8-900. I do know the compressor itself is $375
How can I get that device To update the software.. where can I purchase it ?
From LG. It's $125.
Shout out bos..❤️
How come ypu only add charge through low side?
That is the way to charge almost any system
Isnt it not worth doing this?
How can I get your service ? I stay in Houston
Still looking for service?
Very good video, BTW do you know why compressors on fairly new and good branded fridges go bad? What are the common causes for this? I think compressors are built to last normally. Thanks.
All new stuff is like this. Only one answer: Cheaply made in China, Mexico, etc under poor QA. I love old stuff when company took pride in their products. Nowadays it is all about profit. Nothing lasts… from cars to electronics to furniture to whatever you can think of.
@@vcubed7275 You nailed it! Great answer. If you can find something made in the 70ties or 80ties it will outlast any thing out there. We bought a new samsung microwave. It was worthless one week after the warranty expired. I will never buy another samsung anything.
@vcubed7275 not only is the craftsmanship poor, but the new age repairmen really don't know their craft. One or two test and they say you need a new computer board or buy a new fridge. Hard to find people like the poster of this video. My fridges compressor is out and only 3 yrs old 😢
@@vcubed727510000000% true
It isn't poor craftsmanship, it is specifically designed to fail. I tore apart three Copeland compressors and they all had the same failure, so I reached out to the company and told them, hey if you make this part more durable the compressor would last a lot longer. They said, we know.
They want it to fail so you need to buy another one.
You’re not located in South Carolina are ya? 😂 I can’t figure out what’s wrong with my fridge. Everything seems to be working but only warm air blows. Probably compressor is shot eh.
Bro sort of brazing you could have used stay Brite 8 with some flux😊 and you didn't say what kind of torch do you use I guess acetylene b tank but I see you use brazing rods😮 and you should mention the filter dryer goes on the liquid line AKA skinnier line😊 other than that great job
No nitrogen purging before soldering? Guaranteed service call in 5 years, right?
no, the system is quite small and with a hot torch seals quickly, compressor comes purged so no residual oxygen within.
@@seasidescott The connections at the compressor were soldered while exposed to oxygen internally. You've provided zero evidence that oxides did not form internally, which happens in 100% of cases where no oxygen purging takes place.
Its also a good idea to purge with nitrogen because that system gets clogged with oil when the compressor goes
@@tommygoldman05 Thanks Tommy. So you mean using the nitrogen to flush the lines, I take it. To blow them out. Probably especially when you have those long capillary tubes. But won't the oil just get spread out to later puddle up again and create blockage later?
@@randallsemrau7845 Density of air at sea level 1.225 kg/m³. Density of nitrogen 1.165 kg/m³. Density of 134a 4.25 kg/m³. Nitrogen has 1/4 the density to prevent intrusion of oxygen whose density is 1.429 kg/m³
How much do u charge for this?
$1100
It looks like you might want to answer some of the viewers questions...!??
How did you make such a short flame coming from the torch? Mine keeps burning the surrounding area in the fridge.
You have to get a different size tip.
Nitrogen will purge any partials in the system! A must have doing sealed system work !
Why we need to update software on the control board? There is no communication between the board and compressor. It's just copper wings inside and mechanical part.
I thought I saw an electronic switch on the side of it. Something has to control the compressor turning on and off like your AC, no?
did you notice that Kenmore is now made by LG in this video ? Kenmore is no longer a premium brand. LG and Samsung get terrible reviews for their refrigerators for bad compressors.
Kenmore Elite made LG not the Kenmore regular.
I cannot find anyone in the repair buisness to replace our compressor. We live 30 minutes from Buffalo,NY
Did you call Sears? They'll gage you but they are the ones who sell these.
795 & LGs suck but they keep us busy.
LG should be covering the labor you fix these since it's every single one of these that they sold. Not just a small percentage.
can Anyone please tell me copper to copper Filler metal name and copper to Aluminum Filler name?
Silfos 15 for copper to copper
Test for leaks 1st with nitrogen then vacuum
Correct!!!
When you checked for the amount of R134a in the first refrigerator that you open was full of food. The last refrigerator that you showed when you opened it was completely empty. What's up with that? Why are you showing a different refrigerator?
I bought a house and it came with old refrigerator, washer and dryer and a fairly new piece of junk LG dishwasher. Guess what causes the most trouble my newest appliance my dish washer? I am keeping my older applainces until they die. Funny, I know seller gave what they thought was junk applainces.😂 Maybe the dryer was junk because it died but my inlaws gave me a free old dryer. I have lived in my house for 4 years and still havent had to pay to replace any appliances.
Why does this fridge compressor fail all
The time.
How much for a tech to do this kind of job
1800
This make NO sense why don't THEY just get a new fridge!????
How much this job cost for everything ?
500-1000$
Invest in a tripod. Awesome me duzzy
You no people ln Corpus Christi repaid that
Flux on your solder joints is strongly recommended, that service valve is too long! You should not have to bend it.
If you need a 1706 hit me up.
Ruff work
$1100 parts included in case you’re wondering I just got a quote right now
A Lawsuit was successful on lg compressors going out on refrigerators
You should be able to get one for free
We replace several weekly
Yes this true I had a tech out called a local guy to come look at it and he came in and said you need a new compressor right out the gate I ask how much is that I just replace my compressor in my truck 2 days ago cost a bit but he said $1200 but there’s a class act lawsuit and your compressor will be free if you call this number 1-844-553-6667 called and there schedule to come out Friday and there comping me for food loss as well not sure how much yet but ok I will take it I have the same kenmore in this video. I could do it myself but let them handle it. I don’t have the new program to flash the update but the rest is easy. But the service guy that came out was cool he was here 1min 38 sec. I told him I appreciate the honesty he could of straight ran the numbers on me and don’t have to tell me about the lawsuit and I was ready to get done ASAP. I told him I’m going to pay for his time he was good with $20 bucks is what he changed me. I gave him $20 bucks and a HOT BEER lol naw I had cold beer in the other fridge. Thanks to good people out there. Anyone that has a problem call the number and get it free
@@levitate9128 did you have to show them proof of purchase?? thats what they’re asking me for and the person that gave me the fridge doesnt have it anymore
@@anapaz9390 no I didn’t have to show them any proof of purchase and no questions asked. They know these compressor are Fup and there replacing a bunch of them but I will tell you this I still haven’t got mine fix yet but the parts are coming in the mail everyday just waiting of one more thing there gutting the whole system and replacing everything. But I found out Sears will not pay for the labor all parts are payed for but not labor. Labor in my area it’s going to cost me out of pocket about $475.00. And I can also tell you this LG had the same compressors in them and LG is paying 100% for parts and Labor. I found a LG refrigerator on Facebook for $100 that had the same problem as mine call LG to about and there also gutting it and replacing everything in it as well 100% covered and I didn’t have to prove anything to them not proof of purchase all the asked me is when I bought it I told them 3 years ago and they said ok we will cover it. The only thing is look at the date in the LG refrigerators for the date longs it’s not passed 4 years old it can be maybe few months pass 4 years maybe 6 months passed and they will still cover them 100%. So when I found this out about LG I bought 1 off the Facebook market for $100 and called them and service guy was at the door next day and there replacing all the gutts for free no out of pocket to me but the $100 and me picking it up (Winning) on that end
@@thebotlobbydaily thanks , I have the Kenmore elite model as well and it just stopped cooling , was bought from Sears , would they be able to replace it as it has been around 6 years since I had bought the unit?