Pt.2 ATV CV Boot Replacement At D-Ray's Shop
Вставка
- Опубліковано 6 жов 2024
- All modern ATVs use CV shafts in one form or another, this Yamaha 660 Grizzly has a total of ten! They are easily torn, and if left un checked will ruin the CV joint. They are not hard to replace, as you will see.
Thanks for watchin' Don't miss Parts 1 and 3
I created this video and I own all rights to all content in the video.
Music provided by : Kevin MacLeod incompetech.com...
Name of tune "Cold Funk", and "Delay Rock" Kevin MacLeod (incompetech.com) Licensed under Creative Commons "Attribution 3.0" creativecommons...
Ray, you did an excellent job of how to, from start to finish
Thanks D. RAY,,,,,,,, very professional presentation, without all the UNNECESSARY ANNOYING MUSIC.... I can hear you clearly and see what you were doing.
Mr. D-Ray....I found your instructional very informative and easy to follow along. Thanks for such a positive attitude and enthusiasm that makes you listen even if you don't have a project. Enjoyed sharing with my 17yo son without tensing waiting on the next group of curse words to being blurted out. Great work! 5 ☆minimum, more like 10!!
Where do your recommend buying Honda ATV parts?
If you're worried about your 17yo hearing curse words at that age you're setting him up for a lot of bigger problems later on in life.
As far as I am concerned, you sir are a frickin surgeon.
Like the fact that you started working on a clean ATV with no mud or dirt on the axel as it makes it so much clear for us amateurs to observe and learn. One Q...what did you use to remove and clean old grease?
perfect I like the whey you show every step. thankyou very informitive
Great and helpful video. I would not reuse either boot if I went through all that to take it all apart. I figure if one boot is gone the other must be close to going.
not if you ripped it on sticks
Same here! If I'm going that far it'll all be new when it goes back on!
Great video build of the cv boot repair! Your instructions are clear and understandable, thanks!
Great vid D-Ray.If you teach Gods word the way u explained the cv axle repair oh boy.
Great video!! it really helped me replace my c.v. boot's..would have been tough without your help..thanks..
D-Ray, great video… very helpful
Thank You!
Great tutorial. I just replaced my axle cause I did t know how to do this. Could’ve saved a pile of money
thanks Jason , that was very helpful because I am working on a Yamaha wolverine right now.
Other then some difficultly removing the inner bearing without use of vice, all went well.
Great demo! thanks..
Excellent video. Everything is explained quite well.
That's what the doctor ordered! Thanks a lot for your sharing.
Thanks great video. I wish I could understand what made 44 people dislike this video. How can you dislike something made to help people.
Top notch vid, many thanks
Excellent job explaining everything in detail. I'm hooked
Awesome Video D-ray. I have a torn boot and the cv started clicking. How easily are the CVs ruined? is it something you can clean, regrease and reboot and be ok or is the cv ruined pretty quickly if its not taken care of immediately? Great Video by the way. You do a great job explaining all the little things to look for when doing this job. Thanks
thank you D-ray ,it was very helpful your video !! i have SYM 600 quadrider i'll use your informations ....
D Ray, i just pull the bottom shock bolt and the bottom knuckle nut then the axel comes right out. Alot faster
Thank you. You make it look easy!
Best video on this subject... thank you!
Very informative and attention to detail video! Thanks
Thanks a lot from France, i was very interesting by your movies. instructional are very informative and i can do that now on my engine. thanks for your time to make that.
These videos were so much help. Thank you for sharing!
Honda Rancher, 2010 front axle. Can't remove or slip the beirngs race off. Pounded it with a 2x4 with no luck.
Thanks mate! (from Australia).
Your Videos are always Super Helpful Keep up the Good Work 👍 Cheers 🍻
Excellent attention to the details...Helped alot, Thanks
Super great video
Why worry about if you get grease on the inside of the boot. The grease will eventually work it's way off where you placed it and onto the boot?
great video. very good on the camera.
Looks like a brand new one now :-)
Nicely done mate :-))
are there after market cv boots for Kubota RTV x 1120D If yes, where--thanks for excellent video
Great instructions , thanks 👍
this video is very great ,thanks man.
It appears our bearings may be toast. They are falling out of the chase, or is this normal?
Thank you for the video good sir
Great Video thanks D -Ray!
thank you so much
Awesome video!
Thanks for such detailed video
Great videos. What do you use to clean the grease from the old boot?
Brake parts cleaner and rags in a box works well
Excellent video sir thank you job well done
Thank you! I'm definitely subscribing and liking this video.
Very good video, thanks.
Thank you
THanks Man , Great video
good video my name is mark for a person like me that has never done this how are is this to do mark
Ray, How is it your inter joint race and bearings stayed together, my ball bearings fell out all over the table when I removed them from the inter joint cup.. what did I do wrong ?
Good video man
Fantastic videos, man!
Excellent!
thanks for putting out the video ... ! question got a catvo 6 inch lift eagle turner axles cv boots getting to hot destroying the boot is there better grease ? or can I simply put in more grease ? any ideas ? again thanks for the video
Didn't look like you got clamps very tight. Know wonder they spin if grease gets on them
Thats right. I noticed it also, need to throw them into the garbage for one thing & get the notch clamps.
I would & have used 75lb zip-ties many times, much better than these pull through & fold overs. He at least should have pulled them tight with a vice-grip then fold.
This was very helpful Thanks
super bueno el video asi es que nesesitamos un profesor
D-ray would feel safe with re using those fold over clips?? Any tips for rebuilding all four on a fourtrax 300?
As long as the little lock tabs are good, I have re-used them. Aside from the brakes, the procedure for your TRX300 will be almost identical.
D-ray is that a 4x4 fourwheeler your working on in these videos?
Nice job !Thank you !!!!
Please, can worn-out or bad inner cv joint cause ABS light on? I asked because immediately I changed the cv axle joint, I began to hear like cracking nose. Please, what could be the problem?
exelent .....very didactic thanks
great vid thanks
How do I get the cv axle out of the rear plunging joint on a 2003 Polaris Sportsman 700 Twin? There's no retaining ring, and it doesn't seem to rock far enough to release the balls.
thanks
Where did you get your boot kit from?
The longer ye live the more ye learn.
Is this the same process for a Honda foreman?
I think I’m gonna repair my old axle for a spare
you don't have to use a clamp tool?
Could I use hose clamps?
the best
Can someone tell me if it matters how the c-clips are facing
epic
Don't u use tool to
^
Dude you rock! Thanks!
You didn't even pack the bearings though
Very nice instruction. Thanks!
Great video !!
thanks
thank you