The MTW wire is a pleasure to wire panels with. Converted 9 Grieve truck ovens from bang bang contactors to plc proportional control years ago. Very satisfying work.
It's easy when you have a proper service cabinet with all the lacing fixings. Experts challenge I just did. A quad 4x4 box. 3 receptacles and a 3 way switch. Box was also a junction feeding three downstream conduits plus the lighting traveler, all wired with 12 gauge. Took me a solid half hour to stuff it so I didn't have to cram the faceplate on.
Well,did you measure the contact pressure of the wires??You always have to do that to make sure the contacts are good!So in the future the contacts will not come lose..Further you dont measure the length off the wires,you just cut it off on one end and the other end.Wasting a lot off expensive wire!
Hello my friend You are right Wires are expensive But measuring them is very time-consuming and increases the cost of wiring. This saves time and the costs are also different because we use the cut wires elsewhere and it is not wasted
@@IET-76It doesn't have to be time consuming!Just connect it to one thing and lay it out to the other thing,and then cut it off long enough.Do not connect.Then al the others this way and then measure the real length and cut it off and connect.So then when you connect you only cut the wire there to the length.That means that you only waist on one site the length off the wire and not two times!!Easy!!☺☺
Ahh just seen a comment that indicates this is a usa panel....company i worked for in UK did a lot of work on york chillers from us, the panels were removed and a new uk spec one fitted.
@@mindaugasv85 take it you have never been a maintenance electrician called out to fix a fault on a control panel with a comment like “don’t see the point in line diagrams” or are you being sarcastic 😂
Why is the three phase rccb connected to city electricity terminal box? How would it get emergency supply as you have given it input from the red terminals, not the selector switch output?
When the selector switch is in position 1, the power enters the rccb switch from the red terminals, if it is in position 2, the power enters the rccb switch from the gray terminals.
What do you base the choice of spacing between ducts and rails on, do you choose an arbitrary distance? Do you calculate something? Do you follow some rules?
Hello. According to my experience, the distance between the ducts in the case where the miniature switches are installed inside should be 13 cm. The distance between the ducts in the case where the contactor and current controller are installed under them should be 18 cm. also. The distance between the duct and the end of the rail in the lowest row should be 6.5 cm. Please ask if you have any other questions.
Brown, not red, but yes, that's usually the case, in domestic and commercial wiring. This, however, is an industrial panel, and in my experience you most often see the wiring inside panels like this being black for phases; But really, any color wiring except green/yellow is permissible in most regulations, and blue is only inadvisable but not outright banned.
Striping wires in minimum & proper length , securing connection by tightening the screws with their specified tool, Colors scheme in wires help in easy identification for connections. Central Bar rail which allow each wire pass through desperately & accommodate it's bit extra length that might be its farther use is very nice. However ,Labelling them all individual components in Panel would surely helpful and good in education point of view. It would further improved by verbally describing the function and purpose of each component in single line. Using proper tools for the purpose ensure the life and longitivity. Thumbnail for Practical demonstration and deserve
@@IET-76 no I mean normally in the European and UK markets all wires must have a number on them. This is shown on the schematic so you can easily identify each wire.
@@IET-76 same with the panels I build, it is for my benefit that I avoid cutting my fingers during the build, but once completed, it will be restricted access
That socket towards the end seems... Weird. It has grounding pins, but no grounding wire connected, and no grounding screw either that I could see. Seems a bit unsafe tbh.
Are you not using Red, Yellow (or White) and Blue for Phases, Black Neutral and Green (or yellow/Green) for earth. Are you switching the Neutral. That's a fail in New Zealand or Australia.
No cables identified,no id on componants,no shrouding on isolator and not door intrlocked. Self tappinf screws through back of panel and sides of panel....perhaps not done in uk.
I don't know bud, I'm a level below this, I'm struggling to even read what the inputs for the wires are supposed to be... N= neutral, ph=phase? auto=?? C=? NC and NO? So... I guess you wire it if you want the contactor to be normally open or normally closed I guess? I mean it's a good effort and the camera quality helps a lot but I'm still a level below this, hard for me to understand. Need to watch the video a few times and others...
Hello my friend. Watch the video a few times. There are also other videos in this channel that talk about all the equipment needed for the electrical panel and all their details can be explained by watching them. You learn more
OMG I used to build a few panels for control jobs why did I not think to use self drilling screws instead of drilling and tapping holes 🤷♂️🤬. Surly you are not mounting the components directly onto the back of the panel though, panels are normally supplied with a steel backplate to mount on
Thank you for your opinion. It was very helpful. But I must say that in this area the conditions are such that you have to draw the electrical panel in this way. Good luck.
Good job, but this panel will not pass US National Electrical Codes, firstly, the panel space is small compared to the number of devices used, a neutral wire is used along the length of the panel, which must be used separately from the busbar, the panel is not grounded, And there is no ground terminal, it is not allowed to install the outlet on the panel body, the wires and terminals do not have address numbers, the main switch is not installed in the right place, and it is not insulated and covered...
That’s an interesting comment. Why is the panel too small, there is ample space for the small amount of heat generated as it only appears to be a 30 amp supply at most 40. The last comment about insulating and covering is even more so, it’s all what we would term fingerproof ( ipx2 I think it is) having watched a lot of electrical videos from your country I am horrified by the amount of exposed copper. I am not having a go, just curious for an explanation
Thank you for your opinion. It was very helpful. But I must say that in this area the conditions are such that you have to draw the electrical panel in this way. Good luck.
The MTW wire is a pleasure to wire panels with. Converted 9 Grieve truck ovens from bang bang contactors to plc proportional control years ago. Very satisfying work.
Thanks for filming and sharing - saw many "panelboards" of this style in Italy - soo different than the factory-made panelboards in the US.
Great video, learned a lot so far. Just subscribed and can’t wait to watch other videos you have.
Thanks for helping man.❤
Work with panels for 5 years. best work i have in electricity area.
It's easy when you have a proper service cabinet with all the lacing fixings.
Experts challenge I just did. A quad 4x4 box. 3 receptacles and a 3 way switch. Box was also a junction feeding three downstream conduits plus the lighting traveler, all wired with 12 gauge. Took me a solid half hour to stuff it so I didn't have to cram the faceplate on.
Thank you for this amazing tutorial ❤
Tanks
did you drill with the bolt/screw directly instead of a pilot hole with a drill bit, tab it then install a the screw
Hello These are self-tapping screws and they pierce the iron sheet and are fixed in it
Wearing industrial electrical panels that are very detailed operation, very good ❤ 26:20
Thanks
به لجه ات و محیط میخوره ایرانی باشی. ایول کارت درسته 👍
Merci. Tashakor
اونجا من دوره دیدم کار کردم کارشون عالی بود
Crystal clear sir❤
Good video
❤GOOD
Thank for sharing🥰🥰🥰
You are the best
Thanks
Good work.. I am electrical company Sialkot.. Pakistan country
Tanks
samalah bro...nasib saya pun selalu sial kot 🥺🥺
Good ❤❤❤❤
Very nice wiring
Tanks
Thank for the video, i didn't see the ground bar in you panel?!
I use rccb switch instead of ground
Thank you for sharing!
Tanks
Well,did you measure the contact pressure of the wires??You always have to do that to make sure the contacts are good!So in the future the contacts will not come lose..Further you dont measure the length off the wires,you just cut it off on one end and the other end.Wasting a lot off expensive wire!
Hello my friend
You are right
Wires are expensive
But measuring them is very time-consuming and increases the cost of wiring. This saves time and the costs are also different because we use the cut wires elsewhere and it is not wasted
Nobody measures wire ahead of time 😂
@@IET-76It doesn't have to be time consuming!Just connect it to one thing and lay it out to the other thing,and then cut it off long enough.Do not connect.Then al the others this way and then measure the real length and cut it off and connect.So then when you connect you only cut the wire there to the length.That means that you only waist on one site the length off the wire and not two times!!Easy!!☺☺
Make a new video. Your style.
Equifinality.
@@GMshines Sorry,i am a retired electrician..I am 75 years old.
Ahh just seen a comment that indicates this is a usa panel....company i worked for in UK did a lot of work on york chillers from us, the panels were removed and a new uk spec one fitted.
great video❤
Very nice work and usefull video 👍
Have you got multiline diagram for this switchboard ?
What do you mean?
@@IET-76 Some documentation like electrical diagram for wiring
No, unfortunately there is nothing
@@IET-76 I never understood why they need el.drawings for individual projects 😊
@@mindaugasv85 take it you have never been a maintenance electrician called out to fix a fault on a control panel with a comment like “don’t see the point in line diagrams” or are you being sarcastic 😂
does the single phase motors need over current / motor protection relay ? is 1 pole MCB is enough ?
@@ElHytm
The single phsse motors need more current and need load control relay ans phase control relay ans miniature switch
nice to consider air flow between the switches .AFARIN
Thanks
New subscriber always watching your videos😊 many learnings
Tanks
Where should I start to watch your videos as a beginner? Thank you
Hello.you start by this play list
ua-cam.com/play/PL9A4ne0l6hqyx-C--kQxdkH1HUG0XprSb.html&si=iKpW_jqDvATgBEfI
@@IET-76 Thank you very much.
You're welcome
watching this is so satisfying. thanks buddy. I subscribed.
you're welcome
عمل جميل جدًا وفيديو مفيد 👍👍👍
Tanks
ویدئو عالی بود،خسته نباشی👌
Hey friend, could you clarify a question for me? How long does it take to become an electrician in the US?
About 2years but this depends to your try
Why is the three phase rccb connected to city electricity terminal box? How would it get emergency supply as you have given it input from the red terminals, not the selector switch output?
When the selector switch is in position 1, the power enters the rccb switch from the red terminals, if it is in position 2, the power enters the rccb switch from the gray terminals.
Hi
What do you base the choice of spacing between ducts and rails on, do you choose an arbitrary distance? Do you calculate something? Do you follow some rules?
Hello. According to my experience, the distance between the ducts in the case where the miniature switches are installed inside should be 13 cm. The distance between the ducts in the case where the contactor and current controller are installed under them should be 18 cm. also. The distance between the duct and the end of the rail in the lowest row should be 6.5 cm. Please ask if you have any other questions.
@@IET-76 oh i see, thank you
Expert
AMAZING🤩
Tanks
Gonna have to sub
Hey there!! Are you really an electrical engineer🤩🤩🤩? You are really skilled. Good job.
Thanks
Same here but don't know if I can be taken a special tutorial on this pls
Red grey black for the FASES, Blue for Neutral. green Yellow for earth.
Brown, not red, but yes, that's usually the case, in domestic and commercial wiring. This, however, is an industrial panel, and in my experience you most often see the wiring inside panels like this being black for phases; But really, any color wiring except green/yellow is permissible in most regulations, and blue is only inadvisable but not outright banned.
I need more video, nicely
Good job
Thanks
Pls upload control wiring diagram in comments. It will helpful to understand. ❤️🙏👏
Sure
Where are you from?
Striping wires in minimum & proper length , securing connection by tightening the screws with their specified tool, Colors scheme in wires help in easy identification for connections. Central Bar rail which allow each wire pass through desperately & accommodate it's bit extra length that might be its farther use is very nice.
However ,Labelling them all individual components in Panel would surely helpful and good in education point of view. It would further improved by verbally describing the function and purpose of each component in single line.
Using proper tools for the purpose ensure the life and longitivity.
Thumbnail for Practical demonstration and deserve
Which computer software do you use for creating the panel drawing/schematic?
Hello. Unfortunately, I don't have any information about the software.
Why Using same color for Phases ABC On the Selector Switch? I would Use Brown Orange Yellow or Any Regional Color code
No problem
can you tel color code in your panel green is ground how about single phase blue or brown thanks
blue is neutral wire and other wires is phase
Good work
Tanks
مرحبا إنه فيديو رائع
I don't even get what the coloring logic for the wires are... 3 phases but all using yellow? Is that actually normal?
Three phases are displayed with one color
No cable markers / wire numbers?
Number=10mm2
@@IET-76 no I mean normally in the European and UK markets all wires must have a number on them. This is shown on the schematic so you can easily identify each wire.
Engineer ,I appreciate your work.please I need the schematic wiring diagram
Thank you. But now I have nothing. I will do this for the next electricity board
i want to training where place
So helpful
Tanks
Hi there! I Am self learnd electrical lover
Tanks
Not too bad. I like to knock off all the sharp edges on the din rail befor i install it.
Removing sharp edges is the right thing to do, but in this circuit board there is no access to sharp edges and it does not destroy safety
@@IET-76 same with the panels I build, it is for my benefit that I avoid cutting my fingers during the build, but once completed, it will be restricted access
آموزش خوبی بود.ممنون
Tanks
Thank you so much sir, please I would like to be your student and to have more studies on this, thanks
Tanks
دم ایرانیا گرم❤
Merci .lotf darid
What kind of switch is that?
Miniature switch and rccb switch
all electrical panel should have diagram and wire code for next person and for doc
what is rccb stand for
Why incoming elect supply connect to MCB switch top side...
I do not understand what you mean
Can you explain more?
Wire labels?
The label of the wires is attached to them at the installation site of the electrical panel
That socket towards the end seems... Weird. It has grounding pins, but no grounding wire connected, and no grounding screw either that I could see. Seems a bit unsafe tbh.
I am watching you from Ghana if you want to learn the work isn't any way to help the person please
Can you explain equipment name please..??
Rccb switch
Miniature switch
Three phase monitoring relay
Load control
Contactor
احسنت
Are you not using Red, Yellow (or White) and Blue for Phases, Black Neutral and Green (or yellow/Green) for earth. Are you switching the Neutral. That's a fail in New Zealand or Australia.
Very good
Tanks
Nic sir
Tanks
Nice.
Tanks
👍
Thanks
سلام داداش سیم نمره ۱.۵ چطوری با وایر شو سبز زدی 😂 وایر شو سبز برا سیم نمره ۶ هست دمت گرم عالی بود
Ghorbunet
OK work
یک اشکال داره سیم رو شماره بندی نکرد
Please let the names of the equipment shows
There is a complete video on the channel about the required devices. The name of the video is Electrical Protection Devices
👍 👍
please can you get me the simplest way of installing CCTV? thank you@@IET-76 🖐
No cables identified,no id on componants,no shrouding on isolator and not door intrlocked. Self tappinf screws through back of panel and sides of panel....perhaps not done in uk.
Nice tnx
Tanks
need diagram
Sure
I upload wiring diagram in description in the future
I don't know bud, I'm a level below this, I'm struggling to even read what the inputs for the wires are supposed to be... N= neutral, ph=phase? auto=?? C=? NC and NO? So... I guess you wire it if you want the contactor to be normally open or normally closed I guess? I mean it's a good effort and the camera quality helps a lot but I'm still a level below this, hard for me to understand. Need to watch the video a few times and others...
Hello my friend. Watch the video a few times. There are also other videos in this channel that talk about all the equipment needed for the electrical panel and all their details can be explained by watching them. You learn more
@@roamaroundtheknowledgeapparently not 🤣 oh well. Find a different channel that supports the viewers
Good
Tanks
No wire numbers ? Hard for the guy who has to trouble shoot later
OMG I used to build a few panels for control jobs why did I not think to use self drilling screws instead of drilling and tapping holes 🤷♂️🤬. Surly you are not mounting the components directly onto the back of the panel though, panels are normally supplied with a steel backplate to mount on
Thank you for your opinion. It was very helpful. But I must say that in this area the conditions are such that you have to draw the electrical panel in this way. Good luck.
Please can I join you
Please can I join you.
Nothing is labeled.
Sir can u tell me how much salary should I gain after 1 year of experience ❓
Hello
It depends on where you live
But in general it has a good income
You got wonderful skill, but hard to follow. There is no schematic diagram
Thank you. Watch the movie a few times, you will learn something
I need someone to teach me industrial electrician
I do this goal
Thanks sir did you teach Online or not Sir ?
Hello, currently there is no online training. We will do this in the future. Good luck
You should keep atleast 2 inch extra wire inside the channel.
فیکسچر دو طرف کانال روهم نزد قطعه لغزش نداشته باشه
Good job, but this panel will not pass US National Electrical Codes, firstly, the panel space is small compared to the number of devices used, a neutral wire is used along the length of the panel, which must be used separately from the busbar, the panel is not grounded, And there is no ground terminal, it is not allowed to install the outlet on the panel body, the wires and terminals do not have address numbers, the main switch is not installed in the right place, and it is not insulated and covered...
That’s an interesting comment. Why is the panel too small, there is ample space for the small amount of heat generated as it only appears to be a 30 amp supply at most 40. The last comment about insulating and covering is even more so, it’s all what we would term fingerproof ( ipx2 I think it is) having watched a lot of electrical videos from your country I am horrified by the amount of exposed copper. I am not having a go, just curious for an explanation
Thank you for your opinion. It was very helpful. But I must say that in this area the conditions are such that you have to draw the electrical panel in this way. Good luck.
The electrical codes are very different from country to another country.And i find the codes in the USA very bad compared with the code in Europe.
EUROPE
E❤
Tanks
wow
Tanks
need with diagram
Ok in the future
❤
Tanks
بوی نفت میده کارشون😅
Please watch non indian videos for professional understanding
@@dsosys im not Indian
Green wires that are not grounds and yellow wires that are hot.....not in my world!