That mod made it even better... Maybe there's still room for more improvements? who knows? To my knowledge, you are the only MF70 expert on all of UA-cam.
Whith collet also is easy.the first masur when collet is insaid the spindle then also masur spindle the end make so:run out collet minus run out spindle = minimum run out. Best regards
Yeasterday, the motor on my milling mashine, the same type as yours, gone broken and your modification is a great perfection using the belt and that castle creation brushless motor.
Good morning, I think that a good improvement would have to be with the original work table of the machine, I see that a new Proxxon brand of a more professional milling machine was acquired, which I do not see as valid, there are countries where acquiring these components is too difficult
Sweet, sweet mods, Volodymyr. 👍 Just wondering; if you were asked to apply the same mods and upgrades to our MF70 units for a fee, how much do you think that would roughly run us?
Basically only a shaft and maybe bearings. But then you will need to make something with engine. In my case I have also replaced engine. You could take a look in this video, how everything made inside ua-cam.com/video/sM5KqNiaeHQ/v-deo.html
@@zhadlun Ох мнеб так же, Волоримир. Очень хотелось бы такой же стержень, что по точнее, ну и конечно конфигурацию с редукторной шестерёнкой (с другого видео), что конвертирует скорость в мощь. Если бы вы приняли заказ, во сколько обошлось бы мне это удовольствие? Заранее благодарю за ответ.
Thank you for sharing your video with us. But easily was possible to remove run out whith grinding because 0/01 or 0/05 also 0/10 mm is not much and white grinding will be exactly ziro. Normally when you buy some accessories for lathe or milling machine of course are not correct and fit white your lathe but machinist must Fix it. Any way thank you again. Best regards sina von Österreich 🇦🇹
With spindle yes, possible to fix with grinding, but then I need also take care about tapper there. Not sure I will be able to do better than it was. But how about a collet. Grinding there will not have a result in my mind…
I bought them some time ago, will need to found updated links to a products. You could just look for er11 collet with 10mm shaft 150mm long. Endmills, any with coating would work.
Good morning, I think that a good improvement would have to be with the original work table of the machine, I see that a new Proxxon brand of a more professional milling machine was acquired, which I do not see as valid, there are countries where acquiring these components is too difficult
That mod made it even better... Maybe there's still room for more improvements? who knows?
To my knowledge, you are the only MF70 expert on all of UA-cam.
I’m machinist and only Itold something from my experience.idont have small machines.
Best regards
Whith collet also is easy.the first masur when collet is insaid the spindle then also masur spindle the end make so:run out collet minus run out spindle = minimum run out.
Best regards
@@sinadaneshkhah8537 Your comments provide knowledge from experience
Yeasterday, the motor on my milling mashine, the same type as yours, gone broken and your modification is a great perfection using the belt and that castle creation brushless motor.
Good morning, I think that a good improvement would have to be with the original work table of the machine, I see that a new Proxxon brand of a more professional milling machine was acquired, which I do not see as valid, there are countries where acquiring these components is too difficult
Sweet, sweet mods, Volodymyr. 👍
Just wondering; if you were asked to apply the same mods and upgrades to our MF70 units for a fee, how much do you think that would roughly run us?
Nice upgrade. Can you add a part list needed for changing the shaft?
Basically only a shaft and maybe bearings. But then you will need to make something with engine. In my case I have also replaced engine. You could take a look in this video, how everything made inside ua-cam.com/video/sM5KqNiaeHQ/v-deo.html
@@zhadlun
Ох мнеб так же, Волоримир. Очень хотелось бы такой же стержень, что по точнее, ну и конечно конфигурацию с редукторной шестерёнкой (с другого видео), что конвертирует скорость в мощь.
Если бы вы приняли заказ, во сколько обошлось бы мне это удовольствие?
Заранее благодарю за ответ.
Thank you for sharing your video with us.
But easily was possible to remove run out whith grinding because 0/01 or 0/05 also 0/10 mm is not much and white grinding will be exactly ziro.
Normally when you buy some accessories for lathe or milling machine of course are not correct and fit white your lathe but machinist must Fix it.
Any way thank you again.
Best regards sina von Österreich 🇦🇹
With spindle yes, possible to fix with grinding, but then I need also take care about tapper there. Not sure I will be able to do better than it was. But how about a collet. Grinding there will not have a result in my mind…
What is the diameter and length of the original spindle?Thanks
Do you have any advice on removing the original spindle bearings?
Why is the proxxon spindel not good ; why work the new spindel better?
For me problem was only a limitation of 3mm mill at the beginning
Hey, where did you get that cnc plate as motor mount ?
I made it by myself long time ago.
What is the standard thread on the spindle of a Proxxon MF70?
i discovered 8*0,75 mm
you will get much better cuts starting from the other y direction ;) also the endmills will last longer
why?
Your endmill were did you buy from?
aliexpress
Good day sir would like to ask if you are selling package spindle upgrade.
No, I’m not selling it
And you create a link for Ali express for your spindle and endmils please
I bought them some time ago, will need to found updated links to a products. You could just look for er11 collet with 10mm shaft 150mm long. Endmills, any with coating would work.
Where did you get the new shaft?
Aliexpress
@@zhadlun link please?
А можно ссылку на вал?
Понятно, значит лучше взять кредит и купить нормальную машину
Threre is a tuning schaft avalible in Germany
Excuse me sr. Wher did you get the mini mill is nice like it.
Some time ago it was original Proxxon MF70. You could found it on Amazon.
Good morning, I think that a good improvement would have to be with the original work table of the machine, I see that a new Proxxon brand of a more professional milling machine was acquired, which I do not see as valid, there are countries where acquiring these components is too difficult