Nice and professional video. I was curious to know what you ended up finding?? Fuel delivery psi does not look like it was a concern. The psi you had was good enough for it to start. Not sure if it was the video sound, or if the engine actually sounded like it had low compression?? It sounded like it was turning over with little resistance. Either way, nice quality on the video.
Hey, i just saw your video and its not a bad video. I did notice a couple things wrong with this video. 1. you didn't check the oil level before cranking. the Maxxforce DT (not 466 DT) has issues with the oil system where not the right amount of oil would cause a no start. 2. ignoring the initial codes that the truck came in. codes are there to tell you there was an issue, I would recommend to start with the codes before doing any other diagnostics. 3. when using the laptop (ServiceMaxx/NEDS), you can tell a lot of what the truck is doing good and wrong. if you know how to read how much the minimum the pressures are supposed to have, then you will have not touched the fuel lines. removing unnecessary components to just later find out it was something simple is something the customer is not willing to pay. for educational purposes, this video is great. you show a good understanding of the fuel/HP oil system and knew to inspect the fuel strainer (since they do clog up and will cause issues). As for the ECM code, yeah, that is a battery/ECM power issue. International trucks are notorious for electrical issues and this ECM code is proof of it. However, there is something I cannot let go... and its that you didn't tell the customer to sell the truck and buy one with a Cummins in it, will save him a headache. (This one is a dealership meme)
Nice information I have a maxxforce dt 9/10 year 2013 and the servicemaxx had been my friend to keep this truck running I still have to learn a lot stuff but at least my truck is still running
I have a 2023 International TT and truck won't start again they just replaced the starter a month ago. I keep hearing if you turn the truck off without it being in Neutral truck won't start. How do you get it to start again. They checked voltage to starter trying to start engine had voltage but starter doesn't work?
why not apply air pressure to the inlet from the high pressure line at the high pressure rail. If you hear air leaking threw the air intake means the o'ring has gone bad and you are losing oil pressure at the oil rail. You wont see alot of fuel when you pull the injectors. You have totally misunderstood how a high pressure oil pump works on the injectors. you need 2500 psi oil pressure just make the engine idle...oil pressure is what pushes the injector down to pump into the cylinder. the most you need for fuel pressure is 60 psi to run. The reason for the rise and fall of the fuel pressure is the release valve for fuel to return to the tank. That is not an issue.... next time check to see if you have a CMP sensor error. If the camshaft sensor goes bad , it wont start...
Hey I have a international 4300 and the battery keep dyeing if don start the truck for a day or two. And do you have any mechanic recommendation in Houston?
David, we don't have any to recommend. We are just north of Houston, you should take a trip up to the shop. We have a lot of customer come from all over. Thanks for watching
I’m responsible for maintaining 7 buses with DT 466 engines. What diagnostic software do you recommend? I would also like access to shop manuals. What about hardware. I run a MacBook, but it looks like I’ll need an android based tablet or laptop.
I have a maxxforce dt 9/10 and I use a servicemaxx and is very good you need to get a regular laptop whit windows 7 and the nexiq connector and I can give you the information from a guy who install the programs in you laptop remotely
I open the timing cover in front of Engine T444e Internattional Engine ang Also the Socket off Sensor will remove After fix the Lines Of Sensor and the Timing Cover I start the Engine but Crank only not Start, mybe what is the Problem of this, Thank you Sir
I have a 4300 it won’t crank to start I didn’t let the gauge cycle I just stared the truck up instantly and it was about to start and half way stopped I got tech out and checked everything and nothing I got a spn 1081 fmi 9 code
*****🇺🇸🎼🎸🎤It takes time 2 accomplish R golds🤗never give up 😇if there’s a will,there is a way 2 successfully R golds 🙏🏽 1 step at a time,like climbing a ladder 2 reach T sky🥰🥁🎹🎶🇺🇸*****
U need to know when your problem occurs, if its crank no start when truck is cold, usually your ipr is bad, if crank no start when warm, or if truck dies when u slow down at the light or stop sign, its usually icp related, could be bad icp or low oil, or oil leak at fuel rail or high pressure fuel/ oil rail.
Angel, thanks for watching, and be sure to subscribe. Troubleshooting can be difficult sometimes and yes, this issue was a tough one because of other work not done by our shop. We found out later the valves were out of adjustment so the engine had low compression. That is why it sounded like no compression during crank up. Next time we will be sure to share the solution. Again thanks for watching and I appreciate the feedback. 🇺🇸💪👊🔧
I like the way you take your time not rushing the judgment good job bro I will be coming your shop
Nice and professional video. I was curious to know what you ended up finding?? Fuel delivery psi does not look like it was a concern. The psi you had was good enough for it to start. Not sure if it was the video sound, or if the engine actually sounded like it had low compression?? It sounded like it was turning over with little resistance. Either way, nice quality on the video.
Hey, i just saw your video and its not a bad video. I did notice a couple things wrong with this video. 1. you didn't check the oil level before cranking. the Maxxforce DT (not 466 DT) has issues with the oil system where not the right amount of oil would cause a no start. 2. ignoring the initial codes that the truck came in. codes are there to tell you there was an issue, I would recommend to start with the codes before doing any other diagnostics. 3. when using the laptop (ServiceMaxx/NEDS), you can tell a lot of what the truck is doing good and wrong. if you know how to read how much the minimum the pressures are supposed to have, then you will have not touched the fuel lines. removing unnecessary components to just later find out it was something simple is something the customer is not willing to pay. for educational purposes, this video is great. you show a good understanding of the fuel/HP oil system and knew to inspect the fuel strainer (since they do clog up and will cause issues). As for the ECM code, yeah, that is a battery/ECM power issue. International trucks are notorious for electrical issues and this ECM code is proof of it.
However, there is something I cannot let go... and its that you didn't tell the customer to sell the truck and buy one with a Cummins in it, will save him a headache. (This one is a dealership meme)
good points, supply power to ecm wire connector always burn will cause no start...
Nice information I have a maxxforce dt 9/10 year 2013 and the servicemaxx had been my friend to keep this truck running I still have to learn a lot stuff but at least my truck is still running
You are not working on dt 466 mechanical that is dt 466E wich is completely different set-up!
Very good diagnostic by making choice to pull injectors and to see what you found 👍
Yes, thanks
Did you do a follow up video on this video.
I was looking for it too
Where’s the follow up video.
I have a 2023 International TT and truck won't start again they just replaced the starter a month ago. I keep hearing if you turn the truck off without it being in Neutral truck won't start. How do you get it to start again. They checked voltage to starter trying to start engine had voltage but starter doesn't work?
Awesome video very good advice on fuel air pressure
Thanks for watching
Excellent videos! Subscribed
Awesome, thank you!
What was the verdict? Did the same injectors work without grease or was it something else like idm or ecm??
why not apply air pressure to the inlet from the high pressure line at the high pressure rail. If you hear air leaking threw the air intake means the o'ring has gone bad and you are losing oil pressure at the oil rail. You wont see alot of fuel when you pull the injectors. You have totally misunderstood how a high pressure oil pump works on the injectors. you need 2500 psi oil pressure just make the engine idle...oil pressure is what pushes the injector down to pump into the cylinder. the most you need for fuel pressure is 60 psi to run. The reason for the rise and fall of the fuel pressure is the release valve for fuel to return to the tank. That is not an issue.... next time check to see if you have a CMP sensor error. If the camshaft sensor goes bad , it wont start...
Love these videos
AAS Transport T.V thanks for the support. 🇺🇸🔧👊🏼🇨🇱💪🏼
That engine sounds like it has ZERO compression...
Where do you find these service manuals or info for the specs?
Do those trucks carry a warm electrical plug for winter? Couldn't find one in mine
great video and channel. very professional.
Incredible Fendt thanks for watching. 🇺🇸🔧👊🏼🇨🇱💪🏼
Did you get it started never saw the second video
Excellent job man
What happen did it turn on was the problems the injectors ?
what diagnose software system are u using?
Did you ever finish this video?
Buenas noches amigo me gustaia ponerme en contacto con usted
Hey I have a international 4300 and the battery keep dyeing if don start the truck for a day or two. And do you have any mechanic recommendation in Houston?
And it’s takes long to start
David, we don't have any to recommend. We are just north of Houston, you should take a trip up to the shop. We have a lot of customer come from all over. Thanks for watching
Has the battery been tested and fuel system serviced?
What’s the address of your shop and contact information?
@@davidkavambi2776 do a google search.
yes, why did that engine sound like it had no compression????????
What will be total cost to fix it?
DT 466E hard starting no power what can i do please help me
Has no compression when cranking????
Injectors out?
Oil would spray all over.
How no compression in motor?
Part 2 of this truck?
Jose Riera thanks for watching. We will get it out ASAP. 👊🏼🔧🇺🇸💪🏼🇨🇱
TAT Express Inc. Really good videos
@@TATEXPRESSINC still can't find the second video.
I’m responsible for maintaining 7 buses with DT 466 engines. What diagnostic software do you recommend? I would also like access to shop manuals. What about hardware. I run a MacBook, but it looks like I’ll need an android based tablet or laptop.
I have a maxxforce dt 9/10 and I use a servicemaxx and is very good you need to get a regular laptop whit windows 7 and the nexiq connector and I can give you the information from a guy who install the programs in you laptop remotely
@@juangomez8186 hey i need this as well but have a 2004 4200 with vt365. Will this work for it?
@@cl91 yes it will work
What if oil leak on injector
Sir, thank you very good Explanation.. I Ask the problem of t444e international did not Start? Thank you Sir
Thanks for watching be sure to subscribe
I open the timing cover in front of Engine T444e Internattional Engine ang Also the Socket off Sensor will remove After fix the Lines Of Sensor and the Timing Cover I start the Engine but Crank only not Start, mybe what is the Problem of this, Thank you Sir
Waiting for the follow-up video
We're getting a miss about every 30 seconds, any Ideas?
Made by Ford?
My truck just shut off no power from the battery
I have a 4300 it won’t crank to start I didn’t let the gauge cycle I just stared the truck up instantly and it was about to start and half way stopped I got tech out and checked everything and nothing I got a spn 1081 fmi 9 code
*****🇺🇸🎼🎸🎤It takes time 2 accomplish R golds🤗never give up 😇if there’s a will,there is a way 2 successfully R golds 🙏🏽 1 step at a time,like climbing a ladder 2 reach T sky🥰🥁🎹🎶🇺🇸*****
M.M.T. Garage Band thanks for the support. We could not do it without you. 🇺🇸🔧👊🏼🇨🇱💪🏼👍🏽
What is a PM
PM = Preventive Maintenance
Have you done a vid on the promaxxxxxx? Lol
90% off these trucks crank no is usually the fuse in the battery box
Always check the fuse in the fuse box 1st.
U need to know when your problem occurs, if its crank no start when truck is cold, usually your ipr is bad, if crank no start when warm, or if truck dies when u slow down at the light or stop sign, its usually icp related, could be bad icp or low oil, or oil leak at fuel rail or high pressure fuel/ oil rail.
Also not bad to carry starting fluid in a dt466.
Spray starting fluid see if it starts and dies right away or stays running
Whats an ipr?
Lol this video was pointless. As he said and mentioned they couldn't figure it out.
Angel, thanks for watching, and be sure to subscribe. Troubleshooting can be difficult sometimes and yes, this issue was a tough one because of other work not done by our shop. We found out later the valves were out of adjustment so the engine had low compression. That is why it sounded like no compression during crank up. Next time we will be sure to share the solution. Again thanks for watching and I appreciate the feedback. 🇺🇸💪👊🔧
Thanks for watching be sure to subscribe. I would recommend finding the source of the oil leak. The system uses high pressure oil to fire injector.
@@TATEXPRESSINC Nice man . I am glad you did not just throw parts at it.
Give the year of the truck at the start.
Thanks for watching
Where's the follow up video