Відео

Do you know how to disable a 2002 model?

Thanks for your video. I just did this after watching and it was very easy.

How did you test to make sure it was the controller?

Can an ezgo rear seat fit on a club car precedent?

Great video

Excellent, thanks!

My EZGO is a 2017 and you cannot disconnect it or it will not run. But you can muffle it and it's way better. It is located under the seat on the passenger side.

I love the video, but have a question... I have a 2007 Columbia Par Car with 48v, I would like to be able to power the rig when the key is turned on only, that way I make sure it won't drain the batteries if a switch was left on!!! Any ideas of where to get a switched 48v as input to the reducer?

What caused it to go bad or drag in the first place? I hear stuff about a run plug not keeping good connection also. So how would one tell if the plug is losing connection or if it’s the brake?

Hitch pitched whirring noise when I get up to high speed an let off the acceleration and more so when I press the break. Is this a likely fix for that?

Outstanding! Thanks man, the directions in the kit were weak but this really helped.

This helped a ton before attempting to add the seat to my cart! Good video

Mine arent screws. I dont know what they are.

What if the bolts don’t just pop in when it’s attached to motor and flush? Tried for hours 🤨

My cart is very weak going up a small incline. Shutters. Do you think motor is bad?

Great video. I just bought the deluxe light kit. I converted my club car precedent to lithium so I also bought a voltage reducer but it does not have pin connector or voltage reducer harness. I’d rather use what you show in your video but the link for that voltage reducer is no longer good. Do you have a link to one like you used?

I think it would be better to use a relay and go off the ignition switch

Is the voltage reducer needed with 4 12v batteries?

Can I spray paint the dc-dc converter black if Id want?

Does the dc-dc converter waste much power, since it's always cnnected to a live battery, or is it negligible? Would it be better to tie the converter to the key switch, then it only go on when key is turned on?

Do you need to have fuses on the 12 volt side on the hot wire?

Perfect video to get the brake off and was able to move my cart when my battery was dead. Thank you for the great video!

Has anyone had an issue with the brakes locking up after this conversion? I installed the RoyPow S51105P. It charged up fine. All lights and horn worked. Old and new battery indicator showed a full charge. I took it down the road and at about 400 feet or so, it just completely locked up. The lights were still working. Had to flip it to tow mode and push it back to the garage.

Why did it fail ?I can't get power to my brake - batteries are charged,

Using the old cable as a handle is genius. Maybe other knew about this tip, but this noob will forever be grateful for this.

Have had two replaced on my 2009 ezgo r x v. I'm getting ready to replace a third one myself in less than three years

Really impressive Video! Our company has developed a battery tray adapted to TXT, I wonder if you're interested.

Why do all these videos suck all of them I can't see what you folks are doing your hand is blocking what your actually doing or your camera is pointed somewhere else

Where do you order your EZ GO TXT parts? I'm looking for the Bracket-TX Battery Brackets like you showed S4855M217.

Credit where it’s due: you did a much better job explaining safety precautions to people. There’s another fellow with a solid channel, but he jumped right into the work and didn’t really mention the ways to avoid having the system live. Most folks are smart enough to flip the switch into tow, but you did a good job explaining how the lead acid batteries are always live. That will surprise and shock some people if they don’t know what to expect. #beenthere Thanks for putting this together. ✌️ 🍻

Never mount to plastic. Always mount against metal to absorb heat and extend its life.

Great video thanks it helped me a lot on install

Do you have video ona missing motor post

my rxv is making a ticking noise - feels like it's from around the driver's side rear wheel - mostly on right urns but sometimes on straightaways - is this a brake issue? spline? bearing? THANKS

Thanks for your time buddy

Great video. Thank you.

Great content!

for those watching this, make sure you do not ground the anode and cathode grounds together.

Would that be the same on a 2014 EZGO RXV

It’s an awesome video but it helps if you show people what you’re doing with the camera you keep on pointing it to the floor or away from what you’re doing so you can’t tell what you’re doing

so I have a issue with my RXV I turn the key on to reverse and I hear a click the brake releases and the reverse alarm comes on but the cart doesn't move I have replaced the solenoid I was told that's the issue. but it didn't help. I found out by accident if I turn the key off and I slightly press the throttle maybe 1 or 2 inches down and turn the key back onto reverse it will do the same noises but then I will feel it slightly move I left off the pedal and press it more works fine can go to forward and it works fine no issues the entire time I drive it unless I stop and turn off the key? any ideas?

Good video sir

Why take the time to zip tie and disconnect all the wires from the positive and negative, when you could just take one wire off any of the other batteries to brake the circuit???

Thank you. Exactly what I was looking for.

Is there a wiring diagram? Also, trying to install blinker and brake light kit and the person that owned the cart before me installed a light kit. I thought it was plug and play, but not sure how they have it wired.

U can’t see the video

Why does my motor have a snap ring on each side of the speed sensor?

Such a shame this was recorded in portrait mode…half a picture!!.

wow