Відео

Hey man, just checking in. How you doing? Any beard updates?

A hanmered in screw will have less hold then a nail..

One thing im confused about. Do you apply mud, then the mesh covered by more mud? Or do you apply mesh first then mud. This isn't clear in the video. Im about to do this to one of those old 70s huge brick fireplaces. Any tips? Its been painted (oil base). After reading comments im going to prime it (spiderwebs and all). I know theres other ways to do this, but i have an unopened bucket of joint compound from my wood paneling cover-up (came out beautifully), so i want to use it. Thanks for the video, its my instruction manual.

Do you have an idea to make quick cement

Thanks for answering my question. Now the next question is how strong is it compared to one that's been screwed in?

I think you’re measuring your beard wrong. It’s supposed to be from bottom lip, so your beard is longer.

I want to know if we shall hammer or screw a screw in the wood

this was so great and genuine thank you.

W beard

Gandalf to Bilbo.

I searched for can you hammer screwd in? Believing you couldn't or shouldn't, and this video came up first. Good one

OMG you look like anotjer person

You look very handsome. I have never understood men and their facial hair.

You made a geopolymer

Every one is a expert on here . Now it's a sheet metal screw. And has any one done there own testing on this (NO) . As the screw is hammered in the grain of the wood it rolls after which at will swell backsas wood is a tactile work media and grips the screw in place and also it a saddle bracket so unless someone removes the screw it will never come out due to it's design characteristic hope this helps .

Sometimes the tools do make the man, Got mine a year ago still not unpacked, but looking at making a jig like yours welded together. Yup, it works proof of concept. I think the idea is to run half the cutter into the wood and start at an edge so it won't stuff in the trench and probably 1/4 in deep cuts. you should stabilize the framing...stiffen it. along with that slide board. It's all about vibration when machining. Any thanks for the testing out.

Without the beard 100 %.

Er sieht ohne Bart 20 Jahre jünger aus!

It’s been three years, and I just saw this today, because I was looking for a DIY lamb chop puppet. You look about 20 or 30 years younger WITHOUT the beard, and with your hair trimmed. You look ALIVE!!!! But that’s just my opinion. 🤷🏽‍♀️😂

Hippies didn't bathe. Glad to hear you shower daily.

Did you regret shaving off your original beard?

Man, shaving that beard is a crime!

No don’t grow it back. Much better with out

I have been thinking of using mix of concreate mix / volcano ash / mix of little pebble sized volcano glass and rock then after I make the bricks from that make same mix but with clay in mix put it on the inside of the fire place then put volcano ash on when still wet pat it in repeat till it does not soak up moisture let it dry for week with fan on low build small fire to cure it and slowly build fire up for one week even was thinking of putting volcano glass in the inside for a sparkly look

Thanks pretty Smart

Best gait I ever seen

did u even really do this?

but can you unscrew a screw that was hammered in?

Hey, I have a similar plan for my basement. How much coverage did a bucket of joint compound get you would you say? I plan on mixing some quickset Portland to get it to set quicker and be stronger at the cost of sanding.

Nice update. Looks great! Times goes by so fast. I remember when you shaved. Your beard was totally black at the time.

Looks so much better!

I seen this movie it call Whats Eating Gilbert Grape

nice job

Good to see you again, and the beard is looking great. I want to add I am glad you wear your hair without shame. More men should just go out with their baldy heads... no plugs, rugs or drugs!

Great info. saving is great.

This is how I screw in every screw

Finally, an update!!!! Looks great.

Let’s goooo beard hut!

Grow dat Beard

be glad a beard grows back so you can be a man again...never shaving mine after seeing this.

Nice honest review. Can you do an update?

Just purchased a Hercules 57673 also had the craftsman dado setup. I was afraid that the wobble would shake the saw to pieces! Fortunately My grandfather also left me an 8" Freud stacked set that does work, however you can only stack up to 3/4" due to the length of the shaft.. Also you cannot remove the riving knife, so you have to use a 10" blade to lengthen the slot. The dado height also is a bit diminished as it only goes up to and inch and 1/8. Made my own Dado insert as well as a zero clearance insert.

Why not shave off the hair though man, you’d look far younger fully bald

Looks better without beard

You look way beter without the beard .

You look much better .

U shaved 5 yrs old beard And began to look 10 yrs younger 😎😎😎

Ive had mines for 2 years now 😳🤯🤯 ur insane cant image cutting mines

I am dealing with the same cast iron vent pipe. My has already 3” pvc in it. I just want to take the whole cast iron off all the way up to the roof. The question is, is it secure to remove without damaging the roof? Please advise.

lol, I'm watching videos to see what I can get away with doing based on what others have done. I was like, "no way is he gonna push that thing over...", so I wasn't surprised you had the split. I was surprised it didn't go through the floor at least ;) Sorry about the bad decision, but it was useful to watch it to approximate what that load of bricks would do, so thanks for that!