Відео

How do you take that dumb nozzle out?

GREAT really GREAT EXPLANATION - Thank you for your expertise!

excellent video, thanks

Great explanation God bless you

I need to replace my old board date on it only goes to 2012. Was installed in 1994

Thank You for the help. I am a hvac contractor curious how my sprinkler system works. Pretty simple.

Having buried drip lines makes this process 3 times harder

You’re my hero. Thank you!

3:53 and there’s my limit! See ya!!👋🏼

For Pete’s sake - get to the point! 3:41

This was a great and helpful video no BS and long story right to the point. Thank keep up the good work.

Thanks for posting the video! I just bought the PGJ at Home Depot and it doesn't come with the Hunter Wrench. You can't buy one there either. Am I missing something here? I need this to adjust the sprinkler, right? People have stolen the wrenches off of the side of the PGP at the store.

Sorry, I know your intentions were good, but you lost credibility when you improperly described the entire subject matter. You kept referring to adjusting the "Radius" when in fact you were describing the "Arc". The radius is a linear measurement as to how far the water is launched and the arc is the degree of circular motion. Both are important, but should not be confused. Otherwise, thanks for your attempt.

One of my zones is not working and i changed the solenoid. Any video about how to troubleshoot shoot it?

Great explanation. This is what a UA-cam video should look like. 👍

Is it left standing in front of the arrow or behind the arrow?

Great vid, super detail, I had no idea there was a filter down in there, tysm!!

I could not understand this video. Use of the word ‘it’s does not help. I cannot see the top of the head and what was being done. Having a camera behind the instructor as if I was working on the device would also help. 😢

Would it be proper to dig a hole under the automatic drain, maybe approx 2 feet deep and fill it with gravel?

"angle of spread", not "radius"

What gauge are those wires?

A great help! Thanks!

Mine is leaking from the radius screw even when turned off.😢

So since they are fixed for the left, how would you adjust it if the sprinkler head is too far left?

yay! this resolved an open sprinkler issue with a new valve and solenoid. Crazy, must have been some debris or bad assembly, but it is working correctly now. Vendors blaming someone's controller should take note that it could be their valve. 😃

Nice job

Now a small leak at base of solenoid when any zone is on... after putting on a new solenoid snug. The old one was dead for the zone. But i dont know if the diaphram of valve could also be bad. I put the solenoid in tight.

Thank you , best instruction on PGJ 's on youtube !

I have water leaking slowly out of the top of my Rainbird 3500.. and I watched your other video about slope issues and I think that is my problem. Can I use a check valve in my 3500 like you did on the Hunter?

Newbe question: The sprinkler head doesn't look like it has a lot of surface area to help it stay put in the ground. Are there collars of other devices to put around the sprinkler head assy to keep it in place? How about pouring a little concrete around the bottom of the base to help it stay in place?

Thanks! Your suggestions fixed our issues

Is it possible to switch a drip end for a small sprayer?

Great video if you only have one sprinkler. You wasted half of your video talking about how to snip and cut the jacket off of the wire instead of showing how to connect multiple sprinklers. You also don't mention which of the two solenoid wires to connect to the common wire or if it makes any difference, which some will be wondering.

excellent video. You made what was confusing, understandable.

Thank you

My cap came off how do I put it back? Looks like a screw is under there.

My sprinkler wires look like Chinese noodles, and are faded to the point that I cannot tell their colors. I am unable to insert new wiring into the plastic conduit/pipe. I am thinking of cutting off a portion of the end of the wires near the stations, and setting up a plastic housing junction box, where I would join them with new wiring. Is this feasible to do?

You lost it at the angle adjuster

How do I raise the angle of the spray to let it shoot higher (not further). I need to miss a close by shrub and don't want to move the shrub.

Really great job, excellent video!

Nice one. Thanks.

Excelente explicación, muchas gracias

Thanks for your help. On to the next fix😊

Great instructions! I'm working on maintaining my system and adding tubing lines to plants. Thank you!

Yeah well my problem is after the google fiber trenching crews got done near my mailbox, my sprinkler head "start" point is pointing directly into my driveway and for the next 130 or so degrees rotation to the right is fanning out onto the driveway/street. I guess there's no other choice but to dig it back out and reposition it?

Imagine that you are looking at the face of a clock. Your left stop is set at 9 o'clock. But you want the left stop set at 11 o'clock. Tell us how to do that.

Great start. It has its own adjustment tool

How do you adjust the sprinkler to go 360 degrees?

Very well explained.. Thank You-

So, to adjust fixed position, you pull out sprinkler head and rotate?