⬇️Scotty’s Top DIY Tools: 1. Bluetooth Scan Tool: amzn.to/2nfvmaD 2. Cheap Scan Tool: amzn.to/2D8Tvae 3. Professional Socket Set: amzn.to/2Bzmccg 4. Wrench Set: amzn.to/2kmBaOU 5. No Charging Required Car Jump Starter: amzn.to/2CthnUU 6. Battery Pack Car Jump Starter: amzn.to/2nrc6qR ⬇️Things used in this video: 1. Actron Scan Tool: amzn.to/2ngeCQJ 2. Hammer: amzn.to/2CyTojG 3. Electrical Cleaner: amzn.to/2yYS0oj 4. Grease: amzn.to/2B1uWaD 5. Ratchet and socket set: amzn.to/2inoxOY 6. Mechanic’s Tool Set: amzn.to/2Bzmccg 7. Big Fan: amzn.to/2Bwiu3A 8. Common Sense 9. Full HD Camera: amzn.to/2AvoEk7 10. My computer for editing / uploading: amzn.to/2i2sKYz 11. Video editing software: amzn.to/2jv5Fhf 12. Thumbnail software: amzn.to/2k7tz6C 🛠Check out my Garage to see what I use every day and highly recommend: www.amazon.com/shop/scottykilmer 👉Follow me on Instagram for the latest news, funnies, and exclusive info / pics: goo.gl/ohy2cA
I just replaced my MAF Sensor in my Chrysler crossfire, it idles better and is a lot smoother until I press the pedal down. If I am in 2nd or 3rd and floor it the car acts as if it's not getting enough air. There's no way I installed it incorrectly. What is going on? I little description of exactly what happens ... I floor it the RPM drops and it acts as if it's about to stall and then it recovers and goes back and forth and it's very erratic. Its only in high RPMs though with aggressive acceleration. I just spent 180$ on the MAF sensor... Please help me, Scotty!
Fixed my car Re: '05 Rendezvous Died While Driving I have this same issue. Replaced: PCM PCV Plugs, wires Gas filter, Crank sensor, Cam sensor Cleaned and checked all grounds. Both o2 sensors. Ignition switch and relay Fuel pressure is 55# all the time. Fuel system has been professionally cleaned twice. the only code I can find is 300 random misfire but not enough to get a light on the dash. Car will run great most of the time. then from a stop touch the gas and it shuts off. It does start right away after. This does happen more after a extended time at idle for say 15 - 20 minutes. I have taken it to two mechanics with no solution. Never does this while straight on driving. Just from a stop and touch the gas. Car has 166,000 miles but looks great. It's been in the family since new. One more think the wire connection near the back of the driver's seat is not corroded at all. I need a fix not another bill with no fix. I have finally found the reason my '05 Rendezvous Died While Driving. Power steering pump relief valve. The pump was stopping the serpentine belt. This caused the engine to stall. I went thru so many possible fixes. This was a stab in the dark. But it worked. When the car stalled I could hear a belt noise. Then the engine stopped. If you pay attention you will most likely be turning the steering wheel. Does not need to be much at all for this to happen.
Scotty you are my favorite mechanic to watch to be a girl and be able to fix my own car and not have other mechanics take advantage of me it is an honor for to listen to the advice that you give thank you❤✌
Well Scotty. That small trick of tapping for being sure that the sensor is the problem, only an experienced honest mechanic knows it, and also Shows it. Thank You for the tip, and video.
I've seen a bunch of michanics on UA-cam through out the years first time coming across you my good sir and you are an awesome teacher 👍 keep up the good work
too much electronic crap on new cars..and it doesn't give you better gas mileage...cop cars don't have all this...like maybe its just for us low life to keep us broke and dealers in the money that global warming scam is working beautifully...at all levels and lots of companies getting rich at our expense...
Excellent tutorial! Many people would be scared to do this themselves, but it would cost at least 100 or more in a shop, can save a lot of money on simple repairs like this!
That electrical grease is becoming very important. Cleaned some throttle body sensors on my 04 jeep. Went to test drive. Idle was wacky. Wasnt b4. Tranny would shift 1st to 3rd or het stuck in 2nd. Knowing there was nothing wrong 30 minites prior. Back in the garage with the engine running , pushed on connectors, idle would straighten out. Gooped up the connectors . ran great. Still runs great. If i hadnt just caused my own issues by "fixing" it , I'd swear the throttle position sensor had crapped out. But no, just a lousy connection. Love your show. Dont know where your getting all your energy ? Coffee ? Red bull ? Cocaine ? None of my concern. Keep up the great vids. You should be on diy network. Subbed
Hay Scotty. Im going to ring that bell to let everyone know what a great mechanic you are. I changed the sensor and she's pearing like a kitten. Thanks for sharing your expertise.
Scotty, you’re my favorite. I chain watch your videos even when I already know about whatever you’re covering in that particular video. I’m young and I know to learn from the guys who’ve been at it forever. I love cars and I love fixing them. Thanks for all the help.
Hi Scott my car stalls when driving for a few seconds and back to normal on till I slow down again when I exhilarating and sometimes lazy to move off, can you help?
Scotty you are the best. Thanks for being funny and making me feel comfortable in keeping care of my car and my daughter's. Amazing how many people will take advantage of a single woman with car problems.
just depends on how far you want to go. This one is fine for generic work, you need a dealer level one for more intense analysis, and they start at 2 grand for EACH model.
You're amazing, Scotty! Even with all of your subscribers and all of your comments, if somebody asks for help, you do not hesitate to reply to them and give them your knowledge. ++Respect.
Scott I have an issue with my 07 f550 V10. It drives fine no rough idle. But when I come to a stop it does. But it fires right up when I turn the key back on. What do you think it could be. I have no codes coming on or check engine light at all.
tons of things can do that. As a mechanic, I get my dealer level scan tool, hook it up to the car, and drive until it acts up. Then it memorizes the bad data, and I play it back and analyze what went wrong. That's the only way to do it, other than wild guessing.
If you like my car help, be sure to watch my live car talk show every saturday morning at 10 AM CST on google events. I answer your car questions LIVE there. Just go to my scotty kilmer channel on youtube saturday morning at 10, and click on the google plus icon on the top right corner. That takes you to the event. You do have to be a member of google plus to ask questions, so join up, it’s all Free.
Thank you Scotty. You are "The GOAT" auto mechanic. This has happened to me twice in two days. Freaked me out! Now that I know what might be wrong, I won't look like some dumb women when I take my vehicle to the mechanic. This is the third time you have diagnosed problems that could be wrong with my vehicle and where spot on. Thank you again. Happy 2022 New Year. Be well, and stay safe. 🐱
pressure test the fuel pump first, that's easy to do. Ignition systems are much more complex requiring a dealer level scan computer or a freeze frame oscilliscope and years of experience
I would assume vacuum leaks on the intake system first, due to the hard to push brakes. Could even be the brake booster, if it uses too much vacuum it will do that and run like crap
My car has been doing this ever since I replaced the fuel pump the fuel filter the camshaft position sensor and the crankshaft position sensor. I just hope it's not the main computer or the fuel injectors or even the timing chain
Yep .... the wife’s Town n Country does this ! Taken it to the dealer and still does it! I am going to take your advice and try to diagnose a little of this myself!! Thanks
If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on UA-cam. I answer your car questions LIVE there. Just check it out at How To Ask A Live Mechanic Car Questions Free On UA-cam . And remember, every TUESDAY I upload a new video, so don’t miss them.
Hi Scotty Kilmer I have a big problem with my 2001 Ford Expedition 5.4 liter and I installed a new fuel pump and filter cause it was turning off out of know where and it keeps doing the same but this time it reaches half tank and idols and turns off and I can't find the problem can you please help me.
@@scottykilmer hello sir, my car Chevrolet cruze automatic 2012 is in some problem and i need your suggestions. When i start the car it starts but after running for a while it automatically gets neutral from driving. And when i stop and start again it gets back to d. Plz help me about it. Also it has some issue in engine check light. Please help sir
Hi Scotty, thank you for all the great advice & Videos.Would a worn out Crankshaft sensor cause my 2007 Rio to stall randomly then startup again after a few minutes?
My 2006 Chevy Impala’s crankshaft position sensor and camshaft position sensor was bad. My car started stalling then dying on me, but the check engine light wouldn’t stay on. If it died on me, it immediately started back up. I hope after replacing both of my sensors that it fixes my issues. I subscribed. You are an amazing mechanic Scotty! ♥️🙏
Update: After replacing both crankshaft and camshaft position sensors, my car is still stalling on me and dying as I’m reversing, coming to a stop and making a turn. What would you advise I do next? Thanks in advance.
Thank You. my engine went of for three days the fitters could not diagnose the problem. I log onto UA-cam key in my report, as I followed the directions my RAV4 2010 came to life just at the turning of key. am so grateful. Crosby.Ghana
If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on UA-cam. I answer your car questions LIVE there. Just check it out at How To Ask A Live Mechanic Car Questions Free On UA-cam . And remember, every TUESDAY I upload a new video, so don’t miss them.
Scotty Kilmer I have a 02 Durango and it turns off any where and is not over heating , anything to this, no codes on board. This very dangerous you have no control when it happens the pcm changed and still doing it.
Good video Scotty! My brother had this happen on his car. I had a 99 Honda Accord that was doing this but no codes would come up. Eventually figured out the ignition switch wires where you put your key in to start it we're burned and shorting out.
I have a 1989 pontiac firebird. lately it has been dying often while driving in traffic. once In a red light, once in reverse and once while turning. it will start right back up. I'd like to get a general idea before spending hundreds of dollars
Viridiana Trevino, you could try techron like I do. works wonders, it cleans out your fuel injectors, if the problem persists, the fuel pump is the culprit, good luck.
Viridiana Trevino, you could try techron like I do. works wonders, it cleans out your fuel injectors, if the problem persists, the fuel pump is the culprit, good luck.
Hello please help me my car rpm goes down while I'm driving and it cuts off po420 code comes up I went to a muffler shop they said my catalytic is not bad to to a mechanic I change the alternate and battery and terminal still.nothing please help
shavoya burger my car was doing the same and I find out my self it was the the temperature sensor cost 20 bucks worth to try think about it if the computer doesn’t know if is cold or hot that’s why the rpm goes up and down is just my case but can be yours too
hi scotty i have a big problem. so i have a 2002 mitubishi eclipse spyder so one day i started my car let it ran for. 10 min since ut wasent started for a while as soon as i drove the car on the road it shut off since then its not starting up i checked the spark plugs ,cam sensor fuel injecters timing belt and every wire i found in the engine. now what should i do
My 98 Z28 did this all of a sudden without any symptoms beforehand. Gauges go crazy Shutdown with no electrical power at all, as if a switch was turned of. But will start back up on its own or soon after. Leaving no error codes. I thoroughly checked and load tested the alternator, and battery, and ground connections. Found the positive terminal on the batt. was barely loose and negative terminal had lots of corrosion. More consistent readings on alternator tests. After a short test drive so far so good. Time will tell. I feel like a dumb a**. I’m a mechanic and I know better, however life has a way of getting in the way of the these simple tasks and things eventually catch up to you. Hope this helps someone.
Scotty, I have the same code for a cam shaft position sensor on a 2004 Mazda 3. Driving at interstate speeds(65-70) the rpms start to fluctuate back and forth and will some times start to shudder so strongly that you can feel it in the car pretty strongly. Most of the time letting off the gas and getting back on will correct it for a short time sometimes 30 seconds sometimes for a couple of minutes. Then when coming to a stop at a redlight or slowing down to turn the rpms will again fluctuate by 500 to 1000 rpm and then when it goes to shift down from 4th to 3rd the car will shut off. I then have to put it in neutral and restart the car. It idles fine otherwise. Other codes are for small evap system leak which i have had for some time, I replaced the purge valve but no luck, I think the charcoal canister or leak test pump may be cracked but no performance issues for 10s of thousands of miles with that. Also a cat below threshold code for some 10 to 20 thousand miles again no major issues from that. What could be my problem. I replaced the cam position sensor with no luck. Any help would be greatly appreciated, great videos. Thanks
they give Scotty a hard time but this video is good info... the very first thing he said is the first thing you need to do is gather information... spot on.... hell I even like the little tap on the sensor trick... never tried that on sensitive electronics only solenoids but what the hay if it works it works. I like the wiggle test on sensor connectors ... especially on older cars that have been apart and unplugged a bunch of times.
My favorite auto repair guy! I've started to hope that it's your videos when I click something off Google. They've all been so informative. Thank you and please keep up the killer videos!
At first, I thought the one video I watched was cheesy (sorry, I was researching on reasons a car would die and then instantly start back up) *BUT* then I decided to give another video a shot... These are funny and informative! Thanks for making them.
Mr Scotty i was kind of sad and depressed. By too much troubles. In life. being homeless and as I was searching for mechanical info for my old car. And after watching your funny video. Realized. We should not. Worry in. life. That much. And. Enjoy life ! Thanks
I have a 2002 Chevy cavalier, the trac light has been coming on randomly and shifting rough. It also died while driving randomly. Any advice? Could it be a sensor? Love to hear back from ya! Awesome videos.
Top guy full of beans .....a friend with a peugeot 107 2007 has crank no start .... plugged it in no codes ......we originally thought it were 2 ignition coils but took them back as we still got no spark on 2 of the 3 spark plugs (2%3 cylonder no. Was firing ) so thinking cam sensor . I've had crank sensor out . But didn't think to tap it to see if it starts . Same with cam sensor ..I'll give it a try . Thanks
I enjoy your videos, I have a 2000 Jeep Cherokee that intermittently cuts out, it seems to happen more when it's warm. I replaced all of the injectors last summer. I replaced the injectors because the code diagnosed #3 injector malfunction. Should I replace my Cam sensor or Crankshaft position sensor or both? Thanks!
Love ur channel simple and on the point but I got a 2000 celica it stars with the foot on the pedal but if won't ram up it goes to 3500 and if I let go of the pedal it dies I put new spark plugs, clean the injectors and make sure their working but it still do the same dont know what to do a little help scotty
Hi Scotty, I really enjoy your videos. You have saved me a lot of money. If you would can I get your advice? I have an 04 impala that will randomly die when stopping or stopped. I have replaced the fuel pump, fuel pump wiring harness, ignition switch, lock cylinder, even the starter. I saw one of your videos about cleaning the throttle body and I was wanting to know if that might help me. You are very knowledgeable and I trust your advice. If so how exactly would I do that on my 04 impala?
After having a ford dealership replace everything else and it still died, I took my car to local mechanic and it was fixed for cheap because it was just that sensor. Thanks ford!
very good video, i appreciate your style very much, i have a question for my car, it is xc90 2007 volvo, the engine will shut off when i am on cruise control, when the speed reaches 80 to 100 km/h it will randomly dies, and then i can start it again, i do not have a scanner, what do you think might be the problem
Great video and would be very helpful if I had that kind of car. What about a 2003 Ford F150 XLT? Where would the tool scanner connect to and where would that sensor be located at on the engine?
Thanks for your informative video. I have a problem with my hyundai I10 which no mechanic is able to diagnose. When I press the clutch while driving sometimes my car dies. Then if I try to start it starts without no issues. Whenever this issue happens it happens 2 to 3 times. This issue happens only when I press my clutch. If you kindly provide some input that will be very helpful. Mostly issue happen when I press the clutch to change gear while slowing down. I Have never faced this issue while doing up-shift to accelerate.
hi scotty im Adel from algeria i think you are the best at what you do and i have a problem in my car its a peugeot 207 1.4 vti cc when i press the gas pedal quickly the car turn off and i dont know why
SCOTTY!!!!!! YOUR ARE AWESOME!!! I love how you are straight to the point and explain everything so simply!!! I could actually do some of my own work with your guidance and what you explained about the strut assembly is exactly what I needed answered. I recently just purchased a pair like that you tested and yup worse then ever. I knew it but with all the prices ranging from very low to high I chose in the middle. What You explained makes perfect sense and I thought it was silly to replace the whole thing. When I did my research on front suspension on the internet, pretty much all the sites said when replacing parts its recommended to replace all components involved. Now after having the new ones installed and it making the worst clunking noises ever my mechanic told me the mounts are bad and to replace only those. That didn't sit right with me . It doesn't make sense that brand new parts only have one part bad. The whole dang thing is junk!! Also, I have a 2003 Kia Sorento and everytime i put gas in it I have to pull the handle slowly and in spurts otherwise it makes a gurgling sound and spits out gas. What is causing this to happen? A filter possibly? Thank you in advance for reading and if you get the time to read my comment and answer It would be greatly appreciated. You go Scotty!!
Thank God for the internet 🙏 It's a blessing or a curse , depending on how you used it . It can make you or break you .this video was exactly what I was lookin for 👌
This one is one of the easiest to repair of your car repair videos, thanks A LOT =] I'm hoping to buy soon an OBD, there's no obd available here in our country still need to buy from other country. =l
Hi Sir, i really love your vids and i enjoyed watching them. please i have some issues with my volkswagen new beetle 2004, the car dies randomly and i have change fuel pump but still same. what do i have to check again. Thanks
Hi scott. Thanks for the videos, theyre quite helpful. Please need help, my nissan maxima 2002 vq35 shut down while driving and the TCS and ABS and Service engine soon light all came up. I parked for a while confused and panicked but 7mins later I started the car and it started but then moved very slowly couldn't accelerate and had a little jerky feel to it. Please I am confused and this is my everyday car to work and back. I will appreciate all the help and insight to solving this issue.
Hi scotty Thanks for your lovely and informative videos. I’m experiencing an issue with my vw golf plus tdi 1.9. Engine dies and battery light comes on while driving the car. Then crank but no start!! It only starts with start spray in air intake. Battery is definitely ok. And there is not any engine code. Can you guide me what’s the issue please?
⬇️Scotty’s Top DIY Tools:
1. Bluetooth Scan Tool: amzn.to/2nfvmaD
2. Cheap Scan Tool: amzn.to/2D8Tvae
3. Professional Socket Set: amzn.to/2Bzmccg
4. Wrench Set: amzn.to/2kmBaOU
5. No Charging Required Car Jump Starter: amzn.to/2CthnUU
6. Battery Pack Car Jump Starter: amzn.to/2nrc6qR
⬇️Things used in this video:
1. Actron Scan Tool: amzn.to/2ngeCQJ
2. Hammer: amzn.to/2CyTojG
3. Electrical Cleaner: amzn.to/2yYS0oj
4. Grease: amzn.to/2B1uWaD
5. Ratchet and socket set: amzn.to/2inoxOY
6. Mechanic’s Tool Set: amzn.to/2Bzmccg
7. Big Fan: amzn.to/2Bwiu3A
8. Common Sense
9. Full HD Camera: amzn.to/2AvoEk7
10. My computer for editing / uploading: amzn.to/2i2sKYz
11. Video editing software: amzn.to/2jv5Fhf
12. Thumbnail software: amzn.to/2k7tz6C
🛠Check out my Garage to see what I use every day and highly recommend:
www.amazon.com/shop/scottykilmer
👉Follow me on Instagram for the latest news, funnies, and exclusive info / pics:
goo.gl/ohy2cA
Scotty Kilmer I have a 1994 dodge grand caravan and it dies when it is driven and jumps on acceleration can you help
Scotty Kilmer Hey Scotty my 2000 Mustang v6 cranks but doesn’t stay running and then it smokes black smoke from under the hood
I just replaced my MAF Sensor in my Chrysler crossfire, it idles better and is a lot smoother until I press the pedal down. If I am in 2nd or 3rd and floor it the car acts as if it's not getting enough air. There's no way I installed it incorrectly. What is going on? I little description of exactly what happens ... I floor it the RPM drops and it acts as if it's about to stall and then it recovers and goes back and forth and it's very erratic. Its only in high RPMs though with aggressive acceleration. I just spent 180$ on the MAF sensor... Please help me, Scotty!
Scotty Kilmer i have a 2001 acura integra , it dies if you dont use it everyday, . It has a bad idle ,
Fixed my car
Re: '05 Rendezvous Died While Driving
I have this same issue.
Replaced:
PCM PCV
Plugs, wires
Gas filter, Crank sensor, Cam sensor
Cleaned and checked all grounds.
Both o2 sensors.
Ignition switch and relay
Fuel pressure is 55# all the time.
Fuel system has been professionally cleaned twice.
the only code I can find is 300 random misfire but not enough to get a light on the dash.
Car will run great most of the time. then from a stop touch the gas and it shuts off. It does start right away after. This does happen more after a extended time at idle for say 15 - 20 minutes. I have taken it to two mechanics with no solution. Never does this while straight on driving. Just from a stop and touch the gas.
Car has 166,000 miles but looks great. It's been in the family since new.
One more think the wire connection near the back of the driver's seat is not corroded at all.
I need a fix not another bill with no fix.
I have finally found the reason my '05 Rendezvous Died While Driving.
Power steering pump relief valve. The pump was stopping the serpentine belt. This caused the engine to stall. I went thru so many possible fixes. This was a stab in the dark. But it worked. When the car stalled I could hear a belt noise. Then the engine stopped. If you pay attention you will most likely be turning the steering wheel. Does not need to be much at all for this to happen.
Scotty you are my favorite mechanic to watch to be a girl and be able to fix my own car and not have other mechanics take advantage of me it is an honor for to listen to the advice that you give thank you❤✌
Terese Berry I only charge 200 bucks for an oil change
@@mandoss3346 Wow. Why so much?
Mango Fresco hustlers
@@mandoss3346 A simple oil change charges less than $100. Depends where you go too.
$200? Now that is insane.
@@JesusBloodSavedMe_1 it's a joke man. An oil change should cost at most $60 for a synthetic including taxes
This guy fixes your car and makes you laugh/happy at the same time. What a legend.
i spill my coffee every time i watch his video
my car die at the stop sign
Your coffee makes you unhappy for a lil while. =]
Frank Smith
He is very disrespectful not funny
Frank Smith sure nuff.
This video from 2010, that boy Scotty been trappin
Facts
@@tqswagga no cap cuz
Trappin slappin cappin and tappin and mappin yo
That Celica hasn't moved an inch since!
@@michaelposey2186 No cap pimp
Well Scotty. That small trick of tapping for being sure that the sensor is the problem, only an experienced honest mechanic knows it, and also Shows it. Thank You for the tip, and video.
x2
Aww I thought he might of tapped the sensor after changing it to see if it cuts out?
MrCapi55 Yeah Scotty breaks out The Hammer. Great Stuff
@@halden11 The check engine light did go off.
So can you check other sensors this way too?
Notice how Scotty's video's are short, simple, and to the point. I like that. Great help. Helps is a godly gift. It's in the Bible.
I've seen a bunch of michanics on UA-cam through out the years first time coming across you my good sir and you are an awesome teacher 👍 keep up the good work
too much electronic crap on new cars..and it doesn't give you better gas mileage...cop cars don't have all this...like maybe its just for us low life to keep us broke and dealers in the money that global warming scam is working beautifully...at all levels and lots of companies getting rich at our expense...
Excellent tutorial!
Many people would be scared to do this themselves, but it would cost at least 100 or more in a shop, can save a lot of money on simple repairs like this!
Mr. Kilmer you're a legend. I've learned a lot from you. Thank you for all of your helpful videos.
This dude Is awsome in person..and a pure genius..I had the liberty to meeting him a few times. Hated he moved out of Houston to the east coast
...so the next time your car randomly dies going down the highway, don't start kicking it, hit it with a hammer!
😃
Got it🤣🤣
i have done that on the side of the road i smashed the hell out of my car with a hammer
😂🤣😂
My toe still hurts
check for vacuum leaks, pray you find one. Cause if not, often a worn out carburetor on that old thing
@scotty kilmer
What happens if i did all of that n the check engine didnt take off 🥺it wont let me reset.
Thanks for your service Scotty
That electrical grease is becoming very important. Cleaned some throttle body sensors on my 04 jeep. Went to test drive. Idle was wacky. Wasnt b4. Tranny would shift 1st to 3rd or het stuck in 2nd. Knowing there was nothing wrong 30 minites prior. Back in the garage with the engine running , pushed on connectors, idle would straighten out. Gooped up the connectors . ran great. Still runs great. If i hadnt just caused my own issues by "fixing" it , I'd swear the throttle position sensor had crapped out. But no, just a lousy connection.
Love your show. Dont know where your getting all your energy ? Coffee ? Red bull ? Cocaine ? None of my concern. Keep up the great vids. You should be on diy network. Subbed
Lol. Great comments 😀
Hay Scotty. Im going to ring that bell to let everyone know what a great mechanic you are. I changed the sensor and she's pearing like a kitten. Thanks for sharing your expertise.
Scotty, you’re my favorite. I chain watch your videos even when I already know about whatever you’re covering in that particular video. I’m young and I know to learn from the guys who’ve been at it forever. I love cars and I love fixing them. Thanks for all the help.
Thanks Scott the Master. I have learned alot from you sir.
Hi Scott my car stalls when driving for a few seconds and back to normal on till I slow down again when I exhilarating and sometimes lazy to move off, can you help?
When he taps it with the hammer , it's the reason I love old school mechanics
Remember to tap not beat it to death.
@@googleuser868 Yeah! The only hammer I had was a 20lb sledge and I then had to replace my whole engine. But now the engine light is off!
Scotty you are the best. Thanks for being funny and making me feel comfortable in keeping care of my car and my daughter's. Amazing how many people will take advantage of a single woman with car problems.
Love these oldies
just depends on how far you want to go. This one is fine for generic work, you need a dealer level one for more intense analysis, and they start at 2 grand for EACH model.
You're amazing, Scotty!
Even with all of your subscribers and all of your comments, if somebody asks for help, you do not hesitate to reply to them and give them your knowledge.
++Respect.
Man you are one happy guy! I want you as my mechanic:)
You are not the only Scotty Kilmer, but you are the best one. thanks for all your videos.💪 😎🔧⚙🚘
Scott I have an issue with my 07 f550 V10. It drives fine no rough idle. But when I come to a stop it does. But it fires right up when I turn the key back on. What do you think it could be. I have no codes coming on or check engine light at all.
Mine was doing that. It was a MAP sensor. Like mass airflow sensor.
Man he busted out of that silverado at the end +1
tons of things can do that. As a mechanic, I get my dealer level scan tool, hook it up to the car, and drive until it acts up. Then it memorizes the bad data, and I play it back and analyze what went wrong. That's the only way to do it, other than wild guessing.
Right scotty
If you like my car help, be sure to watch my live car talk show every saturday morning at 10 AM CST on google events. I answer your car questions LIVE there. Just go to my scotty kilmer channel on youtube saturday morning at 10, and click on the google plus icon on the top right corner. That takes you to the event. You do have to be a member of google plus to ask questions, so join up, it’s all Free.
Thank you Scotty. You are "The GOAT" auto mechanic. This has happened to me twice in two days. Freaked me out! Now that I know what might be wrong, I won't look like some dumb women when I take my vehicle
to the mechanic. This is the third time you have diagnosed problems that could be wrong with my vehicle and where spot on. Thank you again. Happy 2022 New Year. Be well, and stay safe. 🐱
Great job love his videos keep up the good work 👍
pressure test the fuel pump first, that's easy to do. Ignition systems are much more complex requiring a dealer level scan computer or a freeze frame oscilliscope and years of experience
I would assume vacuum leaks on the intake system first, due to the hard to push brakes. Could even be the brake booster, if it uses too much vacuum it will do that and run like crap
My car has been doing this ever since I replaced the fuel pump the fuel filter the camshaft position sensor and the crankshaft position sensor. I just hope it's not the main computer or the fuel injectors or even the timing chain
@@BryanG830probably a leak in one of the little hoses. Not easy to find, but see if you can hear any air leaks when the engine is running.
fantastic videos / always helpful
Yep .... the wife’s Town n Country does this ! Taken it to the dealer and still does it! I am going to take your advice and try to diagnose a little of this myself!! Thanks
Scotty, how many jumps did you make while in the airborne?
03:47 haha that part made me laugh out loud. Thanks scotty for the advice!
I'm beginning to like this guy scottie.. I've learned quite a bit from watching him.. a way to go scottie thanks so much 👍
you sir are hilarious and informative, the best way i learn.thank you for this.
I've got mk6 fiesta 2005... Just stalls when driving / idling.. No error code showing, cleaned throttle body, replaced tps sensor, repositioned relays, cleaned pump filter, new oil filter, cleaned sensor on front wheel arm... Still stalls.. Pls advice Scott!
Fix it?
Scotty you are the King of our planet 🌍 🙏👍
Hahahahaha, Scotty, you're very funny and make my life easy with that videos... Thank you from Puerto Rico!!!
Love this guy... Entertaining and straight forward!
If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on UA-cam. I answer your car questions LIVE there. Just check it out at How To Ask A Live Mechanic Car Questions Free On UA-cam . And remember, every TUESDAY I upload a new video, so don’t miss them.
Hi Scotty Kilmer I have a big problem with my 2001 Ford Expedition 5.4 liter and I installed a new fuel pump and filter cause it was turning off out of know where and it keeps doing the same but this time it reaches half tank and idols and turns off and I can't find the problem can you please help me.
@@scottykilmer hello sir, my car Chevrolet cruze automatic 2012 is in some problem and i need your suggestions. When i start the car it starts but after running for a while it automatically gets neutral from driving. And when i stop and start again it gets back to d. Plz help me about it. Also it has some issue in engine check light. Please help sir
Scotty the man.keep up the good work.love watching your videos!
Hi Scotty, thank you for all the great advice & Videos.Would a worn out Crankshaft sensor cause my 2007 Rio to stall randomly then startup again after a few minutes?
My 2006 Chevy Impala’s crankshaft position sensor and camshaft position sensor was bad. My car started stalling then dying on me, but the check engine light wouldn’t stay on. If it died on me, it immediately started back up. I hope after replacing both of my sensors that it fixes my issues. I subscribed. You are an amazing mechanic Scotty! ♥️🙏
Update: After replacing both crankshaft and camshaft position sensors, my car is still stalling on me and dying as I’m reversing, coming to a stop and making a turn. What would you advise I do next? Thanks in advance.
@@christinamartinez8132 maybe ya fuel pump is going bad
@@boogboog7067 I sold the car and bought a newer one.
@@christinamartinez8132 bless up mami
Thanks for the great video later friend!!!!
At 2:29 I started laughing so bad, I couldn’t breath for a minute. Lmfao
Scotty is so cheesy and is serving me 90s vibes! 👏🏼 👍🏽 ... thanks
Scotty Kilmer the mr. Wizard of car repair. Thanks again Scotty!
Thank You. my engine went of for three days the fitters could not diagnose the problem. I log onto UA-cam key in my report, as I followed the directions my RAV4 2010 came to life just at the turning of key. am so grateful. Crosby.Ghana
"Here's the new one"
*drops it*
Thanks Scotty, your the best.
If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on UA-cam. I answer your car questions LIVE there. Just check it out at How To Ask A Live Mechanic Car Questions Free On UA-cam . And remember, every TUESDAY I upload a new video, so don’t miss them.
Scotty Kilmer I have a 02 Durango and it turns off any where and is not over heating , anything to this, no codes on board. This very dangerous you have no control when it happens the pcm changed and still doing it.
Are we supposed to carry senses and fuel pumps and stuff around with us or what
Sean Sangster
No.
Yes we are supposed to carry our senses with us wherever we go, you cant exactly leave your eyes, ears, noses and mouth at home.
yes, every car i drive has a spare engine in the trunk.
Good video Scotty! My brother had this happen on his car. I had a 99 Honda Accord that was doing this but no codes would come up. Eventually figured out the ignition switch wires where you put your key in to start it we're burned and shorting out.
You're the coolest guy ever ☺️
You are amazing
I have a 1989 pontiac firebird. lately it has been dying often while driving in traffic. once In a red light, once in reverse and once while turning. it will start right back up. I'd like to get a general idea before spending hundreds of dollars
Viridiana Trevino, you could try techron like I do. works wonders, it cleans out your fuel injectors, if the problem persists, the fuel pump is the culprit, good luck.
Viridiana Trevino, you could try techron like I do. works wonders, it cleans out your fuel injectors, if the problem persists, the fuel pump is the culprit, good luck.
Viridiana Trevino, any auto parts store has techron nationwide!
Hello please help me my car rpm goes down while I'm driving and it cuts off po420 code comes up I went to a muffler shop they said my catalytic is not bad to to a mechanic I change the alternate and battery and terminal still.nothing please help
shavoya burger my car was doing the same and I find out my self it was the the temperature sensor cost 20 bucks worth to try think about it if the computer doesn’t know if is cold or hot that’s why the rpm goes up and down is just my case but can be yours too
hi scotty i have a big problem. so i have a 2002 mitubishi eclipse spyder so one day i started my car let it ran for. 10 min since ut wasent started for a while as soon as i drove the car on the road it shut off since then its not starting up i checked the spark plugs ,cam sensor fuel injecters timing belt and every wire i found in the engine. now what should i do
and other stuff i checked
try my video "fixing a car that cranks but doesn't start up"
+Scotty Kilmer. already tried that
Darresh Prasad stale gas?
Check the fuses main box near the engine mate one of the main fuses playing up.
My 98 Z28 did this all of a sudden without any symptoms beforehand. Gauges go crazy Shutdown with no electrical power at all, as if a switch was turned of. But will start back up on its own or soon after. Leaving no error codes. I thoroughly checked and load tested the alternator, and battery, and ground connections. Found the positive terminal on the batt. was barely loose and negative terminal had lots of corrosion. More consistent readings on alternator tests. After a short test drive so far so good. Time will tell. I feel like a dumb a**. I’m a mechanic and I know better, however life has a way of getting in the way of the these simple tasks and things eventually catch up to you. Hope this helps someone.
Scotty, I have the same code for a cam shaft position sensor on a 2004 Mazda 3. Driving at interstate speeds(65-70) the rpms start to fluctuate back and forth and will some times start to shudder so strongly that you can feel it in the car pretty strongly. Most of the time letting off the gas and getting back on will correct it for a short time sometimes 30 seconds sometimes for a couple of minutes. Then when coming to a stop at a redlight or slowing down to turn the rpms will again fluctuate by 500 to 1000 rpm and then when it goes to shift down from 4th to 3rd the car will shut off. I then have to put it in neutral and restart the car. It idles fine otherwise. Other codes are for small evap system leak which i have had for some time, I replaced the purge valve but no luck, I think the charcoal canister or leak test pump may be cracked but no performance issues for 10s of thousands of miles with that. Also a cat below threshold code for some 10 to 20 thousand miles again no major issues from that. What could be my problem. I replaced the cam position sensor with no luck. Any help would be greatly appreciated, great videos. Thanks
Hey Andy do you know where the camshaft position sensors are located ?. Please help
What was the issue? I’m having the same problem
what if there is no scan code.
Then you are driving a POS car...lol
Billie Bartley AutoZone or O'Reilly's can test it with their scan tool for free
Same trick applys on girlfriend too😜🔨
Hit her with a hammer she dies?
and remember! lol
that boy scotty a wild one
they give Scotty a hard time but this video is good info... the very first thing he said is the first thing you need to do is gather information... spot on.... hell I even like the little tap on the sensor trick... never tried that on sensitive electronics only solenoids but what the hay if it works it works. I like the wiggle test on sensor connectors ... especially on older cars that have been apart and unplugged a bunch of times.
You're fucking cute
Scotty is my favorite.
Scotty. I have been watching u not so long ago and these older videos are great. And have hardly change 👍
My favorite auto repair guy! I've started to hope that it's your videos when I click something off Google. They've all been so informative. Thank you and please keep up the killer videos!
i DID replace camshaft sensor recently. It drives better, doesnt die when driving but it does die sometimes when just sitting and idling.
At first, I thought the one video I watched was cheesy (sorry, I was researching on reasons a car would die and then instantly start back up) *BUT* then I decided to give another video a shot... These are funny and informative! Thanks for making them.
on my toyota pick up 1992 the problem was the cooling sensor temperature/ and the thermostat i change it and now runs like champ
Thank you Scotty, you are genius, very straight forward man.
Mr Scotty i was kind of sad and depressed. By too much troubles. In life. being homeless and as I was searching for mechanical info for my old car. And after watching your funny video. Realized. We should not. Worry in. life. That much. And. Enjoy life ! Thanks
Would this include stalling out after turning on the car.?
Best video I’ve ever seen. Just had this happen lots recently.
This man is really perfect in a lot of ways.
This guy is a riot! And good information to boot.
I have a 2002 Chevy cavalier, the trac light has been coming on randomly and shifting rough. It also died while driving randomly. Any advice? Could it be a sensor? Love to hear back from ya! Awesome videos.
Top guy full of beans .....a friend with a peugeot 107 2007 has crank no start .... plugged it in no codes ......we originally thought it were 2 ignition coils but took them back as we still got no spark on 2 of the 3 spark plugs (2%3 cylonder no. Was firing ) so thinking cam sensor . I've had crank sensor out . But didn't think to tap it to see if it starts . Same with cam sensor ..I'll give it a try . Thanks
I enjoy your videos, I have a 2000 Jeep Cherokee that intermittently cuts out, it seems to happen more when it's warm. I replaced all of the injectors last summer. I replaced the injectors because the code diagnosed #3 injector malfunction. Should I replace my Cam sensor or Crankshaft position sensor or both? Thanks!
Love ur channel simple and on the point but I got a 2000 celica it stars with the foot on the pedal but if won't ram up it goes to 3500 and if I let go of the pedal it dies I put new spark plugs, clean the injectors and make sure their working but it still do the same dont know what to do a little help scotty
Hi Scotty, I really enjoy your videos. You have saved me a lot of money. If you would can I get your advice? I have an 04 impala that will randomly die when stopping or stopped. I have replaced the fuel pump, fuel pump wiring harness, ignition switch, lock cylinder, even the starter. I saw one of your videos about cleaning the throttle body and I was wanting to know if that might help me. You are very knowledgeable and I trust your advice. If so how exactly would I do that on my 04 impala?
I bought Lemur's BlueDriver over a year ago. Love it
After having a ford dealership replace everything else and it still died, I took my car to local mechanic and it was fixed for cheap because it was just that sensor. Thanks ford!
very good video, i appreciate your style very much,
i have a question for my car, it is xc90 2007 volvo, the engine will shut off when i am on cruise control,
when the speed reaches 80 to 100 km/h it will randomly dies, and then i can start it again,
i do not have a scanner, what do you think might be the problem
Great video and would be very helpful if I had that kind of car. What about a 2003 Ford F150 XLT? Where would the tool scanner connect to and where would that sensor be located at on the engine?
Thanks for your informative video. I have a problem with my hyundai I10 which no mechanic is able to diagnose. When I press the clutch while driving sometimes my car dies. Then if I try to start it starts without no issues. Whenever this issue happens it happens 2 to 3 times. This issue happens only when I press my clutch. If you kindly provide some input that will be very helpful. Mostly issue happen when I press the clutch to change gear while slowing down. I Have never faced this issue while doing up-shift to accelerate.
thanks for giving me knowledge and putting a smile on my face at the same time
hi scotty im Adel from algeria i think you are the best at what you do and i have a problem in my car its a peugeot 207 1.4 vti cc when i press the gas pedal quickly the car turn off and i dont know why
SCOTTY!!!!!! YOUR ARE AWESOME!!! I love how you are straight to the point and explain everything so simply!!! I could actually do some of my own work with your guidance and what you explained about the strut assembly is exactly what I needed answered. I recently just purchased a pair like that you tested and yup worse then ever. I knew it but with all the prices ranging from very low to high I chose in the middle. What You explained makes perfect sense and I thought it was silly to replace the whole thing. When I did my research on front suspension on the internet, pretty much all the sites said when replacing parts its recommended to replace all components involved. Now after having the new ones installed and it making the worst clunking noises ever my mechanic told me the mounts are bad and to replace only those. That didn't sit right with me . It doesn't make sense that brand new parts only have one part bad. The whole dang thing is junk!! Also, I have a 2003 Kia Sorento and everytime i put gas in it I have to pull the handle slowly and in spurts otherwise it makes a gurgling sound and spits out gas. What is causing this to happen? A filter possibly? Thank you in advance for reading and if you get the time to read my comment and answer It would be greatly appreciated. You go Scotty!!
Mazda. What I’m having trouble with ;) Love that you SHOW exact problem, recreate it, then fix it. Thanks Scotty!
Thank God for the internet 🙏
It's a blessing or a curse , depending on how you used it . It can make you or break you .this video was exactly what I was lookin for 👌
This one is one of the easiest to repair of your car repair videos, thanks A LOT =]
I'm hoping to buy soon an OBD, there's no obd available here in our country still need to buy from other country. =l
Oh man you always make me laugh, even when I don’t know what’s going on with my car😂
hi Scotty your the best. best way to check your cam sensor with out a multimeter
Hi Sir, i really love your vids and i enjoyed watching them. please i have some issues with my volkswagen new beetle 2004, the car dies randomly and i have change fuel pump but still same. what do i have to check again. Thanks
Hi scott. Thanks for the videos, theyre quite helpful.
Please need help, my nissan maxima 2002 vq35 shut down while driving and the TCS and ABS and Service engine soon light all came up.
I parked for a while confused and panicked but 7mins later I started the car and it started but then moved very slowly couldn't accelerate and had a little jerky feel to it.
Please I am confused and this is my everyday car to work and back.
I will appreciate all the help and insight to solving this issue.
Hi scotty
Thanks for your lovely and informative videos.
I’m experiencing an issue with my vw golf plus tdi 1.9.
Engine dies and battery light comes on while driving the car.
Then crank but no start!! It only starts with start spray in air intake. Battery is definitely ok. And there is not any engine code. Can you guide me what’s the issue please?
1:58 If you have a problem smack it with a hammer. LOL that was my grandfather's favorite tool.